X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fsbc8641d.h;h=248785db381ab7b46702376510c3d91a8fb1f522;hb=fc5d54b7fa3fa602e06e2f0863c0b134d6afca70;hp=a489bb12118968526cfdc0c08c41e4578c7f5ede;hpb=9cc18042e61275210cf888e5759347eeb2a2e297;p=u-boot

diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
index a489bb1211..248785db38 100644
--- a/include/configs/sbc8641d.h
+++ b/include/configs/sbc8641d.h
@@ -14,14 +14,13 @@
  * SBC8641D board configuration file
  *
  * Make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
+ * search for CONFIG_SERVERIP, etc in this file.
  */
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
 /* High Level Configuration Options */
-#define CONFIG_MPC86xx		1	/* MPC86xx */
 #define CONFIG_MPC8641		1	/* MPC8641 specific */
 #define CONFIG_SBC8641D		1	/* SBC8641D board specific */
 #define CONFIG_MP		1	/* support multiple processors */
@@ -45,8 +44,8 @@
 #define CONFIG_SRIO1			/* SRIO port 1 */
 
 #define CONFIG_PCI		1	/* Enable PCIE */
-#define CONFIG_PCIE1		1	/* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2		1	/* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE1		1	/* PCIE controller 1 (slot 1) */
+#define CONFIG_PCIE2		1	/* PCIE controller 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
@@ -67,7 +66,6 @@
 #define BANK_INTERLEAVING		0x22000000
 #define SUPER_BANK_INTERLEAVING		0x23000000
 
-
 #define CONFIG_ALTIVEC          1
 
 /*
@@ -173,7 +171,6 @@
     #define CONFIG_SYS_DDR2_CLK_CTRL	0x03800000
     #define CONFIG_SYS_DDR2_CFG_1B	0xC3008008
 
-
 #endif
 
 /* #define CONFIG_ID_EEPROM	1
@@ -242,12 +239,11 @@
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)    /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)    /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN		(384 * 1024)    /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)   /* Reserved for malloc */
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX     1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
@@ -258,18 +254,6 @@
 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/*
- * Pass open firmware flat tree to kernel
- */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
 /*
  * I2C
  */
@@ -313,8 +297,6 @@
 
 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 
-#undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE
-
 #define CONFIG_PCI_PNP			/* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
@@ -473,17 +455,14 @@
  * Environment
  */
 #define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x40000)
-#define CONFIG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128k(one sector) for env */
 #define CONFIG_ENV_SIZE		0x2000
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
-#include <config_cmd_default.h>
-    #define CONFIG_CMD_PING
-    #define CONFIG_CMD_I2C
-    #define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
@@ -496,7 +475,7 @@
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_CMDLINE_EDITING	1		/* add command line history */
 
 #if defined(CONFIG_CMD_KGDB)
     #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
@@ -507,7 +486,6 @@
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
@@ -525,21 +503,12 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 
 /*
  * Environment Configuration
  */
 
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_ETHADDR   02:E0:0C:00:00:01
-#define CONFIG_ETH1ADDR  02:E0:0C:00:01:FD
-#define CONFIG_ETH2ADDR  02:E0:0C:00:02:FD
-#define CONFIG_ETH3ADDR  02:E0:0C:00:03:FD
-#endif
-
 #define CONFIG_HAS_ETH0		1
 #define CONFIG_HAS_ETH1		1
 #define CONFIG_HAS_ETH2		1
@@ -558,7 +527,6 @@
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR		1000000
 
-#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
 
 #define CONFIG_BAUDRATE	115200