X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fomap3_beagle.h;h=076dd5a8afaa5b08b81107fb0560486f0baa3274;hb=1032d97496f6d534bf0030a5779ff1cb38cc9ebf;hp=21078cf86461e9c13b3391063d6ee3a121e3d1cb;hpb=a784c01adcefe3efd4e651c5230e6117a7be35f8;p=u-boot

diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 21078cf864..076dd5a8af 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -55,6 +55,15 @@
 #undef CONFIG_USE_IRQ				/* no support for IRQs */
 #define CONFIG_MISC_INIT_R
 
+#define CONFIG_OF_LIBFDT		1
+/*
+ * The early kernel mapping on ARM currently only maps from the base of DRAM
+ * to the end of the kernel image.  The kernel is loaded at DRAM base + 0x8000.
+ * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000,
+ * so that leaves DRAM base to DRAM base + 0x4000 available.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	        0x4000
+
 #define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS	1
 #define CONFIG_INITRD_TAG		1
@@ -66,7 +75,6 @@
 #define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
 						/* Sector */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */
 
 /*
@@ -95,8 +103,9 @@
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
 					115200}
+#define CONFIG_GENERIC_MMC		1
 #define CONFIG_MMC			1
-#define CONFIG_OMAP3_MMC		1
+#define CONFIG_OMAP_HSMMC		1
 #define CONFIG_DOS_PARTITION		1
 
 /* DDR - I use Micron DDR */
@@ -111,11 +120,6 @@
 #define CONFIG_USB_DEVICE		1
 #define CONFIG_USB_TTY			1
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
-/* Change these to suit your needs */
-#define CONFIG_USBD_VENDORID		0x0451
-#define CONFIG_USBD_PRODUCTID		0x5678
-#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
-#define CONFIG_USBD_PRODUCT_NAME	"Beagle"
 
 /* commands to include */
 #include <config_cmd_default.h>
@@ -148,6 +152,7 @@
 #define CONFIG_SYS_I2C_SLAVE		1
 #define CONFIG_SYS_I2C_BUS		0
 #define CONFIG_SYS_I2C_BUS_SELECT	1
+#define CONFIG_I2C_MULTI_BUS		1
 #define CONFIG_DRIVER_OMAP34XX_I2C	1
 
 /*
@@ -189,6 +194,7 @@
 	"vram=12M\0" \
 	"dvimode=1024x768MR-16@60\0" \
 	"defaultdisplay=dvi\0" \
+	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"nandroot=/dev/mtdblock4 rw\0" \
@@ -209,10 +215,10 @@
 		"omapdss.def_disp=${defaultdisplay} " \
 		"root=${nandroot} " \
 		"rootfstype=${nandrootfstype}\0" \
-	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+	"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 	"bootscript=echo Running bootscript from mmc ...; " \
 		"source ${loadaddr}\0" \
-	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+	"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
 	"mmcboot=echo Booting from mmc ...; " \
 		"run mmcargs; " \
 		"bootm ${loadaddr}\0" \
@@ -222,7 +228,7 @@
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmc init; then " \
+	"if mmc rescan ${mmcdev}; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
@@ -340,9 +346,11 @@ extern unsigned int boot_flash_sec;
 extern unsigned int boot_flash_type;
 #endif
 
-/* additions for new relocation code, must be added to all boards */
-#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */
 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR		(LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE	0x800
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
+					 CONFIG_SYS_INIT_RAM_SIZE - \
+					 GENERATED_GBL_DATA_SIZE)
 
 #endif /* __CONFIG_H */