X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fdavinci_sffsdr.h;h=c931ede85cfd7d79851fc6f0b03248ac421f526d;hb=79874ae9341d000d7428ae05d3bce54d90adb81c;hp=875bab6f7dd70759892f5f379201d8077e63b4cf;hpb=ef29884b2708a6cce3b77f4ccaeea193d4e02c22;p=u-boot

diff --git a/include/configs/davinci_sffsdr.h b/include/configs/davinci_sffsdr.h
index 875bab6f7d..c931ede85c 100644
--- a/include/configs/davinci_sffsdr.h
+++ b/include/configs/davinci_sffsdr.h
@@ -22,20 +22,18 @@
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
-#include <asm/sizes.h>
 
 /* Board */
 #define SFFSDR
 #define CONFIG_SYS_NAND_LARGEPAGE
 #define CONFIG_SYS_USE_NAND
-#define CONFIG_SYS_USE_DSPLINK		/* This is to prevent U-Boot from
-				 * powering ON the DSP. */
+#define CONFIG_SYS_USE_DSPLINK		/* don't power up the DSP. */
 /* SoC Configuration */
 #define CONFIG_ARM926EJS			/* arm926ejs CPU core */
-#define CONFIG_SYS_CLK_FREQ	297000000	/* Arm Clock frequency */
 #define CONFIG_SYS_TIMERBASE		0x01c21400	/* use timer 0 */
 #define CONFIG_SYS_HZ_CLOCK		27000000	/* Timer Input clock freq */
 #define CONFIG_SYS_HZ			1000
+#define CONFIG_SOC_DM644X
 /* EEPROM definitions for Atmel 24LC64 EEPROM chip */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
@@ -43,7 +41,6 @@
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
 /* Memory Info */
 #define CONFIG_SYS_MALLOC_LEN		(0x10000 + 256*1024)	/* malloc() len */
-#define CONFIG_SYS_GBL_DATA_SIZE	128		/* reserved for initial data */
 #define CONFIG_SYS_MEMTEST_START	0x80000000	/* memtest start address */
 #define CONFIG_SYS_MEMTEST_END		0x81000000	/* 16MB RAM test */
 #define CONFIG_NR_DRAM_BANKS	1		/* we have 1 bank of DRAM */
@@ -54,9 +51,9 @@
 /* Serial Driver info */
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	4		/* NS16550 register size */
+#define CONFIG_SYS_NS16550_REG_SIZE	-4	/* NS16550 register size, byteorder */
 #define CONFIG_SYS_NS16550_COM1	0x01c20000	/* Base address of UART0 */
-#define CONFIG_SYS_NS16550_CLK		27000000	/* Input clock to NS16550 */
+#define CONFIG_SYS_NS16550_CLK	CONFIG_SYS_HZ_CLOCK	/* Input clock to NS16550 */
 #define CONFIG_CONS_INDEX	1		/* use UART0 for console */
 #define CONFIG_BAUDRATE		115200		/* Default baud rate */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
@@ -77,11 +74,12 @@
 /* Flash & Environment */
 #undef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_SYS_NO_FLASH
+#define CONFIG_NAND_DAVINCI
+#define CONFIG_SYS_NAND_CS		2
 #define CONFIG_ENV_IS_IN_NAND		/* U-Boot env in NAND Flash  */
 #define CONFIG_ENV_SECT_SIZE	2048	/* Env sector Size */
-#define CONFIG_ENV_SIZE		SZ_128K
+#define CONFIG_ENV_SIZE		(128 << 10)	/* 128 KiB */
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */
-#define CONFIG_SKIP_RELOCATE_UBOOT	/* to a proper address, init done */
 #define CONFIG_SYS_NAND_BASE		0x02000000
 #define CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND devices */
@@ -142,9 +140,17 @@
 #undef CONFIG_CMD_SETGETDCR
 #undef CONFIG_CMD_FLASH
 #undef CONFIG_CMD_IMLS
-/* KGDB support (if any) */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
+
+#ifdef CONFIG_CMD_BDI
+#define CONFIG_CLOCKS
 #endif
+
+#define CONFIG_MAX_RAM_BANK_SIZE	(256 << 20)	/* 256 MB */
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + \
+					 CONFIG_SYS_INIT_RAM_SIZE - \
+					 GENERATED_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */