From: Konstantin Porotchkin Date: Wed, 8 Feb 2017 15:34:13 +0000 (+0200) Subject: mvebu: pcie: Add support for GPIO reset for PCIe device X-Git-Tag: v2017.05-rc1~17^2~20 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=130b53ec79f3f1b1349d409f08f1f17e68a15f96;p=u-boot mvebu: pcie: Add support for GPIO reset for PCIe device Add support for "marvell,reset-gpio" property to mvebu DW PCIe driver. This option is valid when CONFIG_DM_GPIO=y Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986 Signed-off-by: Konstantin Porotchkin Signed-off-by: Rabeeh Khoury Cc: Stefan Roese Cc: Nadav Haklai Cc: Neta Zur Hershkovits Cc: Igal Liberman Cc: Haim Boot Signed-off-by: Stefan Roese --- diff --git a/doc/device-tree-bindings/pci/armada8k-pcie.txt b/doc/device-tree-bindings/pci/armada8k-pcie.txt new file mode 100644 index 0000000000..7230f10443 --- /dev/null +++ b/doc/device-tree-bindings/pci/armada8k-pcie.txt @@ -0,0 +1,49 @@ +Armada-8K PCIe DT details: +========================== + +Armada-8k uses synopsis designware PCIe controller. + +Required properties: +- compatible : should be "marvell,armada8k-pcie", "snps,dw-pcie". +- reg: base addresses and lengths of the pcie control and global control registers. + "ctrl" registers points to the global control registers, while the "config" space + points to the pcie configuration registers as mentioned in dw-pcie dt bindings in the link below. +- interrupt-map-mask and interrupt-map, standard PCI properties to + define the mapping of the PCIe interface to interrupt numbers. +- All other definitions as per generic PCI bindings +See Linux kernel documentation: +"Documentation/devicetree/bindings/pci/designware-pcie.txt" + +Optional properties: +PHY support is still not supported for armada-8k, once it will, the following parameters can be used: +- phys : phandle to phy node associated with pcie controller. +- phy-names : must be "pcie-phy" +- marvell,reset-gpio : specifies a gpio that needs to be activated for plug-in + card reset signal release. +Example: + +cpm_pcie0: pcie@f2600000 { + compatible = "marvell,armada8k-pcie", "snps,dw-pcie"; + reg = <0 0xf2600000 0 0x10000>, + <0 0xf6f00000 0 0x80000>; + reg-names = "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + dma-coherent; + + bus-range = <0 0xff>; + ranges = + /* downstream I/O */ + <0x81000000 0 0xf9000000 0 0xf9000000 0 0x10000 + /* non-prefetchable memory */ + 0x82000000 0 0xf6000000 0 0xf6000000 0 0xf00000>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + interrupts = ; + num-lanes = <1>; + clocks = <&cpm_syscon0 1 13>; + marvell,reset-gpio = <&cpm_gpio1 20 GPIO_ACTIVE_HIGH>; + status = "disabled"; +}; diff --git a/drivers/pci/pcie_dw_mvebu.c b/drivers/pci/pcie_dw_mvebu.c index 17fa0244d0..d4776a9c81 100644 --- a/drivers/pci/pcie_dw_mvebu.c +++ b/drivers/pci/pcie_dw_mvebu.c @@ -15,6 +15,7 @@ #include #include #include +#include DECLARE_GLOBAL_DATA_PTR; @@ -461,6 +462,25 @@ static int pcie_dw_mvebu_probe(struct udevice *dev) struct pcie_dw_mvebu *pcie = dev_get_priv(dev); struct udevice *ctlr = pci_get_controller(dev); struct pci_controller *hose = dev_get_uclass_priv(ctlr); +#ifdef CONFIG_DM_GPIO + struct gpio_desc reset_gpio; + + gpio_request_by_name(dev, "marvell,reset-gpio", 0, &reset_gpio, + GPIOD_IS_OUT); + /* + * Issue reset to add-in card trough the dedicated GPIO. + * Some boards are connecting the card reset pin to common system + * reset wire and others are using separate GPIO port. + * In the last case we have to release a reset of the addon card + * using this GPIO. + */ + if (dm_gpio_is_valid(&reset_gpio)) { + dm_gpio_set_value(&reset_gpio, 1); + mdelay(200); + } +#else + debug("PCIE Reset on GPIO support is missing\n"); +#endif /* CONFIG_DM_GPIO */ pcie->first_busno = dev->seq;