X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fdevkit3250.h;h=d12f37150b3425493401fe9703e9a5ebb3705f7e;hb=e883ffe00b6db807544c70e743cf7832d5d56d40;hp=a71f67c352bbcb50e2a37872817f01598f3929bc;hpb=c14d4b0051df5f569fa33d9937af1db267ed6d34;p=u-boot

diff --git a/include/configs/devkit3250.h b/include/configs/devkit3250.h
index a71f67c352..d12f37150b 100644
--- a/include/configs/devkit3250.h
+++ b/include/configs/devkit3250.h
@@ -1,9 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Embest/Timll DevKit3250 board configuration file
  *
  * Copyright (C) 2011-2015 Vladimir Zapolskiy <vz@mleia.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #ifndef __CONFIG_DEVKIT3250_H__
@@ -13,10 +12,6 @@
 #include <linux/sizes.h>
 #include <asm/arch/cpu.h>
 
-/*
- * Define DevKit3250 machine type by hand until it lands in mach-types
- */
-#define MACH_TYPE_DEVKIT3250		3697
 #define CONFIG_MACH_TYPE		MACH_TYPE_DEVKIT3250
 
 #define CONFIG_SYS_ICACHE_OFF
@@ -24,7 +19,6 @@
 #if !defined(CONFIG_SPL_BUILD)
 #define CONFIG_SKIP_LOWLEVEL_INIT
 #endif
-#define CONFIG_BOARD_EARLY_INIT_F
 
 /*
  * Memory configurations
@@ -33,7 +27,6 @@
 #define CONFIG_SYS_MALLOC_LEN		SZ_1M
 #define CONFIG_SYS_SDRAM_BASE		EMC_DYCS0_BASE
 #define CONFIG_SYS_SDRAM_SIZE		SZ_64M
-#define CONFIG_SYS_TEXT_BASE		0x83F00000
 #define CONFIG_SYS_MEMTEST_START	(CONFIG_SYS_SDRAM_BASE + SZ_32K)
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_TEXT_BASE - SZ_1M)
 
@@ -46,7 +39,6 @@
  * Serial Driver
  */
 #define CONFIG_SYS_LPC32XX_UART		5   /* UART5 */
-#define CONFIG_BAUDRATE			115200
 
 /*
  * DMA
@@ -70,7 +62,6 @@
 /*
  * SSP/SPI
  */
-#define CONFIG_LPC32XX_SSP
 #define CONFIG_LPC32XX_SSP_TIMEOUT	100000
 
 /*
@@ -79,8 +70,6 @@
 #define CONFIG_RMII
 #define CONFIG_PHY_SMSC
 #define CONFIG_LPC32XX_ETH
-#define CONFIG_PHYLIB
-#define CONFIG_PHY_ADDR			0x1F
 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 
 /*
@@ -116,9 +105,6 @@
 #define CONFIG_SYS_NAND_PAGE_SIZE		NAND_LARGE_BLOCK_PAGE_SIZE
 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NAND
-
 /*
  * USB
  */
@@ -128,17 +114,9 @@
 /*
  * U-Boot General Configurations
  */
-#define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_CBSIZE		1024
-#define CONFIG_SYS_PBSIZE		\
-	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
 
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_DOS_PARTITION
-
 /*
  * Pass open firmware flat tree
  */
@@ -146,7 +124,6 @@
 /*
  * Environment
  */
-#define CONFIG_ENV_IS_IN_NAND		1
 #define CONFIG_ENV_SIZE			SZ_128K
 #define CONFIG_ENV_OFFSET		0x000A0000
 
@@ -177,7 +154,6 @@
 #define CONFIG_SETUP_MEMORY_TAGS
 
 #define CONFIG_BOOTFILE			"uImage"
-#define CONFIG_BOOTARGS			"console=ttyS0,115200n8"
 #define CONFIG_LOADADDR			0x80008000
 
 /*
@@ -188,15 +164,12 @@
 
 /* SPL will use SRAM as stack */
 #define CONFIG_SPL_STACK		0x0000FFF8
-#define CONFIG_SPL_BOARD_INIT
 
 /* Use the framework and generic lib */
-#define CONFIG_SPL_FRAMEWORK
 
 /* SPL will use serial */
 
 /* SPL loads an image from NAND */
-#define CONFIG_SPL_NAND_SIMPLE
 #define CONFIG_SPL_NAND_RAW_ONLY
 #define CONFIG_SPL_NAND_DRIVERS