X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fpcm030.h;h=406f3e547ab9f381d5bcbbe09b590e7c96a4a8ab;hb=d29adf8eef4e9557326fd0bc09a08c7dfa688eab;hp=b4a7225fb8827e03b6135429f25848dccc057f6d;hpb=e6de55ec5bf306df3b3cc8e7a4cc17fa1e78ca6c;p=u-boot

diff --git a/include/configs/pcm030.h b/include/configs/pcm030.h
index b4a7225fb8..406f3e547a 100644
--- a/include/configs/pcm030.h
+++ b/include/configs/pcm030.h
@@ -44,18 +44,12 @@ Serial console configuration
 					/*define gps port conf. */
 					/* register later on to */
 					/*enable UART function! */
-#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
 
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_PCI
 
 #define	CONFIG_TIMESTAMP	1	/* Print image info with timestamp */
@@ -70,15 +64,8 @@ Serial console configuration
 #define MTDPARTS_DEFAULT   	"mtdparts=physmap-flash.0:256k(ubootl)," \
 	"1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)"
 
-/*-----------------------------------------------------------------------------
-Autobooting
------------------------------------------------------------------------------*/
-#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* allow stopping of boot process */
-					/* even with bootdelay=0 */
 #undef	CONFIG_BOOTARGS
 
-
 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \"run bootcmd_net\" to load Kernel over TFTP and to "\
 		"mount root filesystem over NFS;" \
@@ -123,8 +110,6 @@ IPB Bus clocking configuration.
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  * -----------------------------------------------------------------------*/
-#define CONFIG_PCI			1
-#define CONFIG_PCI_PNP			1
 #define CONFIG_PCI_SCAN_SHOW		1
 #define CONFIG_PCI_MEM_BUS		0x40000000
 #define CONFIG_PCI_MEM_PHYS		CONFIG_PCI_MEM_BUS
@@ -134,31 +119,6 @@ IPB Bus clocking configuration.
 #define CONFIG_PCI_IO_SIZE		0x01000000
 #define CONFIG_SYS_XLB_PIPELINING	1
 
-/*---------------------------------------------------------------------------
- I2C configuration
----------------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*---------------------------------------------------------------------------
- EEPROM CAT24WC32 configuration
----------------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52	/* 1010100x */
-#define CONFIG_SYS_I2C_FACT_ADDR	0x52	/* EEPROM CAT24WC32 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address */
-#define CONFIG_SYS_EEPROM_SIZE		2048
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
-
-/*---------------------------------------------------------------------------
-RTC configuration
----------------------------------------------------------------------------*/
-#define RTC
-#define CONFIG_RTC_PCF8563		1
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51
-
 /*---------------------------------------------------------------------------
  Flash configuration
 ---------------------------------------------------------------------------*/
@@ -186,11 +146,10 @@ RTC configuration
  Environment settings
 ---------------------------------------------------------------------------*/
 
-/* pcm030 ships with environment is EEPROM by default */
-#define CONFIG_ENV_IS_IN_EEPROM	1
+#define CONFIG_ENV_IS_NOWHERE
 #define CONFIG_ENV_OFFSET	0x00	/* environment starts at the */
 					/*beginning of the EEPROM */
-#define CONFIG_ENV_SIZE		CONFIG_SYS_EEPROM_SIZE
+#define CONFIG_ENV_SIZE		2048
 
 #define CONFIG_ENV_OVERWRITE	1
 
@@ -360,8 +319,6 @@ RTC configuration
 
 #define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
 
-#define CONFIG_DISPLAY_BOARDINFO 1
-
 /*-----------------------------------------------------------------------------
  Various low-level settings
 -----------------------------------------------------------------------------*/
@@ -410,12 +367,8 @@ RTC configuration
 #define CONFIG_SYS_ATA_STRIDE		4
 #define CONFIG_ATAPI			1
 
-/* we enable IDE and FAT support, so we also need partition support */
-#define CONFIG_DOS_PARTITION 1
-
 /* USB */
 #define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
 
 /* pass open firmware flat tree */
 #define OF_CPU				"PowerPC,5200@0"