X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2FW7OLMC.h;h=462b155a301131193eddbbf85d8dcd41631d7008;hb=0a7bec7f991950da90c6ee6bc59f322abebccbb7;hp=ceef76eeaf67ed3d054b546d51df24db2a6a4b4d;hpb=dfc91c33957c95da34e3888dc87912d5c15a7603;p=u-boot

diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h
index ceef76eeaf..462b155a30 100644
--- a/include/configs/W7OLMC.h
+++ b/include/configs/W7OLMC.h
@@ -38,8 +38,11 @@
 #define CONFIG_W7O		1		/* ...on a Wave 7 Optics board	*/
 #define CONFIG_W7OLMC		1		/* ...specifically an LMC	*/
 
+#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
+
 #define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f	*/
 #define	CONFIG_MISC_INIT_F	1		/* and misc_init_f()		*/
+#define	CONFIG_MISC_INIT_R	1		/* and misc_init_r()		*/
 
 #define CONFIG_SYS_CLK_FREQ	33333333	/* external frequency to pll	*/
 
@@ -109,7 +112,6 @@
 #define CONFIG_SYS_PROMPT		"Wave7Optics> " /* Monitor Command Prompt	*/
 #undef  CONFIG_SYS_HUSH_PARSER				/* No hush parse for U-Boot       */
 #ifdef  CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 #endif
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
@@ -123,6 +125,12 @@
 #define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on		*/
 #define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/
 
+#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
+
 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK			/* external serial clock */
 #define CONFIG_SYS_405_UART_ERRATA_59			/* 405GP/CR Rev. D silicon */
 #define CONFIG_SYS_BASE_BAUD		384000
@@ -206,9 +214,9 @@
 #define CONFIG_SYS_EBC_PB5CR   0xFD21A000
 
 /* bank 6 is unused */
-/* pb6ap = 0 */
+/* PB6AP = 0 */
 #define CONFIG_SYS_EBC_PB6AP   0x00000000
-/* pb6cr = 0 */
+/* PB6CR = 0 */
 #define CONFIG_SYS_EBC_PB6CR   0x00000000
 
 /* bank 7 is LED register */
@@ -271,6 +279,7 @@
  * I2C EEPROM (CAT24WC08) for environment
  */
 #define CONFIG_HARD_I2C			/* I2c with hardware support */
+#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
@@ -302,20 +311,10 @@
  * Definitions for initial stack pointer and data area (in RAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM	*/
-#define CONFIG_SYS_GBL_DATA_SIZE	64		/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM		0x02		/* Software reboot		*/
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use	*/