X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fpf5200.h;h=4a985456d9b5feb60c48c5a48ca5277489224a40;hb=0a7bec7f991950da90c6ee6bc59f322abebccbb7;hp=8ca55d78ecc58899dfab06aa3deeda4705c89d21;hpb=ea393eb1d6a786fc2e895f90abb5f7e7541aef45;p=u-boot

diff --git a/include/configs/pf5200.h b/include/configs/pf5200.h
index 8ca55d78ec..4a985456d9 100644
--- a/include/configs/pf5200.h
+++ b/include/configs/pf5200.h
@@ -44,10 +44,11 @@
 #define CONFIG_PF5200		1	/* ... on PF5200  board */
 #define CONFIG_MPC5200_DDR	1	/* ... use DDR RAM	*/
 
-#define CONFIG_SYS_MPC5XXX_CLKIN	33000000	/* ... running at 33.000000MHz */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xFFF00000
+#endif
 
-#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH  */
-#define BOOTFLAG_WARM		0x02	/* Software reboot	     */
+#define CONFIG_SYS_MPC5XXX_CLKIN	33000000	/* ... running at 33.000000MHz */
 
 #define CONFIG_HIGH_BATS	1	/* High BATs supported */
 /*
@@ -61,7 +62,6 @@
 #endif
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 
-#ifdef CONFIG_MPC5200		/* MPC5100 PCI is not supported yet. */
 /*
  * PCI Mapping:
  * 0x40000000 - 0x4fffffff - PCI Memory
@@ -82,12 +82,10 @@
 
 #define CONFIG_MII		1
 #if 0				/* test-only !!! */
-#define CONFIG_NET_MULTI	1
 #define CONFIG_EEPRO100		1
 #define CONFIG_SYS_RX_ETH_BUFFER	8	/* use 8 rx buffer on eepro100	*/
 #define CONFIG_NS8382X		1
 #endif
-#endif
 
 /* Partitions */
 #define CONFIG_MAC_PARTITION
@@ -121,16 +119,14 @@
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IDE
 
-#ifdef CONFIG_MPC5200
 #define CONFIG_CMD_PCI
-#endif
 
 
-#if (TEXT_BASE == 0xFF000000)	/* Boot low with 16 MB Flash */
+#if (CONFIG_SYS_TEXT_BASE == 0xFF000000)	/* Boot low with 16 MB Flash */
 #   define CONFIG_SYS_LOWBOOT		1
 #   define CONFIG_SYS_LOWBOOT16	1
 #endif
-#if (TEXT_BASE == 0xFF800000)	/* Boot low with  8 MB Flash */
+#if (CONFIG_SYS_TEXT_BASE == 0xFF800000)	/* Boot low with  8 MB Flash */
 #   define CONFIG_SYS_LOWBOOT		1
 #   define CONFIG_SYS_LOWBOOT08	1
 #endif
@@ -166,12 +162,10 @@
 
 #define CONFIG_BOOTCOMMAND	"run flash_vxworks0"
 
-#if defined(CONFIG_MPC5200)
 /*
  * IPB Bus clocking configuration.
  */
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
-#endif
 /*
  * I2C configuration
  */
@@ -226,13 +220,12 @@
 
 /* Use SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_END	MPC5XXX_SRAM_SIZE	/* End of used area in DPRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE	/* Size of used area in DPRAM */
 
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_BASE    TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT		1
 #endif
@@ -289,13 +282,8 @@
 /*
  * Various low-level settings
  */
-#if defined(CONFIG_MPC5200)
 #define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL		HID0_ICE
-#else
-#define CONFIG_SYS_HID0_INIT		0
-#define CONFIG_SYS_HID0_FINAL		0
-#endif
 
 #define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE