From: R. Diez Date: Sat, 8 Jun 2013 14:07:28 +0000 (+0200) Subject: Bus Pirate driver: Small assorted fixes. X-Git-Tag: v0.8.0-rc1~395 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=0910f1a50744c87a87417d71075b274ff61417fa;p=openocd Bus Pirate driver: Small assorted fixes. Fixes are: - Discard any stale data from the previous connection. - Disable CR/LF translation on the (virtual USB) serial port. - Increase the average USB packet size. The 1 KiB buffer was underutilised. - Option "buspirate_speed fast" now works out of the box. - Some extra comments, error checking, etc. Change-Id: I72c49d943a8ce9c5e5d1644ef90cb1482f93c618 Signed-off-by: R. Diez Reviewed-on: http://openocd.zylin.com/1437 Tested-by: jenkins Reviewed-by: Spencer Oliver --- diff --git a/src/jtag/drivers/buspirate.c b/src/jtag/drivers/buspirate.c index 34dcd2b5..12d34b9d 100644 --- a/src/jtag/drivers/buspirate.c +++ b/src/jtag/drivers/buspirate.c @@ -1,6 +1,7 @@ /*************************************************************************** * Copyright (C) 2010 by Michal Demin * * based on usbprog.c and arm-jtag-ew.c * + * Several fixes by R. Diez in 2013. * * * * This program is free software; you can redistribute it and/or modify * * it under the terms of the GNU General Public License as published by * @@ -81,6 +82,9 @@ enum { SERIAL_FAST = 1 }; +static const cc_t SHORT_TIMEOUT = 1; /* Must be at least 1. */ +static const cc_t NORMAL_TIMEOUT = 10; + static int buspirate_fd = -1; static int buspirate_pinmode = MODE_JTAG_OD; static int buspirate_baudrate = SERIAL_NORMAL; @@ -88,6 +92,9 @@ static int buspirate_vreg; static int buspirate_pullup; static char *buspirate_port; +static enum tap_state last_tap_state = TAP_RESET; + + /* TAP interface */ static void buspirate_tap_init(void); static int buspirate_tap_execute(void); @@ -109,7 +116,7 @@ static void buspirate_jtag_get_adcs(int); /* low level HW communication interface */ static int buspirate_serial_open(char *port); -static int buspirate_serial_setspeed(int fd, char speed); +static int buspirate_serial_setspeed(int fd, char speed, cc_t timeout); static int buspirate_serial_write(int fd, char *buf, int size); static int buspirate_serial_read(int fd, char *buf, int size); static void buspirate_serial_close(int fd); @@ -196,6 +203,54 @@ static int buspirate_execute_queue(void) return buspirate_tap_execute(); } + +/* Returns true if successful, false if error. */ + +static bool read_and_discard_all_data(const int fd) +{ + /* LOG_INFO("Discarding any stale data from a previous connection..."); */ + + bool was_msg_already_printed = false; + + for ( ; ; ) { + char buffer[1024]; /* Any size will do, it's a trade-off between stack size and performance. */ + + const ssize_t read_count = read(fd, buffer, sizeof(buffer)); + + if (read_count == 0) { + /* This is the "end of file" or "connection closed at the other end" condition. */ + return true; + } + + if (read_count > 0) { + if (!was_msg_already_printed) { + LOG_INFO("Some stale data from a previous connection was discarded."); + was_msg_already_printed = true; + } + + continue; + } + + assert(read_count == -1); /* According to the specification. */ + + const int errno_code = errno; + + if (errno_code == EINTR) + continue; + + if (errno_code == EAGAIN || + errno_code == EWOULDBLOCK) { + /* We know that the file descriptor has been opened with O_NONBLOCK or O_NDELAY, + and these codes mean that there is no data to read at present. */ + return true; + } + + /* Some other error has occurred. */ + return false; + } +} + + static int buspirate_init(void) { if (buspirate_port == NULL) { @@ -209,7 +264,33 @@ static int buspirate_init(void) return ERROR_JTAG_INIT_FAILED; } - buspirate_serial_setspeed(buspirate_fd, SERIAL_NORMAL); + /* The Operating System or the device itself may deliver stale data from the last connection, + so discard all available bytes right after the new connection has been established. + After all, we are implementing here a master/slave protocol, so the slave should have nothing + to say until the master sends the first command. + + In the past, there was a tcflush() call in buspirate_serial_setspeed(), but that + was not enough. I guess you must actively read from the serial port to trigger any + data collection from the device and/or lower USB layers. If you disable the serial port + read timeout (if you set SHORT_TIMEOUT to 0), then the discarding does not work any more. + + Note that we are lowering the serial port timeout for this first read operation, + otherwise the normal initialisation would be delayed for too long. */ + + if (-1 == buspirate_serial_setspeed(buspirate_fd, SERIAL_NORMAL, SHORT_TIMEOUT)) { + LOG_ERROR("Error configuring the serial port."); + return ERROR_JTAG_INIT_FAILED; + } + + if (!read_and_discard_all_data(buspirate_fd)) { + LOG_ERROR("Error while attempting to discard any stale data right after establishing the connection."); + return ERROR_JTAG_INIT_FAILED; + } + + if (-1 == buspirate_serial_setspeed(buspirate_fd, SERIAL_NORMAL, NORMAL_TIMEOUT)) { + LOG_ERROR("Error configuring the serial port."); + return ERROR_JTAG_INIT_FAILED; + } buspirate_jtag_enable(buspirate_fd); @@ -524,8 +605,20 @@ static void buspirate_scan(bool ir_scan, enum scan_type type, /************************* TAP related stuff **********/ +/* This buffer size matches the maximum CMD_TAP_SHIFT bit length in the Bus Pirate firmware, + look for constant 0x2000 in OpenOCD.c . */ #define BUSPIRATE_BUFFER_SIZE 1024 -#define BUSPIRATE_MAX_PENDING_SCANS 32 + +/* The old value of 32 scans was not enough to achieve near 100% utilisation ratio + for the current BUSPIRATE_BUFFER_SIZE value of 1024. + With 128 scans I am getting full USB 2.0 high speed packets (512 bytes long) when + using the JtagDue firmware on the Arduino Due instead of the Bus Pirate, which + amounts approximately to a 10% overall speed gain. Bigger packets should also + benefit the Bus Pirate, but the speed difference is much smaller. + Unfortunately, each 512-byte packet is followed by a 329-byte one, which is not ideal. + However, increasing BUSPIRATE_BUFFER_SIZE for the benefit of the JtagDue would + make it incompatible with the Bus Pirate firmware. */ +#define BUSPIRATE_MAX_PENDING_SCANS 128 static char tms_chain[BUSPIRATE_BUFFER_SIZE]; /* send */ static char tdi_chain[BUSPIRATE_BUFFER_SIZE]; /* send */ @@ -551,6 +644,8 @@ static void buspirate_tap_init(void) static int buspirate_tap_execute(void) { + static const int CMD_TAP_SHIFT_HEADER_LEN = 3; + char tmp[4096]; uint8_t *in_buf; int i; @@ -564,13 +659,13 @@ static int buspirate_tap_execute(void) LOG_DEBUG("executing tap num bits = %i scans = %i", tap_chain_index, tap_pending_scans_num); - bytes_to_send = (tap_chain_index+7) / 8; + bytes_to_send = DIV_ROUND_UP(tap_chain_index, 8); tmp[0] = CMD_TAP_SHIFT; /* this command expects number of bits */ tmp[1] = (char)(tap_chain_index >> 8); /* high */ tmp[2] = (char)(tap_chain_index); /* low */ - fill_index = 3; + fill_index = CMD_TAP_SHIFT_HEADER_LEN; for (i = 0; i < bytes_to_send; i++) { tmp[fill_index] = tdi_chain[i]; fill_index++; @@ -578,18 +673,26 @@ static int buspirate_tap_execute(void) fill_index++; } - ret = buspirate_serial_write(buspirate_fd, tmp, 3 + bytes_to_send*2); - if (ret != bytes_to_send*2+3) { + /* jlink.c calls the routine below, which may be useful for debugging purposes. + For example, enabling this allows you to compare the log outputs from jlink.c + and from this module for JTAG development or troubleshooting purposes. */ + if (false) { + last_tap_state = jtag_debug_state_machine(tms_chain, tdi_chain, + tap_chain_index, last_tap_state); + } + + ret = buspirate_serial_write(buspirate_fd, tmp, CMD_TAP_SHIFT_HEADER_LEN + bytes_to_send*2); + if (ret != bytes_to_send*2+CMD_TAP_SHIFT_HEADER_LEN) { LOG_ERROR("error writing :("); return ERROR_JTAG_DEVICE_ERROR; } - ret = buspirate_serial_read(buspirate_fd, tmp, bytes_to_send + 3); - if (ret != bytes_to_send + 3) { + ret = buspirate_serial_read(buspirate_fd, tmp, bytes_to_send + CMD_TAP_SHIFT_HEADER_LEN); + if (ret != bytes_to_send + CMD_TAP_SHIFT_HEADER_LEN) { LOG_ERROR("error reading"); return ERROR_FAIL; } - in_buf = (uint8_t *)(&tmp[3]); + in_buf = (uint8_t *)(&tmp[CMD_TAP_SHIFT_HEADER_LEN]); /* parse the scans */ for (i = 0; i < tap_pending_scans_num; i++) { @@ -609,8 +712,7 @@ static int buspirate_tap_execute(void) free(buffer); } - tap_pending_scans_num = 0; - tap_chain_index = 0; + buspirate_tap_init(); return ERROR_OK; } @@ -634,6 +736,19 @@ static void buspirate_tap_append(int tms, int tdi) int bit_index = tap_chain_index % 8; uint8_t bit = 1 << bit_index; + if (0 == bit_index) { + /* Let's say that the TAP shift operation wants to shift 9 bits, + so we will be sending to the Bus Pirate a bit count of 9 but still + full 16 bits (2 bytes) of shift data. + If we don't clear all bits at this point, the last 7 bits will contain + random data from the last buffer contents, which is not pleasant to the eye. + Besides, the Bus Pirate (or some clone) may want to assert in debug builds + that, after consuming all significant data bits, the rest of them are zero. + Therefore, for aesthetic and for assert purposes, we clear all bits below. */ + tms_chain[chain_index] = 0; + tdi_chain[chain_index] = 0; + } + if (tms) tms_chain[chain_index] |= bit; else @@ -645,9 +760,13 @@ static void buspirate_tap_append(int tms, int tdi) tdi_chain[chain_index] &= ~bit; tap_chain_index++; - } else + } else { LOG_ERROR("tap_chain overflow, bad things will happen"); - + /* Exit abruptly, like jlink.c does. After a buffer overflow we don't want + to carry on, as data will be corrupt. Another option would be to return + some error code at this point. */ + exit(-1); + } } static void buspirate_tap_append_scan(int length, uint8_t *buffer, @@ -770,7 +889,10 @@ static void buspirate_jtag_set_speed(int fd, char speed) buspirate_jtag_command(fd, tmp, 2); /* here the adapter changes speed, we need follow */ - buspirate_serial_setspeed(fd, speed); + if (-1 == buspirate_serial_setspeed(fd, speed, NORMAL_TIMEOUT)) { + LOG_ERROR("Error configuring the serial port."); + exit(-1); + } buspirate_serial_write(fd, ack, 2); ret = buspirate_serial_read(fd, tmp, 2); @@ -779,7 +901,7 @@ static void buspirate_jtag_set_speed(int fd, char speed) exit(-1); } if ((tmp[0] != CMD_UART_SPEED) || (tmp[1] != speed)) { - LOG_ERROR("Buspirate did not reply as expected"); + LOG_ERROR("Buspirate did not reply as expected to the speed change command"); exit(-1); } LOG_INFO("Buspirate switched to %s mode", @@ -865,28 +987,50 @@ static int buspirate_serial_open(char *port) return fd; } -static int buspirate_serial_setspeed(int fd, char speed) + +/* Returns -1 on error. */ + +static int buspirate_serial_setspeed(int fd, char speed, cc_t timeout) { struct termios t_opt; speed_t baud = (speed == SERIAL_FAST) ? B1000000 : B115200; /* set the serial port parameters */ fcntl(fd, F_SETFL, 0); - tcgetattr(fd, &t_opt); - cfsetispeed(&t_opt, baud); - cfsetospeed(&t_opt, baud); + if (0 != tcgetattr(fd, &t_opt)) + return -1; + + if (0 != cfsetispeed(&t_opt, baud)) + return -1; + + if (0 != cfsetospeed(&t_opt, baud)) + return -1; + t_opt.c_cflag |= (CLOCAL | CREAD); t_opt.c_cflag &= ~PARENB; t_opt.c_cflag &= ~CSTOPB; t_opt.c_cflag &= ~CSIZE; t_opt.c_cflag |= CS8; t_opt.c_lflag &= ~(ICANON | ECHO | ECHOE | ISIG); - t_opt.c_iflag &= ~(IXON | IXOFF | IXANY); + + /* The serial port may have been configured for human interaction with + the Bus Pirate console, but OpenOCD is going to use a binary protocol, + so make sure to turn off any CR/LF translation and the like. */ + t_opt.c_iflag &= ~(IXON | IXOFF | IXANY | INLCR | ICRNL); + t_opt.c_oflag &= ~OPOST; t_opt.c_cc[VMIN] = 0; - t_opt.c_cc[VTIME] = 10; - tcflush(fd, TCIFLUSH); - tcsetattr(fd, TCSANOW, &t_opt); + t_opt.c_cc[VTIME] = timeout; + + /* Note that, in the past, TCSANOW was used below instead of TCSADRAIN, + and CMD_UART_SPEED did not work properly then, at least with + the Bus Pirate v3.5 (USB). */ + if (0 != tcsetattr(fd, TCSADRAIN, &t_opt)) { + /* According to the Linux documentation, this is actually not enough + to detect errors, you need to call tcgetattr() and check that + all changes have been performed successfully. */ + return -1; + } return 0; }