X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fsbc8548.h;h=ec9ad4556785a8561d45dddc89d267076d2caee3;hb=9f03247edc7761b608db31104821b4518a70e691;hp=3aae95e345099d40ab898127337462dc7787978b;hpb=1a4596601fd395f3afb8f82f3f840c5e00bdd57a;p=u-boot

diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index 3aae95e345..ec9ad45567 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -38,7 +38,6 @@
  */
 #define CONFIG_BOOKE		1	/* BOOKE */
 #define CONFIG_E500		1	/* BOOKE e500 family */
-#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
 #define CONFIG_MPC8548		1	/* MPC8548 specific */
 #define CONFIG_SBC8548		1	/* SBC8548 board specific */
 
@@ -102,7 +101,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #undef CONFIG_DDR_ECC			/* only for ECC DDR module */
 /*
@@ -406,7 +405,6 @@
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX	1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		(400000000 / CONFIG_SYS_CLK_DIV)
@@ -417,24 +415,15 @@
 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
 /*
  * I2C
  */
-#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#define CONFIG_SYS_I2C_OFFSET		0x3000
 
 /*
  * General PCI
@@ -482,7 +471,6 @@
 
 #endif	/* CONFIG_PCI */
 
-
 #if defined(CONFIG_TSEC_ENET)
 
 #define CONFIG_MII		1	/* MII PHY management */
@@ -532,23 +520,15 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
 #endif
 
-
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
 /*
@@ -558,7 +538,6 @@
 #define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
@@ -567,7 +546,6 @@
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
@@ -578,19 +556,14 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 
 /*
  * Environment Configuration
  */
-
-/* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR	 02:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR	 02:E0:0C:00:01:FD
 #endif
 
 #define CONFIG_IPADDR	 192.168.0.55
@@ -606,7 +579,6 @@
 
 #define CONFIG_LOADADDR	1000000	/*default location for tftp and bootm*/
 
-#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
 #undef	CONFIG_BOOTARGS		/* the boot command will set bootargs*/
 
 #define CONFIG_BAUDRATE	115200
@@ -623,7 +595,7 @@
 "consoledev=ttyS0\0"				\
 "ramdiskaddr=2000000\0"			\
 "ramdiskfile=uRamdisk\0"			\
-"fdtaddr=c00000\0"				\
+"fdtaddr=1e00000\0"				\
 "fdtfile=sbc8548.dtb\0"
 
 #define CONFIG_NFSBOOTCOMMAND						\
@@ -635,7 +607,6 @@
    "tftp $fdtaddr $fdtfile;"						\
    "bootm $loadaddr - $fdtaddr"
 
-
 #define CONFIG_RAMBOOTCOMMAND \
    "setenv bootargs root=/dev/ram rw "					\
       "console=$consoledev,$baudrate $othbootargs;"			\