X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2Fstxgp3.h;h=fc3881d22babd44f3cac1ebe2e868f32b60639fc;hb=374a235d42fa63cc84dbf384944a69b2d05bdc81;hp=ae6f45aeecde44f4febaf438ee6c69ee07cd8005;hpb=ba490b7761c62b549c222a9723e532dc801a3899;p=u-boot

diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index ae6f45aeec..fc3881d22b 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -43,6 +43,8 @@
 #define CONFIG_STXGP3		1	/* Silicon Tx GPPP board specific*/
 #define CONFIG_MPC8560		1
 
+#define	CONFIG_SYS_TEXT_BASE	0xfff80000
+
 #undef  CONFIG_PCI			/* pci ethernet support	*/
 #define CONFIG_TSEC_ENET		/* tsec ethernet support*/
 #undef  CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
@@ -66,6 +68,7 @@
 #define  CONFIG_BTB                          /* toggle branch predition */
 
 #define CONFIG_BOARD_EARLY_INIT_F   1        /* Call board_pre_init      */
+#define CONFIG_RESET_PHY_R	1	/* Call reset_phy()		*/
 
 #undef  CONFIG_SYS_DRAM_TEST                       /* memory test, takes time  */
 #define CONFIG_SYS_MEMTEST_START       0x00200000  /* memtest region */
@@ -96,7 +99,7 @@
 #define CONFIG_SYS_OR1_PRELIM		0xffff0ff7      /* 64K is enough */
 #define CONFIG_SYS_LBC_LCLDEVS_BASE	0xfc000000	/* Base of localbus devices */
 
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor	*/
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor	*/
 
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
@@ -120,7 +123,7 @@
 #undef CONFIG_FSL_DDR_INTERACTIVE
 
 #undef  CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_DDR_DLL                  /* possible DLL fix needed */
+#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN	/* possible DLL fix needed */
 #define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
 #define CONFIG_MEM_INIT_VALUE		0xDeadBeef
@@ -152,10 +155,9 @@
 
 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR       0x60000000      /* Initial RAM address  */
-#define CONFIG_SYS_INIT_RAM_END	0x4000		/* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_SIZE	128		/* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN		(256 * 1024)    /* Reserve 256 kB for Mon */
@@ -320,9 +322,10 @@
 
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
+#define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_SAVEENV
     #undef CONFIG_CMD_LOADS
 #else
     #define CONFIG_CMD_ELF
@@ -362,14 +365,6 @@
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02		/* Software reboot		*/
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */