X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fkm82xx.h;h=1f9c7205aee59c44b574f886976b4d8cb348275c;hb=2ae9fbe00f71b8e48a04a13a71a9f6b42b70f158;hp=b087cdb24045fd231c01d6986c6190e82cf21936;hpb=1a4596601fd395f3afb8f82f3f840c5e00bdd57a;p=u-boot

diff --git a/include/configs/km82xx.h b/include/configs/km82xx.h
index b087cdb240..1f9c7205ae 100644
--- a/include/configs/km82xx.h
+++ b/include/configs/km82xx.h
@@ -2,7 +2,7 @@
  * (C) Copyright 2007-2011
  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
  *
- * SPDX-License-Identifier:	GPL-2.0+ 
+ * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -29,8 +29,12 @@
 #error ("Board unsupported")
 #endif
 
+#define CONFIG_DISPLAY_BOARDINFO
+
 #define	CONFIG_SYS_TEXT_BASE	0xFE000000
 
+#define CONFIG_MISC_INIT_R
+
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
@@ -196,7 +200,6 @@
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	CONFIG_KM_BOARD_EXTRA_ENV					\
 	CONFIG_KM_DEF_ENV						\
-	"EEprom_ivm=pca9544a:70:4 \0"					\
 	"unlock=yes\0"							\
 	"newenv="							\
 		"prot off 0xFE0C0000 +0x40000 && "			\
@@ -205,9 +208,6 @@
 	""
 
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
 
 #define CONFIG_SYS_MONITOR_LEN		(768 << 10)
 
@@ -226,10 +226,20 @@
 #endif /* CONFIG_ENV_IS_IN_FLASH */
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		50000	/* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE		0x7F	/* I2C slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_SYS_NUM_I2C_BUSES	3
+#define CONFIG_SYS_I2C_MAX_HOPS		1
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SPEED		CONFIG_SYS_I2C_SOFT_SPEED
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
+#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
+			{0, {{I2C_MUX_PCA9542, 0x70, 0} } }, \
+			{0, {{I2C_MUX_PCA9542, 0x70, 1} } } }
+
+#define CONFIG_KM_IVM_BUS		1	/* I2C2 (Mux-Port 1)*/
+#define CONFIG_KM_I2C_ABORT
 
 /*
  * Software (bit-bang) I2C driver configuration
@@ -264,9 +274,8 @@ int get_scl(void);
 #define CONFIG_DTT_LM75			/* ON Semi's LM75		*/
 #define CONFIG_DTT_SENSORS	{0}	/* Sensor addresses		*/
 #define CONFIG_SYS_DTT_MAX_TEMP	70
-#define CONFIG_SYS_DTT_LOW_TEMP	-30
 #define CONFIG_SYS_DTT_HYSTERESIS	3
-#define CONFIG_SYS_DTT_BUS_NUM		(CONFIG_SYS_MAX_I2C_BUS)
+#define CONFIG_SYS_DTT_BUS_NUM		2
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 
@@ -421,11 +430,6 @@ int get_scl(void);
 
 #define	CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC	/* "bad" address */
 
-/* pass open firmware flat tree */
-#define CONFIG_FIT		1
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #define OF_TBCLK		(bd->bi_busfreq / 4)
 #define OF_STDOUT_PATH		"/soc/cpm/serial@11a90"