TCL configs for OMAP4430 and Pandaboard

Signed-off-by: Aaron Carroll <aaronc@cse.unsw.edu.au>

diff --git a/tcl/board/ti_pandaboard.cfg b/tcl/board/ti_pandaboard.cfg
new file mode 100644 (file)
index 0000000..bd2cd37
--- /dev/null
+++ b/tcl/board/ti_pandaboard.cfg
@@ -0,0 +1,6 @@
+jtag_rclk 6000
+
+source [find target/omap4430.cfg]
+
+reset_config trst_only
+

diff --git a/tcl/target/omap4430.cfg b/tcl/target/omap4430.cfg
new file mode 100644 (file)
index 0000000..360ac66
--- /dev/null
+++ b/tcl/target/omap4430.cfg
@@ -0,0 +1,106 @@
+# OMAP4430
+
+if { [info exists CHIPNAME] } {
+       set _CHIPNAME $CHIPNAME
+} else {
+       set _CHIPNAME omap4430
+}
+
+
+# Although the OMAP4430 supposedly has an ICEpick-D, only the
+# ICEpick-C router commands seem to work.
+# See http://processors.wiki.ti.com/index.php/ICEPICK
+source [find target/icepick.cfg]
+
+
+#
+# A9 DAP
+#
+if { [info exists DAP_TAPID ] } {
+       set _DAP_TAPID $DAP_TAPID
+} else {
+       set _DAP_TAPID 0x3BA00477
+}
+
+jtag newtap $_CHIPNAME dap -irlen 4 -ircapture 0x1 -irmask 0xf \
+       -expected-id $_DAP_TAPID -disable
+jtag configure $_CHIPNAME.dap -event tap-enable \
+       "icepick_c_tapenable $_CHIPNAME.jrc 9"
+
+
+#
+# M3 DAPs, one per core
+#
+if { [info exists M3_DAP_TAPID ] } {
+       set _M3_DAP_TAPID $M3_DAP_TAPID
+} else {
+       set _M3_DAP_TAPID 0x4BA00477
+}
+
+jtag newtap $_CHIPNAME m31_dap -irlen 4 -ircapture 0x1 -irmask 0xf \
+       -expected-id $_M3_DAP_TAPID -disable
+jtag configure $_CHIPNAME.m31_dap -event tap-enable \
+       "icepick_c_tapenable $_CHIPNAME.jrc 5"
+
+jtag newtap $_CHIPNAME m30_dap -irlen 4 -ircapture 0x1 -irmask 0xf \
+       -expected-id $_M3_DAP_TAPID -disable
+jtag configure $_CHIPNAME.m30_dap -event tap-enable \
+       "icepick_c_tapenable $_CHIPNAME.jrc 4"
+
+
+#
+# ICEpick-D JRC (JTAG route controller)
+#
+if { [info exists JRC_TAPID ] } {
+       set _JRC_TAPID $JRC_TAPID
+} else {
+       set _JRC_TAPID 0x3b95c02f
+}
+
+jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f \
+       -expected-id $_JRC_TAPID
+
+# Required by ICEpick to power-up the debug domain
+jtag configure $_CHIPNAME.jrc -event post-reset "runtest 200"
+
+
+#
+# GDB target: Cortex-A9, using DAP
+#
+# The debugger can connect to either core of the A9, but currently
+# not both simultaneously.  Change -coreid to 1 to connect to the
+# second core.
+#
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_a9 -chain-position $_CHIPNAME.dap -coreid 0
+
+# SRAM: 56KiB at 0x4030.0000
+$_TARGETNAME configure -work-area-phys 0x40300000 -work-area-size 0x1000
+
+
+#
+# M3 targets, separate TAP/DAP for each core
+#
+target create $_CHIPNAME.m30 cortex_m3 -chain-position $_CHIPNAME.m30_dap
+target create $_CHIPNAME.m31 cortex_m3 -chain-position $_CHIPNAME.m31_dap
+
+
+# Once the JRC is up, enable our TAPs
+jtag configure $_CHIPNAME.jrc -event setup "
+       jtag tapenable $_CHIPNAME.dap
+       jtag tapenable $_CHIPNAME.m30_dap
+       jtag tapenable $_CHIPNAME.m31_dap
+"
+
+proc omap4_dbginit {target} {
+       # General Cortex A9 debug initialisation
+       cortex_a9 dbginit
+}
+
+$_TARGETNAME configure -event reset-assert-post "omap4_dbginit $_TARGETNAME"
+
+# Assume SRST is unavailable (e.g. TI-14 JTAG), so we must assert reset
+# ourselves using PRM_RSTCTRL.  1 is a warm reset, 2 a cold reset.
+set PRM_RSTCTRL 0x4A307B00
+$_TARGETNAME configure -event reset-assert "$_TARGETNAME mww $PRM_RSTCTRL 0x1"
+