X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fsbc8560.h;h=95c68bce3cbde94206602dce5ce5d0c858ca256e;hb=928c4bdf9b069be218436d25b96721395c4d671f;hp=a75e4be2126fd436f2f2e421f5ed8f8b787a7ae4;hpb=d48455ad8cefd25d7b49f68fd16d0e9fd551732a;p=u-boot

diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index a75e4be212..95c68bce3c 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -92,20 +92,6 @@
 #error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
 #endif
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default	*/
-
-#if XXX
-  #define CONFIG_SYS_CCSRBAR		0xfdf00000	/* relocated CCSRBAR	*/
-#else
-  #define CONFIG_SYS_CCSRBAR		0xff700000	/* default CCSRBAR	*/
-#endif
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR	*/
-
 #define CONFIG_SYS_SDRAM_SIZE		512		/* DDR is 512MB */
 
 /* DDR Setup */
@@ -116,7 +102,7 @@
 #undef  CONFIG_DDR_SPD
 
 #if defined(CONFIG_MPC85xx_REV1)
-  #define CONFIG_DDR_DLL			/* possible DLL fix needed	*/
+#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN	/* possible DLL fix needed */
 #endif
 
 #undef  CONFIG_DDR_ECC			    /* only for ECC DDR module */
@@ -191,10 +177,9 @@
 
 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR	0x70000000	/* Initial RAM address	*/
-#define CONFIG_SYS_INIT_RAM_END	0x4000		/* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_SIZE	128		/* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
@@ -245,10 +230,6 @@
 
 #ifdef CONFIG_TSEC_ENET
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 	1
-#endif
-
 #ifndef CONFIG_MII
 #define CONFIG_MII		1	/* MII PHY management */
 #endif
@@ -279,8 +260,8 @@
      * - Select bus for bd/buffers
      * - Full duplex
      */
-    #define CONFIG_SYS_CMXFCR_MASK	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-    #define CONFIG_SYS_CMXFCR_VALUE	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+    #define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+    #define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
     #define CONFIG_SYS_CPMFCR_RAMTYPE	0
     #define CONFIG_SYS_FCC_PSMR	(FCC_PSMR_FDE)
 
@@ -424,14 +405,6 @@
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02		/* Software reboot		*/
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
@@ -455,8 +428,8 @@
  */
 
 #define CONFIG_HOSTNAME		SBC8560
-#define CONFIG_ROOTPATH		/home/ppc
-#define CONFIG_BOOTFILE		uImage
+#define CONFIG_ROOTPATH		"/home/ppc"
+#define CONFIG_BOOTFILE		"uImage"
 
 #define	CONFIG_EXTRA_ENV_SETTINGS		\
 	"netdev=eth0\0"				\