X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2FVCMA9.h;h=ebe9e424c329ff25419dc6fd21f899e7b50d3019;hb=2a9a2339a4ea04636ed0968e76eeaf784e987f52;hp=5e614fd8e8186bd9094f5b4b855a0933e0a32ea0;hpb=dfc91c33957c95da34e3888dc87912d5c15a7603;p=u-boot diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h index 5e614fd8e8..ebe9e424c3 100644 --- a/include/configs/VCMA9.h +++ b/include/configs/VCMA9.h @@ -2,7 +2,7 @@ * (C) Copyright 2002, 2003 * Sysgo Real-Time Solutions, GmbH * Marius Groeger - * Gary Jennejohn + * Gary Jennejohn * David Mueller * * Configuation settings for the MPL VCMA9 board. @@ -33,9 +33,10 @@ * High Level Configuration Options * (easy to change) */ -#define CONFIG_ARM920T 1 /* This is an ARM920T Core */ -#define CONFIG_S3C2410 1 /* in a SAMSUNG S3C2410 SoC */ -#define CONFIG_VCMA9 1 /* on a MPL VCMA9 Board */ +#define CONFIG_ARM920T 1 /* This is an ARM920T Core */ +#define CONFIG_S3C24X0 1 /* in a SAMSUNG S3C24x0-type SoC */ +#define CONFIG_S3C2410 1 /* specifically a SAMSUNG S3C2410 SoC */ +#define CONFIG_VCMA9 1 /* on a MPL VCMA9 Board */ /* input clock of PLL */ #define CONFIG_SYS_CLK_FREQ 12000000/* VCMA9 has 12MHz input clock */ @@ -100,7 +101,6 @@ * Size of malloc() pool */ /*#define CONFIG_MALLOC_SIZE (CONFIG_ENV_SIZE + 128*1024)*/ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CONFIG_SYS_MONITOR_LEN (256 * 1024) #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* BUNZIP2 needs a lot of RAM */ @@ -108,9 +108,10 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x20000300 -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x20000300 +#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */ #define CONFIG_DRIVER_S3C24X0_I2C 1 /* we use the buildin I2C controller */ @@ -129,7 +130,7 @@ #define CONFIG_DOS_PARTITION 1 /* Enable needed helper functions */ -#define CONFIG_SYS_DEVICE_DEREGISTER /* needs device_deregister */ +#define CONFIG_SYS_STDIO_DEREGISTER /* needs stdio_deregister */ /************************************************************ * RTC @@ -246,42 +247,4 @@ #define MULTI_PURPOSE_SOCKET_ADDR 0x08000000 -/*----------------------------------------------------------------------- - * NAND flash settings - */ -#if defined(CONFIG_CMD_NAND) - -#define CONFIG_NAND_LEGACY -#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 - -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 - -#define NAND_WAIT_READY(nand) NF_WaitRB() - -#define NAND_DISABLE_CE(nand) NF_SetCE(NFCE_HIGH) -#define NAND_ENABLE_CE(nand) NF_SetCE(NFCE_LOW) - - -#define WRITE_NAND_COMMAND(d, adr) NF_Cmd(d) -#define WRITE_NAND_COMMANDW(d, adr) NF_CmdW(d) -#define WRITE_NAND_ADDRESS(d, adr) NF_Addr(d) -#define WRITE_NAND(d, adr) NF_Write(d) -#define READ_NAND(adr) NF_Read() -/* the following functions are NOP's because S3C24X0 handles this in hardware */ -#define NAND_CTL_CLRALE(nandptr) -#define NAND_CTL_SETALE(nandptr) -#define NAND_CTL_CLRCLE(nandptr) -#define NAND_CTL_SETCLE(nandptr) - -#define CONFIG_MTD_NAND_VERIFY_WRITE 1 -#define CONFIG_MTD_NAND_ECC_JFFS2 1 - -#endif - #endif /* __CONFIG_H */