X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fedminiv2.h;h=a75f06aa5950d7c940a933b92d4c3511476332cd;hb=2a9a2339a4ea04636ed0968e76eeaf784e987f52;hp=055931cda63ed8f2370b319a45f26230acaf5832;hpb=50298d37e698a6c730eacf1811da5e7011e20113;p=u-boot

diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h
index 055931cda6..a75f06aa59 100644
--- a/include/configs/edminiv2.h
+++ b/include/configs/edminiv2.h
@@ -60,7 +60,7 @@
 
 #define ORION5X_MPP0_7		0x00000003
 #define ORION5X_MPP8_15		0x55550000
-#define ORION5X_MPP16_23	0x00000000
+#define ORION5X_MPP16_23	0x00005555
 
 /*
  * Board-specific values for Orion5x GPIO low level init:
@@ -131,6 +131,8 @@
  * Commands configuration - using default command set for now
  */
 #include <config_cmd_default.h>
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_I2C
 
 /*
  * Network
@@ -149,6 +151,47 @@
 #define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
 #endif
 
+/*
+ * IDE
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_IDE_PREINIT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+/* ED Mini V has an IDE-compatible SATA connector for port 1 */
+#define CONFIG_MVSATA_IDE
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE		4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* A single bus, a single device */
+#define CONFIG_SYS_IDE_MAXBUS		1
+#define CONFIG_SYS_IDE_MAXDEVICE	1
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR	ORION5X_SATA_BASE
+/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
+#define CONFIG_SYS_ATA_IDE0_OFFSET	ORION5X_SATA_PORT1_OFFSET
+/* end of IDE defines */
+#endif /* CMD_IDE */
+
+/*
+ * I2C related stuff
+ */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_I2C_MVTWSI
+#define CONFIG_I2C_MVTWSI_BASE		ORION5X_TWSI_BASE
+#define CONFIG_SYS_I2C_SLAVE		0x0
+#define CONFIG_SYS_I2C_SPEED		100000
+#endif
+
 /*
  *  Environment variables configurations
  */
@@ -162,7 +205,6 @@
  */
 #define CONFIG_SYS_MALLOC_LEN	(1024 * 128) /* 128kB for malloc() */
 /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE	128
 
 /*
  * Other required minimal configurations
@@ -180,4 +222,9 @@
 #define CONFIG_SYS_RESET_ADDRESS	0xffff0000
 #define CONFIG_SYS_MAXARGS		16
 
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0
+#define CONFIG_SYS_INIT_SP_ADDR	\
+	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
 #endif /* _CONFIG_EDMINIV2_H */