X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fml300.h;h=68d0c85e1afc1a130cbfc5c700f30298c78c351b;hb=d3a513c23ba4100d6983161cdc1f747dfd087bbd;hp=0183041842af27139d5f25a5d2a052a7ee1d25c2;hpb=78549bbf44bd2c8d1a0730fb068836071751afaa;p=u-boot diff --git a/include/configs/ml300.h b/include/configs/ml300.h index 0183041842..68d0c85e1a 100644 --- a/include/configs/ml300.h +++ b/include/configs/ml300.h @@ -54,28 +54,29 @@ #define CONFIG_405 1 /* This is a PPC405 CPU */ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_XILINX_405 1 #define CONFIG_XILINX_ML300 1 /* ...on a Xilinx ML300 board */ #define CONFIG_SYSTEMACE 1 #define CONFIG_DOS_PARTITION 1 -#define CFG_SYSTEMACE_BASE XPAR_OPB_SYSACE_0_BASEADDR -#define CFG_SYSTEMACE_WIDTH XPAR_XSYSACE_MEM_WIDTH +#define CONFIG_SYS_SYSTEMACE_BASE XPAR_OPB_SYSACE_0_BASEADDR +#define CONFIG_SYS_SYSTEMACE_WIDTH XPAR_XSYSACE_MEM_WIDTH -#define CFG_ENV_IS_IN_EEPROM 1 /* environment is in EEPROM */ +#define CONFIG_ENV_IS_IN_EEPROM 1 /* environment is in EEPROM */ /* following are used only if env is in EEPROM */ -#ifdef CFG_ENV_IS_IN_EEPROM -#define CFG_I2C_EEPROM_ADDR XPAR_PERSISTENT_0_IIC_0_EEPROMADDR -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_ENV_OFFSET XPAR_PERSISTENT_0_IIC_0_BASEADDR +#ifdef CONFIG_ENV_IS_IN_EEPROM +#define CONFIG_SYS_I2C_EEPROM_ADDR XPAR_PERSISTENT_0_IIC_0_EEPROMADDR +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_ENV_OFFSET XPAR_PERSISTENT_0_IIC_0_BASEADDR #define CONFIG_MISC_INIT_R 1 /* used to call out convert_env() */ #define CONFIG_ENV_OVERWRITE 1 /* allow users to update ethaddr and serial# */ #endif #include "../board/xilinx/ml300/xparameters.h" -#define CFG_NO_FLASH 1 /* no flash */ -#define CFG_ENV_SIZE XPAR_PERSISTENT_0_IIC_0_HIGHADDR - XPAR_PERSISTENT_0_IIC_0_BASEADDR + 1 +#define CONFIG_SYS_NO_FLASH 1 /* no flash */ +#define CONFIG_ENV_SIZE XPAR_PERSISTENT_0_IIC_0_HIGHADDR - XPAR_PERSISTENT_0_IIC_0_BASEADDR + 1 #define CONFIG_BAUDRATE 9600 #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ @@ -85,7 +86,7 @@ "root=/dev/xsysace/disc0/part3 rw" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* @@ -116,64 +117,58 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#define CFG_DUART_CHAN 0 -#define CFG_NS16550_REG_SIZE -4 -#define CFG_NS16550 1 -#define CFG_INIT_CHAN1 1 +#define CONFIG_SYS_DUART_CHAN 0 +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550 1 +#define CONFIG_SYS_INIT_CHAN1 1 /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} -#define CFG_LOAD_ADDR 0x400000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_MONITOR_BASE 0x04000000 -#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_MONITOR_BASE 0x04000000 +#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR 0x800000 /* inside of SDRAM */ -#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR 0x800000 /* inside of SDRAM */ +#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Internal Definitions