X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fsbc405.h;h=5abcda3c36550323ce13854317170ab26cd013a1;hb=f3fcf92d595b297b47a1b58b8ec39f93f40ef912;hp=d93ca2d98f2adaece7c8d70831ef7f8eb3e01893;hpb=6d0f6bcf337c5261c08fabe12982178c2c489d76;p=u-boot

diff --git a/include/configs/sbc405.h b/include/configs/sbc405.h
index d93ca2d98f..5abcda3c36 100644
--- a/include/configs/sbc405.h
+++ b/include/configs/sbc405.h
@@ -36,6 +36,8 @@
 #define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_SBC405		1	/* ...on a WR SBC405 board	*/
 
+#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
 
@@ -58,6 +60,7 @@
 #define CONFIG_BOOTCOMMAND      "version;echo;tftpboot ${loadaddr} ${loadfile};bootvx"      /* autoboot command     */
 
 
+#define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_PHY_RESET_DELAY	300	/* Intel LXT971A needs this	*/
@@ -129,9 +132,6 @@
 #define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 
 #undef CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-#endif
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
@@ -145,8 +145,13 @@
 #define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
+#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
+
 #undef CONFIG_SYS_EXT_SERIAL_CLOCK		/* no external serial clock used */
-#define CONFIG_SYS_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
 #define CONFIG_SYS_BASE_BAUD		691200
 
 /* The following table includes the supported baudrates */
@@ -165,6 +170,7 @@
 
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
 #undef  CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
@@ -254,9 +260,8 @@
 #define CONFIG_SYS_OCM_DATA_SIZE	0x1000
 
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM	*/
-#define CONFIG_SYS_GBL_DATA_SIZE	128  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -266,12 +271,4 @@
 #define SPD_EEPROM_ADDRESS	0x50
 #define CONFIG_SPD_EEPROM	1	/* use SPD EEPROM for setup		*/
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
 #endif	/* __CONFIG_H */