From: wdenk Date: Mon, 19 Aug 2002 11:57:05 +0000 (+0000) Subject: Initial revision X-Git-Tag: LABEL_2006_03_12_0025~1107 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=0f8c9768ff83244c49857a0c79fe04e947f387ce;p=u-boot Initial revision --- diff --git a/include/configs/ADCIOP.h b/include/configs/ADCIOP.h new file mode 100644 index 0000000000..92b4482cb6 --- /dev/null +++ b/include/configs/ADCIOP.h @@ -0,0 +1,210 @@ +/* + * (C) Copyright 2001 + * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_IOP480 1 /* This is a IOP480 CPU */ +#define CONFIG_ADCIOP 1 /* ...on a ADCIOP board */ + +#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_CPUCLOCK 66 +#define CONFIG_BUSCLOCK (CONFIG_CPUCLOCK) + +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ +#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */ + +#undef CONFIG_BOOTARGS + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_PHY_ADDR 0 /* PHY address */ + +#define CONFIG_IPADDR 10.0.18.222 +#define CONFIG_SERVERIP 10.0.18.190 + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_DHCP | \ + CFG_CMD_IRQ | \ + CFG_CMD_ELF | \ + CFG_CMD_ASKENV ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +/* The following table includes the supported baudrates */ +#define CFG_BAUDRATE_TABLE \ + { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 } + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */ +#define CFG_INIT_RAM_END 0x0f00 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFFFD0000 +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size (width) */ +#define CFG_FLASH_ADDR0 0x0AA9 /* 1st address for flash config cycles */ +#define CFG_FLASH_ADDR1 0x0556 /* 2nd address for flash config cycles */ +/* + * The following defines are added for buggy IOP480 byte interface. + * All other boards should use the standard values (CPCI405 etc.) + */ +#define CFG_FLASH_READ0 0x0002 /* 0 is standard */ +#define CFG_FLASH_READ1 0x0000 /* 1 is standard */ +#define CFG_FLASH_READ2 0x0004 /* 2 is standard */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +#if 1 /* Use NVRAM for environment variables */ +/*----------------------------------------------------------------------- + * NVRAM organization + */ +#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ +#define CFG_NVRAM_BASE_ADDR 0x10000000 /* NVRAM base address */ +#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */ +#define CFG_ENV_SIZE 0x0400 /* Size of Environment vars */ +#define CFG_ENV_ADDR \ + (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ +#define CFG_NVRAM_VXWORKS_OFFS 0x7800 /* Offset for VxWorks eth-addr */ + +#else /* Use FLASH for environment variables */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ + +#define CFG_ENV_SECT_SIZE 0x8000 /* see README - env sector total size */ + +#endif + +/*----------------------------------------------------------------------- + * PCI stuff + */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP + +#define CONFIG_NET_MULTI /* Multi ethernet cards support */ + +#define CONFIG_TULIP + +#define CFG_ETH_DEV_FN 0x0000 +#define CFG_ETH_IOBASE 0x0fff0000 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 2048 /* For PLX IOP480 */ +#define CFG_CACHELINE_SIZE 16 /* For IBM 401/403 CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0xFFE00000 /* FLASH bank #1 */ + + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/CPCI440.h b/include/configs/CPCI440.h new file mode 100644 index 0000000000..04ce99dfa1 --- /dev/null +++ b/include/configs/CPCI440.h @@ -0,0 +1,287 @@ +/* + * (C) Copyright 2002 + * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * board/config_CPCI440.h - configuration for esd CPCI-440 board + ***********************************************************************/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_EBONY 1 /* Board is ebony */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ +#undef CFG_DRAM_TEST /* Disable-takes long time! */ +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */ +#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ +#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ +#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ + +#define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000) +#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000) + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer (placed in internal SRAM) + *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ + +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 192 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#undef CFG_EXT_SERIAL_CLOCK /* (1843200 * 6) / * Ext clk @ 11.059 MHz */ +#define CONFIG_BAUDRATE 9600 + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400} + +/*----------------------------------------------------------------------- + * NVRAM/RTC + * + * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located. + * The DS1743 code assumes this condition (i.e. -- it assumes the base + * address for the RTC registers is: + * + * CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE + * + *----------------------------------------------------------------------*/ +#define CFG_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs */ +#define CONFIG_RTC_DS174x 1 /* DS1743 RTC */ + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#if 1 /* test-only */ + +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_FLASH_INCREMENT 0 /* there is only one bank */ +#define CFG_FLASH_PROTECTION 1 /* use hardware protection */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#undef CFG_FLASH_BASE +#define CFG_FLASH_BASE 0xFF800000 /* test-only...*/ + +#else /* test-only */ + +#define CFG_MAX_FLASH_BANKS 3 /* number of banks */ +#define CFG_MAX_FLASH_SECT 32 /* sectors per device */ + +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#endif + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +#if 0 /* test-only */ +#define CFG_ENV_IS_IN_NVRAM 1 /* Environment uses NVRAM */ +#undef CFG_ENV_IS_IN_FLASH /* ... not in flash */ +#undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ + +#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */ +#define CFG_ENV_ADDR \ + (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) +#else + +#if 0 /* test-only */ +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CFG_ENV_OFFSET 0x010 /* environment starts at the beginning of the EEPROM */ +#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ + /* total size of a CAT24WC16 is 2048 bytes */ +#else +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#endif + +/*----------------------------------------------------------------------- + * I2C EEPROM (CAT24WC16) for environment + */ +#define CONFIG_HARD_I2C /* I2c with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ + /* 16 byte page write mode using*/ + /* last 4 bits of the address */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CFG_EEPROM_PAGE_WRITE_ENABLE + +#endif + +#define CONFIG_BOOTARGS "root=/dev/hda1 " +#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */ +#define CONFIG_BOOTDELAY -1 /* disable autoboot */ +#define CONFIG_BAUDRATE 9600 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 1 /* PHY address */ + +#if 0 /* test-only */ +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_IRQ | \ + CFG_CMD_I2C | \ + CFG_CMD_KGDB | \ + CFG_CMD_DHCP | \ + CFG_CMD_DATE | \ + CFG_CMD_BEDBUG | \ + CFG_CMD_ELF ) +#else +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_IRQ | \ + CFG_CMD_ELF | \ + CFG_CMD_DATE | \ + CFG_CMD_I2C | \ + CFG_CMD_EEPROM ) +/* test-only: support fehlt bisher... */ +/* CFG_CMD_IDE | \*/ +/* CFG_CMD_PCI | \*/ +#endif + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#undef CONFIG_SPD_EEPROM /* don't use SPD EEPROM for setup */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#if 0 /* test-only */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#endif + + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#if 0 +#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + /* resource configuration */ + +#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ +#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ +#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ +#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ +#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#endif + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 32768 /* For IBM 440 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + + +/* Configuration Port location */ +#define CONFIG_PORT_ADDR 0xF0000500 + +/*----------------------------------------------------------------------- + * Definitions for Serial Presence Detect EEPROM address + * (to get SDRAM settings) + */ +#define SPD_EEPROM_ADDRESS 0x50 + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ diff --git a/include/configs/CPU86.h b/include/configs/CPU86.h new file mode 100644 index 0000000000..ae8525f9b9 --- /dev/null +++ b/include/configs/CPU86.h @@ -0,0 +1,654 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ +#define CONFIG_CPU86 1 /* ...on a CPU86 board */ + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#undef CONFIG_CONS_ON_SMC /* define if console on SMC */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else*/ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ + +#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC) +#define CONFIG_BAUDRATE 230400 +#else +#define CONFIG_BAUDRATE 9600 +#endif + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + * + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */ + +#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1) + +/* + * - Rx-CLK is CLK11 + * - Tx-CLK is CLK12 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + +#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) + +/* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + +#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */ + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#define CONFIG_8260_CLKIN 64000000 /* in Hz */ + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_PREBOOT \ + "echo; " \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS; " \ + "echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +/*----------------------------------------------------------------------- + * I2C/EEPROM/RTC configuration + */ +#define CONFIG_SOFT_I2C /* Software I2C support enabled */ + +# define CFG_I2C_SPEED 50000 +# define CFG_I2C_SLAVE 0xFE +/* + * Software (bit-bang) I2C driver configuration + */ +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00010000) +#define I2C_TRISTATE (iop->pdir &= ~0x00010000) +#define I2C_READ ((iop->pdat & 0x00010000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CONFIG_RTC_PCF8563 +#define CFG_I2C_RTC_ADDR 0x51 + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/*----------------------------------------------------------------------- + * Disk-On-Chip configuration + */ + +#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ + +#define CFG_DOC_SUPPORT_2000 +#define CFG_DOC_SUPPORT_MILLENNIUM + +/*----------------------------------------------------------------------- + * Miscellaneous configuration options + */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_BEDBUG | \ + CFG_CMD_EEPROM | \ + CFG_CMD_DATE | \ + CFG_CMD_I2C | \ + CFG_CMD_DOC) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_RESET_ADDRESS 0xFFF00100 /* "bad" address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * Flash configuration + */ + +#define CFG_BOOTROM_BASE 0xFF800000 +#define CFG_BOOTROM_SIZE 0x00080000 +#define CFG_FLASH_BASE 0xFF000000 +#define CFG_FLASH_SIZE 0x00800000 + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max num of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ + +#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +/*----------------------------------------------------------------------- + * Other areas to be mapped + */ + +/* CS3: Dual ported SRAM */ +#define CFG_DPSRAM_BASE 0x40000000 +#define CFG_DPSRAM_SIZE 0x00020000 + +/* CS4: DiskOnChip */ +#define CFG_DOC_BASE 0xF4000000 +#define CFG_DOC_SIZE 0x00100000 + +/* CS5: FDC37C78 controller */ +#define CFG_FDC37C78_BASE 0xF1000000 +#define CFG_FDC37C78_SIZE 0x00100000 + +/* CS6: Board configuration registers */ +#define CFG_BCRS_BASE 0xF2000000 +#define CFG_BCRS_SIZE 0x00010000 + +/* CS7: VME Extended Access Range */ +#define CFG_VMEEAR_BASE 0x80000000 +#define CFG_VMEEAR_SIZE 0x01000000 + +/* CS8: VME Standard Access Range */ +#define CFG_VMESAR_BASE 0xFE000000 +#define CFG_VMESAR_SIZE 0x01000000 + +/* CS9: VME Short I/O Access Range */ +#define CFG_VMESIOAR_BASE 0xFD000000 +#define CFG_VMESIOAR_SIZE 0x01000000 + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CFG_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CFG_SIUMCR. + */ +#if defined(CONFIG_BOOT_ROM) +#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \ + HRCW_BPS01 | HRCW_CS10PC01) +#else +#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | HRCW_CS10PC01) +#endif + +/* no slaves so just fill with zeros */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xF0000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + * + * 60x SDRAM is mapped at CFG_SDRAM_BASE. + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT +#endif + +#if 0 +/* environment is in Flash */ +#define CFG_ENV_IS_IN_FLASH 1 +#ifdef CONFIG_BOOT_ROM +# define CFG_ENV_ADDR (CFG_FLASH_BASE+0x70000) +# define CFG_ENV_SIZE 0x10000 +# define CFG_ENV_SECT_SIZE 0x10000 +#endif +#else +/* environment is in EEPROM */ +#define CFG_ENV_IS_IN_EEPROM 1 +#define CFG_I2C_EEPROM_ADDR 0x58 /* EEPROM X24C16 */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CFG_ENV_OFFSET 0 +#define CFG_ENV_SIZE 2048 +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|\ + HID0_DCI|HID0_IFEM|HID0_ABE) +#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CFG_RMR RMR_CSRE + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define BCR_APD01 0x10000000 +#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */ + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#define CFG_SIUMCR (SIUMCR_BBD|SIUMCR_DPPC00|SIUMCR_APPC10|\ + SIUMCR_CS10PC01|SIUMCR_BCTLC10) + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + * Ensure DFBRG is Divide by 16 + */ +#define CFG_SCCR SCCR_DFBRG01 + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +#define CFG_MIN_AM_MASK 0xC0000000 +/*----------------------------------------------------------------------- + * MPTPR - Memory Refresh Timer Prescaler Register 10-18 + *----------------------------------------------------------------------- + */ +#define CFG_MPTPR 0x1F00 + +/*----------------------------------------------------------------------- + * PSRT - Refresh Timer Register 10-16 + *----------------------------------------------------------------------- + */ +#define CFG_PSRT 0x0f + +/*----------------------------------------------------------------------- + * PSRT - SDRAM Mode Register 10-10 + *----------------------------------------------------------------------- + */ + + /* SDRAM initialization values for 8-column chips + */ +#define CFG_OR2_8COL (CFG_MIN_AM_MASK |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A9 |\ + ORxS_NUMR_12) + +#define CFG_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\ + PSDMR_BSMA_A14_A16 |\ + PSDMR_SDA10_PBI0_A10 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_1W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) + + /* SDRAM initialization values for 9-column chips + */ +#define CFG_OR2_9COL (CFG_MIN_AM_MASK |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A7 |\ + ORxS_NUMR_13) + +#define CFG_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\ + PSDMR_BSMA_A13_A15 |\ + PSDMR_SDA10_PBI0_A9 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_1W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 8 bit Boot ROM + * 1 60x GPCM 64 bit FLASH + * 2 60x SDRAM 64 bit SDRAM + * + */ + +#define CFG_MRS_OFFS 0x00000000 + +#ifdef CONFIG_BOOT_ROM +/* Bank 0 - Boot ROM + */ +#define CFG_BR0_PRELIM ((CFG_BOOTROM_BASE & BRx_BA_MSK)|\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_BOOTROM_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxU_EHTR_8IDLE) + +/* Bank 1 - FLASH + */ +#define CFG_BR1_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxU_EHTR_8IDLE) + +#else /* CONFIG_BOOT_ROM */ +/* Bank 0 - FLASH + */ +#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxU_EHTR_8IDLE) + +/* Bank 1 - Boot ROM + */ +#define CFG_BR1_PRELIM ((CFG_BOOTROM_BASE & BRx_BA_MSK)|\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_BOOTROM_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxU_EHTR_8IDLE) + +#endif /* CONFIG_BOOT_ROM */ + + +/* Bank 2 - 60x bus SDRAM + */ +#ifndef CFG_RAMBOOT +#define CFG_BR2_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CFG_OR2_PRELIM CFG_OR2_9COL + +#define CFG_PSDMR CFG_PSDMR_9COL +#endif /* CFG_RAMBOOT */ + +/* Bank 3 - Dual Ported SRAM + */ +#define CFG_BR3_PRELIM ((CFG_DPSRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_16 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR3_PRELIM (P2SZ_TO_AM(CFG_DPSRAM_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_5_CLK |\ + ORxG_SETA) + +/* Bank 4 - DiskOnChip + */ +#define CFG_BR4_PRELIM ((CFG_DOC_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR4_PRELIM (P2SZ_TO_AM(CFG_DOC_SIZE) |\ + ORxG_ACS_DIV2 |\ + ORxG_SCY_5_CLK |\ + ORxU_EHTR_8IDLE) + +/* Bank 5 - FDC37C78 controller + */ +#define CFG_BR5_PRELIM ((CFG_FDC37C78_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR5_PRELIM (P2SZ_TO_AM(CFG_FDC37C78_SIZE) |\ + ORxG_ACS_DIV2 |\ + ORxG_SCY_8_CLK |\ + ORxU_EHTR_8IDLE) + +/* Bank 6 - Board control registers + */ +#define CFG_BR6_PRELIM ((CFG_BCRS_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR6_PRELIM (P2SZ_TO_AM(CFG_BCRS_SIZE) |\ + ORxG_CSNT |\ + ORxG_SCY_5_CLK) + +/* Bank 7 - VME Extended Access Range + */ +#define CFG_BR7_PRELIM ((CFG_VMEEAR_BASE & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR7_PRELIM (P2SZ_TO_AM(CFG_VMEEAR_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_5_CLK |\ + ORxG_SETA) + +/* Bank 8 - VME Standard Access Range + */ +#define CFG_BR8_PRELIM ((CFG_VMESAR_BASE & BRx_BA_MSK) |\ + BRx_PS_16 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR8_PRELIM (P2SZ_TO_AM(CFG_VMESAR_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_5_CLK |\ + ORxG_SETA) + +/* Bank 9 - VME Short I/O Access Range + */ +#define CFG_BR9_PRELIM ((CFG_VMESIOAR_BASE & BRx_BA_MSK) |\ + BRx_PS_16 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR9_PRELIM (P2SZ_TO_AM(CFG_VMESIOAR_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_5_CLK |\ + ORxG_SETA) + +#endif /* __CONFIG_H */ diff --git a/include/configs/DASA_SIM.h b/include/configs/DASA_SIM.h new file mode 100644 index 0000000000..85d8eb3e9e --- /dev/null +++ b/include/configs/DASA_SIM.h @@ -0,0 +1,209 @@ +/* + * (C) Copyright 2001 + * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_IOP480 1 /* This is a IOP480 CPU */ +#define CONFIG_DASA_SIM 1 /* ...on a DASA_SIM board */ + +#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_CPUCLOCK 66 +#define CONFIG_BUSCLOCK (CONFIG_CPUCLOCK) + +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ +#define CONFIG_BOOTCOMMAND "bootm ffe00000" /* autoboot command */ + +#undef CONFIG_BOOTARGS + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_IPADDR 10.0.18.222 +#define CONFIG_SERVERIP 10.0.18.190 + +#if 0 +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_DHCP | \ + CFG_CMD_IRQ | \ + CFG_CMD_BSP | \ + CFG_CMD_ASKENV | \ + CFG_CMD_ELF ) +#else +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_EEPROM | \ + CFG_CMD_BSP ) +#endif + +#if 0 /* Does not appear to be used?! If it is used, needs to be fixed */ +#define CONFIG_SOFT_I2C /* Software I2C support enabled */ +#endif +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +/* The following table includes the supported baudrates */ +#define CFG_BAUDRATE_TABLE \ + { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 } + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */ +#define CFG_INIT_RAM_END 0x0f00 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFFFD0000 +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 128 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size (width) */ +#define CFG_FLASH_ADDR0 0x0AA9 /* 1st address for flash config cycles */ +#define CFG_FLASH_ADDR1 0x0556 /* 2nd address for flash config cycles */ +/* + * The following defines are added for buggy IOP480 byte interface. + * All other boards should use the standard values (CPCI405 etc.) + */ +#define CFG_FLASH_READ0 0x0002 /* 0 is standard */ +#define CFG_FLASH_READ1 0x0000 /* 1 is standard */ +#define CFG_FLASH_READ2 0x0004 /* 2 is standard */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ + +#if 0 +#define CFG_ENV_SECT_SIZE 0x8000 /* see README - env sector total size */ +#else +#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */ +#endif + +/*----------------------------------------------------------------------- + * PCI stuff + */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP + +#define CONFIG_NET_MULTI /* Multi ethernet cards support */ + +#define CONFIG_TULIP + +#define CFG_ETH_DEV_FN 0x0000 +#define CFG_ETH_IOBASE 0x0fff0000 +#define CFG_PCI9054_DEV_FN 0x0800 +#define CFG_PCI9054_IOBASE 0x0eff0000 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 2048 /* For PLX IOP480 */ +#define CFG_CACHELINE_SIZE 16 /* For IBM 401/403 CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */ + + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/ESTEEM192E.h b/include/configs/ESTEEM192E.h new file mode 100644 index 0000000000..7a8fba62fb --- /dev/null +++ b/include/configs/ESTEEM192E.h @@ -0,0 +1,322 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC850 1 /* This is a MPC850 CPU */ +#define CONFIG_ESTEEM192E 1 /* ...on a EST ESTEEM192E */ + +#define CONFIG_FLASH_16BIT 1 /* Rom 16 bit data bus */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE + +#define MPC8XX_FACT 10 /* Multiply by 10 */ +#define MPC8XX_XIN 4915200 /* 4.915200 MHz in - ??? - XXX */ +#define CFG_PLPRCR_MF ((MPC8XX_FACT-1) << 20) +#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) /* 49,152,000 Hz */ + +#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ /* Force it - dont measure it */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_BAUDRATE 9600 +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif +#define CONFIG_BOOTCOMMAND "bootm 40030000" /* autoboot command */ + +#define CONFIG_BOOTARGS "root=/dev/ram rw ramdisk=8192 " \ + "ip=100.100.100.21:100.100.100.14:100.100.100.1:255.0.0.0 " +/* + * Miscellaneous configurable options + */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "BOOT: " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 8 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFF000000 + + /*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + + + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#ifdef DEBUG +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) + +/*----------------------------------------------------------------------- + * SUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) /* DBGC00 */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE) + +/* (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) */ + + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit - leave PLL multiplication factor unchanged ! + */ +#define CFG_PLPRCR (CFG_PLPRCR_MF | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +#define CFG_PCMCIA_INTERRUPT SIU_LEVEL6 + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 +/*#define CFG_DER 0x02002000 */ + + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ + +/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ +#define CFG_OR_TIMING_FLASH 0x00000160 + /*(OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ + OR_SCY_5_CLK | OR_EHTR) */ + +#define CFG_OR0_REMAP 0x80000160 /*(CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)*/ +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ( FLASH_BASE0_PRELIM | 0x00000801 ) + +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM CFG_OR0_PRELIM +#define CFG_BR1_PRELIM ( FLASH_BASE1_PRELIM | 0x00000801 ) + +/* + * BR2/3 and OR2/3 (SDRAM) + * + */ +#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_BASE3_PRELIM 0x04000000 /* SDRAM bank #1 */ +#define SDRAM_MAX_SIZE 0x02000000 /* max 32 MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM 0x00000A00 + +#define CFG_OR2_PRELIM 0xFC000E00 +#define CFG_BR2_PRELIM (SDRAM_BASE2_PRELIM | 0x00000081) + +#define CFG_OR3_PRELIM CFG_OR2_PRELIM +#define CFG_BR3_PRELIM (SDRAM_BASE3_PRELIM | 0x00000081) + + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */ + +/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL 0x18803112 +#define CFG_MAMR_9COL 0x18803112 /* same as 8 column because its just easier to port with*/ + + + +/* + * Internal Definitions + * + * Boot Flags + */ + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/FADS850SAR.h b/include/configs/FADS850SAR.h new file mode 100644 index 0000000000..a1041769ef --- /dev/null +++ b/include/configs/FADS850SAR.h @@ -0,0 +1,422 @@ + /* + * A collection of structures, addresses, and values associated with + * the Motorola 860T FADS board. Copied from the MBX stuff. + * Magnus Damm added defines for 8xxrom and extended bd_info. + * Helmut Buchsbaum added bitvalues for BCSRx + * + * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) + */ + +/* + * 1999-nov-26: The FADS is using the following physical memorymap: + * + * ff020000 -> ff02ffff : pcmcia + * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxrom + * ff000000 -> ff00ffff : IMAP internal in the cpu + * fe000000 -> ffnnnnnn : flash connected to CS0, setup by 8xxrom + * 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom + */ + +/* ------------------------------------------------------------------------- */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#include + +#define CONFIG_MPC850 1 +#define CONFIG_MPC850SAR 1 +#define CONFIG_FADS 1 + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 9600 + +#if 0 +#define MPC8XX_FACT 10 /* Multiply by 10 */ +#define MPC8XX_XIN 50000000 /* 50 MHz in */ +#else +#define MPC8XX_FACT 12 /* Multiply by 12 */ +#define MPC8XX_XIN 4000000 /* 4 MHz in */ +#endif +#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#if 1 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_BOOTCOMMAND "bootm 02880000" /* autoboot command */ +#define CONFIG_BOOTARGS " " + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#undef CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT ":>" /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00004000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00800000 /* 0 ... 8 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFF000000 +#define CFG_IMMR_SIZE ((uint)(64 * 1024)) + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Also NOTE that it doesn't mean SDRAM - it means MEMORY. + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x02800000 +#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ +#if 0 +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 128 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer * + * interrupt status bit - leave PLL multiplication factor unchanged ! + */ +#define CFG_PLPRCR (((MPC8XX_FACT-1) << 20) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + + /*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 + +/* Because of the way the 860 starts up and assigns CS0 the +* entire address space, we have to set the memory controller +* differently. Normally, you write the option register +* first, and then enable the chip select by writing the +* base register. For CS0, you must write the base register +* first, followed by the option register. +*/ + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ +/* the other CS:s are determined by looking at parameters in BCSRx */ + + +#define BCSR_ADDR ((uint) 0x02100000) +#define BCSR_SIZE ((uint)(64 * 1024)) + +#define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */ + +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFFE00000 /* OR addr mask */ + +/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/ +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) + +/* BCSRx - Board Control and Status Registers */ +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */ +#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V ) + + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */ + +/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +#define CFG_MAMR 0x13a01114 +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/* values according to the manual */ + + +#define PCMCIA_MEM_ADDR ((uint)0xff020000) +#define PCMCIA_MEM_SIZE ((uint)(64 * 1024)) + +#define BCSR0 ((uint) (BCSR_ADDR + 00)) +#define BCSR1 ((uint) (BCSR_ADDR + 0x04)) +#define BCSR2 ((uint) (BCSR_ADDR + 0x08)) +#define BCSR3 ((uint) (BCSR_ADDR + 0x0c)) +#define BCSR4 ((uint) (BCSR_ADDR + 0x10)) + +/* FADS bitvalues by Helmut Buchsbaum + * see MPC8xxADS User's Manual for a proper description + * of the following structures + */ + +#define BCSR0_ERB ((uint)0x80000000) +#define BCSR0_IP ((uint)0x40000000) +#define BCSR0_BDIS ((uint)0x10000000) +#define BCSR0_BPS_MASK ((uint)0x0C000000) +#define BCSR0_ISB_MASK ((uint)0x01800000) +#define BCSR0_DBGC_MASK ((uint)0x00600000) +#define BCSR0_DBPC_MASK ((uint)0x00180000) +#define BCSR0_EBDF_MASK ((uint)0x00060000) + +#define BCSR1_FLASH_EN ((uint)0x80000000) +#define BCSR1_DRAM_EN ((uint)0x40000000) +#define BCSR1_ETHEN ((uint)0x20000000) +#define BCSR1_IRDEN ((uint)0x10000000) +#define BCSR1_FLASH_CFG_EN ((uint)0x08000000) +#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000) +#define BCSR1_BCSR_EN ((uint)0x02000000) +#define BCSR1_RS232EN_1 ((uint)0x01000000) +#define BCSR1_PCCEN ((uint)0x00800000) +#define BCSR1_PCCVCC0 ((uint)0x00400000) +#define BCSR1_PCCVPP_MASK ((uint)0x00300000) +#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000) +#define BCSR1_RS232EN_2 ((uint)0x00040000) +#define BCSR1_SDRAM_EN ((uint)0x00020000) +#define BCSR1_PCCVCC1 ((uint)0x00010000) + +#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000) +#define BCSR2_DRAM_PD_MASK ((uint)0x07800000) +#define BCSR2_DRAM_PD_SHIFT (23) +#define BCSR2_EXTTOLI_MASK ((uint)0x00780000) +#define BCSR2_DBREVNR_MASK ((uint)0x00030000) + +#define BCSR3_DBID_MASK ((ushort)0x3800) +#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400) +#define BCSR3_BREVNR0 ((ushort)0x0080) +#define BCSR3_FLASH_PD_MASK ((ushort)0x0070) +#define BCSR3_BREVN1 ((ushort)0x0008) +#define BCSR3_BREVN2_MASK ((ushort)0x0003) + +#define BCSR4_ETHLOOP ((uint)0x80000000) +#define BCSR4_TFPLDL ((uint)0x40000000) +#define BCSR4_TPSQEL ((uint)0x20000000) +#define BCSR4_SIGNAL_LAMP ((uint)0x10000000) +#ifdef CONFIG_MPC823 +#define BCSR4_USB_EN ((uint)0x08000000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860SAR +#define BCSR4_UTOPIA_EN ((uint)0x08000000) +#endif /* CONFIG_MPC860SAR */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETH_EN ((uint)0x08000000) +#endif /* CONFIG_MPC860T */ +#ifdef CONFIG_MPC823 +#define BCSR4_USB_SPEED ((uint)0x04000000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETHCFG0 ((uint)0x04000000) +#endif /* CONFIG_MPC860T */ +#ifdef CONFIG_MPC823 +#define BCSR4_VCCO ((uint)0x02000000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETHFDE ((uint)0x02000000) +#endif /* CONFIG_MPC860T */ +#ifdef CONFIG_MPC823 +#define BCSR4_VIDEO_ON ((uint)0x00800000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC823 +#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETHCFG1 ((uint)0x00400000) +#endif /* CONFIG_MPC860T */ +#ifdef CONFIG_MPC823 +#define BCSR4_VIDEO_RST ((uint)0x00200000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETHRST ((uint)0x00200000) +#endif /* CONFIG_MPC860T */ +#define BCSR4_MODEM_EN ((uint)0x00100000) +#define BCSR4_DATA_VOICE ((uint)0x00080000) + +#define CONFIG_DRAM_50MHZ 1 +#define CONFIG_SDRAM_50MHZ + +#ifdef CONFIG_MPC860T + +/* Interrupt level assignments. +*/ +#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ + +#endif /* CONFIG_MPC860T */ + +/* We don't use the 8259. +*/ +#define NR_8259_INTS 0 + +/* Machine type +*/ +#define _MACH_8xx (_MACH_fads) + +#define CONFIG_DISK_SPINUP_TIME 1000000 + + +/* PCMCIA configuration */ + +#define PCMCIA_MAX_SLOTS 2 + +#ifdef CONFIG_MPC860 +#define PCMCIA_SLOT_A 1 +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/FLAGADM.h b/include/configs/FLAGADM.h new file mode 100644 index 0000000000..8babee140f --- /dev/null +++ b/include/configs/FLAGADM.h @@ -0,0 +1,302 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC823 1 /* This is a MPC823 CPU */ +#define CONFIG_FLAGADM 1 /* ...on a FLAGA DM */ +#define CONFIG_8xx_GCLK_FREQ 48000000 /*48MHz*/ + +#undef CONFIG_8xx_CONS_SMC1 /* Console is on SMC1 */ +#define CONFIG_8xx_CONS_SMC2 1 +#undef CONFIG_8xx_CONS_NONE + +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ +#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ + +#undef CONFIG_CLOCKS_IN_MHZ + +#if 0 +#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=bootp" +#define CONFIG_BOOTCOMMAND \ + "setenv bootargs root=/dev/ram ip=off panic=1;" \ + "bootm 40040000 400e0000" +#else +#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=bootp panic=1" +#define CONFIG_BOOTCOMMAND "bootp 0x400000; bootm 0x400000" +#endif /* 0|1*/ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +/*#define CONFIG_WATCHDOG*/ /* watchdog enabled */ +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_COMMANDS (CFG_CMD_BDI | CFG_CMD_IMI | CFG_CMD_CACHE | \ + CFG_CMD_MEMORY | CFG_CMD_FLASH | CFG_CMD_LOADB | CFG_CMD_LOADS | \ + CFG_CMD_ENV | CFG_CMD_REGINFO | CFG_CMD_IMMAP | CFG_CMD_NET) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "EEG> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0f00000 /* 1 ... 15 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x40040000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFF000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +/* This is a litlebit wasteful, but one sector is 128kb and we have to + * assigne a whole sector for the environment, so that we can safely + * erase and write it without disturbing the boot sector + */ +#define CFG_ENV_OFFSET 0x20000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#ifdef CONFIG_WATCHDOG +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_SWF | SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_PRE_SIUMCR (SIUMCR_DBGC11 | SIUMCR_MPRE | \ + SIUMCR_MLRC01 | SIUMCR_GB5E) +#define CFG_SIUMCR (CFG_PRE_SIUMCR | SIUMCR_DLK) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit miltiplier of 0x00b i.e. operation clock is + * 4MHz * (0x00b+1) = 4MHz * 12 = 48MHz + */ +#define CFG_PLPRCR (0x00b00000 | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR ( SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + +#define CFG_DER 0 + +/* + * In the Flaga DM we have: + * Flash on BR0/OR0/CS0a at 0x40000000 + * Display on BR1/OR1/CS1 at 0x20000000 + * SDRAM on BR2/OR2/CS2 at 0x00000000 + * Free BR3/OR3/CS3 + * DSP1 on BR4/OR4/CS4 at 0x80000000 + * DSP2 on BR5/OR5/CS5 at 0xa0000000 + * + * For now we just configure the Flash and the SDRAM and leave the others + * untouched. +*/ + +#define CFG_FLASH_PROTECTION 0 + +#define FLASH_BASE0 0x40000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_OR_AM 0xff000000 /* OR addr mask */ +#define CFG_OR_ATM 0x00006000 + +/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | \ + OR_SCY_3_CLK | OR_TRLX | OR_EHTR ) + +#define CFG_OR0_PRELIM (CFG_OR_AM | CFG_OR_ATM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE0 & BR_BA_MSK) | BR_PS_16 | BR_V ) + +/* + * BR2 and OR2 (SDRAM) + * + */ +#define SDRAM_BASE2 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM ( 0x00000800 ) + +#define CFG_OR2_PRELIM (CFG_OR_AM | CFG_OR_TIMING_SDRAM) +#define CFG_BR2_PRELIM ((SDRAM_BASE2 & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +#define CFG_BR2 CFG_BR2_PRELIM +#define CFG_OR2 CFG_OR2_PRELIM + +/* + * MAMR settings for SDRAM + */ +#define CFG_MAMR_48_SDR (CFG_MAMR_PTA | MAMR_WLFA_1X | MAMR_RLFA_1X \ + | MAMR_G0CLA_A11) + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 0x0F000000 + +/* + * BR4 and OR4 (DSP1) + * + * We do not wan't preliminary setup of the DSP, anyway we need the + * UPMB setup correctly before we can access the DSP. + * +*/ +#define DSP_BASE 0x80000000 + +#define CFG_OR4 ( OR_AM_MSK | OR_CSNT_SAM | OR_BI | OR_G5LS) +#define CFG_BR4 ( (DSP_BASE & BR_BA_MSK) | BR_PS_16 | BR_MS_UPMB | BR_V ) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/GTH.h b/include/configs/GTH.h new file mode 100644 index 0000000000..03b9659497 --- /dev/null +++ b/include/configs/GTH.h @@ -0,0 +1,374 @@ +/* + * Parameters for GTH board + * Based on FADS860T + * by thomas.lange@corelatus.com + + * A collection of structures, addresses, and values associated with + * the Motorola 860T FADS board. Copied from the MBX stuff. + * Magnus Damm added defines for 8xxrom and extended bd_info. + * Helmut Buchsbaum added bitvalues for BCSRx + * + * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) + */ + +/* + * ff000000 -> ff00ffff : IMAP internal in the cpu + * e0000000 -> ennnnnnn : pcmcia + * 98000000 -> 983nnnnn : FPGA 4MB + * 90000000 -> 903nnnnn : FPGA 4MB + * 80000000 -> 80nnnnnn : flash connected to CS0, final ( real ) location + * 00000000 -> nnnnnnnn : sdram + */ + +/* ------------------------------------------------------------------------- */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#include + +#define CONFIG_MPC860 1 +#define CONFIG_MPC860T 1 +#define CONFIG_GTH 1 + +#define CONFIG_MISC_INIT_R 1 + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 9600 +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ + +#define MPC8XX_FACT 3 /* Multiply by 3 */ +#define MPC8XX_XIN 16384000 /* 16.384 MHz */ +#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) + +#define CONFIG_BOOTDELAY 1 /* autoboot after 0 seconds */ + +#define CONFIG_ENV_OVERWRITE 1 /* Allow change of ethernet address */ + +#define CONFIG_BOOT_RETRY_TIME 5 /* Retry boot in 5 secs */ + +#define CONFIG_RESET_TO_RETRY 1 /* If timeout waiting for command, perform a reset */ + +/* Only interrupt boot if space is pressed */ +/* If a long serial cable is connected but */ +/* other end is dead, garbage will be read */ +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT "Press space to abort autoboot in %d second\n" +#define CONFIG_AUTOBOOT_DELAY_STR "d" +#define CONFIG_AUTOBOOT_STOP_STR " " + +#if 0 +/* Net boot */ +/* Loads a tftp image and starts it */ +#define CONFIG_BOOTCOMMAND "bootp;bootm 100000" /* autoboot command */ +#define CONFIG_BOOTARGS "panic=1" +#else +/* Compact flash boot */ +#define CONFIG_BOOTARGS "panic=1 root=/dev/hda7" +#define CONFIG_BOOTCOMMAND "disk 100000 0:5;bootm 100000" +#endif + +/* Enable watchdog */ +#define CONFIG_WATCHDOG 1 + +/* choose SCC1 ethernet (10BASET on motherboard) + * or FEC ethernet (10/100 on daughterboard) + */ +#if 1 +#define CONFIG_SCC1_ENET 1 /* use SCC1 ethernet */ +#undef CONFIG_FEC_ENET /* disable FEC ethernet */ +#define CFG_DISCOVER_PHY +#else +#undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */ +#define CONFIG_FEC_ENET 1 /* use FEC ethernet */ +#define CFG_DISCOVER_PHY +#endif +#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET) +#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured +#endif + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_IDE) +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_PROMPT "=>" /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */ + +/* Default location to load data from net */ +#define CFG_LOAD_ADDR 0x100000 + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFF000000 +#define CFG_IMMR_SIZE ((uint)(64 * 1024)) + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 + +#define CFG_FLASH_BASE 0x80000000 + +#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ + +#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ + +#define CFG_MONITOR_BASE TEXT_BASE + +#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#undef CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_OFFSET 0x000E0000 +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +#define CFG_ENV_SECT_SIZE 0x50000 /* see README - env sector total size */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*---------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ + +/*FIXME dont use for now */ +/*#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */ +/*#define CFG_RTCSC (RTCSC_RTF) */ + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) +/* PITE */ +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * set the PLL, the low-power modes and the reset control (15-29) + */ +#define CFG_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ + +/* FIXME check values */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_TBS|SCCR_RTSEL|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00) + + /*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 + +/* Because of the way the 860 starts up and assigns CS0 the +* entire address space, we have to set the memory controller +* differently. Normally, you write the option register +* first, and then enable the chip select by writing the +* base register. For CS0, you must write the base register +* first, followed by the option register. +*/ + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ +/* the other CS:s are determined by looking at parameters in BCSRx */ + +#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ + +#define CFG_REMAP_OR_AM 0xFF800000 /* 4 MB OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ + +#define FPGA_2_BASE 0x90000000 +#define FPGA_3_BASE 0x98000000 + +/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) + + +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/ +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16 ) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CONFIG_ETHADDR DE:AD:BE:EF:00:01 /* Ethernet address */ + +#ifdef CONFIG_MPC860T + +/* Interrupt level assignments. +*/ +#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ + +#endif /* CONFIG_MPC860T */ + +/* We don't use the 8259. +*/ +#define NR_8259_INTS 0 + +/* Machine type +*/ +#define _MACH_8xx (_MACH_gth) + +#ifdef CONFIG_MPC860 +#define PCMCIA_SLOT_A 1 +#define CONFIG_PCMCIA_SLOT_A 1 +#endif + +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 +#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320) +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320) +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x0100 + +#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ /* Force it - dont measure it */ + +#define PA_FRONT_LED ((u16)0x4) /* PA 13 */ +#define PA_FL_CONFIG ((u16)0x20) /* PA 10 */ +#define PA_FL_CE ((u16)0x1000) /* PA 3 */ + +#define PB_ID_GND ((u32)1) /* PB 31 */ +#define PB_REV_1 ((u32)2) /* PB 30 */ +#define PB_REV_0 ((u32)4) /* PB 29 */ +#define PB_BLUE_LED ((u32)0x400) /* PB 21 */ +#define PB_EEPROM ((u32)0x800) /* PB 20 */ +#define PB_ID_3 ((u32)0x2000) /* PB 18 */ +#define PB_ID_2 ((u32)0x4000) /* PB 17 */ +#define PB_ID_1 ((u32)0x8000) /* PB 16 */ +#define PB_ID_0 ((u32)0x10000) /* PB 15 */ + +/* NOTE. This is reset for 100Mbit port only */ +#define PC_ENET100_RESET ((ushort)0x0080) /* PC 8 */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/IAD210.h b/include/configs/IAD210.h new file mode 100644 index 0000000000..7b762266a8 --- /dev/null +++ b/include/configs/IAD210.h @@ -0,0 +1,378 @@ +/* + * (C) Copyright 2001, 2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include + + +# ifdef DEBUG +# warning DEBUG Defined +# endif /* DEBUG */ + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MPC860 1 +#define CONFIG_IAD210 1 /* ...on a IAD210 module */ +#define CONFIG_MPC860T 1 +#define CONFIG_MPC862 1 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ + +#undef CONFIG_8xx_CONS_SMC1 +#undef CONFIG_8xx_CONS_SMC2 +#define CONFIG_8xx_CONS_SCC2 /* V24 on SCC2 */ +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 9600 + + +# define MPC8XX_FACT 16 +# define CONFIG_8xx_GCLK_FREQ (64000000L) /* define if can't use get_gclk_freq */ +# define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#if 0 +# define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +# define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +/* using this define saves us updating another source file */ +#define CONFIG_BOARD_PRE_INIT 1 + +#undef CONFIG_BOOTARGS +/* #define CONFIG_BOOTCOMMAND \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ + "bootm" +*/ + +#define CONFIG_BOOTCOMMAND \ + "setenv bootargs root=/dev/nfs" \ + "ip=192.168.28.129:139.10.137.138:192.168.28.1:255.255.255.0:iadlinux002::off; " \ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* #define CONFIG_STATUS_LED 1*/ /* Status LED enabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +# undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */ +# define CONFIG_FEC_ENET 1 /* use FEC ethernet */ +# define CFG_DISCOVER_PHY 1 +# define CONFIG_FEC_UTOPIA 1 +# define CONFIG_ETHADDR 08:00:06:26:A2:6D +# define CONFIG_IPADDR 192.168.28.128 +# define CONFIG_SERVERIP 139.10.137.138 +# define CFG_DISCOVER_PHY 1 + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +# define CFG_I2C_SPEED 50000 +# define CFG_I2C_SLAVE 0xDD +# define CFG_I2C_EEPROM_ADDR 0x50 +/* + * Software (bit-bang) I2C driver configuration + */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | \ + CFG_CMD_DATE ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00100000 + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 +#define CFG_IMMR_SIZE ((uint)(64 * 1024)) + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x08000000 +#define CFG_FLASH_SIZE ((uint)(4 * 1024 * 1024)) /* max 16Mbyte */ + +#define CFG_RESET_ADDRESS 0xFFF00100 + +#if defined(DEBUG) +# define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +# define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif + +# define CFG_MONITOR_BASE CFG_FLASH_BASE +# define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * set the PLL, the low-power modes and the reset control (15-29) + */ +#define CFG_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 + +#define CFG_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \ + SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \ + SCCR_DFLCD000 |SCCR_DFALCD00 ) + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration Register 19-4 + *----------------------------------------------------------------------- + */ +/* +0x09C4 => DRQP = 10 (IDMA requests have lowest priority) */ +#define CFG_RCCR 0x0020 + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + */ +#define PCMCIA_MEM_ADDR ((uint)0xff020000) +#define PCMCIA_MEM_SIZE ((uint)(64 * 1024)) + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 + +/* Because of the way the 860 starts up and assigns CS0 the +* entire address space, we have to set the memory controller +* differently. Normally, you write the option register +* first, and then enable the chip select by writing the +* base register. For CS0, you must write the base register +* first, followed by the option register. +*/ + +/* + * Init Memory Controller: + * + * BR0 and OR0 (FLASH) + */ + +#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0xF8000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xF8000000 /* OR addr mask */ + +/* FLASH timing: + TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | \ + OR_SCY_3_CLK | OR_EHTR) + +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) + +/* + * BR2/3 and OR2/3 (SDRAM) + * + */ +#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ + +#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | OR_CSNT_SAM | OR_BI | OR_ACS_DIV4) +#define CFG_BR2_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) +#define CFG_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V) + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 124 /* start with divider for 64 MHz */ + +/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ +#define CFG_MPTPR MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +#define CFG_MAMR ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLB_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_8X) + + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#ifdef CONFIG_MPC860T + +/* Interrupt level assignments. +*/ +#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ + +#endif /* CONFIG_MPC860T */ + + +#endif /* __CONFIG_H */ diff --git a/include/configs/IVML24.h b/include/configs/IVML24.h new file mode 100644 index 0000000000..85900b5e0f --- /dev/null +++ b/include/configs/IVML24.h @@ -0,0 +1,475 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC860 1 /* This is a MPC860 CPU */ +#define CONFIG_IVML24 1 /* ...on a IVML24 board */ + +#if defined (CONFIG_IVML24_16M) +# define CONFIG_IDENT_STRING " IVML24" +#elif defined (CONFIG_IVML24_32M) +# define CONFIG_IDENT_STRING " IVML24_128" +#elif defined (CONFIG_IVML24_64M) +# define CONFIG_IDENT_STRING " IVML24_256" +#endif + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ +#define CONFIG_8xx_GCLK_FREQ 50331648 + +#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif +#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ + +#define CONFIG_BOOTARGS "root=/dev/nfs rw " \ + "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \ + "nfsaddrs=10.0.0.99:10.0.0.2" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_IDE) +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_BOOTP_MASK \ + ((CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) & ~CONFIG_BOOTP_GATEWAY) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/*----------------------------------------------------------------------*/ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ + +#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ + +#define CFG_PB_12V_ENABLE 0x00002000 /* PB 18 */ +#define CFG_PB_ILOCK_SWITCH 0x00004000 /* PB 17 */ +#define CFG_PB_SDRAM_CLKE 0x00008000 /* PB 16 */ +#define CFG_PB_ETH_POWERDOWN 0x00010000 /* PB 15 */ +#define CFG_PB_IDE_MOTOR 0x00020000 /* PB 14 */ + +#define CFG_PC_ETH_RESET ((ushort)0x0010) /* PC 11 */ +#define CFG_PC_IDE_RESET ((ushort)0x0020) /* PC 10 */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 /* was: 0xFF000000 */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR + +#if defined (CONFIG_IVML24_16M) +# define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#elif defined (CONFIG_IVML24_32M) +# define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */ +#elif defined (CONFIG_IVML24_64M) +# define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */ +#endif + +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFF000000 +#ifdef DEBUG +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x7A000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) + +# if defined (CONFIG_IVML24_16M) +# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +# elif defined (CONFIG_IVML24_32M) +# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWP) +# elif defined (CONFIG_IVML24_64M) +# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWP) +# endif + +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +/* EARB, DBGC and DBPC are initialised by the HCW */ +/* => 0x000000C0 */ +#define CFG_SIUMCR (SIUMCR_BSC | SIUMCR_GB5E) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit, set PLL multiplication factor ! + */ +/* 0x00B0C0C0 */ +#define CFG_PLPRCR \ + ( (11 << PLPRCR_MF_SHIFT) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | /*PLPRCR_TMIST|*/ \ + /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ + PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \ + ) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +/* 0x01800014 */ +#define CFG_SCCR (SCCR_COM01 | /*SCCR_TBS|*/ \ + SCCR_RTDIV | SCCR_RTSEL | \ + /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ + SCCR_EBDF00 | SCCR_DFSYNC00 | \ + SCCR_DFBRG00 | SCCR_DFNL000 | \ + SCCR_DFNH000 | SCCR_DFLCD101 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +/* 0x00C3 */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration Register 19-4 + *----------------------------------------------------------------------- + */ +/* TIMEP=2 */ +#define CFG_RCCR 0x0200 + +/*----------------------------------------------------------------------- + * RMDS - RISC Microcode Development Support Control Register + *----------------------------------------------------------------------- + */ +#define CFG_RMDS 0 + +/*----------------------------------------------------------------------- + * + * Interrupt Levels + *----------------------------------------------------------------------- + */ +#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */ +#define CONFIG_IDE_RESET 1 /* reset for ide supported */ + +#define CFG_IDE_MAXBUS 1 /* The IVML24 has only 1 IDE bus*/ +#define CFG_IDE_MAXDEVICE 1 /* ... and only 1 IDE device */ + +#define CFG_ATA_BASE_ADDR 0xFE100000 +#define CFG_ATA_IDE0_OFFSET 0x0000 +#undef CFG_ATA_IDE1_OFFSET /* only one IDE bus available */ + +#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ +#define CFG_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */ +#define CFG_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */ + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0 and OR0 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0xFF000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +/* EPROMs are 512kb */ +#define CFG_REMAP_OR_AM 0xFFF80000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFFF80000 /* OR addr mask */ + +/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ +#define CFG_OR_TIMING_FLASH (OR_SCY_5_CLK | OR_EHTR) + +#define CFG_OR0_REMAP ( CFG_REMAP_OR_AM | OR_ACS_DIV4 | OR_BI | \ + CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | OR_ACS_DIV4 | OR_BI | \ + CFG_OR_TIMING_FLASH) +/* 16 bit, bank valid */ +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) + +/* + * BR1/OR1 - ELIC SACCO bank @ 0xFE000000 + * + * AM=0xFFFF8 ATM=0 CSNT/SAM=1 ACS/G5LA/G5LS=3 BIH=1 SCY=2 SETA=0 TRLX=1 EHTR=1 + */ +#define ELIC_SACCO_BASE 0xFE000000 +#define ELIC_SACCO_OR_AM 0xFFFF8000 +#define ELIC_SACCO_TIMING (OR_SCY_2_CLK | OR_TRLX | OR_EHTR) + +#define CFG_OR1 (ELIC_SACCO_OR_AM | OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ + ELIC_SACCO_TIMING) +#define CFG_BR1 ((ELIC_SACCO_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) + +/* + * BR2/OR2 - ELIC EPIC bank @ 0xFE008000 + * + * AM=0xFFFF8 ATM=0 CSNT/SAM=1 ACS/G5LA/G5LS=3 BIH=1 SCY=2 SETA=0 TRLX=1 EHTR=1 + */ +#define ELIC_EPIC_BASE 0xFE008000 +#define ELIC_EPIC_OR_AM 0xFFFF8000 +#define ELIC_EPIC_TIMING (OR_SCY_2_CLK | OR_TRLX | OR_EHTR) + +#define CFG_OR2 (ELIC_EPIC_OR_AM | OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ + ELIC_EPIC_TIMING) +#define CFG_BR2 ((ELIC_EPIC_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) + +/* + * BR3/OR3: SDRAM + * + * Multiplexed addresses, GPL5 output to GPL5_A (don't care) + */ +#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */ +#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ +#define SDRAM_TIMING OR_SCY_0_CLK /* SDRAM-Timing */ + +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ + +#define CFG_OR3_PRELIM (SDRAM_PRELIM_OR_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING ) +#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V ) + +/* + * BR4/OR4 - HDLC Address + * + * AM=0xFFFF8 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=0 BIH=1 SCY=1 SETA=0 TRLX=0 EHTR=0 + */ +#define HDLC_ADDR_BASE 0xFE108000 /* HDLC Address area */ +#define HDLC_ADDR_OR_AM 0xFFFF8000 +#define HDLC_ADDR_TIMING OR_SCY_1_CLK + +#define CFG_OR4 (HDLC_ADDR_OR_AM | OR_BI | HDLC_ADDR_TIMING) +#define CFG_BR4 ((HDLC_ADDR_BASE & BR_BA_MSK) | BR_PS_8 | BR_WP | BR_V ) + +/* + * BR5/OR5: SHARC ADSP-2165L + * + * AM=0xFFC00 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=3 BIH=1 SCY=0 SETA=0 TRLX=0 EHTR=0 + */ +#define SHARC_BASE 0xFE400000 +#define SHARC_OR_AM 0xFFC00000 +#define SHARC_TIMING OR_SCY_0_CLK + +#define CFG_OR5 (SHARC_OR_AM | OR_ACS_DIV2 | OR_BI | SHARC_TIMING ) +#define CFG_BR5 ((SHARC_BASE & BR_BA_MSK) | BR_PS_32 | BR_MS_UPMA | BR_V ) + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTB 204 + +/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ + +#if defined (CONFIG_IVML24_16M) +# define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ +#elif defined (CONFIG_IVML24_32M) +# define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ +#elif defined (CONFIG_IVML24_64M) +# define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV8 /* setting for 1 bank */ +#endif + + +/* + * MBMR settings for SDRAM + */ + +#if defined (CONFIG_IVML24_16M) + /* 8 column SDRAM */ +# define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \ + MAMR_AMB_TYPE_0 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A11 | \ + MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X) +#elif defined (CONFIG_IVML24_32M) +/* 128 MBit SDRAM */ +# define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \ + MAMR_AMB_TYPE_1 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A10 | \ + MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X) +#elif defined (CONFIG_IVML24_64M) +/* 128 MBit SDRAM */ +# define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \ + MAMR_AMB_TYPE_1 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A10 | \ + MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X) +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/IVMS8.h b/include/configs/IVMS8.h new file mode 100644 index 0000000000..2725e77c83 --- /dev/null +++ b/include/configs/IVMS8.h @@ -0,0 +1,459 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC860 1 /* This is a MPC860 CPU */ +#define CONFIG_IVMS8 1 /* ...on a IVMS8 board */ + +#if defined (CONFIG_IVMS8_16M) +# define CONFIG_IDENT_STRING " IVMS8" +#elif defined (CONFIG_IVMS8_32M) +# define CONFIG_IDENT_STRING " IVMS8_128" +#elif defined (CONFIG_IVMS8_64M) +# define CONFIG_IDENT_STRING " IVMS8_256" +#endif + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ +#define CONFIG_8xx_GCLK_FREQ 50331648 + +#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif +#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ + +#define CONFIG_BOOTARGS "root=/dev/nfs rw " \ + "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \ + "nfsaddrs=10.0.0.99:10.0.0.2" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_IDE) +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_BOOTP_MASK \ + ((CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) & ~CONFIG_BOOTP_GATEWAY) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/*----------------------------------------------------------------------*/ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ + +#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ + +#define CFG_PB_SDRAM_CLKE 0x00008000 /* PB 16 */ +#define CFG_PB_ETH_POWERDOWN 0x00010000 /* PB 15 */ +#define CFG_PB_IDE_MOTOR 0x00020000 /* PB 14 */ + +#define CFG_PC_ETH_RESET ((ushort)0x0010) /* PC 11 */ +#define CFG_PC_IDE_RESET ((ushort)0x0020) /* PC 10 */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 /* was: 0xFF000000 */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#if defined (CONFIG_IVMS8_16M) +# define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#elif defined (CONFIG_IVMS8_32M) +# define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */ +#elif defined (CONFIG_IVMS8_64M) +# define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */ +#endif + +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFF000000 +#ifdef DEBUG +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x7A000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +# if defined (CONFIG_IVMS8_16M) +# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +# elif defined (CONFIG_IVMS8_32M) +# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWP) +# elif defined (CONFIG_IVMS8_64M) +# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWP) +# endif +#else +# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +/* EARB, DBGC and DBPC are initialised by the HCW */ +/* => 0x000000C0 */ +#define CFG_SIUMCR (SIUMCR_BSC | SIUMCR_GB5E) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit, set PLL multiplication factor ! + */ +/* 0x00B0C0C0 */ +#define CFG_PLPRCR \ + ( (11 << PLPRCR_MF_SHIFT) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | /*PLPRCR_TMIST|*/ \ + /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ + PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \ + ) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +/* 0x01800014 */ +#define CFG_SCCR (SCCR_COM01 | /*SCCR_TBS|*/ \ + SCCR_RTDIV | SCCR_RTSEL | \ + /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ + SCCR_EBDF00 | SCCR_DFSYNC00 | \ + SCCR_DFBRG00 | SCCR_DFNL000 | \ + SCCR_DFNH000 | SCCR_DFLCD101 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +/* 0x00C3 */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration Register 19-4 + *----------------------------------------------------------------------- + */ +/* TIMEP=2 */ +#define CFG_RCCR 0x0200 + +/*----------------------------------------------------------------------- + * RMDS - RISC Microcode Development Support Control Register + *----------------------------------------------------------------------- + */ +#define CFG_RMDS 0 + +/*----------------------------------------------------------------------- + * + * Interrupt Levels + *----------------------------------------------------------------------- + */ +#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */ +#define CONFIG_IDE_RESET 1 /* reset for ide supported */ + +#define CFG_IDE_MAXBUS 1 /* The IVMS8 has only 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* ... and only 1 IDE device */ + +#define CFG_ATA_BASE_ADDR 0xFE100000 +#define CFG_ATA_IDE0_OFFSET 0x0000 +#undef CFG_ATA_IDE1_OFFSET /* only one IDE bus available */ + +#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ +#define CFG_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */ +#define CFG_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */ + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0 and OR0 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0xFF000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +/* EPROMs are 512kb */ +#define CFG_REMAP_OR_AM 0xFFF80000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFFF80000 /* OR addr mask */ + +/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ +#define CFG_OR_TIMING_FLASH (/* OR_CSNT_SAM | */ OR_ACS_DIV4 | OR_BI | \ + OR_SCY_5_CLK | OR_EHTR) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +/* 16 bit, bank valid */ +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) + +/* + * BR1/OR1 - ELIC SACCO bank @ 0xFE000000 + * + * AM=0xFFFF8 ATM=0 CSNT/SAM=1 ACS/G5LA/G5LS=3 BIH=1 SCY=2 SETA=0 TRLX=1 EHTR=1 + */ +#define ELIC_SACCO_BASE 0xFE000000 +#define ELIC_SACCO_OR_AM 0xFFFF8000 +#define ELIC_SACCO_TIMING 0x00000F26 + +#define CFG_OR1 (ELIC_SACCO_OR_AM | ELIC_SACCO_TIMING) +#define CFG_BR1 ((ELIC_SACCO_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) + +/* + * BR2/OR2 - ELIC EPIC bank @ 0xFE008000 + * + * AM=0xFFFF8 ATM=0 CSNT/SAM=1 ACS/G5LA/G5LS=3 BIH=1 SCY=2 SETA=0 TRLX=1 EHTR=1 + */ +#define ELIC_EPIC_BASE 0xFE008000 +#define ELIC_EPIC_OR_AM 0xFFFF8000 +#define ELIC_EPIC_TIMING 0x00000F26 + +#define CFG_OR2 (ELIC_EPIC_OR_AM | ELIC_EPIC_TIMING) +#define CFG_BR2 ((ELIC_EPIC_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) + +/* + * BR3/OR3: SDRAM + * + * Multiplexed addresses, GPL5 output to GPL5_A (don't care) + */ +#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */ +#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ +#define SDRAM_TIMING 0x00000A00 /* SDRAM-Timing */ + +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ + +#define CFG_OR3_PRELIM (SDRAM_PRELIM_OR_AM | SDRAM_TIMING ) +#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V ) + +/* + * BR4/OR4: not used + */ + +/* + * BR5/OR5: SHARC ADSP-2165L + * + * AM=0xFFC00 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=3 BIH=1 SCY=0 SETA=0 TRLX=0 EHTR=0 + */ +#define SHARC_BASE 0xFE400000 +#define SHARC_OR_AM 0xFFC00000 +#define SHARC_TIMING 0x00000700 + +#define CFG_OR5 (SHARC_OR_AM | SHARC_TIMING ) +#define CFG_BR5 ((SHARC_BASE & BR_BA_MSK) | BR_PS_32 | BR_MS_UPMA | BR_V ) + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTB 204 + +/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#if defined (CONFIG_IVMS8_16M) + #define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ +#elif defined (CONFIG_IVMS8_32M) +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ +#elif defined (CONFIG_IVMS8_64M) +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV8 /* setting for 1 bank */ +#endif + + +/* + * MBMR settings for SDRAM + */ + +#if defined (CONFIG_IVMS8_16M) + /* 8 column SDRAM */ +# define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \ + MAMR_AMB_TYPE_0 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A11 | \ + MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X) +#elif defined (CONFIG_IVMS8_32M) +/* 128 MBit SDRAM */ +#define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \ + MAMR_AMB_TYPE_1 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A10 | \ + MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X) +#elif defined (CONFIG_IVMS8_64M) +/* 128 MBit SDRAM */ +#define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \ + MAMR_AMB_TYPE_1 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A10 | \ + MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X) + +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/MBX860T.h b/include/configs/MBX860T.h new file mode 100644 index 0000000000..0ca0970075 --- /dev/null +++ b/include/configs/MBX860T.h @@ -0,0 +1,407 @@ + /* + * A collection of structures, addresses, and values associated with + * the Motorola 860T MBX board. + * Copied from the FADS stuff, which was originally copied from the MBX stuff! + * Magnus Damm added defines for 8xxrom and extended bd_info. + * Helmut Buchsbaum added bitvalues for BCSRx + * Rob Taylor coverted it back to MBX + * + * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) + */ + +/* ------------------------------------------------------------------------- */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#include + +#define CONFIG_MPC860 1 +#define CONFIG_MPC860T 1 +#define CONFIG_MBX 1 + +#define CONFIG_8xx_CPUCLOCK 40 +#define CONFIG_8xx_BUSCLOCK (CONFIG_8xx_CPUCLOCK) +#define TARGET_SYSTEM_FREQUENCY 40 + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#define CONFIG_BAUDRATE 9600 + +#define MPC8XX_FACT 10 /* Multiply by 10 */ +#define MPC8XX_XIN 40000000 /* 50 MHz in */ +#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#if 1 +#define CONFIG_8xx_BOOTDELAY -1 /* autoboot disabled */ +#define CONFIG_8xx_TFTP_MODE +#else +#define CONFIG_8xx_BOOTDELAY 5 /* autoboot after 5 seconds */ +#undef CONFIG_8xx_TFTP_MODE +#endif + +#define CONFIG_DRAM_SPEED (CONFIG_8xx_BUSCLOCK) /* MHz */ +#define CONFIG_BOOTCOMMAND "bootm FE020000" /* autoboot command */ +#define CONFIG_BOOTARGS " " +/* + * Miscellaneous configurable options + */ +#undef CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT ":>" /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0800000 /* 4 ... 8 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFA00000 +#define CFG_IMMR_SIZE ((uint)(64 * 1024)) +#define CFG_NVRAM_BASE 0xFA000000 /* NVRAM */ +#define CFG_NVRAM_OR 0xffe00000 /* w/o speed dependent flags!! */ +#define CFG_CSR_BASE 0xFA100000 /* Control/Status Registers */ +#define CFG_PCIMEM_BASE 0x80000000 /* PCI I/O and Memory Spaces */ +#define CFG_PCIMEM_OR 0xA0000108 +#define CFG_PCIBRIDGE_BASE 0xFA210000 /* PCI-Bus Bridge Registers */ +#define CFG_PCIBRIDGE_OR 0xFFFF0108 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2f00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_VPD_SIZE 256 /* size in bytes reserved for vpd buffer */ +#define CFG_INIT_VPD_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_VPD_SIZE) +#define CFG_INIT_SP_OFFSET (CFG_INIT_VPD_OFFSET-8) + +/*----------------------------------------------------------------------- + * Offset in DPMEM where we keep the VPD data + */ +#define CFG_DPRAMVPD (CFG_INIT_VPD_OFFSET - 0x2000) + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x00000000 +/*0xFE000000*/ +#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_HWINFO_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CFG_HWINFO_LEN) +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 4 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +/*----------------------------------------------------------------------- + * NVRAM Configuration + * + * Note: the MBX is special because there is already a firmware on this + * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we + * access the NVRAM at the offset 0x1000. + */ +#define CFG_ENV_IS_IN_NVRAM 1 /* turn on NVRAM env feature */ +#define CFG_ENV_ADDR (CFG_NVRAM_BASE + 0x1000) +#define CFG_ENV_SIZE 0x1000 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit - leave PLL multiplication factor unchanged ! + */ +#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK (SCCR_RTDIV | SCCR_RTSEL) +#define CFG_SCCR SCCR_TBS + + /*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 + +/* Because of the way the 860 starts up and assigns CS0 the +* entire address space, we have to set the memory controller +* differently. Normally, you write the option register +* first, and then enable the chip select by writing the +* base register. For CS0, you must write the base register +* first, followed by the option register. +*/ + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ +/* the other CS:s are determined by looking at parameters in BCSRx */ + + +#define BCSR_ADDR ((uint) 0xFF010000) +#define BCSR_SIZE ((uint)(64 * 1024)) + +#define FLASH_BASE0_PRELIM 0xFE000000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0xFF010000 /* FLASH bank #0 */ + +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFFF00000 /* OR addr mask */ + +/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (0xFF800000 | OR_CSNT_SAM | OR_BI | OR_SCY_3_CLK) /* 1 Mbyte until detected and only 1 Mbyte is needed*/ +#define CFG_BR0_PRELIM (0xFE000000 | BR_V ) + +/* BCSRx - Board Control and Status Registers */ +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM 0xFFC00000 | OR_ACS_DIV4 +#define CFG_BR1_PRELIM (0x00000000 | BR_MS_UPMA | BR_V ) + + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */ + +/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +#define CFG_MAMR 0x13821000 +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/* values according to the manual */ + + +#define PCMCIA_MEM_ADDR ((uint)0xff020000) +#define PCMCIA_MEM_SIZE ((uint)(64 * 1024)) + +#define BCSR0 ((uint) (BCSR_ADDR + 00)) +#define BCSR1 ((uint) (BCSR_ADDR + 0x04)) +#define BCSR2 ((uint) (BCSR_ADDR + 0x08)) +#define BCSR3 ((uint) (BCSR_ADDR + 0x0c)) +#define BCSR4 ((uint) (BCSR_ADDR + 0x10)) + +/* FADS bitvalues by Helmut Buchsbaum + * see MPC8xxADS User's Manual for a proper description + * of the following structures + */ + +#define BCSR0_ERB ((uint)0x80000000) +#define BCSR0_IP ((uint)0x40000000) +#define BCSR0_BDIS ((uint)0x10000000) +#define BCSR0_BPS_MASK ((uint)0x0C000000) +#define BCSR0_ISB_MASK ((uint)0x01800000) +#define BCSR0_DBGC_MASK ((uint)0x00600000) +#define BCSR0_DBPC_MASK ((uint)0x00180000) +#define BCSR0_EBDF_MASK ((uint)0x00060000) + +#define BCSR1_FLASH_EN ((uint)0x80000000) +#define BCSR1_DRAM_EN ((uint)0x40000000) +#define BCSR1_ETHEN ((uint)0x20000000) +#define BCSR1_IRDEN ((uint)0x10000000) +#define BCSR1_FLASH_CFG_EN ((uint)0x08000000) +#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000) +#define BCSR1_BCSR_EN ((uint)0x02000000) +#define BCSR1_RS232EN_1 ((uint)0x01000000) +#define BCSR1_PCCEN ((uint)0x00800000) +#define BCSR1_PCCVCC0 ((uint)0x00400000) +#define BCSR1_PCCVPP_MASK ((uint)0x00300000) +#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000) +#define BCSR1_RS232EN_2 ((uint)0x00040000) +#define BCSR1_SDRAM_EN ((uint)0x00020000) +#define BCSR1_PCCVCC1 ((uint)0x00010000) + +#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000) +#define BCSR2_DRAM_PD_MASK ((uint)0x07800000) +#define BCSR2_DRAM_PD_SHIFT (23) +#define BCSR2_EXTTOLI_MASK ((uint)0x00780000) +#define BCSR2_DBREVNR_MASK ((uint)0x00030000) + +#define BCSR3_DBID_MASK ((ushort)0x3800) +#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400) +#define BCSR3_BREVNR0 ((ushort)0x0080) +#define BCSR3_FLASH_PD_MASK ((ushort)0x0070) +#define BCSR3_BREVN1 ((ushort)0x0008) +#define BCSR3_BREVN2_MASK ((ushort)0x0003) + +#define BCSR4_ETHLOOP ((uint)0x80000000) +#define BCSR4_TFPLDL ((uint)0x40000000) +#define BCSR4_TPSQEL ((uint)0x20000000) +#define BCSR4_SIGNAL_LAMP ((uint)0x10000000) +#ifdef CONFIG_MPC823 +#define BCSR4_USB_EN ((uint)0x08000000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860SAR +#define BCSR4_UTOPIA_EN ((uint)0x08000000) +#endif /* CONFIG_MPC860SAR */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETH_EN ((uint)0x08000000) +#endif /* CONFIG_MPC860T */ +#define BCSR4_USB_SPEED ((uint)0x04000000) +#define BCSR4_VCCO ((uint)0x02000000) +#define BCSR4_VIDEO_ON ((uint)0x00800000) +#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000) +#define BCSR4_VIDEO_RST ((uint)0x00200000) +#define BCSR4_MODEM_EN ((uint)0x00100000) +#define BCSR4_DATA_VOICE ((uint)0x00080000) + +#define CONFIG_DRAM_40MHZ 1 + +#ifdef CONFIG_MPC860T + +/* Interrupt level assignments. +*/ +#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ + +#endif /* CONFIG_MPC860T */ + +/* We don't use the 8259. +*/ +#define NR_8259_INTS 0 + +/* Machine type +*/ +#define _MACH_8xx (_MACH_fads) + +/* + * MPC8xx CPM Options + */ +#define CONFIG_SCC_ENET 1 +#define CONFIG_SCC1_ENET 1 +#define CONFIG_FEC_ENET 1 +#undef CONFIG_CPM_IIC +#undef CONFIG_UCODE_PATCH + + +#define CONFIG_DISK_SPINUP_TIME 1000000 + + +/* PCMCIA configuration */ + +#define PCMCIA_MAX_SLOTS 2 + +#ifdef CONFIG_MPC860 +#define PCMCIA_SLOT_A 1 +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/PM826.h b/include/configs/PM826.h new file mode 100644 index 0000000000..dc06f958cb --- /dev/null +++ b/include/configs/PM826.h @@ -0,0 +1,525 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#undef CFG_RAMBOOT + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */ +#define CONFIG_PM826 1 /* ...on a PM8260 module */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +# define CFG_I2C_SPEED 50000 +# define CFG_I2C_SLAVE 0xFE +/* + * Software (bit-bang) I2C driver configuration + */ +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00010000) +#define I2C_TRISTATE (iop->pdir &= ~0x00010000) +#define I2C_READ ((iop->pdat & 0x00010000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + + +#define CONFIG_RTC_PCF8563 +#define CFG_I2C_RTC_ADDR 0x51 + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else*/ +#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */ + +#if (CONFIG_ETHER_INDEX == 1) +/* + * - Rx-CLK is CLK11 + * - Tx-CLK is CLK10 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + +#endif /* CONFIG_ETHER_INDEX */ + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#define CONFIG_8260_CLKIN 64000000 /* in Hz */ + +#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC) +#define CONFIG_BAUDRATE 230400 +#else +#define CONFIG_BAUDRATE 9600 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_BEDBUG | \ + CFG_CMD_DATE | \ + CFG_CMD_EEPROM | \ + CFG_CMD_DOC) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Disk-On-Chip configuration + */ + +#define CFG_DOC_SHORT_TIMEOUT +#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ + +#define CFG_DOC_SUPPORT_2000 +#define CFG_DOC_SUPPORT_MILLENNIUM + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * Flash and Boot ROM mapping + */ + +#define CFG_BOOTROM_BASE 0x60000000 +#define CFG_BOOTROM_SIZE 0x00080000 +#define CFG_FLASH0_BASE 0x40000000 +#define CFG_FLASH0_SIZE 0x02000000 +#define CFG_DOC_BASE 0x60000000 +#define CFG_DOC_SIZE 0x00100000 + + +/* Flash bank size (for preliminary settings) + */ +#define CFG_FLASH_SIZE CFG_FLASH0_SIZE + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ + +#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +#if 0 +/* Start port with environment in flash; switch to EEPROM later */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_FLASH_BASE+0x40000) +#define CFG_ENV_SIZE 0x40000 +#define CFG_ENV_SECT_SIZE 0x40000 +#else +/* Final version: environment in EEPROM */ +#define CFG_ENV_IS_IN_EEPROM 1 +#define CFG_I2C_EEPROM_ADDR 0x58 +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CFG_ENV_OFFSET 0 +#define CFG_ENV_SIZE 2048 +#endif + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CFG_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CFG_SIUMCR. + */ +#if defined(CONFIG_BOOT_ROM) +#define CFG_HRCW_MASTER (HRCW_BPS01 | HRCW_CIP | HRCW_ISB100 | HRCW_BMS) +#else +#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS) +#endif + +/* no slaves so just fill with zeros */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xF0000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + * + * 60x SDRAM is mapped at CFG_SDRAM_BASE, local SDRAM + * is mapped at SDRAM_BASE2_PRELIM. + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE CFG_FLASH0_BASE +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ + HID0_IFEM|HID0_ABE) +#define CFG_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CFG_RMR RMR_CSRE + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ + +#define BCR_APD01 0x10000000 +#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */ + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#if 0 +#define CFG_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_CS10PC01) +#else +#define CFG_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10) +#endif + + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + */ +#define CFG_SCCR (SCCR_DFBRG01) + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 64 bit FLASH + * 1 60x SDRAM 64 bit SDRAM + * 2 Local SDRAM 32 bit SDRAM + * + */ + + /* Initialize SDRAM on local bus + */ +#define CFG_INIT_LOCAL_SDRAM + + +/* Minimum mask to separate preliminary + * address ranges for CS[0:2] + */ +#define CFG_MIN_AM_MASK 0xC0000000 + +#define CFG_MPTPR 0x1F00 + +#define CFG_MRS_OFFS 0x00000000 + + +#if defined(CONFIG_BOOT_ROM) +/* + * Bank 0 - Boot ROM (8 bit wide) + */ +#define CFG_BR0_PRELIM ((CFG_BOOTROM_BASE & BRx_BA_MSK)|\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_BOOTROM_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxG_EHTR |\ + ORxG_TRLX) + +/* + * Bank 1 - Flash (64 bit wide) + */ +#define CFG_BR1_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxG_EHTR |\ + ORxG_TRLX) + +#else /* ! CONFIG_BOOT_ROM */ + +/* + * Bank 0 - Flash (64 bit wide) + */ +#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxG_EHTR |\ + ORxG_TRLX) + +/* + * Bank 1 - Disk-On-Chip + */ +#define CFG_BR1_PRELIM ((CFG_DOC_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_DOC_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxG_EHTR |\ + ORxG_TRLX) + +#endif /* CONFIG_BOOT_ROM */ + +/* Bank 2 - SDRAM + */ +#define CFG_PSRT 0x0F +#ifndef CFG_RAMBOOT +#define CFG_BR2_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + + /* SDRAM initialization values for 8-column chips + */ +#define CFG_OR2_8COL (CFG_MIN_AM_MASK |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A9 |\ + ORxS_NUMR_12) + +#define CFG_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\ + PSDMR_BSMA_A14_A16 |\ + PSDMR_SDA10_PBI0_A10 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_1W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) + + /* SDRAM initialization values for 9-column chips + */ +#define CFG_OR2_9COL (CFG_MIN_AM_MASK |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A7 |\ + ORxS_NUMR_13) + +#define CFG_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\ + PSDMR_BSMA_A13_A15 |\ + PSDMR_SDA10_PBI0_A9 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_1W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) + +#define CFG_OR2_PRELIM CFG_OR2_9COL +#define CFG_PSDMR CFG_PSDMR_9COL + +#endif /* CFG_RAMBOOT */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/SCM.h b/include/configs/SCM.h new file mode 100644 index 0000000000..0dd46a0f83 --- /dev/null +++ b/include/configs/SCM.h @@ -0,0 +1,711 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */ +#define CONFIG_TQM8260 200 /* ...on a TQM8260 module Rev.200 */ +#define CONFIG_SCM 1 /* ...on a System Controller Module */ + +#if (CONFIG_TQM8260 <= 100) +# error "TQM8260 module revison not supported" +#endif + +/* We use a TQM8260 module with a 300MHz CPU */ +#define CONFIG_300MHz + +/* Define 60x busmode only if your TQM8260 has L2 cache! */ +#ifdef CONFIG_L2_CACHE +# define CONFIG_BUSMODE_60x 1 /* bus mode: 60x */ +#else +# undef CONFIG_BUSMODE_60x /* bus mode: 8260 */ +#endif + +/* The board with 300MHz CPU doesn't have L2 cache, but works in 60x bus mode */ +#ifdef CONFIG_300MHz +# define CONFIG_BUSMODE_60x +#endif + +#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */ + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +/* + * Software (bit-bang) I2C driver configuration + */ + +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00010000) +#define I2C_TRISTATE (iop->pdir &= ~0x00010000) +#define I2C_READ ((iop->pdat & 0x00010000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CFG_I2C_EEPROM_ADDR 0x50 +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +#define CONFIG_I2C_X + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else*/ +#ifdef CONFIG_82xx_CONS_SMC1 +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ +#endif +#ifdef CONFIG_82xx_CONS_SMC2 +#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ +#endif + +#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */ +#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */ +#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9 */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + * + * (On TQM8260 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the + * X.29 connector, and FCC2 is hardwired to the X.1 connector) + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */ + +#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1) + +/* + * - Rx-CLK is CLK12 + * - Tx-CLK is CLK11 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK12|CMXFCR_TF1CS_CLK11) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + +#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3) + +/* + * - Rx-CLK is CLK15 + * - Tx-CLK is CLK16 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + +#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */ + + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#ifndef CONFIG_300MHz +#define CONFIG_8260_CLKIN 66666666 /* in Hz */ +#else +#define CONFIG_8260_CLKIN 83333000 /* in Hz */ +#endif + +#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC) +#define CONFIG_BAUDRATE 230400 +#else +#define CONFIG_BAUDRATE 115200 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_DHCP | \ + CFG_CMD_I2C | \ + CFG_CMD_EEPROM | \ + CFG_CMD_BSP) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */ + +#define CONFIG_MISC_INIT_R /* have misc_init_r() function */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + + +/* What should the base address of the main FLASH be and how big is + * it (in MBytes)? This must contain TEXT_BASE from board/tqm8260/config.mk + * The main FLASH is whichever is connected to *CS0. + */ +#define CFG_FLASH0_BASE 0x40000000 +#define CFG_FLASH1_BASE 0x60000000 +#define CFG_FLASH0_SIZE 32 +#define CFG_FLASH1_SIZE 32 + +/* Flash bank size (for preliminary settings) + */ +#define CFG_FLASH_SIZE CFG_FLASH0_SIZE + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ + +#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +#if 0 +/* Start port with environment in flash; switch to EEPROM later */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_FLASH_BASE+0x40000) +#define CFG_ENV_SIZE 0x40000 +#define CFG_ENV_SECT_SIZE 0x40000 +#else +/* Final version: environment in EEPROM */ +#define CFG_ENV_IS_IN_EEPROM 1 +#define CFG_ENV_OFFSET 0 +#define CFG_ENV_SIZE 2048 +#endif + +/*----------------------------------------------------------------------- + * Hardware Information Block + */ +#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ +#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */ +#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CFG_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CFG_SIUMCR. + */ +#if defined(CONFIG_266MHz) +#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \ + HRCW_MODCK_H0111) +#elif defined(CONFIG_300MHz) +#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \ + HRCW_MODCK_H0110) +#else +#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS) +#endif + +/* no slaves so just fill with zeros */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + * + * 60x SDRAM is mapped at CFG_SDRAM_BASE, local SDRAM + * is mapped at SDRAM_BASE2_PRELIM. + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE CFG_FLASH0_BASE +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/*----------------------------------------------------------------------- + * Hardware Information Block + */ +#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ +#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */ +#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ + HID0_IFEM|HID0_ABE) +#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CFG_RMR RMR_CSRE + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#ifdef CONFIG_BUSMODE_60x +#define CFG_BCR (BCR_EBM|BCR_L2C|BCR_LETM|\ + BCR_NPQM0|BCR_NPQM1|BCR_NPQM2) /* 60x mode */ +#else +#define BCR_APD01 0x10000000 +#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */ +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#if 0 +#define CFG_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10) +#else +#define CFG_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10) +#endif + + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + * Ensure DFBRG is Divide by 16 + */ +#define CFG_SCCR 0 + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 64 bit FLASH + * 1 60x SDRAM 64 bit SDRAM + * 2 Local SDRAM 32 bit SDRAM + * + */ + + /* Initialize SDRAM on local bus + */ +#define CFG_INIT_LOCAL_SDRAM + +#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ + +/* Minimum mask to separate preliminary + * address ranges for CS[0:2] + */ +#define CFG_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */ +#define CFG_LOCAL_SDRAM_LIMIT (128<<20) /* less than 128 MB */ + +#define CFG_MPTPR 0x4000 + +/*----------------------------------------------------------------------------- + * Address for Mode Register Set (MRS) command + *----------------------------------------------------------------------------- + * In fact, the address is rather configuration data presented to the SDRAM on + * its address lines. Because the address lines may be mux'ed externally either + * for 8 column or 9 column devices, some bits appear twice in the 8260's + * address: + * + * | (RFU) | (RFU) | WBL | TM | CL | BT | Burst Length | + * | BA1 BA0 | A12 : A10 | A9 | A8 A7 | A6 : A4 | A3 | A2 : A0 | + * 8 columns mux'ing: | A9 | A10 A21 | A22 : A24 | A25 | A26 : A28 | + * 9 columns mux'ing: | A8 | A20 A21 | A22 : A24 | A25 | A26 : A28 | + * Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 | + *----------------------------------------------------------------------------- + */ +#define CFG_MRS_OFFS 0x00000110 + + +/* Bank 0 - FLASH + */ +#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxG_EHTR |\ + ORxG_TRLX) + + /* SDRAM on TQM8260 can have either 8 or 9 columns. + * The number affects configuration values. + */ + +/* Bank 1 - 60x bus SDRAM + */ +#define CFG_PSRT 0x20 +#define CFG_LSRT 0x20 +#ifndef CFG_RAMBOOT +#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM CFG_OR1_8COL + + + /* SDRAM initialization values for 8-column chips + */ +#define CFG_OR1_8COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A7 |\ + ORxS_NUMR_12) + +#define CFG_PSDMR_8COL (PSDMR_PBI |\ + PSDMR_SDAM_A15_IS_A5 |\ + PSDMR_BSMA_A12_A14 |\ + PSDMR_SDA10_PBI1_A8 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_EAMUX |\ + PSDMR_CL_2) + + /* SDRAM initialization values for 9-column chips + */ +#define CFG_OR1_9COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A5 |\ + ORxS_NUMR_13) + +#define CFG_PSDMR_9COL (PSDMR_PBI |\ + PSDMR_SDAM_A16_IS_A5 |\ + PSDMR_BSMA_A12_A14 |\ + PSDMR_SDA10_PBI1_A7 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_EAMUX |\ + PSDMR_CL_2) + +/* Bank 2 - Local bus SDRAM + */ +#ifdef CFG_INIT_LOCAL_SDRAM +#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_SDRAM_L |\ + BRx_V) + +#define CFG_OR2_PRELIM CFG_OR2_8COL + +#define SDRAM_BASE2_PRELIM 0x80000000 + + /* SDRAM initialization values for 8-column chips + */ +#define CFG_OR2_8COL ((~(CFG_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A8 |\ + ORxS_NUMR_12) + +#define CFG_LSDMR_8COL (PSDMR_PBI |\ + PSDMR_SDAM_A15_IS_A5 |\ + PSDMR_BSMA_A13_A15 |\ + PSDMR_SDA10_PBI1_A9 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_BL |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_CL_2) + + /* SDRAM initialization values for 9-column chips + */ +#define CFG_OR2_9COL ((~(CFG_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A6 |\ + ORxS_NUMR_13) + +#define CFG_LSDMR_9COL (PSDMR_PBI |\ + PSDMR_SDAM_A16_IS_A5 |\ + PSDMR_BSMA_A13_A15 |\ + PSDMR_SDA10_PBI1_A8 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_BL |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_CL_2) + +#endif /* CFG_INIT_LOCAL_SDRAM */ + +#endif /* CFG_RAMBOOT */ + +#define CFG_CAN0_BASE 0xc0000000 +#define CFG_CAN1_BASE 0xc0008000 +#define CFG_FIOX_BASE 0xc0010000 +#define CFG_FDOHM_BASE 0xc0018000 +#define CFG_EXTPROM_BASE 0xc2000000 + +#define CFG_CAN_SIZE 0x00000100 +#define CFG_FIOX_SIZE 0x00000020 +#define CFG_FDOHM_SIZE 0x00002000 +#define CFG_EXTPROM_BANK_SIZE 0x01000000 + +#define EXT_EEPROM_MAX_FLASH_BANKS 0x02 + +/* CS3 - CAN 0 + */ +#define CFG_CAN0_BR3 ((CFG_CAN0_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_UPMA |\ + BRx_V) + +#define CFG_CAN0_OR3 (P2SZ_TO_AM(CFG_CAN_SIZE) |\ + ORxU_BI |\ + ORxU_EHTR_4IDLE) + +/* CS4 - CAN 1 + */ +#define CFG_CAN1_BR4 ((CFG_CAN1_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_UPMA |\ + BRx_V) + +#define CFG_CAN1_OR4 (P2SZ_TO_AM(CFG_CAN_SIZE) |\ + ORxU_BI |\ + ORxU_EHTR_4IDLE) + +/* CS5 - Extended PROM (16MB optional) + */ +#define CFG_EXTPROM_BR5 ((CFG_EXTPROM_BASE & BRx_BA_MSK)|\ + BRx_PS_32 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_EXTPROM_OR5 (P2SZ_TO_AM(CFG_EXTPROM_BANK_SIZE)|\ + ORxG_CSNT |\ + ORxG_ACS_DIV4 |\ + ORxG_SCY_5_CLK |\ + ORxG_TRLX) + +/* CS6 - Extended PROM (16MB optional) + */ +#define CFG_EXTPROM_BR6 (((CFG_EXTPROM_BASE + \ + CFG_EXTPROM_BANK_SIZE) & BRx_BA_MSK)|\ + BRx_PS_32 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_EXTPROM_OR6 (P2SZ_TO_AM(CFG_EXTPROM_BANK_SIZE)|\ + ORxG_CSNT |\ + ORxG_ACS_DIV4 |\ + ORxG_SCY_5_CLK |\ + ORxG_TRLX) + +/* CS7 - FPGA FIOX: Glue Logic + */ +#define CFG_FIOX_BR7 ((CFG_FIOX_BASE & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_FIOX_OR7 (P2SZ_TO_AM(CFG_FIOX_SIZE) |\ + ORxG_ACS_DIV4 |\ + ORxG_SCY_5_CLK |\ + ORxG_TRLX) + +/* CS8 - FPGA DOH Master + */ +#define CFG_FDOHM_BR8 ((CFG_FDOHM_BASE & BRx_BA_MSK) |\ + BRx_PS_16 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_FDOHM_OR8 (P2SZ_TO_AM(CFG_FDOHM_SIZE) |\ + ORxG_ACS_DIV4 |\ + ORxG_SCY_5_CLK |\ + ORxG_TRLX) + + +/* FPGA configuration */ +#define CFG_PD_FIOX_PROG (1 << (31- 5)) /* PD 5 */ +#define CFG_PD_FIOX_DONE (1 << (31-28)) /* PD 28 */ +#define CFG_PD_FIOX_INIT (1 << (31-29)) /* PD 29 */ + +#define CFG_PD_FDOHM_PROG (1 << (31- 4)) /* PD 4 */ +#define CFG_PD_FDOHM_DONE (1 << (31-26)) /* PD 26 */ +#define CFG_PD_FDOHM_INIT (1 << (31-27)) /* PD 27 */ + + +#endif /* __CONFIG_H */ + diff --git a/include/configs/SPD823TS.h b/include/configs/SPD823TS.h new file mode 100644 index 0000000000..bbd5939f2f --- /dev/null +++ b/include/configs/SPD823TS.h @@ -0,0 +1,412 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC823 1 /* This is a MPC823 CPU */ +#define CONFIG_SPD823TS 1 /* ...on a SPD823TS board */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 115200 +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ + +#define CONFIG_BOOTARGS "root=/dev/nfs rw " \ + "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \ + "nfsaddrs=10.0.0.99:10.0.0.2" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_COMMANDS \ +((CONFIG_CMD_DFL & ~(CFG_CMD_FLASH)) | CFG_CMD_IDE) /* no Flash, but IDE */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/*----------------------------------------------------------------------*/ +#define CONFIG_ETHADDR 00:D0:93:00:01:CB +#define CONFIG_IPADDR 10.0.0.98 +#define CONFIG_SERVERIP 10.0.0.1 +#undef CONFIG_BOOTCOMMAND +#define CONFIG_BOOTCOMMAND "tftp 200000 pImage;bootm 200000" +/*----------------------------------------------------------------------*/ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ + +#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ + +#define CFG_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 /* was: 0xFF000000 */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFF000000 +#ifdef DEBUG +#define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 0 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 0 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 0 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 0 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x0800 /* Total Size of Environment Sector */ +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +/* 0x00000040 */ +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC00 | SIUMCR_GB5E) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit, set PLL multiplication factor ! + */ +/* 0x00b0c0c0 */ +#define CFG_PLPRCR \ + ( (11 << PLPRCR_MF_SHIFT) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | /*PLPRCR_TMIST|*/ \ + /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ + PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \ + ) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +/* 0x01800014 */ +#define CFG_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \ + SCCR_RTDIV | SCCR_RTSEL | \ + /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ + SCCR_EBDF00 | SCCR_DFSYNC00 | \ + SCCR_DFBRG00 | SCCR_DFNL000 | \ + SCCR_DFNH000 | SCCR_DFLCD101 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register + *----------------------------------------------------------------------- + */ +/* 0x00C3 */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration Register + *----------------------------------------------------------------------- + */ +/* TIMEP=2 */ +#define CFG_RCCR 0x0200 + +/*----------------------------------------------------------------------- + * RMDS - RISC Microcode Development Support Control Register + *----------------------------------------------------------------------- + */ +#define CFG_RMDS 0 + +/*----------------------------------------------------------------------- + * SDSR - SDMA Status Register + *----------------------------------------------------------------------- + */ +#define CFG_SDSR ((u_char)0x83) + +/*----------------------------------------------------------------------- + * SDMR - SDMA Mask Register + *----------------------------------------------------------------------- + */ +#define CFG_SDMR ((u_char)0x00) + +/*----------------------------------------------------------------------- + * + * Interrupt Levels + *----------------------------------------------------------------------- + */ +#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */ +#define CONFIG_IDE_LED 1 /* LED for ide supported */ +#define CONFIG_IDE_RESET 1 /* reset for ide supported */ + +#define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */ +#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ + +#define CFG_ATA_BASE_ADDR 0xFE100000 +#define CFG_ATA_IDE0_OFFSET 0x0000 +#define CFG_ATA_IDE1_OFFSET 0x0C00 + +#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ +#define CFG_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */ +#define CFG_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */ + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0xFF000000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0xFF080000 /* FLASH bank #1 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +/* EPROMs are 512kb */ +#define CFG_REMAP_OR_AM 0xFFF80000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFFF80000 /* OR addr mask */ + +/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ +#define CFG_OR_TIMING_FLASH (/* OR_CSNT_SAM | */ OR_ACS_DIV4 | OR_BI | \ + OR_SCY_5_CLK | OR_EHTR) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +/* 16 bit, bank valid */ +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) + +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM CFG_OR0_PRELIM +/* 16 bit, bank valid */ +#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) + +/* + * BR2-5 and OR2-5 (SRAM/SDRAM/PER8/SHARC) + * + */ +#define SRAM_BASE 0xFE200000 /* SRAM bank */ +#define SRAM_OR_AM 0xFFE00000 /* SRAM is 2 MB */ + +#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */ +#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ + +#define PER8_BASE 0xFE000000 /* PER8 bank */ +#define PER8_OR_AM 0xFFF00000 /* PER8 is 1 MB */ + +#define SHARC_BASE 0xFE400000 /* SHARC bank */ +#define SHARC_OR_AM 0xFFC00000 /* SHARC is 4 MB */ + +/* SRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ + +#define CFG_OR_TIMING_SRAM 0x00000D42 /* SRAM-Timing */ +#define CFG_OR2 (SRAM_OR_AM | CFG_OR_TIMING_SRAM ) +#define CFG_BR2 ((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V ) + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ + +#define CFG_OR_TIMING_SDRAM 0x00000A00 /* SDRAM-Timing */ +#define CFG_OR3_PRELIM (SDRAM_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM ) +#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V ) + +#define CFG_OR_TIMING_PER8 0x00000F32 /* PER8-Timing */ +#define CFG_OR4 (PER8_OR_AM | CFG_OR_TIMING_PER8 ) +#define CFG_BR4 ((PER8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) + +#define CFG_OR_TIMING_SHARC 0x00000700 /* SHARC-Timing */ +#define CFG_OR5 (SHARC_OR_AM | CFG_OR_TIMING_SHARC ) +#define CFG_BR5 ((SHARC_BASE & BR_BA_MSK) | BR_PS_32 | BR_MS_UPMA | BR_V ) +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTB 204 + +/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MBMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \ + MAMR_AMB_TYPE_0 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A11 | \ + MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h new file mode 100644 index 0000000000..9972312023 --- /dev/null +++ b/include/configs/TQM8260.h @@ -0,0 +1,617 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Imported from global configuration: + * CONFIG_L2_CACHE + * CONFIG_266MHz + * CONFIG_300MHz + */ + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */ + +#if 0 +#define CONFIG_TQM8260 100 /* ...on a TQM8260 module Rev.100 */ +#else +#define CONFIG_TQM8260 200 /* ...on a TQM8260 module Rev.200 */ +#endif + +/* Define 60x busmode only if your TQM8260 has L2 cache! */ +#ifdef CONFIG_L2_CACHE +# define CONFIG_BUSMODE_60x 1 /* bus mode: 60x */ +#else +# undef CONFIG_BUSMODE_60x /* bus mode: 8260 */ +#endif + +/* The board with 300MHz CPU doesn't have L2 cache, but works in 60x bus mode */ +#ifdef CONFIG_300MHz +# define CONFIG_BUSMODE_60x +#endif + +#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */ + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +/* + * Software (bit-bang) I2C driver configuration + */ + +/* TQM8260 Rev.100 has the clock and data pins swapped (!!!) on EEPROM */ +#if (CONFIG_TQM8260 <= 100) + +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00020000) +#define I2C_TRISTATE (iop->pdir &= ~0x00020000) +#define I2C_READ ((iop->pdat & 0x00020000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#else + +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00010000) +#define I2C_TRISTATE (iop->pdir &= ~0x00010000) +#define I2C_READ ((iop->pdat & 0x00010000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ +#endif + +#define CFG_I2C_EEPROM_ADDR 0x50 +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +#define CONFIG_I2C_X + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else*/ +#ifdef CONFIG_82xx_CONS_SMC1 +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ +#endif +#ifdef CONFIG_82xx_CONS_SMC2 +#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ +#endif + +#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */ +#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */ +#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9 */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + * + * (On TQM8260 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the + * X.29 connector, and FCC2 is hardwired to the X.1 connector) + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ + +#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1) + +/* + * - RX clk is CLK11 + * - TX clk is CLK12 + */ +# define CFG_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12) + +#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) + +/* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + +#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */ + + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#ifndef CONFIG_300MHz +#define CONFIG_8260_CLKIN 66666666 /* in Hz */ +#else +#define CONFIG_8260_CLKIN 83333000 /* in Hz */ +#endif + +#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC) +#define CONFIG_BAUDRATE 230400 +#else +#define CONFIG_BAUDRATE 9600 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_I2C | \ + CFG_CMD_EEPROM) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + + +/* What should the base address of the main FLASH be and how big is + * it (in MBytes)? This must contain TEXT_BASE from board/tqm8260/config.mk + * The main FLASH is whichever is connected to *CS0. + */ +#define CFG_FLASH0_BASE 0x40000000 +#define CFG_FLASH1_BASE 0x60000000 +#define CFG_FLASH0_SIZE 32 +#define CFG_FLASH1_SIZE 32 + +/* Flash bank size (for preliminary settings) + */ +#define CFG_FLASH_SIZE CFG_FLASH0_SIZE + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ + +#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +#if 0 +/* Start port with environment in flash; switch to EEPROM later */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_FLASH_BASE+0x40000) +#define CFG_ENV_SIZE 0x40000 +#define CFG_ENV_SECT_SIZE 0x40000 +#else +/* Final version: environment in EEPROM */ +#define CFG_ENV_IS_IN_EEPROM 1 +#define CFG_ENV_OFFSET 0 +#define CFG_ENV_SIZE 2048 +#endif + +/*----------------------------------------------------------------------- + * Hardware Information Block + */ +#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ +#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */ +#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CFG_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CFG_SIUMCR. + */ +#if defined(CONFIG_266MHz) +#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \ + HRCW_MODCK_H0111) +#elif defined(CONFIG_300MHz) +#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \ + HRCW_MODCK_H0110) +#else +#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS) +#endif + +/* no slaves so just fill with zeros */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + * + * 60x SDRAM is mapped at CFG_SDRAM_BASE, local SDRAM + * is mapped at SDRAM_BASE2_PRELIM. + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE CFG_FLASH0_BASE +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ + HID0_IFEM|HID0_ABE) +#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CFG_RMR RMR_CSRE + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#ifdef CONFIG_BUSMODE_60x +#define CFG_BCR (BCR_EBM|BCR_L2C|BCR_LETM|\ + BCR_NPQM0|BCR_NPQM1|BCR_NPQM2) /* 60x mode */ +#else +#define BCR_APD01 0x10000000 +#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */ +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#if 0 +#define CFG_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10) +#else +#define CFG_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10) +#endif + + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + * Ensure DFBRG is Divide by 16 + */ +#define CFG_SCCR 0 + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 64 bit FLASH + * 1 60x SDRAM 64 bit SDRAM + * 2 Local SDRAM 32 bit SDRAM + * + */ + + /* Initialize SDRAM on local bus + */ +#define CFG_INIT_LOCAL_SDRAM + +#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ + +/* Minimum mask to separate preliminary + * address ranges for CS[0:2] + */ +#define CFG_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */ +#define CFG_LOCAL_SDRAM_LIMIT (128<<20) /* less than 128 MB */ + +#define CFG_MPTPR 0x4000 + +/*----------------------------------------------------------------------------- + * Address for Mode Register Set (MRS) command + *----------------------------------------------------------------------------- + * In fact, the address is rather configuration data presented to the SDRAM on + * its address lines. Because the address lines may be mux'ed externally either + * for 8 column or 9 column devices, some bits appear twice in the 8260's + * address: + * + * | (RFU) | (RFU) | WBL | TM | CL | BT | Burst Length | + * | BA1 BA0 | A12 : A10 | A9 | A8 A7 | A6 : A4 | A3 | A2 : A0 | + * 8 columns mux'ing: | A9 | A10 A21 | A22 : A24 | A25 | A26 : A28 | + * 9 columns mux'ing: | A8 | A20 A21 | A22 : A24 | A25 | A26 : A28 | + * Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 | + *----------------------------------------------------------------------------- + */ +#define CFG_MRS_OFFS 0x00000110 + + +/* Bank 0 - FLASH + */ +#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxG_EHTR |\ + ORxG_TRLX) + + /* SDRAM on TQM8260 can have either 8 or 9 columns. + * The number affects configuration values. + */ + +/* Bank 1 - 60x bus SDRAM + */ +#define CFG_PSRT 0x20 +#define CFG_LSRT 0x20 +#ifndef CFG_RAMBOOT +#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM CFG_OR1_8COL + + + /* SDRAM initialization values for 8-column chips + */ +#define CFG_OR1_8COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A7 |\ + ORxS_NUMR_12) + +#define CFG_PSDMR_8COL (PSDMR_PBI |\ + PSDMR_SDAM_A15_IS_A5 |\ + PSDMR_BSMA_A12_A14 |\ + PSDMR_SDA10_PBI1_A8 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_EAMUX |\ + PSDMR_CL_2) + + /* SDRAM initialization values for 9-column chips + */ +#define CFG_OR1_9COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A5 |\ + ORxS_NUMR_13) + +#define CFG_PSDMR_9COL (PSDMR_PBI |\ + PSDMR_SDAM_A16_IS_A5 |\ + PSDMR_BSMA_A12_A14 |\ + PSDMR_SDA10_PBI1_A7 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_EAMUX |\ + PSDMR_CL_2) + +/* Bank 2 - Local bus SDRAM + */ +#ifdef CFG_INIT_LOCAL_SDRAM +#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_SDRAM_L |\ + BRx_V) + +#define CFG_OR2_PRELIM CFG_OR2_8COL + +#define SDRAM_BASE2_PRELIM 0x80000000 + + /* SDRAM initialization values for 8-column chips + */ +#define CFG_OR2_8COL ((~(CFG_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A8 |\ + ORxS_NUMR_12) + +#define CFG_LSDMR_8COL (PSDMR_PBI |\ + PSDMR_SDAM_A15_IS_A5 |\ + PSDMR_BSMA_A13_A15 |\ + PSDMR_SDA10_PBI1_A9 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_BL |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_CL_2) + + /* SDRAM initialization values for 9-column chips + */ +#define CFG_OR2_9COL ((~(CFG_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A6 |\ + ORxS_NUMR_13) + +#define CFG_LSDMR_9COL (PSDMR_PBI |\ + PSDMR_SDAM_A16_IS_A5 |\ + PSDMR_BSMA_A13_A15 |\ + PSDMR_SDA10_PBI1_A8 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_BL |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_CL_2) + +#endif /* CFG_INIT_LOCAL_SDRAM */ + +#endif /* CFG_RAMBOOT */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/WALNUT405.h b/include/configs/WALNUT405.h new file mode 100644 index 0000000000..68d47bb6d7 --- /dev/null +++ b/include/configs/WALNUT405.h @@ -0,0 +1,281 @@ +/* + * (C) Copyright 2000, 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_405GP 1 /* This is a PPC405 CPU */ +#define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_WALNUT405 1 /* ...on a WALNUT405 board */ + +#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ + +/*#define CFG_ENV_IS_IN_FLASH 1*/ /* use FLASH for environment vars */ +#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ + +#ifdef CFG_ENV_IS_IN_NVRAM +#undef CFG_ENV_IS_IN_FLASH +#else +#ifdef CFG_ENV_IS_IN_FLASH +#undef CFG_ENV_IS_IN_NVRAM +#endif +#endif + +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#if 1 +#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */ +#else +#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ +#endif + +/* Size (bytes) of interrupt driven serial port buffer. + * Set to 0 to use polling instead of interrupts. + * Setting to 0 will also disable RTS/CTS handshaking. + */ +#if 0 +#define CONFIG_SERIAL_SOFTWARE_FIFO 4000 +#else +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#endif + +#if 0 +#define CONFIG_BOOTARGS "root=/dev/nfs " \ + "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \ + "nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4" +#else +#define CONFIG_BOOTARGS "root=/dev/hda1 " \ + "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0" + +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 1 /* PHY address */ + +#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_PCI | \ + CFG_CMD_IRQ | \ + CFG_CMD_KGDB | \ + CFG_CMD_DHCP | \ + CFG_CMD_DATE | \ + CFG_CMD_BEDBUG | \ + CFG_CMD_ELF ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +/* + * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. + * If CFG_405_UART_ERRATA_59, then UART divisor is 31. + * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. + * The Linux BASE_BAUD define should match this configuration. + * baseBaud = cpuClock/(uartDivisor*16) + * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock, + * set Linux BASE_BAUD to 403200. + */ +#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ +#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CFG_BASE_BAUD 691200 + +/* The following table includes the supported baudrates */ +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + /* resource configuration */ + +#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ +#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ +#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ +#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ +#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ + +/*----------------------------------------------------------------------- + * External peripheral base address + *----------------------------------------------------------------------- + */ +#undef CONFIG_IDE_LED /* no led for ide supported */ +#undef CONFIG_IDE_RESET /* no reset for ide supported */ + +#define CFG_KEY_REG_BASE_ADDR 0xF0100000 +#define CFG_IR_REG_BASE_ADDR 0xF0200000 +#define CFG_FPGA_REG_BASE_ADDR 0xF0300000 + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFFF80000 +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +/* BEG ENVIRONNEMENT FLASH */ +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_OFFSET 0x00050000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ +#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */ +#endif +/* END ENVIRONNEMENT FLASH */ +/*----------------------------------------------------------------------- + * NVRAM organization + */ +#define CFG_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */ +#define CFG_NVRAM_SIZE 0x1ff8 /* NVRAM size */ + +#ifdef CFG_ENV_IS_IN_NVRAM +#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */ +#define CFG_ENV_ADDR \ + (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ +#endif +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ + + +/* Configuration Port location */ +#define CONFIG_PORT_ADDR 0xF0000500 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_DCACHE_CS 4 /* use cs # 4 for data cache memory */ + +#define CFG_INIT_RAM_ADDR 0x40000000 /* inside of SDRAM */ +#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Definitions for Serial Presence Detect EEPROM address + * (to get SDRAM settings) + */ +#define SPD_EEPROM_ADDRESS 0x50 + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ diff --git a/include/configs/c2mon.h b/include/configs/c2mon.h new file mode 100644 index 0000000000..b38150f4bc --- /dev/null +++ b/include/configs/c2mon.h @@ -0,0 +1,417 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC855 1 /* This is a MPC855 CPU */ +#define CONFIG_C2MON 1 /* ...on a C2MON module */ + +#define CONFIG_80MHz 1 /* Running at 5 * 16 = 80 MHz */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#undef CONFIG_STATUS_LED /* Status LED disabled */ + +#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_FEC_ENET 1 /* Use Fast Ethernet Controller */ + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_DHCP | \ + CFG_CMD_IDE | \ + CFG_CMD_DATE ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#undef CFG_HUSH_PARSER /* use "hush" command parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#if defined(DEBUG) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#ifndef CONFIG_CAN_DRIVER +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#else /* we must activate GPL5 in the SIUMCR for CAN */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#endif /* CONFIG_CAN_DRIVER */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + * + * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! + */ +#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */ +#define CFG_PLPRCR \ + ( (5-1)< + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Config header file for Cogent platform using an MPC8xx CPU module + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ +#define CONFIG_COGENT 1 /* using Cogent Modular Architecture */ + +/* Cogent Modular Architecture options */ +#define CONFIG_CMA282 1 /* ...on a CMA282 CPU module */ +#define CONFIG_CMA111 1 /* ...on a CMA111 motherboard */ + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else*/ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ +#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */ +#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */ +#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9,1=CLK5/CLK15*/ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#undef CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#define CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 1 /* which channel for ether */ + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#define CONFIG_8260_CLKIN 66666666 /* in Hz */ + +#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC) +#define CONFIG_BAUDRATE 230400 +#else +#define CONFIG_BAUDRATE 9600 +#endif + +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL|CFG_CMD_KGDB)&~CFG_CMD_NET) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#ifdef DEBUG +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif +#define CONFIG_BOOTCOMMAND "bootm 04080000 04200000" /* autoboot command*/ + +#define CONFIG_BOOTARGS "root=/dev/ram rw" + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ +#undef CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ +#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ +#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */ +#define CONFIG_KGDB_USE_EXTC /* SMC/SCC use ext clock not brg_clk */ +#define CONFIG_KGDB_EXTC_RATE 3686400 /* serial ext clk rate in Hz */ +#define CONFIG_KGDB_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9,1=CLK5/CLK15*/ +# if defined(CONFIG_KGDB_NONE) || defined(CONFIG_KGDB_USE_EXTC) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port at */ +# else +#define CONFIG_KGDB_BAUDRATE 9600 /* speed to run kgdb serial port at */ +# endif +#endif + +#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x01c00000 /* 4 ... 28 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/*----------------------------------------------------------------------- + * Low Level Cogent settings + * if CFG_CMA_CONS_SERIAL is defined, make sure the 8260 CPM serial is not. + * also, make sure CONFIG_CONS_INDEX is still defined - the index will be + * 1 for serialA, 2 for serialB, 3 for ser2A, 4 for ser2B + * (second 2 for CMA120 only) + */ +#define CFG_CMA_MB_BASE 0x00000000 /* base of m/b address space */ + +#include + +#ifdef CONFIG_CONS_NONE +#define CFG_CMA_CONS_SERIAL /* use Cogent motherboard serial for console */ +#endif +#define CFG_CMA_LCD_HEARTBEAT /* define for sec rotator in lcd corner */ + +#if (CMA_MB_CAPS & CMA_MB_CAP_FLASH) +/* + * flash exists on the motherboard + * set these four according to TOP dipsw: + * TOP on => ..._FLLOW_... (boot EPROM space is high so FLASH is low ) + * TOP off => ..._FLHIGH_... (boot EPROM space is low so FLASH is high) + */ +#define CMA_MB_FLASH_EXEC_BASE CMA_MB_FLLOW_EXEC_BASE +#define CMA_MB_FLASH_EXEC_SIZE CMA_MB_FLLOW_EXEC_SIZE +#define CMA_MB_FLASH_RDWR_BASE CMA_MB_FLLOW_RDWR_BASE +#define CMA_MB_FLASH_RDWR_SIZE CMA_MB_FLLOW_RDWR_SIZE +#endif +#define CMA_MB_FLASH_BASE CMA_MB_FLASH_EXEC_BASE +#define CMA_MB_FLASH_SIZE CMA_MB_FLASH_EXEC_SIZE + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CFG_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CFG_SIUMCR. + */ +#define CFG_HRCW_MASTER (HRCW_EBM|HRCW_BPS10|HRCW_L2CPC10|HRCW_DPPC11|\ + HRCW_ISB100|HRCW_MMR11|HRCW_MODCK_H0101) +/* no slaves so just duplicate the master hrcw */ +#define CFG_HRCW_SLAVE1 CFG_HRCW_MASTER +#define CFG_HRCW_SLAVE2 CFG_HRCW_MASTER +#define CFG_HRCW_SLAVE3 CFG_HRCW_MASTER +#define CFG_HRCW_SLAVE4 CFG_HRCW_MASTER +#define CFG_HRCW_SLAVE5 CFG_HRCW_MASTER +#define CFG_HRCW_SLAVE6 CFG_HRCW_MASTER +#define CFG_HRCW_SLAVE7 CFG_HRCW_MASTER + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xF0000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE CMA_MB_RAM_BASE +#ifdef CONFIG_CMA302 +#define CFG_FLASH_BASE CMA_MB_SLOT2_BASE /* cma302 in slot 2 */ +#else +#define CFG_FLASH_BASE CMA_MB_FLASH_BASE /* flash on m/b */ +#endif +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max num of memory banks */ +#define CFG_MAX_FLASH_SECT 67 /* max num of sects on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR CFG_FLASH_BASE /* Addr of Environment Sector */ +#ifdef CONFIG_CMA302 +#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ +#define CFG_ENV_SECT_SIZE (512*1024) /* see README - env sect real size */ +#else +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value*/ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ + HID0_IFEM|HID0_ABE) +#define CFG_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CFG_RMR RMR_CSRE + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define CFG_BCR BCR_EBM + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#define CFG_SIUMCR (SIUMCR_DPPC11|SIUMCR_L2CPC10|SIUMCR_MMR11) + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + * Ensure DFBRG is Divide by 16 + */ +#define CFG_SCCR (SCCR_DFBRG01) + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +#if defined(CONFIG_CMA282) + +/* + * Init Memory Controller: + * + * According to the Cogent manual, only CS0 and CS2 are used - CS0 for EPROM + * and CS2 for (optional) local bus RAM on the CPU module. + * + * Note the motherboard address space (256 Mbyte in size) is connected + * to the 60x Bus and is located starting at address 0. The Hard Reset + * Configuration Word should put the 60x Bus into External Bus Mode, since + * we dont set up any memory controller maps for it (see BCR[EBM], 4-26). + * + * (the *_SIZE vars must be a power of 2) + */ + +#define CFG_CMA_CS0_BASE TEXT_BASE /* EPROM */ +#define CFG_CMA_CS0_SIZE (1 << 20) +#if 0 +#define CFG_CMA_CS2_BASE 0x10000000 /* Local Bus SDRAM */ +#define CFG_CMA_CS2_SIZE (16 << 20) +#endif + +/* + * CS0 maps the EPROM on the cpu module + * Set it for 10 wait states, address CFG_MONITOR_BASE and size 1M + * + * Note: We must have already transferred control to the final location + * of the EPROM before these are used, because when BR0/OR0 are set, the + * mirror of the eprom at any other addresses will disappear. + */ + +/* base address = CFG_CMA_CS0_BASE, 16-bit, no parity, r/o, gpcm (60x bus) */ +#define CFG_BR0_PRELIM ((CFG_CMA_CS0_BASE&BRx_BA_MSK)|BRx_PS_16|BRx_WP|BRx_V) +/* mask size CFG_CMA_CS0_SIZE, csneg 1/4 early, adr-to-cs 1/2, 10-wait states */ +#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_CMA_CS0_SIZE)|\ + ORxG_CSNT|ORxG_ACS_DIV2|ORxG_SCY_10_CLK) + +/* + * CS2 enables the Local Bus SDRAM on the CPU Module + * + * Will leave this unset for the moment, because a) my CPU module has no + * SDRAM installed (it is optional); and b) it will require programming + * one of the UPMs in SDRAM mode - not a trivial job, and hard to get right + * if you can't test it. + */ + +#if 0 +/* base address = CFG_CMA_CS2_BASE, 32-bit, no parity, ??? */ +#define CFG_BR0_PRELIM ((CFG_CMA_CS2_BASE&BRx_BA_MSK)|BRx_PS_32|/*???*/|BRx_V) +/* mask size CFG_CMA_CS2_SIZE, CS time normal, ??? */ +#define CFG_OR2_PRELIM ((~(CFG_CMA_CS2_SIZE-1)&ORx_AM_MSK)|/*???*/) +#endif + +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/cogent_mpc8xx.h b/include/configs/cogent_mpc8xx.h new file mode 100644 index 0000000000..2fd4037fde --- /dev/null +++ b/include/configs/cogent_mpc8xx.h @@ -0,0 +1,357 @@ +/* + * (C) Copyright 2000 + * Murray Jensen + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Config header file for Cogent platform using an MPC8xx CPU module + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC860 1 /* This is an MPC860 CPU */ +#define CONFIG_COGENT 1 /* using Cogent Modular Architecture */ + +/* Cogent Modular Architecture options */ +#define CONFIG_CMA286_60_OLD 1 /* ...on an old CMA286-60 CPU module */ +#define CONFIG_CMA102 1 /* ...on a CMA102 motherboard */ +#define CONFIG_CMA302 1 /* ...with a CMA302 flash I/O module */ + +/* serial console configuration */ +#undef CONFIG_8xx_CONS_SMC1 +#undef CONFIG_8xx_CONS_SMC2 +#define CONFIG_8xx_CONS_NONE /* not on 8xx serial ports (eg on cogent m/b) */ + +#if defined(CONFIG_CMA286_60_OLD) +#define CONFIG_8xx_GCLK_FREQ 33333000 /* define if cant use get_gclk_freq */ +#endif + +#define CONFIG_BAUDRATE 230400 + +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + + +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_KGDB | CFG_CMD_I2C) & ~CFG_CMD_NET) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif +#define CONFIG_BOOTCOMMAND "bootm 04080000 04200000" /* autoboot command*/ + +#define CONFIG_BOOTARGS "root=/dev/ram rw" + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ +#undef CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ +#define CONFIG_KGDB_NONE /* define if kgdb on something else */ +#define CONFIG_KGDB_INDEX 2 /* which SMC/SCC channel for kgdb */ +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#endif + +#define CONFIG_WATCHDOG /* turn on platform specific watchdog */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x01c00000 /* 4 ... 28 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +#define CFG_ALLOC_DPRAM + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/*----------------------------------------------------------------------- + * Low Level Cogent settings + * if CFG_CMA_CONS_SERIAL is defined, make sure the 8xx CPM serial is not. + * also, make sure CONFIG_CONS_INDEX is still defined - the index will be + * 1 for serialA, 2 for serialB, 3 for ser2A, 4 for ser2B + * (second 2 for CMA120 only) + */ +#define CFG_CMA_MB_BASE 0x00000000 /* base of m/b address space */ + +#include + +#define CFG_CMA_CONS_SERIAL /* use Cogent motherboard serial for console */ +#define CONFIG_CONS_INDEX 1 +#define CFG_CMA_LCD_HEARTBEAT /* define for sec rotator in lcd corner */ +#if (CMA_MB_CAPS & CMA_MB_CAP_FLASH) +/* + * flash exists on the motherboard + * set these four according to TOP dipsw: + * TOP on => ..._FLLOW_... (boot EPROM space is high so FLASH is low ) + * TOP off => ..._FLHIGH_... (boot EPROM space is low so FLASH is high) + */ +#define CMA_MB_FLASH_EXEC_BASE CMA_MB_FLLOW_EXEC_BASE +#define CMA_MB_FLASH_EXEC_SIZE CMA_MB_FLLOW_EXEC_SIZE +#define CMA_MB_FLASH_RDWR_BASE CMA_MB_FLLOW_RDWR_BASE +#define CMA_MB_FLASH_RDWR_SIZE CMA_MB_FLLOW_RDWR_SIZE +#endif +#define CMA_MB_FLASH_BASE CMA_MB_FLASH_EXEC_BASE +#define CMA_MB_FLASH_SIZE CMA_MB_FLASH_EXEC_SIZE + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFF000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE CMA_MB_RAM_BASE +#ifdef CONFIG_CMA302 +#define CFG_FLASH_BASE CMA_MB_SLOT2_BASE /* cma302 in slot 2 */ +#else +#define CFG_FLASH_BASE CMA_MB_FLASH_BASE /* flash on m/b */ +#endif +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR CFG_FLASH_BASE /* Addr of Environment Sector */ +#ifdef CONFIG_CMA302 +#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ +#define CFG_ENV_SECT_SIZE (512*1024) /* see README - env sect real size */ +#else +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#endif +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit - leave PLL multiplication factor unchanged ! + */ +#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +#if defined(CONFIG_CMA286_60_OLD) + +/* + * Init Memory Controller: + * + * NOTE: although the names (CFG_xRn_PRELIM) suggest preliminary settings, + * they are actually the final settings for this cpu/board, because the + * flash and RAM are on the motherboard, accessed via the CMAbus, and the + * mappings are pretty much fixed. + * + * (the *_SIZE vars must be a power of 2) + */ + +#define CFG_CMA_CS0_BASE TEXT_BASE /* EPROM */ +#define CFG_CMA_CS0_SIZE (1 << 20) +#define CFG_CMA_CS1_BASE CMA_MB_RAM_BASE /* RAM + I/O SLOT 1 */ +#define CFG_CMA_CS1_SIZE (64 << 20) +#define CFG_CMA_CS2_BASE CMA_MB_SLOT2_BASE /* I/O SLOTS 2 + 3 */ +#define CFG_CMA_CS2_SIZE (64 << 20) +#define CFG_CMA_CS3_BASE CMA_MB_ROMLOW_BASE /* M/B I/O */ +#define CFG_CMA_CS3_SIZE (32 << 20) + +/* + * CS0 maps the EPROM on the cpu module + * Set it for 4 wait states, address CFG_MONITOR_BASE and size 1M + * + * Note: We must have already transferred control to the final location + * of the EPROM before these are used, because when BR0/OR0 are set, the + * mirror of the eprom at any other addresses will disappear. + */ + +/* base address = CFG_CMA_CS0_BASE, 16-bit, no parity, r/o, gpcm */ +#define CFG_BR0_PRELIM ((CFG_CMA_CS0_BASE&BR_BA_MSK)|BR_PS_16|BR_WP|BR_V) +/* mask size CFG_CMA_CS0_SIZE, CS time normal, burst inhibit, 4-wait states */ +#define CFG_OR0_PRELIM ((~(CFG_CMA_CS0_SIZE-1)&OR_AM_MSK)|OR_BI|OR_SCY_4_CLK) + +/* + * CS1 maps motherboard DRAM and motherboard I/O slot 1 + * (each 32Mbyte in size) + */ + +/* base address = CFG_CMA_CS1_BASE, 32-bit, no parity, r/w, gpcm */ +#define CFG_BR1_PRELIM ((CFG_CMA_CS1_BASE&BR_BA_MSK)|BR_V) +/* mask size CFG_CMA_CS1_SIZE, CS time normal, burst ok, ext xfer ack */ +#define CFG_OR1_PRELIM ((~(CFG_CMA_CS1_SIZE-1)&OR_AM_MSK)|OR_SETA) + +/* + * CS2 maps motherboard I/O slots 2 and 3 + * (each 32Mbyte in size) + */ + +/* base address = CFG_CMA_CS2_BASE, 32-bit, no parity, r/w, gpcm */ +#define CFG_BR2_PRELIM ((CFG_CMA_CS2_BASE&BR_BA_MSK)|BR_V) +/* mask size CFG_CMA_CS2_SIZE, CS time normal, burst ok, ext xfer ack */ +#define CFG_OR2_PRELIM ((~(CFG_CMA_CS2_SIZE-1)&OR_AM_MSK)|OR_SETA) + +/* + * CS3 maps motherboard I/O + * (32Mbyte in size) + */ + +/* base address = CFG_CMA_CS3_BASE, 32-bit, no parity, r/w, gpcm */ +#define CFG_BR3_PRELIM ((CFG_CMA_CS3_BASE&BR_BA_MSK)|BR_V) +/* mask size CFG_CMA_CS3_SIZE, CS time normal, burst inhibit, ext xfer ack */ +#define CFG_OR3_PRELIM ((~(CFG_CMA_CS3_SIZE-1)&OR_AM_MSK)|OR_BI|OR_SETA) + +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/pcu_e.h b/include/configs/pcu_e.h new file mode 100644 index 0000000000..42877a70f8 --- /dev/null +++ b/include/configs/pcu_e.h @@ -0,0 +1,535 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Workaround for layout bug on prototype board + */ +#define PCU_E_WITH_SWAPPED_CS 1 + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC860 1 /* This is a MPC860T CPU */ +#define CONFIG_MPC860T 1 +#define CONFIG_PCU_E 1 /* ...on a PCU E board */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ + +#define CONFIG_BAUDRATE 9600 +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ + "bootm" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ + +#define CONFIG_PRAM 2048 /* reserve 2 MB "protected RAM" */ + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#define CONFIG_SPI /* enable SPI driver */ +#define CONFIG_SPI_X /* 16 bit EEPROM addressing */ + +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + + +/* ---------------------------------------------------------------- + * Offset to initial SPI buffers in DPRAM (used if the environment + * is in the SPI EEPROM): We need a 520 byte scratch DPRAM area to + * use at an early stage. It is used between the two initialization + * calls (spi_init_f() and spi_init_r()). The value 0xB00 makes it + * far enough from the start of the data area (as well as from the + * stack pointer). + * ---------------------------------------------------------------- */ +#define CFG_SPI_INIT_OFFSET 0xB00 + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_DATE | \ + CFG_CMD_EEPROM | \ + CFG_CMD_BSP ) + +#define CONFIG_BOOTP_MASK \ + ((CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) & ~CONFIG_BOOTP_GATEWAY) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/*----------------------------------------------------------------------*/ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ + +#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ + +/* Ethernet hardware configuration done using port pins */ +#define CFG_PB_ETH_RESET 0x00000020 /* PB 26 */ +#if PCU_E_WITH_SWAPPED_CS /* XXX */ +#define CFG_PA_ETH_MDDIS 0x4000 /* PA 1 */ +#define CFG_PB_ETH_POWERDOWN 0x00000800 /* PB 20 */ +#define CFG_PB_ETH_CFG1 0x00000400 /* PB 21 */ +#define CFG_PB_ETH_CFG2 0x00000200 /* PB 22 */ +#define CFG_PB_ETH_CFG3 0x00000100 /* PB 23 */ +#else /* XXX */ +#define CFG_PB_ETH_MDDIS 0x00000010 /* PB 27 */ +#define CFG_PB_ETH_POWERDOWN 0x00000100 /* PB 23 */ +#define CFG_PB_ETH_CFG1 0x00000200 /* PB 22 */ +#define CFG_PB_ETH_CFG2 0x00000400 /* PB 21 */ +#define CFG_PB_ETH_CFG3 0x00000800 /* PB 20 */ +#endif /* XXX */ + +/* Ethernet settings: + * MDIO enabled, autonegotiation, 10/100Mbps, half/full duplex + */ +#define CFG_ETH_MDDIS_VALUE 0 +#define CFG_ETH_CFG1_VALUE 1 +#define CFG_ETH_CFG2_VALUE 1 +#define CFG_ETH_CFG3_VALUE 1 + +/* PUMA configuration */ +#if PCU_E_WITH_SWAPPED_CS /* XXX */ +#define CFG_PB_PUMA_PROG 0x00000010 /* PB 27 */ +#else /* XXX */ +#define CFG_PA_PUMA_PROG 0x4000 /* PA 1 */ +#endif /* XXX */ +#define CFG_PC_PUMA_DONE 0x0008 /* PC 12 */ +#define CFG_PC_PUMA_INIT 0x0004 /* PC 13 */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFE000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Address accessed to reset the board - must not be mapped/assigned + */ +#define CFG_RESET_ADDRESS 0xFEFFFFFF + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +/* this is an ugly hack needed because of the silly non-constant address map */ +#define CFG_FLASH_BASE (0-flash_info[0].size-flash_info[1].size) + +#if defined(DEBUG) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 160 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ + +#if 0 +/* Start port with environment in flash; switch to SPI EEPROM later */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment */ +#define CFG_ENV_ADDR 0xFFFFE000 /* Address of Environment Sector */ +#define CFG_ENV_SECT_SIZE 0x2000 /* use the top-most 8k boot sector */ +#else +/* Final version: environment in EEPROM */ +#define CFG_ENV_IS_IN_EEPROM 1 +#define CFG_I2C_EEPROM_ADDR 0 +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_ENV_OFFSET 1024 +#define CFG_ENV_SIZE 1024 +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * External Arbitration max. priority (7), + * Debug pins configuration '11', + * Asynchronous external master enable. + */ +/* => 0x70600200 */ +#define CFG_SIUMCR (SIUMCR_EARP7 | SIUMCR_DBGC11 | SIUMCR_AEME) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit, set PLL multiplication factor ! + */ +/* 0x00004080 */ +#define CFG_PLPRCR_MF 0 /* (0+1) * 50 = 50 MHz Clock */ +#define CFG_PLPRCR \ + ( (CFG_PLPRCR_MF << PLPRCR_MF_SHIFT) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \ + /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ + PLPRCR_CSR /*| PLPRCR_LOLRE|PLPRCR_FIOPD*/ \ + ) + +#define CONFIG_8xx_GCLK_FREQ ((CFG_PLPRCR_MF+1)*50000000) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + * + * Note: PITRTCLK is 50MHz / 512 = 97'656.25 Hz + */ +#define SCCR_MASK SCCR_EBDF11 +/* 0x01800000 */ +#define CFG_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \ + SCCR_RTDIV | SCCR_RTSEL | \ + /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ + SCCR_EBDF00 | SCCR_DFSYNC00 | \ + SCCR_DFBRG00 | SCCR_DFNL000 | \ + SCCR_DFNH000 | SCCR_DFLCD100 | \ + SCCR_DFALCD01) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + * + * Note: RTC counts at PITRTCLK / 8'192 = 11.920928 Hz !!! + * + * Don't expect the "date" command to work without a 32kHz clock input! + */ +/* 0x00C3 => 0x0003 */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration Register 19-4 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0x0000 + +/*----------------------------------------------------------------------- + * RMDS - RISC Microcode Development Support Control Register + *----------------------------------------------------------------------- + */ +#define CFG_RMDS 0 + +/*----------------------------------------------------------------------- + * + * Interrupt Levels + *----------------------------------------------------------------------- + */ +#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) - second Flash bank optional + */ + +#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */ +#if PCU_E_WITH_SWAPPED_CS /* XXX */ +#define FLASH_BASE6_PRELIM 0xFF000000 /* FLASH bank #1 */ +#else /* XXX */ +#define FLASH_BASE1_PRELIM 0xFF000000 /* FLASH bank #1 */ +#endif /* XXX */ + +/* + * used to re-map FLASH: restrict access enough but not too much to + * meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0xFF800000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ + +/* FLASH timing: CSNT = 0, ACS = 00, SCY = 8, EHTR = 1 */ +#define CFG_OR_TIMING_FLASH (OR_SCY_8_CLK | OR_EHTR) + +#define CFG_OR0_REMAP ( CFG_REMAP_OR_AM | OR_ACS_DIV1 | OR_BI | \ + CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | OR_ACS_DIV1 | OR_BI | \ + CFG_OR_TIMING_FLASH) +/* 16 bit, bank valid */ +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) + +#if PCU_E_WITH_SWAPPED_CS /* XXX */ +#define CFG_OR6_REMAP CFG_OR0_REMAP +#define CFG_OR6_PRELIM CFG_OR0_PRELIM +#define CFG_BR6_PRELIM ((FLASH_BASE6_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) +#else /* XXX */ +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM CFG_OR0_PRELIM +#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) +#endif /* XXX */ + +/* + * BR2/OR2: SDRAM + * + * Multiplexed addresses, GPL5 output to GPL5_A (don't care) + */ +#if PCU_E_WITH_SWAPPED_CS /* XXX */ +#define SDRAM_BASE5_PRELIM 0x00000000 /* SDRAM bank */ +#else /* XXX */ +#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank */ +#endif /* XXX */ +#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map 128 MB (>SDRAM_MAX_SIZE!) */ +#define SDRAM_TIMING OR_CSNT_SAM /* SDRAM-Timing */ + +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ + +#if PCU_E_WITH_SWAPPED_CS /* XXX */ +#define CFG_OR5_PRELIM (SDRAM_PRELIM_OR_AM | SDRAM_TIMING ) +#define CFG_BR5_PRELIM ((SDRAM_BASE5_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) +#else /* XXX */ +#define CFG_OR2_PRELIM (SDRAM_PRELIM_OR_AM | SDRAM_TIMING ) +#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) +#endif /* XXX */ + +/* + * BR3/OR3: CAN Controller + * BR3: 0x10000401 OR3: 0xffff818a + */ +#define CAN_CTRLR_BASE 0x10000000 /* CAN Controller */ +#define CAN_CTRLR_OR_AM 0xFFFF8000 /* 32 kB */ +#define CAN_CTRLR_TIMING (OR_BI | OR_SCY_8_CLK | OR_SETA | OR_EHTR) + +#if PCU_E_WITH_SWAPPED_CS /* XXX */ +#define CFG_BR4_PRELIM ((CAN_CTRLR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) +#define CFG_OR4_PRELIM (CAN_CTRLR_OR_AM | CAN_CTRLR_TIMING) +#else /* XXX */ +#define CFG_BR3_PRELIM ((CAN_CTRLR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) +#define CFG_OR3_PRELIM (CAN_CTRLR_OR_AM | CAN_CTRLR_TIMING) +#endif /* XXX */ + +/* + * BR4/OR4: PUMA Config + * + * Memory controller will be used in 2 modes: + * + * - "read" mode: + * BR4: 0x10100801 OR4: 0xffff8530 + * - "load" mode (chip select on UPM B): + * BR4: 0x101008c1 OR4: 0xffff8630 + * + * Default initialization is in "read" mode + */ +#define PUMA_CONF_BASE 0x10100000 /* PUMA Config */ +#define PUMA_CONF_OR_AM 0xFFFF8000 /* 32 kB */ +#define PUMA_CONF_LOAD_TIMING (OR_ACS_DIV2 | OR_SCY_3_CLK) +#define PUMA_CONF_READ_TIMING (OR_G5LA | OR_BI | OR_SCY_3_CLK) + +#define PUMA_CONF_BR_LOAD ((PUMA_CONF_BASE & BR_BA_MSK) | \ + BR_PS_16 | BR_MS_UPMB | BR_V) +#define PUMA_CONF_OR_LOAD (PUMA_CONF_OR_AM | PUMA_CONF_LOAD_TIMING) + +#define PUMA_CONF_BR_READ ((PUMA_CONF_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) +#define PUMA_CONF_OR_READ (PUMA_CONF_OR_AM | PUMA_CONF_READ_TIMING) + +#if PCU_E_WITH_SWAPPED_CS /* XXX */ +#define CFG_BR3_PRELIM PUMA_CONF_BR_READ +#define CFG_OR3_PRELIM PUMA_CONF_OR_READ +#else /* XXX */ +#define CFG_BR4_PRELIM PUMA_CONF_BR_READ +#define CFG_OR4_PRELIM PUMA_CONF_OR_READ +#endif /* XXX */ + +/* + * BR5/OR5: PUMA: SMA Bus 8 Bit + * BR5: 0x10200401 OR5: 0xffe0010a + */ +#define PUMA_SMA8_BASE 0x10200000 /* PUMA SMA Bus 8 Bit */ +#define PUMA_SMA8_OR_AM 0xFFE00000 /* 2 MB */ +#define PUMA_SMA8_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) + +#if PCU_E_WITH_SWAPPED_CS /* XXX */ +#define CFG_BR2_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) +#define CFG_OR2_PRELIM (PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA) +#else /* XXX */ +#define CFG_BR5_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) +#define CFG_OR5_PRELIM (PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA) +#endif /* XXX */ + +/* + * BR6/OR6: PUMA: SMA Bus 16 Bit + * BR6: 0x10600801 OR6: 0xffe0010a + */ +#define PUMA_SMA16_BASE 0x10600000 /* PUMA SMA Bus 16 Bit */ +#define PUMA_SMA16_OR_AM 0xFFE00000 /* 2 MB */ +#define PUMA_SMA16_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) + +#if PCU_E_WITH_SWAPPED_CS /* XXX */ +#define CFG_BR1_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) +#define CFG_OR1_PRELIM (PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA) +#else /* XXX */ +#define CFG_BR6_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) +#define CFG_OR6_PRELIM (PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA) +#endif /* XXX */ + +/* + * BR7/OR7: PUMA: external Flash + * BR7: 0x10a00801 OR7: 0xfe00010a + */ +#define PUMA_FLASH_BASE 0x10A00000 /* PUMA external Flash */ +#define PUMA_FLASH_OR_AM 0xFE000000 /* 32 MB */ +#define PUMA_FLASH_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR) + +#define CFG_BR7_PRELIM ((PUMA_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) +#define CFG_OR7_PRELIM (PUMA_FLASH_OR_AM | PUMA_FLASH_TIMING | OR_SETA) + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MPTPR 0x0200 + +/* + * MAMR settings for SDRAM + * 0x30104118 = Timer A period 0x30, MAMR_AMB_TYPE_1, MAMR_G0CLB_A10, + * MAMR_RLFB_1X, MAMR_WLFB_1X, MAMR_TLFB_8X + * 0x30904114 = - " - | Periodic Timer A Enable, MAMR_TLFB_4X + */ +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 0x30 /* = 48 */ + +#define CFG_MAMR ( (CFG_MAMR_PTA << MAMR_PTA_SHIFT) | \ + MAMR_AMB_TYPE_1 | \ + MAMR_G0CLB_A10 | \ + MAMR_RLFB_1X | \ + MAMR_WLFB_1X | \ + MAMR_TLFB_8X ) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */