X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Falpr.h;h=2782e559f5fabd6228e90ed15075ab473be71244;hb=ffb96d55d13759a7e4fe4ba5fc5e3eb6fac11738;hp=f0a89623c3ba7557d7ca20633c5ea0ad3c96ccea;hpb=9cc18042e61275210cf888e5759347eeb2a2e297;p=u-boot

diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index f0a89623c3..2782e559f5 100644
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -14,7 +14,6 @@
 #define CONFIG_ALPR		1	    /* Board is ebony		*/
 #define CONFIG_440GX		1	    /* Specifc GX support	*/
 #define CONFIG_440		1	    /* ... PPC440 family	*/
-#define CONFIG_4xx		1	    /* ... PPC4xx family	*/
 #define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_pre_init	*/
 #define CONFIG_LAST_STAGE_INIT	1	    /* call last_stage_init()	*/
 
@@ -223,6 +222,7 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_FPGA
+#define CONFIG_CMD_FPGA_LOADMK
 #define CONFIG_CMD_I2C
 #undef CONFIG_CMD_LOADB
 #undef CONFIG_CMD_LOADS
@@ -238,7 +238,6 @@
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
@@ -255,8 +254,6 @@
 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
 #define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
 
-#define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */
-
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_LOOPW            1       /* enable loopw command         */
 #define CONFIG_MX_CYCLIC	1       /* enable mdc/mwc commands      */
@@ -327,6 +324,8 @@
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2,	\
 				  CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 }
 #define CONFIG_SYS_NAND_QUIET_TEST	1	/* don't warn upon unknown NAND flash	*/
+#define CONFIG_SYS_NAND_MAX_OOBFREE	2
+#define CONFIG_SYS_NAND_MAX_ECCPOS	56
 
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
@@ -350,7 +349,6 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 
 /* pass open firmware flat tree */