X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fi2c.h;h=695cb7655f535c7a60cd4102361ae215a43339d6;hb=6d29cc7dcf2d35966aa0b6119fd1cbca0d21d5e6;hp=a5498a327a51ae5e68958d782cd7885c3aea9e5e;hpb=7d7db2225c5e63a389ee04d63919f012e7ba880d;p=u-boot diff --git a/include/i2c.h b/include/i2c.h index a5498a327a..695cb7655f 100644 --- a/include/i2c.h +++ b/include/i2c.h @@ -74,6 +74,49 @@ struct dm_i2c_bus { int speed_hz; }; +/* + * Not all of these flags are implemented in the U-Boot API + */ +enum dm_i2c_msg_flags { + I2C_M_TEN = 0x0010, /* ten-bit chip address */ + I2C_M_RD = 0x0001, /* read data, from slave to master */ + I2C_M_STOP = 0x8000, /* send stop after this message */ + I2C_M_NOSTART = 0x4000, /* no start before this message */ + I2C_M_REV_DIR_ADDR = 0x2000, /* invert polarity of R/W bit */ + I2C_M_IGNORE_NAK = 0x1000, /* continue after NAK */ + I2C_M_NO_RD_ACK = 0x0800, /* skip the Ack bit on reads */ + I2C_M_RECV_LEN = 0x0400, /* length is first received byte */ +}; + +/** + * struct i2c_msg - an I2C message + * + * @addr: Slave address + * @flags: Flags (see enum dm_i2c_msg_flags) + * @len: Length of buffer in bytes, may be 0 for a probe + * @buf: Buffer to send/receive, or NULL if no data + */ +struct i2c_msg { + uint addr; + uint flags; + uint len; + u8 *buf; +}; + +/** + * struct i2c_msg_list - a list of I2C messages + * + * This is called i2c_rdwr_ioctl_data in Linux but the name does not seem + * appropriate in U-Boot. + * + * @msg: Pointer to i2c_msg array + * @nmsgs: Number of elements in the array + */ +struct i2c_msg_list { + struct i2c_msg *msgs; + uint nmsgs; +}; + /** * dm_i2c_read() - read bytes from an I2C chip * @@ -129,6 +172,7 @@ int dm_i2c_probe(struct udevice *bus, uint chip_addr, uint chip_flags, * * This reads a single value from the given address in an I2C chip * + * @dev: Device to use for transfer * @addr: Address to read from * @return value read, or -ve on error */ @@ -139,12 +183,26 @@ int dm_i2c_reg_read(struct udevice *dev, uint offset); * * This writes a single value to the given address in an I2C chip * + * @dev: Device to use for transfer * @addr: Address to write to * @val: Value to write (normally a byte) * @return 0 on success, -ve on error */ int dm_i2c_reg_write(struct udevice *dev, uint offset, unsigned int val); +/** + * dm_i2c_xfer() - Transfer messages over I2C + * + * This transfers a raw message. It is best to use dm_i2c_reg_read/write() + * instead. + * + * @dev: Device to use for transfer + * @msg: List of messages to transfer + * @nmsgs: Number of messages to transfer + * @return 0 on success, -ve on error + */ +int dm_i2c_xfer(struct udevice *dev, struct i2c_msg *msg, int nmsgs); + /** * dm_i2c_set_bus_speed() - set the speed of a bus * @@ -292,49 +350,6 @@ void i2c_reg_write(uint8_t addr, uint8_t reg, uint8_t val); #endif -/* - * Not all of these flags are implemented in the U-Boot API - */ -enum dm_i2c_msg_flags { - I2C_M_TEN = 0x0010, /* ten-bit chip address */ - I2C_M_RD = 0x0001, /* read data, from slave to master */ - I2C_M_STOP = 0x8000, /* send stop after this message */ - I2C_M_NOSTART = 0x4000, /* no start before this message */ - I2C_M_REV_DIR_ADDR = 0x2000, /* invert polarity of R/W bit */ - I2C_M_IGNORE_NAK = 0x1000, /* continue after NAK */ - I2C_M_NO_RD_ACK = 0x0800, /* skip the Ack bit on reads */ - I2C_M_RECV_LEN = 0x0400, /* length is first received byte */ -}; - -/** - * struct i2c_msg - an I2C message - * - * @addr: Slave address - * @flags: Flags (see enum dm_i2c_msg_flags) - * @len: Length of buffer in bytes, may be 0 for a probe - * @buf: Buffer to send/receive, or NULL if no data - */ -struct i2c_msg { - uint addr; - uint flags; - uint len; - u8 *buf; -}; - -/** - * struct i2c_msg_list - a list of I2C messages - * - * This is called i2c_rdwr_ioctl_data in Linux but the name does not seem - * appropriate in U-Boot. - * - * @msg: Pointer to i2c_msg array - * @nmsgs: Number of elements in the array - */ -struct i2c_msg_list { - struct i2c_msg *msgs; - uint nmsgs; -}; - /** * struct dm_i2c_ops - driver operations for I2C uclass * @@ -429,6 +444,45 @@ struct dm_i2c_ops { #define i2c_get_ops(dev) ((struct dm_i2c_ops *)(dev)->driver->ops) +/** + * struct i2c_mux_ops - operations for an I2C mux + * + * The current mux state is expected to be stored in the mux itself since + * it is the only thing that knows how to make things work. The mux can + * record the current state and then avoid switching unless it is necessary. + * So select() can be skipped if the mux is already in the correct state. + * Also deselect() can be made a nop if required. + */ +struct i2c_mux_ops { + /** + * select() - select one of of I2C buses attached to a mux + * + * This will be called when there is no bus currently selected by the + * mux. This method does not need to deselect the old bus since + * deselect() will be already have been called if necessary. + * + * @mux: Mux device + * @bus: I2C bus to select + * @channel: Channel number correponding to the bus to select + * @return 0 if OK, -ve on error + */ + int (*select)(struct udevice *mux, struct udevice *bus, uint channel); + + /** + * deselect() - select one of of I2C buses attached to a mux + * + * This is used to deselect the currently selected I2C bus. + * + * @mux: Mux device + * @bus: I2C bus to deselect + * @channel: Channel number correponding to the bus to deselect + * @return 0 if OK, -ve on error + */ + int (*deselect)(struct udevice *mux, struct udevice *bus, uint channel); +}; + +#define i2c_mux_get_ops(dev) ((struct i2c_mux_ops *)(dev)->driver->ops) + /** * i2c_get_chip() - get a device to use to access a chip on a bus * @@ -445,7 +499,8 @@ int i2c_get_chip(struct udevice *bus, uint chip_addr, uint offset_len, struct udevice **devp); /** - * i2c_get_chip() - get a device to use to access a chip on a bus number + * i2c_get_chip_for_busnum() - get a device to use to access a chip on + * a bus number * * This returns the device for the given chip address on a particular bus * number. @@ -470,8 +525,7 @@ int i2c_get_chip_for_busnum(int busnum, int chip_addr, uint offset_len, * @node: Node offset to read from * @spi: Place to put the decoded information */ -int i2c_chip_ofdata_to_platdata(const void *blob, int node, - struct dm_i2c_chip *chip); +int i2c_chip_ofdata_to_platdata(struct udevice *dev, struct dm_i2c_chip *chip); /** * i2c_dump_msgs() - Dump a list of I2C messages @@ -516,9 +570,6 @@ void i2c_dump_msgs(struct i2c_msg *msg, int nmsgs); #if !defined(CONFIG_SYS_RTC_BUS_NUM) #define CONFIG_SYS_RTC_BUS_NUM 0 #endif -#if !defined(CONFIG_SYS_DTT_BUS_NUM) -#define CONFIG_SYS_DTT_BUS_NUM 0 -#endif #if !defined(CONFIG_SYS_SPD_BUS_NUM) #define CONFIG_SYS_SPD_BUS_NUM 0 #endif @@ -609,12 +660,7 @@ extern struct i2c_bus_hose i2c_bus[]; #endif #ifndef I2C_SOFT_DECLARATIONS -# if defined(CONFIG_MPC8260) -# define I2C_SOFT_DECLARATIONS volatile ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT); -# elif defined(CONFIG_8xx) -# define I2C_SOFT_DECLARATIONS volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; - -# elif (defined(CONFIG_AT91RM9200) || \ +# if (defined(CONFIG_AT91RM9200) || \ defined(CONFIG_AT91SAM9260) || defined(CONFIG_AT91SAM9261) || \ defined(CONFIG_AT91SAM9263)) # define I2C_SOFT_DECLARATIONS at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIOA; @@ -623,15 +669,6 @@ extern struct i2c_bus_hose i2c_bus[]; # endif #endif -#ifdef CONFIG_8xx -/* Set default value for the I2C bus speed on 8xx. In the - * future, we'll define these in all 8xx board config files. - */ -#ifndef CONFIG_SYS_I2C_SPEED -#define CONFIG_SYS_I2C_SPEED 50000 -#endif -#endif - /* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real @@ -646,11 +683,11 @@ extern struct i2c_bus_hose i2c_bus[]; * Initialization, must be called once on start up, may be called * repeatedly to change the speed and slave addresses. */ +#ifdef CONFIG_SYS_I2C_EARLY_INIT +void i2c_early_init_f(void); +#endif void i2c_init(int speed, int slaveaddr); void i2c_init_board(void); -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT -void i2c_board_late_init(void); -#endif #ifdef CONFIG_SYS_I2C /* @@ -733,21 +770,6 @@ unsigned int i2c_set_bus_speed(unsigned int speed); unsigned int i2c_get_bus_speed(void); -/* - * i2c_reloc_fixup: - * - * Adjusts I2C pointers after U-Boot is relocated to DRAM - */ -void i2c_reloc_fixup(void); -#if defined(CONFIG_SYS_I2C_SOFT) -void i2c_soft_init(void); -void i2c_soft_active(void); -void i2c_soft_tristate(void); -int i2c_soft_read(void); -void i2c_soft_sda(int bit); -void i2c_soft_scl(int bit); -void i2c_soft_delay(void); -#endif #else /* @@ -778,11 +800,6 @@ static inline u8 i2c_reg_read(u8 addr, u8 reg) { u8 buf; -#ifdef CONFIG_8xx - /* MPC8xx needs this. Maybe one day we can get rid of it. */ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); -#endif - #ifdef DEBUG printf("%s: addr=0x%02x, reg=0x%02x\n", __func__, addr, reg); #endif @@ -794,11 +811,6 @@ static inline u8 i2c_reg_read(u8 addr, u8 reg) static inline void i2c_reg_write(u8 addr, u8 reg, u8 val) { -#ifdef CONFIG_8xx - /* MPC8xx needs this. Maybe one day we can get rid of it. */ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); -#endif - #ifdef DEBUG printf("%s: addr=0x%02x, reg=0x%02x, val=0x%02x\n", __func__, addr, reg, val); @@ -887,13 +899,6 @@ enum { I2C_8, I2C_9, I2C_10, }; -/* Multi I2C busses handling */ -#ifdef CONFIG_SOFT_I2C_MULTI_BUS -extern int get_multi_scl_pin(void); -extern int get_multi_sda_pin(void); -extern int multi_i2c_init(void); -#endif - /** * Get FDT values for i2c bus. *