wide on a sixteen bit bus:
@example
-flash bank cfi 0x00000000 0x01000000 2 2 $_TARGETNAME
-flash bank cfi 0x01000000 0x01000000 2 2 $_TARGETNAME
+flash bank $_FLASHNAME cfi 0x00000000 0x01000000 2 2 $_TARGETNAME
+flash bank $_FLASHNAME cfi 0x01000000 0x01000000 2 2 $_TARGETNAME
@end example
To configure one bank of 32 MBytes
to create a thirty-two bit (four byte) bus with doubled throughput:
@example
-flash bank cfi 0x00000000 0x02000000 2 4 $_TARGETNAME
+flash bank $_FLASHNAME cfi 0x00000000 0x02000000 2 4 $_TARGETNAME
@end example
@c "cfi part_id" disabled
since all devices in this family have the same memory layout.
@example
-flash bank aduc702x 0 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME aduc702x 0 0 0 0 $_TARGETNAME
@end example
@end deffn
@example
# Flash bank 0 - all chips
-flash bank at91sam3 0x00080000 0 1 1 $_TARGETNAME
+flash bank $_FLASHNAME at91sam3 0x00080000 0 1 1 $_TARGETNAME
# Flash bank 1 - only 256K chips
-flash bank at91sam3 0x00100000 0 1 1 $_TARGETNAME
+flash bank $_FLASHNAME at91sam3 0x00100000 0 1 1 $_TARGETNAME
@end example
Internally, the AT91SAM3 flash memory is organized as follows.
register, and autoconfigures itself.
@example
-flash bank at91sam7 0 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME at91sam7 0 0 0 0 $_TARGETNAME
@end example
For chips which are not recognized by the controller driver, you must
LPC flashes don't require the chip and bus width to be specified.
@example
-flash bank lpc2000 0x0 0x7d000 0 0 $_TARGETNAME \
+flash bank $_FLASHNAME lpc2000 0x0 0x7d000 0 0 $_TARGETNAME \
lpc2000_v2 14765 calc_checksum
@end example
LPC flashes don't require the chip and bus width to be specified.
@example
-flash bank lpc288x 0 0 0 0 $_TARGETNAME 12000000
+flash bank $_FLASHNAME lpc288x 0 0 0 0 $_TARGETNAME 12000000
@end example
@end deffn
Example for a 125 MHz clock frequency:
@example
-flash bank lpc2900 0 0 0 0 $_TARGETNAME 125000
+flash bank $_FLASHNAME lpc2900 0 0 0 0 $_TARGETNAME 125000
@end example
Some @code{lpc2900}-specific commands are defined. In the following command list,
@emph{No idea what this is, other than using some arm7/arm9 core.}
@example
-flash bank ocl 0 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME ocl 0 0 0 0 $_TARGETNAME
@end example
@end deffn
and integrate flash memory.
@example
-flash bank pix32mx 0x1fc00000 0 0 0 $_TARGETNAME
-flash bank pix32mx 0x1d000000 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME pix32mx 0x1fc00000 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME pix32mx 0x1d000000 0 0 0 $_TARGETNAME
@end example
@comment numerous *disabled* commands are defined:
standard @command{flash erase_address} command.}
@example
-flash bank stellaris 0 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME stellaris 0 0 0 0 $_TARGETNAME
@end example
@end deffn
the chip identification register, and autoconfigures itself.
@example
-flash bank stm32x 0 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME stm32x 0 0 0 0 $_TARGETNAME
@end example
Some stm32x-specific commands
which is either @code{STR71x}, @code{STR73x} or @code{STR75x}.
@example
-flash bank str7x 0x40000000 0x00040000 0 0 $_TARGETNAME STR71x
+flash bank $_FLASHNAME str7x 0x40000000 0x00040000 0 0 $_TARGETNAME STR71x
@end example
@deffn Command {str7x disable_jtag} bank
the @command{str9x flash_config} command prior to Flash programming.
@example
-flash bank str9x 0x40000000 0x00040000 0 0 $_TARGETNAME
+flash bank $_FLASHNAME str9x 0x40000000 0x00040000 0 0 $_TARGETNAME
str9x flash_config 0 4 2 0 0x80000
@end example
Example for s3c2440 mflash where @var{RST pin} is GPIO B1:
@example
-mflash bank s3c2440 0x10000000 1b 0
+mflash bank $_FLASHNAME s3c2440 0x10000000 1b 0
@end example
Example for pxa270 mflash where @var{RST pin} is GPIO 43:
@example
-mflash bank pxa270 0x08000000 43 0
+mflash bank $_FLASHNAME pxa270 0x08000000 43 0
@end example
@end deffn
@item @b{LPC2000 Flash} In the configuration file in the section where flash device configurations
are described, there is a parameter for specifying the clock frequency
-for LPC2000 internal flash devices (e.g. @option{flash bank lpc2000
-0x0 0x40000 0 0 0 lpc2000_v1 14746 calc_checksum}), which must be
+for LPC2000 internal flash devices (e.g. @option{flash bank $_FLASHNAME lpc2000
+0x0 0x40000 0 0 $_TARGETNAME lpc2000_v1 14746 calc_checksum}), which must be
specified in kilohertz. However, I do have a quartz crystal of a
frequency that contains fractions of kilohertz (e.g. 14,745,600 Hz,
i.e. 14,745.600 kHz). Is it possible to specify real numbers for the
projects / openocd / commitdiff