AT91R40008/Ethernut 3 configuration

Moved board specific settings from target/at91r40008.cfg to a new
file board/ethernut3.cfg.

Set correct CPUTAPID.  Reset delay increased, see MIC2775 data sheet.
Increased work area size from 16k to 128k.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

diff --git a/tcl/board/ethernut3.cfg b/tcl/board/ethernut3.cfg
new file mode 100644 (file)
index 0000000..f22e688
--- /dev/null
+++ b/tcl/board/ethernut3.cfg
@@ -0,0 +1,86 @@
+#
+# Ethernut 3 board configuration file
+#
+# http://www.ethernut.de/en/hardware/enut3/
+
+
+# AT91R40008-66AU ARM7TDMI Microcontroller
+# 256kB internal RAM
+source [find target/at91r40008.cfg]
+
+
+# AT49BV322A-70TU NOR Flash
+# 2M x 16 mode at address 0x10000000
+# Common flash interface supported
+#
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME cfi 0x10000000 0x400000 2 2 $_TARGETNAME
+
+
+# Micrel MIC2775-29YM5 Supervisor
+# Reset output will remain active for 280ms (maximum)
+#
+jtag_nsrst_delay 300
+jtag_ntrst_delay 300
+
+
+arm7_9 fast_memory_access enable
+arm7_9 dcc_downloads enable
+jtag_khz 16000
+
+
+# Target events
+#
+$_TARGETNAME configure -event reset-init { board_init }
+
+# Initialize board hardware
+#
+proc board_init { } {
+       board_remap
+       flash probe 0
+}
+
+# Memory remap
+#
+proc board_remap {{VERBOSE 0}} {
+       # CS0: NOR flash
+       #      16MB @ 0x10000000
+       #      16-bit data bus
+       #      4 wait states
+       #
+       mww 0xffe00000 0x1000212d
+
+       # CS1: Ethernet controller
+       #      1MB @ 0x20000000
+       #      16-bit data bus
+       #      2 wait states
+       #      Byte select access
+       #
+       mww 0xffe00004 0x20003025
+
+       # CS2: CPLD registers
+       #      1MB @ 0x21000000
+       #      8-bit data bus
+       #      2 wait states
+       #
+       mww 0xffe00008 0x21002026
+
+       # CS3: Expansion bus
+       #      1MB @ 0x22000000
+       #      8-bit data bus
+       #      8 wait states
+       #
+       mww 0xffe00010 0x22002e3e
+
+       # Remap command
+       #
+       mww 0xffe00020 0x00000001
+
+       if {$VERBOSE != 0} {
+               puts "0x00000000 RAM"
+               puts "0x10000000 Flash"
+               puts "0x20000000 Ethernet"
+               puts "0x21000000 CPLD"
+               puts "0x22000000 Expansion"
+       }
+}

diff --git a/tcl/target/at91r40008.cfg b/tcl/target/at91r40008.cfg
index 9069ae563b15f3c4cbe375bf3b9929c55f42bf0b..9c0c4839cef7d79a44ee92d85c0cfaa554f6d6c3 100644 (file)
--- a/tcl/target/at91r40008.cfg
+++ b/tcl/target/at91r40008.cfg
@@ -1,9 +1,13 @@
+# AT91R40008 target configuration file
+
+# TRST is tied to SRST on the AT91X40 family.
+reset_config srst_only srst_pulls_trst
 
 
-if { [info exists CHIPNAME] } {
+if {[info exists CHIPNAME]} {
    set  _CHIPNAME $CHIPNAME
 } else {
-   set  _CHIPNAME at9r40008
+   set  _CHIPNAME at91r40008
 }
 
 if { [info exists ENDIAN] } {
@@ -12,41 +16,14 @@ if { [info exists ENDIAN] } {
    set  _ENDIAN little
 }
 
+# Setup the JTAG scan chain.
 if { [info exists CPUTAPID ] } {
    set _CPUTAPID $CPUTAPID
 } else {
-  # force an error till we get a good number
-   set _CPUTAPID 0xffffffff
+   set _CPUTAPID 0x1f0f0f0f
 }
-
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
 set _TARGETNAME $_CHIPNAME.cpu
 target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi
-
-
-$_TARGETNAME configure -event gdb-flash-erase-start {
-       wait_halt
-       sleep 10
-       poll
-       # Ethernut 3 remapping is required to access external flash memory.
-       mww 0xffe00000 0x1000213d
-       mww 0xffe00004 0x20003e3d
-       mww 0xffe00020 0x00000001
-}
-
-$_TARGETNAME configure -work-area-phys 0x3C000 -work-area-size 0x4000 -work-area-backup 0
-
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME cfi 0x10000000 0x400000 2 2 $_TARGETNAME
-
-# For more information about the configuration files, take a look at:
-# openocd.texi
+$_TARGETNAME configure -work-area-phys 0x20000 -work-area-size 0x20000 -work-area-backup 0