From: Fabio Estevam <fabio.estevam@freescale.com>
Date: Fri, 14 Sep 2012 12:14:54 +0000 (+0000)
Subject: mx35pdk: README: Remove NAND references
X-Git-Tag: v2012.10-rc1~2^2^2
X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=1d9b033269263a69f7402f508c17b242fc7fea43;p=u-boot

mx35pdk: README: Remove NAND references

Booting from NAND is currently not supported, so remove its references.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---

diff --git a/board/freescale/mx35pdk/README b/board/freescale/mx35pdk/README
index 3d69ed5839..7232b53357 100644
--- a/board/freescale/mx35pdk/README
+++ b/board/freescale/mx35pdk/README
@@ -71,91 +71,17 @@ exec -c "noinitrd console=ttymxc0,115200 root=/dev/nfsroot rootfstype=nfsroot nf
 Flashing U-Boot
 --------------------------------
 
-There are two options: the original bootloader in NAND can be replaced with
-u-boot, or u-boot can be stored on the NOR flash without erasing
-the delivered bootloader.
+U-boot should be stored on the NOR flash.
+
 The boot storage can be select using the switches on the personality board
 (SW1-SW2) and on the DEBUG board (SW4-SW10).
 
-The second option is to be preferred if you have not a JTAG debugger.
 If something goes wrong flashing the bootloader, it is always possible to
 recover the board booting from the other device.
 
-Replacing the bootloader on the NAND
---------------------------------------
-To replace RedBoot with U-Boot, the easy way is to do this in linux.
-Start the kernel with the suggested options. Make sure to have set the
-mtdparts exactly as described, because this matches the layout on the
-mx35pdk.
-
-You should see in your boot log the following entries for the NAND
-flash:
-
-5 cmdlinepart partitions found on MTD device mxc_nand
-Creating 5 MTD partitions on "mxc_nand":
-0x000000000000-0x000000100000 : "boot"
-0x000000100000-0x000000600000 : "linux"
-0x000000600000-0x000006600000 : "root"
-0x000006600000-0x000006e00000 : "cfg"
-0x000006e00000-0x000080000000 : "user"
-
-You can use the utilities flash_eraseall and nandwrite to put
-u-boot on the NAND. The bootloader is marked as "boot", and 1MB is
-reserved. If everything is correct, this partition is accessed as
-/dev/mtd4. However, check if it is correct with "cat /proc/mtd" and
-get the device node from the partition name:
-
-$ cat /proc/mtd | grep boot
-
-I suggest you try the utilities on a different partition to be sure
-if everything works correctly. If not, and you remove RedBoot, you have to
-reinstall it using the ATK tool as suggested by Freescale, or using a
-JTAG debugger.
-
-I report the versions of the utilities I used (they are provided with ELDK):
-
--bash-3.2# nandwrite --version
-nandwrite $Revision: 1.32 $
-
-flash_eraseall --version
-flash_eraseall $Revision: 1.22 $
-
-nandwrite reports a warning if the file to be saved is not sector aligned.
-This should have no consequences, but I preferred to pad u-boot.bin
-to get no problem at all.
-$ dd if=/dev/zero of=zeros bs=1 count=74800
-$ cat u-boot.bin zeros > u-boot-padded.bin
-
-To erase the partition:
-$ flash_eraseall /dev/mtd4
-
-Writing u-boot:
-
-$ nandwrite /dev/mtd4 u-boot-padded.bin
-
-Now U-Boot is stored on the booting partition.
-
-To boot from NAND, you have to select the switches as follows:
-
-Personality board
-	SW2	1, 4, 5 on
-		2, 3, 6, 7, 8 off
-	SW1	all off
-
-Debug Board:
-	SW5	0
-	SW6	0
-	SW7	0
-	SW8	1
-	SW9	1
-	SW10	0
-
-
 Saving U-Boot in the NOR flash
 ---------------------------------
 
-The procedure to save in the NOR flash is quite the same as to write into the NAND.
-
 Check the partition for boot in the NOR flash. Setting the mtdparts as reported,
 the boot partition should be /dev/mtd0.