cfg: Beaglebone Support

Added support for the Beaglebone board based on the am335x processor
family.  After much trial and error, I was able to configure the
Icepick-D and connect to the processor, halt execution, and run a sample
program.  This is a unified config file (it doesn't use any include
statements) and further work needs to be done to split out the icepick-d
configuration to be more generic.

Change-Id: Ia1b8e9f01f56bd4f8c575ba3d0160c248583a15e
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Reviewed-on: http://openocd.zylin.com/471
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>

diff --git a/tcl/ti-beaglebone.cfg b/tcl/ti-beaglebone.cfg
new file mode 100644 (file)
index 0000000..c9a54b0
--- /dev/null
+++ b/tcl/ti-beaglebone.cfg
@@ -0,0 +1,92 @@
+interface ft2232
+#ft2232_device_desc "BeagleBone A"
+ft2232_layout xds100v2
+ft2232_vid_pid 0x0403 0xa6d0
+
+#jtag_rclk 10
+adapter_khz 1000
+
+if { [info exists CHIPNAME] } {
+   set _CHIPNAME $CHIPNAME
+} else {
+   set _CHIPNAME am335x
+}
+
+proc icepick_d_tapenable {jrc port} {
+       # select router
+       irscan $jrc 7 -endstate IRPAUSE
+       drscan $jrc 8 0x89 -endstate DRPAUSE
+
+       # set ip control
+       irscan $jrc 2 -endstate IRPAUSE
+       drscan $jrc 32 [expr 0xa0002108 + ($port << 24)] -endstate DRPAUSE
+
+       # for icepick_D
+       irscan $jrc 2 -endstate IRPAUSE
+       drscan $jrc 32 0xe0002008 -endstate DRPAUSE
+
+       irscan $jrc 0x3F -endstate RUN/IDLE
+       runtest 10
+}
+
+#
+# M3 DAP
+#
+if { [info exists M3_DAP_TAPID] } {
+       set _M3_DAP_TAPID $M3_DAP_TAPID
+} else {
+       set _M3_DAP_TAPID 0x4b6b902f
+}
+jtag newtap $_CHIPNAME m3_dap -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_M3_DAP_TAPID -disable
+jtag configure $_CHIPNAME.m3_dap -event tap-enable "icepick_d_tapenable $_CHIPNAME.jrc 11"
+
+#
+# Main DAP
+#
+if { [info exists DAP_TAPID ] } {
+   set _DAP_TAPID $DAP_TAPID
+} else {
+   set _DAP_TAPID 0x4b6b902f
+}
+jtag newtap $_CHIPNAME dap -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_DAP_TAPID -disable
+jtag configure $_CHIPNAME.dap -event tap-enable "icepick_d_tapenable $_CHIPNAME.jrc 12"
+
+#
+# ICEpick-D (JTAG route controller)
+#
+if { [info exists JRC_TAPID ] } {
+   set _JRC_TAPID $JRC_TAPID
+} else {
+   set _JRC_TAPID 0x0b94402f
+}
+jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID
+jtag configure $_CHIPNAME.jrc -event setup "jtag tapenable $_CHIPNAME.dap"
+# some TCK tycles are required to activate the DEBUG power domain
+jtag configure $_CHIPNAME.jrc -event post-reset "runtest 100"
+
+#
+# Cortex A8 target
+#
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_a8 -chain-position $_CHIPNAME.dap -dbgbase 0x80001000
+
+# SRAM: 64K at 0x4030.0000; use the first 16K
+$_TARGETNAME configure -work-area-phys 0x40300000 -work-area-size 0x4000
+
+$_TARGETNAME configure -event reset-assert "am335x_dbginit $_TARGETNAME"
+$_TARGETNAME configure -event reset-assert-post "am335x_dbginit $_TARGETNAME"
+
+$_TARGETNAME configure -event gdb-attach {
+   global _TARGETNAME
+   am335x_dbginit $_TARGETNAME
+   echo "Halting target"
+   halt
+}
+
+# Run this to enable invasive debugging.  This is run automatically in the
+# reset sequence.
+proc am335x_dbginit {target} {
+   # General Cortex A8 debug initialisation
+   cortex_a8 dbginit
+}
+