set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x40700f0f
set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x1f0f0f0f
jtag_rclk 1000
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07926031
set _ENDIAN little
}
-if { [info exists FLASHTAPID ] } {
+if { [info exists FLASHTAPID] } {
set _FLASHTAPID $FLASHTAPID
} else {
set _FLASHTAPID 0x04570041
}
jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x25966041
}
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-if { [info exists BSTAPID ] } {
+if { [info exists BSTAPID] } {
set _BSTAPID $BSTAPID
} else {
# Found on STR9-comStick, revision STR912CS-A1
set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x0032409d
set _ENDIAN little
}
-if { [info exists FLASHTAPID ] } {
+if { [info exists FLASHTAPID] } {
set _FLASHTAPID $FLASHTAPID
} else {
set _FLASHTAPID 0x04570041
jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x25966041
}
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-if { [info exists BSTAPID ] } {
+if { [info exists BSTAPID] } {
set _BSTAPID $BSTAPID
} else {
set _BSTAPID 0x1457f041
#jtag scan chain
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x1f0f0f0f
set rstc_mr_val [expr ($rstc_mr_val | $::AT91_RSTC_URSTEN)]
mww $::AT91_RSTC_MR $rstc_mr_val ;# user reset enable
- if { [info exists config(sdram_piod) ] } {
+ if { [info exists config(sdram_piod)] } {
set pdr_addr [expr ($::AT91_PIOD + $::PIO_PDR)]
set pudr_addr [expr ($::AT91_PIOD + $::PIO_PUDR)]
set asr_addr [expr ($::AT91_PIOD + $::PIO_ASR)]
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME aduc702x
+ set _CHIPNAME aduc702x
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- # This config file was defaulting to big endian..
- set _ENDIAN little
+ # This config file was defaulting to big endian..
+ set _ENDIAN little
}
if { [info exists CPUTAPID] } {
- set _CPUTAPID $CPUTAPID
+ set _CPUTAPID $CPUTAPID
} else {
- set _CPUTAPID 0x3f0f0f0f
+ set _CPUTAPID 0x3f0f0f0f
}
adapter_nsrst_delay 200
if { [info exists CHIPTYPE] } {
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME $CHIPTYPE
+ set _CHIPNAME $CHIPTYPE
}
switch $CHIPTYPE {
if {[info exists CHIPNAME]} {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME at91r40008
+ set _CHIPNAME at91r40008
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
# Setup the JTAG scan chain.
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x1f0f0f0f
# http://atmel.com/products/at91/
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME at91rm9200
+ set _CHIPNAME at91rm9200
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x05b0203f
# at91sam3s1a
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME sam3
+ set _CHIPNAME sam3
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-
#jtag scan chain
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x4ba00477
set _CHIPNAME at91sam3n
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x4ba00477
-
# ATMEL sam7se512
# Example: the "Elektor Internet Radio" - EIR
# http://www.ethernut.de/en/hardware/eir/index.html
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME sam7se512
+ set _CHIPNAME sam7se512
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# Force an error until we get a good number.
reset_config srst_only srst_pulls_trst
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME at91sam7s
+ set _CHIPNAME at91sam7s
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x3f0f0f0f
reset_config srst_only srst_pulls_trst
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME sam7x256
+ set _CHIPNAME sam7x256
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x3f0f0f0f
set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x0792603f
# Faster memory downloads. This is disabled automatically during
# reset init since all reset init sequences are too short for
# fast memory access
-arm7_9 dcc_downloads enable
+arm7_9 dcc_downloads enable
arm7_9 fast_memory_access enable
proc at91sam_init { } {
######################################
if { [info exists CHIPNAME] } {
- set AT91_CHIPNAME $CHIPNAME
+ set AT91_CHIPNAME $CHIPNAME
} else {
- set AT91_CHIPNAME at91sam9rl
+ set AT91_CHIPNAME at91sam9rl
}
source [find target/at91sam9.cfg]
# for avr
- set _CHIPNAME avr
- set _ENDIAN little
+ set _CHIPNAME avr
+ set _ENDIAN little
# jtag speed
adapter_khz 4500
-reset_config srst_only
+reset_config srst_only
adapter_nsrst_delay 100
#jtag scan chain
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x8970203F
-set _CHIPNAME avr32
-set _ENDIAN big
+set _CHIPNAME avr32
+set _ENDIAN big
-set _CPUTAPID 0x21e8203f
+set _CPUTAPID 0x21e8203f
jtag_nsrst_delay 100
jtag_ntrst_delay 100
# jtag scan chain
# format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_CPUTAPID
+jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_CPUTAPID
set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
target create $_TARGETNAME avr32_ap7k -endian $_ENDIAN -chain-position $_TARGETNAME
adapter_khz 100
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME c100
+ set _CHIPNAME c100
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x27b3645b
}
-if { [info exists DSPTAPID ] } {
+if { [info exists DSPTAPID] } {
set _DSPTAPID $DSPTAPID
} else {
set _DSPTAPID 0x27b3645b
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME cs351x
+ set _CHIPNAME cs351x
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x00526fa1
}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
# Create the GDB Target.
set _TARGETNAME $_CHIPNAME.cpu
# There is 16K of SRAM on this chip
# FIXME: flash programming is not working by using this work area. So comment this out for now.
-#$_TARGETNAME configure -work-area-phys 0x00000000 -work-area-size 0x4000 -work-area-backup 1
+#$_TARGETNAME configure -work-area-phys 0x00000000 -work-area-size 0x4000 -work-area-backup 1
# This chip has a DCC ... use it
arm7_9 dcc_downloads enable
# Utility code for DaVinci-family chips
#
-# davinci_pinmux: assigns PINMUX$reg <== $value
+# davinci_pinmux: assigns PINMUX$reg <== $value
proc davinci_pinmux {soc reg value} {
mww [expr [dict get $soc sysbase] + 4 * $reg] $value
}
#
# PLL version 0x02: tested on dm355
-# REVISIT: On dm6446/dm357 the PLLRST polarity is different.
+# REVISIT: On dm6446/dm357 the PLLRST polarity is different.
proc pll_v02_setup {pll_addr mult config} {
set pll_ctrl_addr [expr $pll_addr + 0x100]
set pll_ctrl [mrw $pll_ctrl_addr]
# 1 - clear CLKMODE (bit 8) iff using on-chip oscillator
- # NOTE: this assumes we should clear that bit
+ # NOTE: this assumes we should clear that bit
set pll_ctrl [expr $pll_ctrl & ~0x0100]
mww $pll_ctrl_addr $pll_ctrl
set pll_ctrl [expr $pll_ctrl & ~0x0010]
mww $pll_ctrl_addr $pll_ctrl
- # 9 - optional: write prediv, postdiv, and pllm
- # NOTE: for dm355 PLL1, postdiv is controlled via MISC register
+ # 9 - optional: write prediv, postdiv, and pllm
+ # NOTE: for dm355 PLL1, postdiv is controlled via MISC register
mww [expr $pll_addr + 0x0110] [expr ($mult - 1) & 0xff]
if { [dict exists $config prediv] } {
set div [dict get $config prediv]
mww [expr $pll_addr + 0x0128] $div
}
- # 10 - optional: set plldiv1, plldiv2, ...
+ # 10 - optional: set plldiv1, plldiv2, ...
# NOTE: this assumes some registers have their just-reset values:
# - PLLSTAT.GOSTAT is clear when we enter
# - ALNCTL has everything set
set pll_ctrl [expr $pll_ctrl & ~0x0008]
mww $pll_ctrl_addr $pll_ctrl
- # 9 - optional: write prediv, postdiv, and pllm
+ # 9 - optional: write prediv, postdiv, and pllm
mww [expr $pll_addr + 0x0110] [expr ($mult / 2) & 0x1ff]
if { [dict exists $config prediv] } {
set div [dict get $config prediv]
mww $pll_secctrl_addr 0x00400000
mww $pll_secctrl_addr 0x00410000
- # 11 - optional: set plldiv1, plldiv2, ...
- # NOTE: this assumes some registers have their just-reset values:
+ # 11 - optional: set plldiv1, plldiv2, ...
+ # NOTE: this assumes some registers have their just-reset values:
# - PLLSTAT.GOSTAT is clear when we enter
set aln 0
if { [dict exists $config div1] } {
mww $pll_ctrl_addr $pll_ctrl
}
-# NOTE: dm6446 requires EMURSTIE set in MDCTL before certain
+# NOTE: dm6446 requires EMURSTIE set in MDCTL before certain
# modules can be enabled.
# prepare a non-DSP module to be enabled; finish with psc_go
######################################
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME dragonite
+ set _CHIPNAME dragonite
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x121003d3
#
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME dsp56321
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME dsp56321
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
+ set _ENDIAN $ENDIAN
+} else {
# this defaults to a big endian
- set _ENDIAN big
+ set _ENDIAN big
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x1181501d
# Script for freescale DSP568013
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME dsp568013
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME dsp568013
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
+ set _ENDIAN $ENDIAN
+} else {
# this defaults to a big endian
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x01f2401d
#disables the master tap
jtag configure $_TARGETNAME -event tap-disable "
"
-#TODO FIND SMARTER WAY.
+#TODO FIND SMARTER WAY.
jtag configure $_CHIPNAME.chp -event tap-disable "
"
-#TODO FIND SMARTER WAY.
+#TODO FIND SMARTER WAY.
#working area at base of ram
# Script for freescale DSP568037
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME dsp568037
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME dsp568037
}
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
# this defaults to a big endian
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x01f2801d
#disables the master tap
jtag configure $_TARGETNAME -event tap-disable "
"
-#TODO FIND SMARTER WAY.
+#TODO FIND SMARTER WAY.
jtag configure $_CHIPNAME.chp -event tap-disable "
"
-#TODO FIND SMARTER WAY.
+#TODO FIND SMARTER WAY.
#working area at base of ram
# Cirrus Logic EP9301 processor on an Olimex CS-E9301 board.
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME ep9301
+ set _CHIPNAME ep9301
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# Force an error until we get a good number.
#Script for faux target - used for testing
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME at91eb40a
+ set _CHIPNAME at91eb40a
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x00000000
######################################
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME feroceon
+ set _CHIPNAME feroceon
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x20a023d3
# Fujitsu Cortex-M3 with 512kB Flash and 64kB RAM
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME mb9bf500
+ set _CHIPNAME mb9bf500
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x4ba00477
#Hilscher netX 10 CPU
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME netx10
+ set _CHIPNAME netx10
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x25966021
#Hilscher netX 50 CPU
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME netx50
+ set _CHIPNAME netx50
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x25966021
#Hilscher netX 500 CPU
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME netx500
+ set _CHIPNAME netx500
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07926021
proc sdram_fix { } {
set accesskey [mread32 0x00100070]
- mww 0x00100070 [expr $accesskey]
- mww 0x0010002c 0x00000001
+ mww 0x00100070 [expr $accesskey]
+ mww 0x0010002c 0x00000001
if {[expr [mread32 0x0010002c] & 0x07] == 0x07} {
puts "SDRAM Fix was not executed. Probably your CPU halted too late and the register is already locked!"
# echo "Configuring the ICEpick"
icepick_c_setup $jrc
- # NOTE: it's important not to enter RUN/IDLE state until
+ # NOTE: it's important not to enter RUN/IDLE state until
# done sending these instructions and data to the ICEpick.
# And never to enter RESET, which will disable the TAPs.
# utility fn's for Freescale i.MX series
-global TARGETNAME
+global TARGETNAME
set TARGETNAME $_TARGETNAME
# rewrite commands of the form below to arm11 mcr...
proc setc15 {regs value} {
global TARGETNAME
- echo [format "set p15 0x%04x, 0x%08x" $regs $value]
+ echo [format "set p15 0x%04x, 0x%08x" $regs $value]
- arm mcr 15 [expr ($regs>>12)&0x7] [expr ($regs>>0)&0xf] [expr ($regs>>4)&0xf] [expr ($regs>>8)&0x7] $value
+ arm mcr 15 [expr ($regs>>12)&0x7] [expr ($regs>>0)&0xf] [expr ($regs>>4)&0xf] [expr ($regs>>8)&0x7] $value
}
# this reset script comes from the Freescale PDK
#
# http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=IMX35PDK
-
+
echo "Target Setup: initialize DRAM controller and peripherals"
-
+
# Data.Set c15:0x01 %long 0x00050078
setc15 0x01 0x00050078
-
+
echo "configuring CP15 for enabling the peripheral bus"
# Data.Set c15:0x042f %long 0x40000015
setc15 0x042f 0x40000015
reset_config trst_and_srst
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME imx21
+ set _CHIPNAME imx21
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
# Note above there is 1 tap
# The CPU tap
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x0792611f
}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
# Create the GDB Target.
#
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME imx25
+ set _CHIPNAME imx25
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists ETBTAPID ] } {
+if { [info exists ETBTAPID] } {
set _ETBTAPID $ETBTAPID
} else {
set _ETBTAPID 0x1b900f0f
}
jtag newtap $_CHIPNAME etb -irlen 4 -irmask 0x0f -expected-id $_ETBTAPID
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07926041
jtag newtap $_CHIPNAME whatchacallit -irlen 4 -ircapture 0x0 -irmask 0x0 -expected-id 0x0
-if { [info exists SDMATAPID ] } {
+if { [info exists SDMATAPID] } {
set _SDMATAPID $SDMATAPID
} else {
set _SDMATAPID 0x0882301d
reset_config trst_and_srst srst_pulls_trst
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME imx27
+ set _CHIPNAME imx27
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
# Note above there are 2 taps
# trace buffer
-if { [info exists ETBTAPID ] } {
+if { [info exists ETBTAPID] } {
set _ETBTAPID $ETBTAPID
} else {
set _ETBTAPID 0x1b900f0f
}
-jtag newtap $_CHIPNAME etb -irlen 4 -irmask 0xf -expected-id $_ETBTAPID
+jtag newtap $_CHIPNAME etb -irlen 4 -irmask 0xf -expected-id $_ETBTAPID
# The CPU tap
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07926121
}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
# Create the GDB Target.
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs
# REVISIT what operating environment sets up this virtual address mapping?
$_TARGETNAME configure -work-area-virt 0xffff4c00 -work-area-phys 0xffff4c00 \
- -work-area-size 0x8000 -work-area-backup 1
+ -work-area-size 0x8000 -work-area-backup 1
# Internal to the chip, there is 45K of SRAM
#
adapter_nsrst_delay 5
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME imx31
+ set _CHIPNAME imx31
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07b3601d
}
-if { [info exists SDMATAPID ] } {
+if { [info exists SDMATAPID] } {
set _SDMATAPID $SDMATAPID
} else {
set _SDMATAPID 0x2190101d
}
-if { [info exists ETBTAPID ] } {
+if { [info exists ETBTAPID] } {
set _ETBTAPID $ETBTAPID
} else {
set _ETBTAPID 0x2b900f0f
jtag_ntrst_delay 100
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME imx35
+ set _CHIPNAME imx35
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07b3601d
}
-if { [info exists SDMATAPID ] } {
+if { [info exists SDMATAPID] } {
set _SDMATAPID $SDMATAPID
} else {
set _SDMATAPID 0x0882601d
}
-if { [info exists ETBTAPID ] } {
+if { [info exists ETBTAPID] } {
set _ETBTAPID $ETBTAPID
} else {
set _ETBTAPID 0x2b900f0f
# Freescale i.MX51
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME imx51
+ set _CHIPNAME imx51
}
# CoreSight Debug Access Port
-if { [info exists DAP_TAPID ] } {
+if { [info exists DAP_TAPID] } {
set _DAP_TAPID $DAP_TAPID
} else {
set _DAP_TAPID 0x1ba00477
jtag newtap $_CHIPNAME SDMA -irlen 4 -ircapture 0x0 -irmask 0xf
# SJC
-if { [info exists SJC_TAPID ] } {
+if { [info exists SJC_TAPID] } {
set _SJC_TAPID SJC_TAPID
} else {
set _SJC_TAPID 0x0190c01d
jtag newtap $_CHIPNAME SJC -irlen 5 -ircapture 0x1 -irmask 0x1f \
-expected-id $_SJC_TAPID -ignore-version
-# GDB target: Cortex-A8, using DAP
+# GDB target: Cortex-A8, using DAP
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_a8 -chain-position $_CHIPNAME.DAP
# Freescale i.MX53
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME imx53
+ set _CHIPNAME imx53
}
# CoreSight Debug Access Port
-if { [info exists DAP_TAPID ] } {
+if { [info exists DAP_TAPID] } {
set _DAP_TAPID $DAP_TAPID
} else {
set _DAP_TAPID 0x1ba00477
jtag newtap $_CHIPNAME SDMA -irlen 4 -ircapture 0x0 -irmask 0xf
# SJC
-if { [info exists SJC_TAPID ] } {
+if { [info exists SJC_TAPID] } {
set _SJC_TAPID SJC_TAPID
} else {
set _SJC_TAPID 0x0190d01d
jtag newtap $_CHIPNAME SJC -irlen 5 -ircapture 0x1 -irmask 0x1f \
-expected-id $_SJC_TAPID -ignore-version
-# GDB target: Cortex-A8, using DAP
+# GDB target: Cortex-A8, using DAP
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_a8 -chain-position $_CHIPNAME.DAP
# ATMEL sold his product line to Insilica...
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME is5114
+ set _CHIPNAME is5114
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
# this defaults to a little endian
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# Force an error until we get a good number.
#arm946e-s and
set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
+target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
$_TARGETNAME configure -event reset-start { jtag_rclk 16 }
$_TARGETNAME configure -event reset-init {
#xscale ixp42x CPU
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME ixp42x
+ set _CHIPNAME ixp42x
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
# this defaults to a bigendian
- set _ENDIAN big
+ set _ENDIAN big
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x19274013
set IXP425_SDRAM_IR_MODE_SET_CAS2_CMD 0x0000
set IXP425_SDRAM_IR_MODE_SET_CAS3_CMD 0x0001
-global IXP42x_SDRAM_CL3
-global IXP42x_SDRAM_CL2
+global IXP42x_SDRAM_CL3
+global IXP42x_SDRAM_CL2
set IXP42x_SDRAM_CL3 0x0008
set IXP42x_SDRAM_CL2 0x0000
-global IXP42x_SDRAM_8MB_2Mx32_1BANK
-global IXP42x_SDRAM_16MB_2Mx32_2BANK
-global IXP42x_SDRAM_16MB_4Mx16_1BANK
-global IXP42x_SDRAM_32MB_4Mx16_2BANK
-global IXP42x_SDRAM_32MB_8Mx16_1BANK
-global IXP42x_SDRAM_64MB_8Mx16_2BANK
-global IXP42x_SDRAM_64MB_16Mx16_1BANK
-global IXP42x_SDRAM_128MB_16Mx16_2BANK
-global IXP42x_SDRAM_128MB_32Mx16_1BANK
-global IXP42x_SDRAM_256MB_32Mx16_2BANK
+global IXP42x_SDRAM_8MB_2Mx32_1BANK
+global IXP42x_SDRAM_16MB_2Mx32_2BANK
+global IXP42x_SDRAM_16MB_4Mx16_1BANK
+global IXP42x_SDRAM_32MB_4Mx16_2BANK
+global IXP42x_SDRAM_32MB_8Mx16_1BANK
+global IXP42x_SDRAM_64MB_8Mx16_2BANK
+global IXP42x_SDRAM_64MB_16Mx16_1BANK
+global IXP42x_SDRAM_128MB_16Mx16_2BANK
+global IXP42x_SDRAM_128MB_32Mx16_1BANK
+global IXP42x_SDRAM_256MB_32Mx16_2BANK
set IXP42x_SDRAM_8MB_2Mx32_1BANK 0x0030
set IXP42x_SDRAM_16MB_2Mx32_2BANK 0x0031
proc ixp42x_init_sdram { SDRAM_CFG REFRESH CASLAT } {
switch $CASLAT {
- 2 {
- set SDRAM_CFG [expr $SDRAM_CFG | $::IXP42x_SDRAM_CL2 ]
- set CASCMD $::IXP425_SDRAM_IR_MODE_SET_CAS2_CMD
+ 2 {
+ set SDRAM_CFG [expr $SDRAM_CFG | $::IXP42x_SDRAM_CL2 ]
+ set CASCMD $::IXP425_SDRAM_IR_MODE_SET_CAS2_CMD
}
3 {
- set SDRAM_CFG [expr $SDRAM_CFG | $::IXP42x_SDRAM_CL3 ]
- set CASCMD $::IXP425_SDRAM_IR_MODE_SET_CAS3_CMD
+ set SDRAM_CFG [expr $SDRAM_CFG | $::IXP42x_SDRAM_CL3 ]
+ set CASCMD $::IXP425_SDRAM_IR_MODE_SET_CAS3_CMD
}
default { error [format "unsupported cas latency \"%s\" " $CASLAT] }
}
set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x4ba00477
source [find target/swj-dp.tcl]
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME lpc1768
+ set _CHIPNAME lpc1768
}
# After reset the chip is clocked by the ~4MHz internal RC oscillator.
# (The ROM code doing those updates cares about core clock speed...)
#
# CCLK is the core clock frequency in KHz
-if { [info exists CCLK ] } {
+if { [info exists CCLK] } {
set _CCLK $CCLK
} else {
set _CCLK 4000
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x4ba00477
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME lpc2900
+ set _CHIPNAME lpc2900
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x0596802B
}
-if { [info exists HAS_ETB ] } {
+if { [info exists HAS_ETB] } {
} else {
# Set default (no ETB).
# Show a warning, because this should have been configured explicitely.
set HAS_ETB 0
- # TODO warning?
+ # TODO: warning?
}
-if { [info exists ETBTAPID ] } {
+if { [info exists ETBTAPID] } {
set _ETBTAPID $ETBTAPID
} else {
set _ETBTAPID 0x1B900F0F
arm7_9 dcc_downloads enable
# Flash bank configuration:
-# Flash: flash bank lpc2900 0 0 0 0 <target#> <flash clock (CLK_SYS_FMC) in kHz>
+# Flash: flash bank lpc2900 0 0 0 0 <target#> <flash clock (CLK_SYS_FMC) in kHz>
# Flash base address, total flash size, and number of sectors are all configured automatically.
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME lpc2900 0 0 0 0 $_TARGETNAME $FLASH_CLOCK
proc setup_lpc2xxx {chip_name cputapids flash_size flash_variant workarea_size core_freq_khz adapter_freq_khz} {
reset_config trst_and_srst
-
+
# reset delays
adapter_nsrst_delay 100
jtag_ntrst_delay 100
-
+
adapter_khz $adapter_freq_khz
-
+
foreach i $cputapids {
append expected_ids "-expected-id " $i " "
}
-
+
eval "jtag newtap $chip_name cpu -irlen 4 -ircapture 0x1 -irmask 0xf $expected_ids"
-
+
set _TARGETNAME $chip_name.cpu
target create $_TARGETNAME arm7tdmi -chain-position $_TARGETNAME
-
+
$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size $workarea_size -work-area-backup 0
-
+
if { $flash_size > 0 } {
# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
set _FLASHNAME $chip_name.flash
######################################
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME lpc3131
+ set _CHIPNAME lpc3131
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
# ARM926EJS core
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07926f0f
# Scan Tap
# Wired to seperate STDO pin on the lpc3131, externally muxed to TDO on ea3131 module
# JTAGSEL pin must be 0 to activate, which reassigns arm tdo to a pass through.
-if { [info exists SJCTAPID ] } {
+if { [info exists SJCTAPID] } {
set _SJCTAPID $SJCTAPID
} else {
set _SJCTAPID 0x1541E02B
#
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME lpc3250
+ set _CHIPNAME lpc3250
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x17900f0f
}
-if { [info exists CPUTAPID_REV_A0 ] } {
+if { [info exists CPUTAPID_REV_A0] } {
set _CPUTAPID_REV_A0 $CPUTAPID_REV_A0
} else {
set _CPUTAPID_REV_A0 0x17926f0f
}
-if { [info exists SJCTAPID ] } {
+if { [info exists SJCTAPID] } {
set _SJCTAPID $SJCTAPID
} else {
set _SJCTAPID 0x1b900f0f
source [find memory.tcl]
source [find mmr_helpers.tcl]
-set CHIP_MAKER freescale
-set CHIP_FAMILY mc1322x
-set CHIP_NAME mc13224
-set N_RAM 1
-set RAM(0,BASE) 0x00400000
-set RAM(0,LEN) 0x18000
-set RAM(0,HUMAN) "internal SRAM"
+set CHIP_MAKER freescale
+set CHIP_FAMILY mc1322x
+set CHIP_NAME mc13224
+set N_RAM 1
+set RAM(0,BASE) 0x00400000
+set RAM(0,LEN) 0x18000
+set RAM(0,HUMAN) "internal SRAM"
set RAM(0,TYPE) "ram"
set RAM(0,RWX) $RWX_RWX
set RAM(0,ACCESS_WIDTH) $ACCESS_WIDTH_ANY
# I AM LAZY... I create 1 region for all MMRs.
-set N_MMREGS 1
+set N_MMREGS 1
set MMREGS(0,CHIPSELECT) -1
set MMREGS(0,BASE) 0x80000000
set MMREGS(0,LEN) 0x00030000
#
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME nuc910
+ set _CHIPNAME nuc910
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# set useful default
# as seen in Nokia N8x0 tablets
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME omap2420
+ set _CHIPNAME omap2420
}
# NOTE: likes slowish clock on reset (1.5 MBit/s or less) or use RCLK
reset_config srst_nogate
-# Subsidiary TAP: ARM7TDMIr4 plus imaging ... must add via ICEpick (addr 6).
+# Subsidiary TAP: ARM7TDMIr4 plus imaging ... must add via ICEpick (addr 6).
jtag newtap $_CHIPNAME iva -irlen 4 -disable
# Subsidiary TAP: C55x DSP ... must add via ICEpick (addr 2).
jtag newtap $_CHIPNAME dsp -irlen 38 -disable
# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
-if { [info exists ETB_TAPID ] } {
+if { [info exists ETB_TAPID] } {
set _ETB_TAPID $ETB_TAPID
} else {
set _ETB_TAPID 0x2b900f0f
jtag newtap $_CHIPNAME etb -irlen 4 -expected-id $_ETB_TAPID
# Subsidiary TAP: ARM1136jf-s with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
-if { [info exists CPU_TAPID ] } {
+if { [info exists CPU_TAPID] } {
set _CPU_TAPID $CPU_TAPID
} else {
set _CPU_TAPID 0x07b3602f
jtag newtap $_CHIPNAME arm -irlen 5 -expected-id $_CPU_TAPID
# Primary TAP: ICEpick-B (JTAG route controller) and boundary scan
-if { [info exists JRC_TAPID ] } {
+if { [info exists JRC_TAPID] } {
set _JRC_TAPID $JRC_TAPID
} else {
set _JRC_TAPID 0x01ce4801
}
jtag newtap $_CHIPNAME jrc -irlen 2 -expected-id $_JRC_TAPID
-# GDB target: the ARM.
+# GDB target: the ARM.
set _TARGETNAME $_CHIPNAME.arm
target create $_TARGETNAME arm11 -chain-position $_TARGETNAME
-# scratch: framebuffer, may be initially unavailable in some chips
+# scratch: framebuffer, may be initially unavailable in some chips
$_TARGETNAME configure -work-area-phys 0x40210000
$_TARGETNAME configure -work-area-size 0x00081000
$_TARGETNAME configure -work-area-backup 0
# TI OMAP3530
-# http://focus.ti.com/docs/prod/folders/print/omap3530.html
+# http://focus.ti.com/docs/prod/folders/print/omap3530.html
# Other OMAP3 chips remove DSP and/or the OpenGL support
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME omap3530
+ set _CHIPNAME omap3530
}
# ICEpick-C ... used to route Cortex, DSP, and more not shown here
jtag newtap $_CHIPNAME dsp -irlen 38 -ircapture 0x25 -irmask 0x3f -disable
# Subsidiary TAP: CoreSight Debug Access Port (DAP)
-if { [info exists DAP_TAPID ] } {
+if { [info exists DAP_TAPID] } {
set _DAP_TAPID $DAP_TAPID
} else {
set _DAP_TAPID 0x0b6d602f
"icepick_c_tapenable $_CHIPNAME.jrc 3"
# Primary TAP: ICEpick-C (JTAG route controller) and boundary scan
-if { [info exists JRC_TAPID ] } {
+if { [info exists JRC_TAPID] } {
set _JRC_TAPID $JRC_TAPID
} else {
set _JRC_TAPID 0x0b7ae02f
jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f \
-expected-id $_JRC_TAPID
-# GDB target: Cortex-A8, using DAP
+# GDB target: Cortex-A8, using DAP
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_a8 -chain-position $_CHIPNAME.dap
#
# A9 DAP
#
-if { [info exists DAP_TAPID ] } {
+if { [info exists DAP_TAPID] } {
set _DAP_TAPID $DAP_TAPID
} else {
set _DAP_TAPID 0x3BA00477
#
# M3 DAPs, one per core
#
-if { [info exists M3_DAP_TAPID ] } {
+if { [info exists M3_DAP_TAPID] } {
set _M3_DAP_TAPID $M3_DAP_TAPID
} else {
set _M3_DAP_TAPID 0x4BA00477
#
# ICEpick-D JRC (JTAG route controller)
#
-if { [info exists JRC_TAPID ] } {
+if { [info exists JRC_TAPID] } {
set _JRC_TAPID $JRC_TAPID
} else {
set _JRC_TAPID 0x3b95c02f
}
# PandaBoard REV EA1 (PEAP platforms)
-if { [info exists JRC_TAPID2 ] } {
+if { [info exists JRC_TAPID2] } {
set _JRC_TAPID2 $JRC_TAPID2
} else {
set _JRC_TAPID2 0x1b85202f
jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f \
- -expected-id $_JRC_TAPID -expected-id $_JRC_TAPID2
+ -expected-id $_JRC_TAPID -expected-id $_JRC_TAPID2
# Required by ICEpick to power-up the debug domain
jtag configure $_CHIPNAME.jrc -event post-reset "runtest 200"
# http://focus.ti.com/docs/prod/folders/print/omap5912.html
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME omap5912
+ set _CHIPNAME omap5912
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# NOTE: validated with XOMAP5912 part
adapter_nsrst_delay 100
-# NOTE: presumes irlen 38 is the C55x DSP, matching BSDL for
+# NOTE: presumes irlen 38 is the C55x DSP, matching BSDL for
# its standalone siblings (like TMS320VC5502) of the same era
#jtag scan chain
#
-# Texas Instruments DaVinci family: OMAPL138
+# Texas Instruments DaVinci family: OMAPL138
#
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME omapl138
+ set _CHIPNAME omapl138
}
source [find target/icepick.cfg]
# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
-if { [info exists ETB_TAPID ] } {
+if { [info exists ETB_TAPID] } {
set _ETB_TAPID $ETB_TAPID
} else {
set _ETB_TAPID 0x2b900f0f
"icepick_c_tapenable $_CHIPNAME.jrc 3"
# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
-if { [info exists CPU_TAPID ] } {
+if { [info exists CPU_TAPID] } {
set _CPU_TAPID $CPU_TAPID
} else {
set _CPU_TAPID 0x07926001
"icepick_c_tapenable $_CHIPNAME.jrc 2"
# Primary TAP: ICEpick-C (JTAG route controller) and boundary scan
-if { [info exists JRC_TAPID ] } {
+if { [info exists JRC_TAPID] } {
set _JRC_TAPID $JRC_TAPID
} else {
set _JRC_TAPID 0x0b7d102f
-
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME pic32mx
+ set _CHIPNAME pic32mx
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x30938053
# default working area is 16384
if { [info exists WORKAREASIZE] } {
- set _WORKAREASIZE $WORKAREASIZE
+ set _WORKAREASIZE $WORKAREASIZE
} else {
- set _WORKAREASIZE 0x4000
+ set _WORKAREASIZE 0x4000
}
-
adapter_nsrst_delay 100
jtag_ntrst_delay 100
# PXA255 chip ... originally from Intel, PXA line was sold to Marvell.
-# This chip is now at end-of-life. Final orders have been taken.
+# This chip is now at end-of-life. Final orders have been taken.
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME pxa255
+ set _CHIPNAME pxa255
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x69264013
#Marvell/Intel PXA270 Script
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME pxa270
+ set _CHIPNAME pxa270
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
#IDs for pxa270. Are there more?
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# set useful default
set _CPUTAPID 0x49265013
}
-if { [info exists CPUTAPID2 ] } {
+if { [info exists CPUTAPID2] } {
set _CPUTAPID2 $CPUTAPID2
} else {
# set useful default
set _CPUTAPID2 0x79265013
}
-if { [info exists CPUTAPID3 ] } {
+if { [info exists CPUTAPID3] } {
set _CPUTAPID2 $CPUTAPID3
} else {
# set useful default
# Marvell PXA3xx
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME pxa3xx
+ set _CHIPNAME pxa3xx
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
# IDs for all currently known PXA3xx chips
-if { [info exists CPUTAPID_PXA30X_A0 ] } {
+if { [info exists CPUTAPID_PXA30X_A0] } {
set _CPUTAPID_PXA30X_A0 $CPUTAPID_PXA30X_A0
} else {
set _CPUTAPID_PXA30X_A0 0x0E648013
}
-if { [info exists CPUTAPID_PXA30X_A1 ] } {
+if { [info exists CPUTAPID_PXA30X_A1] } {
set _CPUTAPID_PXA30X_A1 $CPUTAPID_PXA30X_A1
} else {
set _CPUTAPID_PXA30X_A1 0x1E648013
}
-if { [info exists CPUTAPID_PXA31X_A0 ] } {
+if { [info exists CPUTAPID_PXA31X_A0] } {
set _CPUTAPID_PXA31X_A0 $CPUTAPID_PXA31X_A0
} else {
set _CPUTAPID_PXA31X_A0 0x0E649013
}
-if { [info exists CPUTAPID_PXA31X_A1 ] } {
+if { [info exists CPUTAPID_PXA31X_A1] } {
set _CPUTAPID_PXA31X_A1 $CPUTAPID_PXA31X_A1
} else {
set _CPUTAPID_PXA31X_A1 0x1E649013
}
-if { [info exists CPUTAPID_PXA31X_A2 ] } {
+if { [info exists CPUTAPID_PXA31X_A2] } {
set _CPUTAPID_PXA31X_A2 $CPUTAPID_PXA31X_A2
} else {
set _CPUTAPID_PXA31X_A2 0x2E649013
}
-if { [info exists CPUTAPID_PXA31X_B0 ] } {
+if { [info exists CPUTAPID_PXA31X_B0] } {
set _CPUTAPID_PXA31X_B0 $CPUTAPID_PXA31X_B0
} else {
set _CPUTAPID_PXA31X_B0 0x3E649013
}
-if { [info exists CPUTAPID_PXA32X_B1 ] } {
+if { [info exists CPUTAPID_PXA32X_B1] } {
set _CPUTAPID_PXA32X_B1 $CPUTAPID_PXA32X_B1
} else {
set _CPUTAPID_PXA32X_B1 0x5E642013
}
-if { [info exists CPUTAPID_PXA32X_B2 ] } {
+if { [info exists CPUTAPID_PXA32X_B2] } {
set _CPUTAPID_PXA32X_B2 $CPUTAPID_PXA32X_B2
} else {
set _CPUTAPID_PXA32X_B2 0x6E642013
}
-if { [info exists CPUTAPID_PXA32X_C0 ] } {
+if { [info exists CPUTAPID_PXA32X_C0] } {
set _CPUTAPID_PXA32X_C0 $CPUTAPID_PXA32X_C0
} else {
set _CPUTAPID_PXA32X_C0 0x7E642013
# Found on the 'TinCanTools' Hammer board.
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME s3c2410
+ set _CHIPNAME s3c2410
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
# This config file was defaulting to big endian..
- set _ENDIAN little
+ set _ENDIAN little
}
if { [info exists CPUTAPID] } {
- set _CPUTAPID $CPUTAPID
+ set _CPUTAPID $CPUTAPID
} else {
# Force an error until we get a good number.
- set _CPUTAPID 0xffffffff
+ set _CPUTAPID 0xffffffff
}
#use combined on interfaces or targets that cannot set TRST/SRST separately
# Info: JTAG tap: s3c2440.cpu tap/device found: 0x0032409d (Manufacturer: 0x04e, Part: 0x0324, Version: 0x0)
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME s3c2440
+ set _CHIPNAME s3c2440
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
# this defaults to a bigendian
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x0032409d
# adapter_khz 1
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME s3c2450
+ set _CHIPNAME s3c2450
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
# this defaults to a bigendian
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07926f0f
-
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME s3c4510
+ set _CHIPNAME s3c4510
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
# This appears to be a "Version 1" arm7tdmi.
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x1f0f0f0f
# [and I do not believe it to be accurate, hence the 0xffffffff below]
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME s3c6410
+ set _CHIPNAME s3c6410
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
# this defaults to a bigendian
- set _ENDIAN little
+ set _ENDIAN little
}
# trace buffer
-if { [info exists ETBTAPID ] } {
+if { [info exists ETBTAPID] } {
set _ETBTAPID $ETBTAPID
} else {
set _ETBTAPID 0x2b900f0f
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07b76f0f
#jtag scan chain
jtag newtap $_CHIPNAME etb -irlen 4 -expected-id $_ETBTAPID
-jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_CPUTAPID
+jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_CPUTAPID
set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm11 -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm1176
+target create $_TARGETNAME arm11 -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm1176
adapter_nsrst_delay 500
jtag_ntrst_delay 500
reset_config srst_only srst_pulls_trst
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME lh79532
+ set _CHIPNAME lh79532
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# sharp changed the number!
# script for Sigma Designs SMP8634 (eventually even SMP8635)
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME smp8634
+ set _CHIPNAME smp8634
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x08630001
# jtag scan chain
# format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1
+jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME mips_m4k -endian $_ENDIAN -variant
set _ENDIAN little
}
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07926041
global _DEVICECLASS
-if { [info exists DEVICECLASS ] } {
+if { [info exists DEVICECLASS] } {
set _DEVICECLASS $DEVICECLASS
} else {
set _DEVICECLASS 0xff
# are usable only for ISP style initial flash programming.
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME lm3s
+ set _CHIPNAME lm3s
}
# CPU TAP ID 0x1ba00477 for early Sandstorm parts
# CPU TAP ID 0x4ba00477 for Cortex-M3 r2p0 (on Tempest)
# ... we'll ignore the JTAG version field, rather than list every
# chip revision that turns up.
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x0ba00477
swj_newdap $_CHIPNAME cpu -irlen 4 -irmask 0xf \
-expected-id $_CPUTAPID -ignore-version
-if { [info exists WORKAREASIZE ] } {
+if { [info exists WORKAREASIZE] } {
set _WORKAREASIZE $WORKAREASIZE
} else {
# default to 8K working area
# 8K working area at base of ram, not backed up
#
-# NOTE: you may need or want to reconfigure the work area;
+# NOTE: you may need or want to reconfigure the work area;
# some parts have just 6K, and you may want to use other
# addresses (at end of mem not beginning) or back it up.
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE
# JTAG speed ... slow enough to work with a 12 MHz RC oscillator;
# LM3S parts don't support RTCK
#
-# NOTE: this may be increased by a reset-init handler, after it
+# NOTE: this may be increased by a reset-init handler, after it
# configures and enables the PLL. Or you might need to decrease
# this, if you're using a slower clock.
adapter_khz 500
# script for stm32
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME stm32
+ set _CHIPNAME stm32
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
# Work-area is a space in RAM used for flash programming
# By default use 16kB
if { [info exists WORKAREASIZE] } {
- set _WORKAREASIZE $WORKAREASIZE
+ set _WORKAREASIZE $WORKAREASIZE
} else {
- set _WORKAREASIZE 0x4000
+ set _WORKAREASIZE 0x4000
}
# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
jtag_ntrst_delay 100
#jtag scan chain
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# See STM Document RM0008
}
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-if { [info exists BSTAPID ] } {
+if { [info exists BSTAPID] } {
# FIXME this never gets used to override defaults...
set _BSTAPID $BSTAPID
} else {
# script for stm32f2xxx
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME stm32f2xxx
+ set _CHIPNAME stm32f2xxx
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
# Work-area is a space in RAM used for flash programming
# By default use 64kB
if { [info exists WORKAREASIZE] } {
- set _WORKAREASIZE $WORKAREASIZE
+ set _WORKAREASIZE $WORKAREASIZE
} else {
- set _WORKAREASIZE 0x10000
+ set _WORKAREASIZE 0x10000
}
# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
jtag_ntrst_delay 100
#jtag scan chain
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# See STM Document RM0033
}
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-if { [info exists BSTAPID ] } {
+if { [info exists BSTAPID] } {
set _BSTAPID $BSTAPID
} else {
# See STM Document RM0033
# script for stm32l
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME stm32l
+ set _CHIPNAME stm32l
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
# Work-area is a space in RAM used for flash programming
# By default use 14kB
if { [info exists WORKAREASIZE] } {
- set _WORKAREASIZE $WORKAREASIZE
+ set _WORKAREASIZE $WORKAREASIZE
} else {
- set _WORKAREASIZE 0x3800
+ set _WORKAREASIZE 0x3800
}
# JTAG speed should be <= F_CPU/6.
jtag_ntrst_delay 100
#jtag scan chain
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
# See STM Document RM0038
}
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-if { [info exists BSTAPID ] } {
+if { [info exists BSTAPID] } {
# FIXME this never gets used to override defaults...
set _BSTAPID $BSTAPID
} else {
adapter_khz 10
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME str710
+ set _CHIPNAME str710
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
if { [info exists CPUTAPID] } {
- set _CPUTAPID $CPUTAPID
+ set _CPUTAPID $CPUTAPID
} else {
- set _CPUTAPID 0x3f0f0f0f
+ set _CPUTAPID 0x3f0f0f0f
}
#use combined on interfaces or targets that can't set TRST/SRST separately
adapter_khz 3000
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME str730
+ set _CHIPNAME str730
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
if { [info exists CPUTAPID] } {
- set _CPUTAPID $CPUTAPID
+ set _CPUTAPID $CPUTAPID
} else {
- set _CPUTAPID 0x3f0f0f0f
+ set _CPUTAPID 0x3f0f0f0f
}
#use combined on interfaces or targets that can't set TRST/SRST separately
#STR750 CPU
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME str750
+ set _CHIPNAME str750
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
if { [info exists CPUTAPID] } {
- set _CPUTAPID $CPUTAPID
+ set _CPUTAPID $CPUTAPID
} else {
- set _CPUTAPID 0x4f1f0041
+ set _CPUTAPID 0x4f1f0041
}
# jtag speed
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm7tdmi -endian little -chain-position 0 -variant arm7tdmi
-$_TARGETNAME configure -event reset-start { adapter_khz 10 }
+$_TARGETNAME configure -event reset-start { adapter_khz 10 }
$_TARGETNAME configure -event reset-init {
adapter_khz 3000
# script for str9
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME str912
+ set _CHIPNAME str912
}
if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
+ set _ENDIAN $ENDIAN
} else {
- set _ENDIAN little
+ set _ENDIAN little
}
# jtag speed. We need to stick to 16kHz until we've finished reset.
#use combined on interfaces or targets that can't set TRST/SRST separately
reset_config trst_and_srst
-if { [info exists FLASHTAPID ] } {
+if { [info exists FLASHTAPID] } {
set _FLASHTAPID $FLASHTAPID
} else {
set _FLASHTAPID 0x04570041
}
jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x25966041
}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-if { [info exists BSTAPID ] } {
+if { [info exists BSTAPID] } {
set _BSTAPID $BSTAPID
} else {
set _BSTAPID 0x1457f041
}
-jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID
+jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
#
-# Texas Instruments DaVinci family: TMS320DM355
+# Texas Instruments DaVinci family: TMS320DM355
#
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME dm355
+ set _CHIPNAME dm355
}
# TI boards default to EMU0/EMU1 *high* -- ARM and ETB are *disabled*
source [find target/icepick.cfg]
#
-# Also note: when running without RTCK before the PLLs are set up, you
+# Also note: when running without RTCK before the PLLs are set up, you
# may need to slow the JTAG clock down quite a lot (under 2 MHz).
#
# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
-if { [info exists ETB_TAPID ] } {
+if { [info exists ETB_TAPID] } {
set _ETB_TAPID $ETB_TAPID
} else {
set _ETB_TAPID 0x2b900f0f
"icepick_c_tapenable $_CHIPNAME.jrc 1"
# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
-if { [info exists CPU_TAPID ] } {
+if { [info exists CPU_TAPID] } {
set _CPU_TAPID $CPU_TAPID
} else {
set _CPU_TAPID 0x07926001
"icepick_c_tapenable $_CHIPNAME.jrc 0"
# Primary TAP: ICEpick (JTAG route controller) and boundary scan
-if { [info exists JRC_TAPID ] } {
+if { [info exists JRC_TAPID] } {
set _JRC_TAPID $JRC_TAPID
} else {
set _JRC_TAPID 0x0b73b02f
source [find target/davinci.cfg]
################
-# GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 16K)
+# GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 16K)
# and the ETB memory (4K) are other options, while trace is unused.
set _TARGETNAME $_CHIPNAME.arm
#
-# Texas Instruments DaVinci family: TMS320DM365
+# Texas Instruments DaVinci family: TMS320DM365
#
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME dm365
+ set _CHIPNAME dm365
}
# TI boards default to EMU0/EMU1 *high* -- ARM and ETB are *disabled*
source [find target/icepick.cfg]
# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
-if { [info exists ETB_TAPID ] } {
+if { [info exists ETB_TAPID] } {
set _ETB_TAPID $ETB_TAPID
} else {
set _ETB_TAPID 0x2b900f0f
"icepick_c_tapenable $_CHIPNAME.jrc 1"
# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
-if { [info exists CPU_TAPID ] } {
+if { [info exists CPU_TAPID] } {
set _CPU_TAPID $CPU_TAPID
} else {
set _CPU_TAPID 0x0792602f
"icepick_c_tapenable $_CHIPNAME.jrc 0"
# Primary TAP: ICEpick (JTAG route controller) and boundary scan
-if { [info exists JRC_TAPID ] } {
+if { [info exists JRC_TAPID] } {
set _JRC_TAPID $JRC_TAPID
} else {
set _JRC_TAPID 0x0b83e02f
source [find target/davinci.cfg]
################
-# GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 16K)
+# GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 16K)
# and the ETB memory (4K) are other options, while trace is unused.
set _TARGETNAME $_CHIPNAME.arm
#
-# Texas Instruments DaVinci family: TMS320DM6446
+# Texas Instruments DaVinci family: TMS320DM6446
#
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME dm6446
+ set _CHIPNAME dm6446
}
# TI boards default to EMU0/EMU1 *high* -- ARM and ETB are *disabled*
"icepick_c_tapenable $_CHIPNAME.jrc 2"
# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
-if { [info exists ETB_TAPID ] } {
+if { [info exists ETB_TAPID] } {
set _ETB_TAPID $ETB_TAPID
} else {
set _ETB_TAPID 0x2b900f0f
"icepick_c_tapenable $_CHIPNAME.jrc 1"
# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
-if { [info exists CPU_TAPID ] } {
+if { [info exists CPU_TAPID] } {
set _CPU_TAPID $CPU_TAPID
} else {
set _CPU_TAPID 0x07926001
"icepick_c_tapenable $_CHIPNAME.jrc 0"
# Primary TAP: ICEpick-C (JTAG route controller) and boundary scan
-if { [info exists JRC_TAPID ] } {
+if { [info exists JRC_TAPID] } {
set _JRC_TAPID $JRC_TAPID
} else {
set _JRC_TAPID 0x0b70002f
"jtag tapenable $_CHIPNAME.etb; jtag tapenable $_CHIPNAME.arm"
################
-# GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 8K)
+# GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 8K)
# and the ETB memory (4K) are other options, while trace is unused.
# Little-endian; use the OpenOCD default.
set _TARGETNAME $_CHIPNAME.arm
######################################
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME tmpa900
+ set _CHIPNAME tmpa900
}
# Toshiba TMPA900 series MCUs are always little endian as per datasheet.
set _ENDIAN little
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07926031
######################################
if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
- set _CHIPNAME tmpa910
+ set _CHIPNAME tmpa910
}
# Toshiba TMPA910 series MCUs are always little endian as per datasheet.
set _ENDIAN little
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x07926031
}
proc ocd_gdb_restart {target_id} {
- global _TARGETNAME_1
+ global _TARGETNAME_1
global _SMP
targets $_TARGETNAME_1
if { [expr ($_SMP == 1)] } {
}
proc smp_reg {} {
- global _TARGETNAME_1
- global _TARGETNAME_2
+ global _TARGETNAME_1
+ global _TARGETNAME_2
targets $_TARGETNAME_1
echo "$_TARGETNAME_1"
set pc1 [reg pc]
set stck1 [reg sp_svc]
- targets $_TARGETNAME_2
+ targets $_TARGETNAME_2
echo "$_TARGETNAME_1"
set pc2 [reg pc]
set stck2 [reg sp_svc]
set result 1
set i 0
irscan $_CHIPNAME.jrc 0x3a
- drscan $_CHIPNAME.jrc 4 0
- set pwrsts [drscan $_CHIPNAME.jrc 16 0]
+ drscan $_CHIPNAME.jrc 4 0
+ set pwrsts [drscan $_CHIPNAME.jrc 16 0]
set pwrsts [expr (0x$pwrsts & 0xc)]
while {[string equal "4" $pwrsts] && $i<20} {
irscan $_CHIPNAME.jrc 0x3a
- drscan $_CHIPNAME.jrc 4 0;
- set pwrsts [drscan $_CHIPNAME.jrc 16 0]
+ drscan $_CHIPNAME.jrc 4 0;
+ set pwrsts [drscan $_CHIPNAME.jrc 16 0]
set pwrsts [expr (0x$pwrsts & 0xc)]
if {![string equal "4" $pwrsts]} {
set result 1
}
proc halt_ { } {
- if {[poll_pwrsts]==1} {
+ if {[poll_pwrsts]==1} {
halt
} else {
echo "halt failed : target in retention"
proc enable_apetap {} {
- global _CHIPNAME
- global _TARGETNAME_2
+ global _CHIPNAME
+ global _TARGETNAME_2
global _TARGETNAME_1
poll off
irscan $_CHIPNAME.jrc 0x3e
- drscan $_CHIPNAME.jrc 8 0xcf
+ drscan $_CHIPNAME.jrc 8 0xcf
jtag tapenable $_CHIPNAME.dap
irscan $_CHIPNAME.jrc 0x6
drscan $_CHIPNAME.jrc 32 0
tcl_port 5555
telnet_port 4444
gdb_port 3333
-
+
if { [info exists CHIPNAME] } {
-global _CHIPNAME
- set _CHIPNAME $CHIPNAME
+global _CHIPNAME
+ set _CHIPNAME $CHIPNAME
} else {
-global _CHIPNAME
- set _CHIPNAME u8500
+global _CHIPNAME
+ set _CHIPNAME u8500
}
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
# this defaults to a bigendian
- set _ENDIAN little
+ set _ENDIAN little
}
# Subsidiary TAP: APE with scan chains for ARM Debug, EmbeddedICE-RT,
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x4ba00477
#CLTAPC TAP JRC equivalent
-if { [info exists CLTAPC_ID ] } {
+if { [info exists CLTAPC_ID] } {
set _CLTAPC_ID $CLTAPC_ID
} else {
set _CLTAPC_ID 0x22286041
jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x6 -irmask 0xf -expected-id $_CLTAPC_ID -ignore-version
-if { ![info exists TARGETNAME_1 ] } {
-global _TARGETNAME_1
+if { ![info exists TARGETNAME_1] } {
+global _TARGETNAME_1
set _TARGETNAME_1 $_CHIPNAME.cpu1
} else {
-global _TARGETNAME_1
+global _TARGETNAME_1
set _TARGETNAME_1 $TARGETNAME_1
}
-if { [info exists DAP_DBG1] } {
+if { [info exists DAP_DBG1] } {
set _DAP_DBG1 $DAP_DBG1
} else {
set _DAP_DBG1 0x801A8000
}
-if { [info exists DAP_DBG2] } {
+if { [info exists DAP_DBG2] } {
set _DAP_DBG2 $DAP_DBG2
} else {
set _DAP_DBG2 0x801AA000
}
-if { ![info exists TARGETNAME_2 ] } {
-global _TARGETNAME_2
+if { ![info exists TARGETNAME_2] } {
+global _TARGETNAME_2
set _TARGETNAME_2 $_CHIPNAME.cpu2
} else {
-global _TARGETNAME_2
+global _TARGETNAME_2
set _TARGETNAME_2 $TARGETNAME_2
}
projects / openocd / commitdiff