X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fi2c.h;h=9300d97e146b03f406b1b5ea505be2d5886d9325;hb=aa5a0d98943e1b32109fd1fb325007c6cdcedc50;hp=27fe00f17361763a42bc13f59e378d464c484dc6;hpb=6a608f20b987122a658e26978d76d2753654f5f2;p=u-boot

diff --git a/include/i2c.h b/include/i2c.h
index 27fe00f173..9300d97e14 100644
--- a/include/i2c.h
+++ b/include/i2c.h
@@ -25,14 +25,13 @@
  * enough as to be incompatible for compilation purposes.
  */
 
-#ifdef CONFIG_DM_I2C
-
 enum dm_i2c_chip_flags {
 	DM_I2C_CHIP_10BIT	= 1 << 0, /* Use 10-bit addressing */
 	DM_I2C_CHIP_RD_ADDRESS	= 1 << 1, /* Send address for each read byte */
 	DM_I2C_CHIP_WR_ADDRESS	= 1 << 2, /* Send address for each write byte */
 };
 
+struct udevice;
 /**
  * struct dm_i2c_chip - information about an i2c chip
  *
@@ -55,6 +54,7 @@ struct dm_i2c_chip {
 	uint flags;
 #ifdef CONFIG_SANDBOX
 	struct udevice *emul;
+	bool test_mode;
 #endif
 };
 
@@ -65,8 +65,8 @@ struct dm_i2c_chip {
  * bus can operate at different speeds (measured in Hz, typically 100KHz
  * or 400KHz).
  *
- * To obtain this structure, use bus->uclass_priv where bus is the I2C
- * bus udevice.
+ * To obtain this structure, use dev_get_uclass_priv(bus) where bus is the
+ * I2C bus udevice.
  *
  * @speed_hz: Bus speed in hertz (typically 100000)
  */
@@ -125,21 +125,42 @@ int dm_i2c_probe(struct udevice *bus, uint chip_addr, uint chip_flags,
 		 struct udevice **devp);
 
 /**
- * i2c_set_bus_speed() - set the speed of a bus
+ * dm_i2c_reg_read() - Read a value from an I2C register
+ *
+ * This reads a single value from the given address in an I2C chip
+ *
+ * @addr:	Address to read from
+ * @return value read, or -ve on error
+ */
+int dm_i2c_reg_read(struct udevice *dev, uint offset);
+
+/**
+ * dm_i2c_reg_write() - Write a value to an I2C register
+ *
+ * This writes a single value to the given address in an I2C chip
+ *
+ * @addr:	Address to write to
+ * @val:	Value to write (normally a byte)
+ * @return 0 on success, -ve on error
+ */
+int dm_i2c_reg_write(struct udevice *dev, uint offset, unsigned int val);
+
+/**
+ * dm_i2c_set_bus_speed() - set the speed of a bus
  *
  * @bus:	Bus to adjust
  * @speed:	Requested speed in Hz
  * @return 0 if OK, -EINVAL for invalid values
  */
-int i2c_set_bus_speed(struct udevice *bus, unsigned int speed);
+int dm_i2c_set_bus_speed(struct udevice *bus, unsigned int speed);
 
 /**
- * i2c_get_bus_speed() - get the speed of a bus
+ * dm_i2c_get_bus_speed() - get the speed of a bus
  *
  * @bus:	Bus to check
  * @return speed of selected I2C bus in Hz, -ve on error
  */
-int i2c_get_bus_speed(struct udevice *bus);
+int dm_i2c_get_bus_speed(struct udevice *bus);
 
 /**
  * i2c_set_chip_flags() - set flags for a chip
@@ -172,8 +193,15 @@ int i2c_get_chip_flags(struct udevice *dev, uint *flagsp);
  *
  * @offset_len:	New offset length value (typically 1 or 2)
  */
-
 int i2c_set_chip_offset_len(struct udevice *dev, uint offset_len);
+
+/**
+ * i2c_get_offset_len() - get the offset length for a chip
+ *
+ * @return:	Current offset length value (typically 1 or 2)
+ */
+int i2c_get_chip_offset_len(struct udevice *dev);
+
 /**
  * i2c_deblock() - recover a bus that is in an unknown state
  *
@@ -256,6 +284,12 @@ void i2c_init(int speed, int slaveaddr);
  */
 void board_i2c_init(const void *blob);
 
+/*
+ * Compatibility functions for driver model.
+ */
+uint8_t i2c_reg_read(uint8_t addr, uint8_t reg);
+void i2c_reg_write(uint8_t addr, uint8_t reg, uint8_t val);
+
 #endif
 
 /*
@@ -341,7 +375,7 @@ struct dm_i2c_ops {
 	 * The bus speed value will be updated by the uclass if this function
 	 * does not return an error. This method is optional - if it is not
 	 * provided then the driver can read the speed from
-	 * bus->uclass_priv->speed_hz
+	 * dev_get_uclass_priv(bus)->speed_hz
 	 *
 	 * @bus:	Bus to adjust
 	 * @speed:	Requested speed in Hz
@@ -355,7 +389,7 @@ struct dm_i2c_ops {
 	 * Normally this can be provided by the uclass, but if you want your
 	 * driver to check the bus speed by looking at the hardware, you can
 	 * implement that here. This method is optional. This method would
-	 * normally be expected to return bus->uclass_priv->speed_hz.
+	 * normally be expected to return dev_get_uclass_priv(bus)->speed_hz.
 	 *
 	 * @bus:	Bus to check
 	 * @return speed of selected I2C bus in Hz, -ve on error
@@ -439,8 +473,6 @@ int i2c_get_chip_for_busnum(int busnum, int chip_addr, uint offset_len,
 int i2c_chip_ofdata_to_platdata(const void *blob, int node,
 				struct dm_i2c_chip *chip);
 
-#endif
-
 #ifndef CONFIG_DM_I2C
 
 /*