From: Reinhard Arlt Date: Tue, 13 Apr 2010 07:59:09 +0000 (+0200) Subject: 74xx_7xx: CPCI750: Add ECC support on esd CPCI-CPU/750 board X-Git-Tag: v2010.06-rc1~34 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=0738e24e2c1d95bb94455d44485dc5d7b9c9d707;p=u-boot 74xx_7xx: CPCI750: Add ECC support on esd CPCI-CPU/750 board Add ECC support for DDR RAM for MV64360 on esd CPCI-CPU/750 board. This patch also adds the "pldver" command to display the CPLD revision. Signed-off-by: Reinhard Arlt Signed-off-by: Stefan Roese --- diff --git a/board/esd/cpci750/cpci750.c b/board/esd/cpci750/cpci750.c index 2ae4cbd6c0..a199d46182 100644 --- a/board/esd/cpci750/cpci750.c +++ b/board/esd/cpci750/cpci750.c @@ -1090,3 +1090,15 @@ U_BOOT_CMD( "Show Marvell strapping register", "Show Marvell strapping register (ResetSampleLow ResetSampleHigh)" ); + +int do_pldver(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + printf("PLD version:0x%02x\n", in_8((void *)CONFIG_SYS_PLD_VER)); + + return 0; +} + +U_BOOT_CMD( + pldver, 1, 1, do_pldver, + "Show PLD version", + "Show PLD version)"); diff --git a/board/esd/cpci750/sdram_init.c b/board/esd/cpci750/sdram_init.c index 4c03630fb5..5347958085 100644 --- a/board/esd/cpci750/sdram_init.c +++ b/board/esd/cpci750/sdram_init.c @@ -538,14 +538,14 @@ static int check_dimm (uchar slot, AUX_MEM_DIMM_INFO * dimmInfo) break; /*------------------------------------------------------------------------------------------------------------------------------*/ -#ifdef CONFIG_ECC +#ifdef CONFIG_MV64360_ECC case 11: /* Error Check Type */ dimmInfo->errorCheckType = data[i]; DP (printf ("Error Check Type (0=NONE): %d\n", dimmInfo->errorCheckType)); break; -#endif +#endif /* of ifdef CONFIG_MV64360_ECC */ /*------------------------------------------------------------------------------------------------------------------------------*/ case 12: /* Refresh Interval */ @@ -1254,6 +1254,7 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info) ulong tmp; ulong tmp_sdram_mode = 0; /* 0x141c */ ulong tmp_dunit_control_low = 0; /* 0x1404 */ + uint sdram_config_reg = CONFIG_SYS_SDRAM_CONFIG; int i; /* sanity checking */ @@ -1269,7 +1270,6 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info) DP (printf ("Module is registered, but we do not support registered Modules !!!\n")); - /* delay line */ set_dfcdlInit (); /* may be its not needed */ DP (printf ("Delay line set done\n")); @@ -1281,8 +1281,16 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info) ("\n*** SDRAM_OPERATION 1418: Module still busy ... please wait... ***\n")); } +#ifdef CONFIG_MV64360_ECC + if ((info->errorCheckType == 0x2) && (CPCI750_ECC_TEST)) { + /* DRAM has ECC, so turn it on */ + sdram_config_reg |= BIT18; + DP(printf("Enabling ECC\n")); + } +#endif /* of ifdef CONFIG_MV64360_ECC */ + /* SDRAM configuration */ - GT_REG_WRITE (SDRAM_CONFIG, 0x58200400); + GT_REG_WRITE(SDRAM_CONFIG, sdram_config_reg); DP (printf ("sdram_conf 0x1400: %08x\n", GTREGREAD (SDRAM_CONFIG))); /* SDRAM open pages controll keep open as much as I can */ @@ -1598,7 +1606,84 @@ dram_size(long int *base, long int maxsize) return maxsize; } -/* ------------------------------------------------------------------------- */ +#ifdef CONFIG_MV64360_ECC +/* + * mv_dma_is_channel_active: + * Checks if a engine is busy. + */ +int mv_dma_is_channel_active(int engine) +{ + ulong data; + + data = GTREGREAD(MV64360_DMA_CHANNEL0_CONTROL + 4 * engine); + if (data & BIT14) /* activity status */ + return 1; + + return 0; +} + +/* + * mv_dma_set_memory_space: + * Set a DMA memory window for the DMA's address decoding map. + */ +int mv_dma_set_memory_space(ulong mem_space, ulong mem_space_target, + ulong mem_space_attr, ulong base_address, + ulong size) +{ + ulong temp; + + /* The base address must be aligned to the size. */ + if (base_address % size != 0) + return 0; + + if (size >= 0x10000) { + size &= 0xffff0000; + base_address = (base_address & 0xffff0000); + /* Set the new attributes */ + GT_REG_WRITE(MV64360_DMA_BASE_ADDR_REG0 + mem_space * 8, + (base_address | mem_space_target | + mem_space_attr)); + GT_REG_WRITE((MV64360_DMA_SIZE_REG0 + mem_space * 8), + (size - 1) & 0xffff0000); + temp = GTREGREAD(MV64360_DMA_BASE_ADDR_ENABLE_REG); + GT_REG_WRITE(DMA_BASE_ADDR_ENABLE_REG, + (temp & ~(BIT0 << mem_space))); + return 1; + } + + return 0; +} + + +/* + * mv_dma_transfer: + * Transfer data from source_addr to dest_addr on one of the 4 DMA channels. + */ +int mv_dma_transfer(int engine, ulong source_addr, + ulong dest_addr, ulong bytes, ulong command) +{ + ulong eng_off_reg; /* Engine Offset Register */ + + if (bytes > 0xffff) + command = command | BIT31; /* DMA_16M_DESCRIPTOR_MODE */ + + command = command | ((command >> 6) & 0x7); + eng_off_reg = engine * 4; + GT_REG_WRITE(MV64360_DMA_CHANNEL0_BYTE_COUNT + eng_off_reg, + bytes); + GT_REG_WRITE(MV64360_DMA_CHANNEL0_SOURCE_ADDR + eng_off_reg, + source_addr); + GT_REG_WRITE(MV64360_DMA_CHANNEL0_DESTINATION_ADDR + eng_off_reg, + dest_addr); + command |= BIT12 /* DMA_CHANNEL_ENABLE */ + | BIT9; /* DMA_NON_CHAIN_MODE */ + + /* Activate DMA engine By writting to mv_dma_control_register */ + GT_REG_WRITE(MV64360_DMA_CHANNEL0_CONTROL + eng_off_reg, command); + + return 1; +} +#endif /* of ifdef CONFIG_MV64360_ECC */ /* ppcboot interface function to SDRAM init - this is where all the * controlling logic happens */ @@ -1607,10 +1692,13 @@ initdram(int board_type) { int s0 = 0, s1 = 0; int checkbank[4] = { [0 ... 3] = 0 }; - ulong bank_no, realsize, total, check; + ulong realsize, total, check; AUX_MEM_DIMM_INFO dimmInfo1; AUX_MEM_DIMM_INFO dimmInfo2; - int nhr; + int bank_no, nhr; +#ifdef CONFIG_MV64360_ECC + ulong dest, mem_space_attr; +#endif /* of ifdef CONFIG_MV64360_ECC */ /* first, use the SPD to get info about the SDRAM/ DDRRAM */ @@ -1668,6 +1756,28 @@ initdram(int board_type) realsize = dram_size((long int *)total, check); memory_map_bank(bank_no, total, realsize); +#ifdef CONFIG_MV64360_ECC + if (((dimmInfo1.errorCheckType != 0) && + ((dimmInfo2.errorCheckType != 0) || + (dimmInfo2.numOfModuleBanks == 0))) && + (CPCI750_ECC_TEST)) { + printf("ECC Initialization of Bank %d:", bank_no); + mem_space_attr = ((~(BIT0 << bank_no)) & 0xf) << 8; + mv_dma_set_memory_space(0, 0, mem_space_attr, total, + realsize); + for (dest = total; dest < total + realsize; + dest += _8M) { + mv_dma_transfer(0, total, dest, _8M, + BIT8 | /* DMA_DTL_128BYTES */ + BIT3 | /* DMA_HOLD_SOURCE_ADDR */ + BIT11); /* DMA_BLOCK_TRANSFER_MODE */ + while (mv_dma_is_channel_active(0)) + ; + } + printf(" PASS\n"); + } +#endif /* of ifdef CONFIG_MV64360_ECC */ + total += realsize; } @@ -1700,3 +1810,30 @@ int set_dfcdlInit (void) return (0); } + +int do_show_ecc(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + unsigned int ecc_counter; + unsigned int ecc_addr; + + GT_REG_READ(0x1458, &ecc_counter); + GT_REG_READ(0x1450, &ecc_addr); + GT_REG_WRITE(0x1450, 0); + + printf("Error Counter since Reset: %8d\n", ecc_counter); + printf("Last error address :0x%08x (" , ecc_addr & 0xfffffff8); + if (ecc_addr & 0x01) + printf("double"); + else + printf("single"); + printf(" bit) at DDR-RAM CS#%d\n", ((ecc_addr & 0x6) >> 1)); + + return 0; +} + + +U_BOOT_CMD( + show_ecc, 1, 1, do_show_ecc, + "Show Marvell MV64360 ECC Info", + "Show Marvell MV64360 ECC Counter and last error." +); diff --git a/include/configs/CPCI750.h b/include/configs/CPCI750.h index d516c3cb81..1c8c68b3e4 100644 --- a/include/configs/CPCI750.h +++ b/include/configs/CPCI750.h @@ -59,7 +59,7 @@ #define CONFIG_BAUDRATE 9600 /* console baudrate = 9600 */ -#undef CONFIG_ECC /* enable ECC support */ +#define CONFIG_MV64360_ECC /* enable ECC support */ #define CONFIG_HIGH_BATS 1 /* High BATs supported */ @@ -628,5 +628,7 @@ #define CONFIG_SYS_BOARD_ASM_INIT 1 #define CPCI750_SLAVE_TEST (((in8(0xf0300000) & 0x80) == 0) ? 0 : 1) +#define CPCI750_ECC_TEST (((in8(0xf0300000) & 0x02) == 0) ? 1 : 0) +#define CONFIG_SYS_PLD_VER 0xf0e00000 #endif /* __CONFIG_H */