X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fspi.h;h=9754c53aa1486910dbf5aeb329b1808a57e0e360;hb=HEAD;hp=4c179838eefcaa8f5ee44f542e52a1e219ae504d;hpb=231af7f95a4e96debeb380bd904ebee60f0bd7bf;p=u-boot

diff --git a/include/spi.h b/include/spi.h
index 4c179838ee..9754c53aa1 100644
--- a/include/spi.h
+++ b/include/spi.h
@@ -1,10 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Common SPI Interface: Controller-specific definitions
  *
  * (C) Copyright 2001
  * Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #ifndef _SPI_H_
@@ -30,10 +29,6 @@
 #define SPI_RX_DUAL	BIT(12)			/* receive with 2 wires */
 #define SPI_RX_QUAD	BIT(13)			/* receive with 4 wires */
 
-/* SPI bus connection options - see enum spi_dual_flash */
-#define SPI_CONN_DUAL_SHARED		(1 << 0)
-#define SPI_CONN_DUAL_SEPARATED	(1 << 1)
-
 /* Header byte that marks the start of the message */
 #define SPI_PREAMBLE_END_BYTE	0xec
 
@@ -90,10 +85,11 @@ struct dm_spi_slave_platdata {
  * @cs:			ID of the chip select connected to the slave.
  * @mode:		SPI mode to use for this slave (see SPI mode flags)
  * @wordlen:		Size of SPI word in number of bits
+ * @max_read_size:	If non-zero, the maximum number of bytes which can
+ *			be read at once.
  * @max_write_size:	If non-zero, the maximum number of bytes which can
- *			be written at once, excluding command bytes.
+ *			be written at once.
  * @memory_map:		Address of read-only SPI flash access.
- * @option:		Varies SPI bus options - separate, shared bus.
  * @flags:		Indication of SPI flags.
  */
 struct spi_slave {
@@ -107,9 +103,9 @@ struct spi_slave {
 #endif
 	uint mode;
 	unsigned int wordlen;
+	unsigned int max_read_size;
 	unsigned int max_write_size;
 	void *memory_map;
-	u8 option;
 
 	u8 flags;
 #define SPI_XFER_BEGIN		BIT(0)	/* Assert CS before transfer */
@@ -117,7 +113,6 @@ struct spi_slave {
 #define SPI_XFER_ONCE		(SPI_XFER_BEGIN | SPI_XFER_END)
 #define SPI_XFER_MMAP		BIT(2)	/* Memory Mapped start */
 #define SPI_XFER_MMAP_END	BIT(3)	/* Memory Mapped End */
-#define SPI_XFER_U_PAGE		BIT(4)
 };
 
 /**
@@ -321,33 +316,6 @@ static inline int spi_w8r8(struct spi_slave *slave, unsigned char byte)
 	return ret < 0 ? ret : din[1];
 }
 
-/**
- * Set up a SPI slave for a particular device tree node
- *
- * This calls spi_setup_slave() with the correct bus number. Call
- * spi_free_slave() to free it later.
- *
- * @param blob:		Device tree blob
- * @param slave_node:	Slave node to use
- * @param spi_node:	SPI peripheral node to use
- * @return pointer to new spi_slave structure
- */
-struct spi_slave *spi_setup_slave_fdt(const void *blob, int slave_node,
-				      int spi_node);
-
-/**
- * spi_base_setup_slave_fdt() - helper function to set up a SPI slace
- *
- * This decodes SPI properties from the slave node to determine the
- * chip select and SPI parameters.
- *
- * @blob:	Device tree blob
- * @busnum:	Bus number to use
- * @node:	Device tree node for the SPI bus
- */
-struct spi_slave *spi_base_setup_slave_fdt(const void *blob, int busnum,
-					   int node);
-
 #ifdef CONFIG_DM_SPI
 
 /**
@@ -568,7 +536,7 @@ int spi_find_chip_select(struct udevice *bus, int cs, struct udevice **devp);
  * @node:	Node offset to read from
  * @plat:	Place to put the decoded information
  */
-int spi_slave_ofdata_to_platdata(const void *blob, int node,
+int spi_slave_ofdata_to_platdata(struct udevice *dev,
 				 struct dm_spi_slave_platdata *plat);
 
 /**