From: Matt Sealey Date: Thu, 23 Aug 2012 04:52:33 +0000 (+0000) Subject: efikamx: refine USB support X-Git-Tag: v2012.10-rc1~2^2^2~18 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=0d7d3830984012a8209bbf497f92add652082afb;p=u-boot efikamx: refine USB support Because of the way USB pad settings are handled it doesn't make sense to be able to build the Efika MX board support without CONFIG_CMD_USB turned on. So, we change the build to always compile in USB support. We do not need to check for CONFIG_CMD_USB like we do with CONFIG_MXC_SPI since the USB subsystem will error out of the compile for us. Additionally, the following behaviors have changed; * Smartbook "preboot" should not set input and output to USB keyboard as there is no display support * board_eth_init is implemented such that it does not cause U-Boot to report an explicit failure ("CPU Net Initialization Failed"). Since Ethernet is implemented via USB (fixed on Smarttop, pluggable on Smartbook, and handled by "usb start") - the warning that is left ("No ethernet found") is perfectly reasonable at the point it is printed since the USB system hasn't been started and nothing has been probed yet. Signed-off-by: Matt Sealey Cc: Stefano Babic Cc: Marek Vasut --- diff --git a/board/genesi/mx51_efikamx/Makefile b/board/genesi/mx51_efikamx/Makefile index bd2174fec3..f95356f16d 100644 --- a/board/genesi/mx51_efikamx/Makefile +++ b/board/genesi/mx51_efikamx/Makefile @@ -27,11 +27,7 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o -COBJS := efikamx.o - -ifdef CONFIG_CMD_USB -COBJS += efikamx-usb.o -endif +COBJS := efikamx.o efikamx-usb.o SRCS := $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/board/genesi/mx51_efikamx/efikamx-usb.c b/board/genesi/mx51_efikamx/efikamx-usb.c index e9273d027a..cf020c35cb 100644 --- a/board/genesi/mx51_efikamx/efikamx-usb.c +++ b/board/genesi/mx51_efikamx/efikamx-usb.c @@ -214,3 +214,15 @@ void board_ehci_hcd_postinit(struct usb_ehci *ehci, int port) if (port) mdelay(10); } + +/* + * Ethernet on the Smarttop is on the USB bus. Rather than give an error about + * "CPU Net Initialization Failed", just pass this test since no other settings + * are required. Smartbook doesn't have built-in Ethernet but we will let it + * pass anyway considering someone may have plugged in a USB stick and all + * they need to do is run "usb start". + */ +int board_eth_init(bd_t *bis) +{ + return 0; +} diff --git a/board/genesi/mx51_efikamx/efikamx.c b/board/genesi/mx51_efikamx/efikamx.c index 6d98c94db9..cfd2e938b9 100644 --- a/board/genesi/mx51_efikamx/efikamx.c +++ b/board/genesi/mx51_efikamx/efikamx.c @@ -492,9 +492,6 @@ int board_late_init(void) ARRAY_SIZE(efikamx_pata_pads)); setup_iomux_usb(); - if (machine_is_efikasb()) - setenv("preboot", "usb reset ; setenv stdin usbkbd\0"); - return 0; }