X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fmotionpro.h;h=136db0dd260b5408fa8c077a0a26c136b329b269;hb=c9032ce168c1344fe8ffe8604825ec343ec14adf;hp=97c614b5d6f17d088c2e6aada227b6e86d765ebd;hpb=2431492aef1de33bd222c97ecc131a338d9c454e;p=u-boot

diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h
index 97c614b5d6..136db0dd26 100644
--- a/include/configs/motionpro.h
+++ b/include/configs/motionpro.h
@@ -17,7 +17,6 @@
 /* CPU and board */
 #define CONFIG_MPC5200		1	/* This is a MPC5200 CPU */
 #define CONFIG_MOTIONPRO	1	/* ... on Promess Motion-PRO board */
-#define CONFIG_DISPLAY_BOARDINFO
 
 #define CONFIG_HIGH_BATS	1	/* High BATs supported */
 
@@ -34,19 +33,11 @@
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DTT
 #define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 
 /*
@@ -54,7 +45,6 @@
  */
 #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
 #define CONFIG_NETCONSOLE	1	/* network console */
-#define CONFIG_BAUDRATE		115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 
 /*
@@ -69,14 +59,9 @@
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY	2	/* autoboot after 2 seconds */
 #undef CONFIG_BOOTARGS
 
 #define CONFIG_CMDLINE_EDITING		1	/* add command line history	*/
-#define	CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
-#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-
-#define CONFIG_VERSION_VARIABLE	1	/* include version env variable */
 
 /*
  * Default environment settings
@@ -269,7 +254,6 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0x0060
 #define CONFIG_SYS_ATA_REG_OFFSET	CONFIG_SYS_ATA_DATA_OFFSET
 #define CONFIG_SYS_ATA_STRIDE		4
-#define CONFIG_DOS_PARTITION
 
 /*
  * I2C configuration
@@ -285,7 +269,6 @@
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	1	/* 2 bytes per write cycle */
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5	/* 2ms/cycle + 3ms extra */
-#define CONFIG_SYS_I2C_MULTI_EEPROMS		1	/* 2 EEPROMs (addr:50,52) */
 
 /*
  * RTC configuration
@@ -296,24 +279,10 @@
 /*
  * Status LED configuration
  */
-#define CONFIG_STATUS_LED		/* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED
 
 #define ENABLE_GPIO_OUT		0x00000024
 #define LED_ON			0x00000010
 
-#ifndef __ASSEMBLY__
-/*
- * In case of Motion-PRO, a LED is identified by its corresponding
- * GPT Enable and Mode Select Register.
- */
-typedef volatile unsigned long * led_id_t;
-
-extern void __led_init(led_id_t id, int state);
-extern void __led_toggle(led_id_t id);
-extern void __led_set(led_id_t id, int state);
-#endif /* __ASSEMBLY__ */
-
 /*
  * Temperature sensor
  */
@@ -378,10 +347,6 @@ extern void __led_set(led_id_t id, int state);
 /* Not needed for MPC 5xxx U-Boot, but used by tools/updater */
 #define CONFIG_SYS_RESET_ADDRESS	0xfff00100
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)