From: richardbarry Date: Mon, 25 Apr 2011 14:44:55 +0000 (+0000) Subject: Add in the Microsemi timer driver to provide a time base for the run time stats. X-Git-Tag: V7.0.1~35 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=2cd32a6c750b52e00f6a93999d7cb1424ed06490;p=freertos Add in the Microsemi timer driver to provide a time base for the run time stats. git-svn-id: https://svn.code.sf.net/p/freertos/code/trunk@1389 1d2547de-c912-0410-9cb9-b8ca96c0e9e2 --- diff --git a/Demo/CORTEX_A2F200_IAR_and_Keil/MicroSemi_Code/drivers/mss_timer/mss_timer.h b/Demo/CORTEX_A2F200_IAR_and_Keil/MicroSemi_Code/drivers/mss_timer/mss_timer.h new file mode 100644 index 000000000..d83519d54 --- /dev/null +++ b/Demo/CORTEX_A2F200_IAR_and_Keil/MicroSemi_Code/drivers/mss_timer/mss_timer.h @@ -0,0 +1,598 @@ +/******************************************************************************* + * (c) Copyright 2009 Actel Corporation. All rights reserved. + * + * SmartFusion microcontroller subsystem (MSS) timer driver API. + * + * SVN $Revision: 2661 $ + * SVN $Date: 2010-04-19 17:14:26 +0100 (Mon, 19 Apr 2010) $ + */ +/*=========================================================================*//** + @mainpage SmartFusion MSS Timer Bare Metal Driver. + + @section intro_sec Introduction + The SmartFusion Microcontroller Subsystem (MSS) includes a timer hardware + block which can be used as two independent 32-bits timers or as a single + 64-bits timer in periodic or one-shot mode. + + This driver provides a set of functions for controlling the MSS timer as part + of a bare metal system where no operating system is available. These drivers + can be adapted for use as part of an operating system but the implementation + of the adaptation layer between this driver and the operating system's driver + model is outside the scope of this driver. + + @section theory_op Theory of Operation + The MSS Timer driver uses the SmartFusion "Cortex Microcontroler Software + Interface Standard - Peripheral Access Layer" (CMSIS-PAL) to access hadware + registers. You must ensure that the SmartFusion CMSIS-PAL is either included + in the software toolchain used to build your project or is included in your + project. The most up-to-date SmartFusion CMSIS-PAL files can be obtained using + the Actel Firmware Catalog. + The SmartFusion MSS Timer can be used in one of two mutually exclusive modes; + either as a single 64-bits timer or as two independent 32-bits timers. The MSS + Timer can be used in either periodic mode or one-shot mode. A timer configured + for periodic mode operations will generate an interrupt and reload its + down-counter when it reaches 0. The timer will then continue decrementing from + its reload value without waiting for the interrupt to be cleared. A timer + configured for one-shot mode will only generate an interrupt once when its + down-counter reaches 0. It must be explitcitly reloaded to start decrementing + again. + + The MSS Timer driver functions are grouped into the following categories: + - Initialization and Configuration + - Timer control + - Interrupt control + + The MSS Timer driver provides three initialization functions: + - MSS_TIM1_init() + - MSS_TIM2_init() + - MSS_TIM64_init() + The MSS Timer driver is initialized through calls to these functions and at + least one of them must be called before any other MSS Timer driver functions + can be called. + You should only use the MSS_TIM1_init() and MSS_TIM2_init() functions if you + intend to use the timer in 32-bits mode. Use the MSS_TIM64_init() function is + you intend to use the MSS Timer as a single 64-bits timer. The initialization + functions take a single parameter specifying the operating mode of the timer + being initialized. + + Once initialized a timer can be controlled using the following functions: + - MSS_TIM1_load_immediate() + - MSS_TIM1_load_background() + - MSS_TIM1_get_current_value() + - MSS_TIM1_start() + - MSS_TIM1_stop() + - MSS_TIM2_load_immediate() + - MSS_TIM2_load_background() + - MSS_TIM2_get_current_value() + - MSS_TIM2_start() + - MSS_TIM2_stop() + - MSS_TIM64_load_immediate() + - MSS_TIM64_load_background() + - MSS_TIM64_get_current_value() + - MSS_TIM64_start() + - MSS_TIM64_stop() + + Timer interrupts are controlled using the following functions: + - MSS_TIM1_enable_irq() + - MSS_TIM1_disable_irq() + - MSS_TIM1_clear_irq() + - MSS_TIM2_enable_irq() + - MSS_TIM2_disable_irq() + - MSS_TIM2_clear_irq() + - MSS_TIM64_enable_irq() + - MSS_TIM64_disable_irq() + - MSS_TIM64_clear_irq() + + The function prototypes for the timer interrupt handlers are: + - void Timer1_IRQHandler( void ) + - void Timer2_IRQHandler( void ) + Entries for these interrupt handlers are provided in the SmartFusion CMSIS-PAL + vector table. To add a Timer 1 interrupt handler, you must implement a + Timer1_IRQHandler( ) function as part of your application code. To add a + Timer 2 interrupt handler, you must implement a Timer2_IRQHandler( ) function + as part of your application code. When using the MSS Timer as a 64-bit timer, + you must implement a Timer1_IRQHandler( ) function as part of your + application code. The Timer 2 interrupt is not used when the MSS Timer is + configured as a 64-bit timer. + + *//*=========================================================================*/ +#ifndef MSS_TIMER_H_ +#define MSS_TIMER_H_ + + +#include "../../CMSIS/a2fxxxm3.h" + +#ifdef __cplusplus +extern "C" { +#endif + +/*-------------------------------------------------------------------------*//** + * Timer mode selection. This enumeration is used to select between the two + * possible timer modes of operation: periodic and one-shot mode. It is used as + * an argument to the MSS_TIM1_init(), MSS_TIM2_init() and MSS_TIM64_init() + * functions. + * MSS_TIMER_PERIODIC_MODE: + * In periodic mode the timer generates interrupts at constant intervals. On + * reaching zero, the timer's counter is reloaded with a value held in a + * register and begins counting down again. + * MSS_TIMER_ONE_SHOT_MODE: + * The timer generates a single interrupt in this mode. On reaching zero, the + * timer's counter halts until reprogrammed by the user. + */ +typedef enum __mss_timer_mode_t +{ + MSS_TIMER_PERIODIC_MODE = 0, + MSS_TIMER_ONE_SHOT_MODE = 1 +} mss_timer_mode_t; + +/*-------------------------------------------------------------------------*//** + The MSS_TIM1_init() function initializes the SmartFusion MSS Timer block for + use as a 32-bit timer and selects the operating mode for Timer 1. This function + takes the MSS Timer block out of reset in case this hasn’t been done already, + stops Timer 1, disables its interrupt and sets the Timer 1 operating mode. + Please note that the SmartFusion MSS Timer block cannot be used both as a + 64-bit and 32-bit timer. Calling MSS_TIM1_init() will overwrite any previous + configuration of the MSS Timer as a 64-bit timer. + + + @param mode + The mode parameter specifies whether the timer will operate in periodic or + one-shot mode. Allowed values for this parameter are: + - MSS_TIMER_PERIODIC_MODE + - MSS_TIMER_ONE_SHOT_MODE + */ +static __INLINE void MSS_TIM1_init( mss_timer_mode_t mode ) +{ + NVIC_DisableIRQ( Timer1_IRQn ); /* Disable timer 1 irq in the Cortex-M3 NVIC */ + + SYSREG->SOFT_RST_CR &= ~SYSREG_TIMER_SOFTRESET_MASK; /* Take timer block out of reset */ + + TIMER->TIM64_MODE = 0U; /* switch to 32 bits mode */ + + TIMER_BITBAND->TIM1ENABLE = 0U; /* disable timer */ + TIMER_BITBAND->TIM1INTEN = 0U; /* disable interrupt */ + TIMER_BITBAND->TIM1MODE = (uint32_t)mode; /* set mode (continuous/one-shot) */ + + TIMER->TIM1_RIS = 1U; /* clear timer 1 interrupt */ + NVIC_ClearPendingIRQ( Timer1_IRQn ); /* clear timer 1 interrupt within NVIC */ +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM1_start() function enables Timer 1 and starts its down-counter + decrementing from the load_value specified in previous calls to the + MSS_TIM1_load_immediate() or MSS_TIM1_load_background() functions. + */ +static __INLINE void MSS_TIM1_start( void ) +{ + TIMER_BITBAND->TIM1ENABLE = 1U; /* enable timer */ +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM1_stop() function disables Timer 1 and stops its down-counter + decrementing. + */ +static __INLINE void MSS_TIM1_stop( void ) +{ + TIMER_BITBAND->TIM1ENABLE = 0U; /* disable timer */ +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM1_get_current_value() returns the current value of the Timer 1 + down-counter. + + @return + This function returns the 32-bits current value of the Timer 1 down-counter. + */ +static __INLINE uint32_t MSS_TIM1_get_current_value( void ) +{ + return TIMER->TIM1_VAL; +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM1_load_immediate() function loads the value passed by the + load_value parameter into the Timer 1 down-counter. The counter will decrement + immediately from this value once Timer 1 is enabled. The MSS Timer will + generate an interrupt when the counter reaches zero if Timer 1 interrupts are + enabled. This function is intended to be used when Timer 1 is configured for + one-shot mode to time a single delay. + + @param load_value + The load_value parameter specifies the value from which the Timer 1 down-counter + will start decrementing from. + */ +static __INLINE void MSS_TIM1_load_immediate( uint32_t load_value ) +{ + TIMER->TIM1_LOADVAL = load_value; +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM1_load_background() function is used to specify the value that will + be reloaded into the Timer 1 down-counter the next time the counter reaches + zero. This function is typically used when Timer 1 is configured for periodic + mode operation to select or change the delay period between the interrupts + generated by Timer 1. + + @param load_value + The load_value parameter specifies the value that will be loaded into the + Timer 1 down-counter the next time the down-counter reaches zero. The Timer + 1 down-counter will start decrementing from this value after the current + count expires. + */ +static __INLINE void MSS_TIM1_load_background( uint32_t load_value ) +{ + TIMER->TIM1_BGLOADVAL = load_value; +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM1_enable_irq() function is used to enable interrupt generation for + Timer 1. This function also enables the interrupt in the Cortex-M3 interrupt + controller. The Timer1_IRQHandler() function will be called when a Timer 1 + interrupt occurs. + Note: Note: A Timer1_IRQHandler() default implementation is defined, with + weak linkage, in the SmartFusion CMSIS-PAL. You must provide your own + implementation of the Timer1_IRQHandler() function, that will override the + default implementation, to suit your application. + + */ +static __INLINE void MSS_TIM1_enable_irq( void ) +{ + TIMER_BITBAND->TIM1INTEN = 1U; + NVIC_EnableIRQ( Timer1_IRQn ); +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM1_disable_irq() function is used to disable interrupt generation + for Timer 1. This function also disables the interrupt in the Cortex-M3 + interrupt controller. + */ +static __INLINE void MSS_TIM1_disable_irq( void ) +{ + TIMER_BITBAND->TIM1INTEN = 0U; + NVIC_DisableIRQ( Timer1_IRQn ); +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM1_clear_irq() function is used to clear a pending interrupt from + Timer 1. This function also clears the interrupt in the Cortex-M3 interrupt + controller. + Note: You must call the MSS_TIM1_clear_irq() function as part of your + implementation of the Timer1_IRQHandler() Timer 1 interrupt service routine + (ISR) in order to prevent the same interrupt event retriggering a call to the + ISR. + + */ +static __INLINE void MSS_TIM1_clear_irq( void ) +{ + TIMER->TIM1_RIS = 1U; + NVIC_ClearPendingIRQ( Timer1_IRQn ); +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM2_init() function initializes the SmartFusion MSS Timer block for + use as a 32-bit timer and selects the operating mode for Timer 2. This function + takes the MSS Timer block out of reset in case this hasn’t been done already, + stops Timer 2, disables its interrupt and sets the Timer 2 operating mode. + Note: Please note that the SmartFusion MSS Timer block cannot be used both as + a 64-bit and 32-bit timer. Calling MSS_TIM2_init() will overwrite any previous + configuration of the MSS Timer as a 64-bit timer. + + @param mode + The mode parameter specifies whether the timer will operate in periodic or + one-shot mode. Allowed values for this parameter are: + - MSS_TIMER_PERIODIC_MODE + - MSS_TIMER_ONE_SHOT_MODE + */ +static __INLINE void MSS_TIM2_init( mss_timer_mode_t mode ) +{ + NVIC_DisableIRQ( Timer2_IRQn ); /* Disable timer 2 irq in the Cortex-M3 NVIC */ + + SYSREG->SOFT_RST_CR &= ~SYSREG_TIMER_SOFTRESET_MASK; /* Take timer block out of reset */ + + TIMER->TIM64_MODE = 0U; /* switch to 32 bits mode */ + + TIMER_BITBAND->TIM2ENABLE = 0U; /* disable timer */ + TIMER_BITBAND->TIM2INTEN = 0U; /* disable interrupt */ + TIMER_BITBAND->TIM2MODE = (uint32_t)mode; /* set mode (continuous/one-shot) */ + + TIMER->TIM2_RIS = 1U; /* clear timer 2 interrupt */ + NVIC_ClearPendingIRQ( Timer2_IRQn ); /* clear timer 2 interrupt within NVIC */ +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM2_start() function enables Timer 2 and starts its down-counter + decrementing from the load_value specified in previous calls to the + MSS_TIM2_load_immediate() or MSS_TIM2_load_background() functions. + */ +static __INLINE void MSS_TIM2_start( void ) +{ + TIMER_BITBAND->TIM2ENABLE = 1U; /* enable timer */ +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM2_stop() function disables Timer 2 and stops its down-counter + decrementing. + */ +static __INLINE void MSS_TIM2_stop( void ) +{ + TIMER_BITBAND->TIM2ENABLE = 0U; /* disable timer */ +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM2_get_current_value() returns the current value of the Timer 2 + down-counter. + */ +static __INLINE uint32_t MSS_TIM2_get_current_value( void ) +{ + return TIMER->TIM2_VAL; +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM2_load_immediate() function loads the value passed by the + load_value parameter into the Timer 2 down-counter. The counter will decrement + immediately from this value once Timer 2 is enabled. The MSS Timer will + generate an interrupt when the counter reaches zero if Timer 2 interrupts are + enabled. This function is intended to be used when Timer 2 is configured for + one-shot mode to time a single delay. + + @param load_value + The load_value parameter specifies the value from which the Timer 2 + down-counter will start decrementing. + */ +static __INLINE void MSS_TIM2_load_immediate( uint32_t load_value ) +{ + TIMER->TIM2_LOADVAL = load_value; +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM2_load_background() function is used to specify the value that will + be reloaded into the Timer 2 down-counter the next time the counter reaches + zero. This function is typically used when Timer 2 is configured for periodic + mode operation to select or change the delay period between the interrupts + generated by Timer 2. + + @param load_value + The load_value parameter specifies the value that will be loaded into the + Timer 2 down-counter the next time the down-counter reaches zero. The Timer + 2 down-counter will start decrementing from this value after the current + count expires. + */ +static __INLINE void MSS_TIM2_load_background( uint32_t load_value ) +{ + TIMER->TIM2_BGLOADVAL = load_value; +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM2_enable_irq() function is used to enable interrupt generation for + Timer 2. This function also enables the interrupt in the Cortex-M3 interrupt + controller. The Timer2_IRQHandler() function will be called when a Timer 2 + interrupt occurs. + Note: A Timer2_IRQHandler() default implementation is defined, with weak + linkage, in the SmartFusion CMSIS-PAL. You must provide your own implementation + of the Timer2_IRQHandler() function, that will override the default + implementation, to suit your application. + */ +static __INLINE void MSS_TIM2_enable_irq( void ) +{ + TIMER_BITBAND->TIM2INTEN = 1U; + NVIC_EnableIRQ( Timer2_IRQn ); +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM2_disable_irq() function is used to disable interrupt generation + for Timer 2. This function also disables the interrupt in the Cortex-M3 + interrupt controller. + */ +static __INLINE void MSS_TIM2_disable_irq( void ) +{ + TIMER_BITBAND->TIM2INTEN = 0U; + NVIC_DisableIRQ( Timer2_IRQn ); +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM2_clear_irq() function is used to clear a pending interrupt from + Timer 2. This function also clears the interrupt in the Cortex-M3 interrupt + controller. + Note: You must call the MSS_TIM2_clear_irq() function as part of your + implementation of the Timer2_IRQHandler() Timer 2 interrupt service routine + (ISR) in order to prevent the same interrupt event retriggering a call to the + ISR. + */ +static __INLINE void MSS_TIM2_clear_irq( void ) +{ + TIMER->TIM2_RIS = 1U; + NVIC_ClearPendingIRQ( Timer2_IRQn ); +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM64_init() function initializes the SmartFusion MSS Timer block for + use as a single 64-bit timer and selects the operating mode of the timer. This + function takes the MSS Timer block out of reset in case this hasn’t been done + already, stops the timer, disables its interrupts and sets the timer's + operating mode. + Note: Please note that the SmartFusion MSS Timer block cannot be used both as + a 64-bit and 32-bit timer. Calling MSS_TIM64_init() will overwrite any previous + configuration of the MSS Timer as a 32-bit timer. + + @param mode + The mode parameter specifies whether the timer will operate in periodic or + one-shot mode. Allowed values for this parameter are: + - MSS_TIMER_PERIODIC_MODE + - MSS_TIMER_ONE_SHOT_MODE + */ +static __INLINE void MSS_TIM64_init( mss_timer_mode_t mode ) +{ + NVIC_DisableIRQ( Timer1_IRQn ); /* disable timer 1 interrupt within NVIC */ + NVIC_DisableIRQ( Timer2_IRQn ); /* disable timer 2 interrupt within NVIC */ + + SYSREG->SOFT_RST_CR &= ~SYSREG_TIMER_SOFTRESET_MASK; /* Take timer block out of reset */ + + TIMER->TIM64_MODE = 1U; /* switch to 64 bits mode */ + + TIMER_BITBAND->TIM64ENABLE = 0U; /* disable timer */ + TIMER_BITBAND->TIM64INTEN = 0U; /* disable interrupt */ + TIMER_BITBAND->TIM64MODE = (uint32_t)mode; /* set mode (continuous/one-shot) */ + + TIMER->TIM1_RIS = 1U; /* clear timer 1 interrupt */ + TIMER->TIM2_RIS = 1U; /* clear timer 2 interrupt */ + NVIC_ClearPendingIRQ( Timer1_IRQn ); /* clear timer 1 interrupt within NVIC */ + NVIC_ClearPendingIRQ( Timer2_IRQn ); /* clear timer 2 interrupt within NVIC */ +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM64_start() function enables the 64-bit timer and starts its + down-counter decrementing from the load_value specified in previous calls to + the MSS_TIM64_load_immediate() or MSS_TIM64_load_background() functions. + */ +static __INLINE void MSS_TIM64_start( void ) +{ + TIMER_BITBAND->TIM64ENABLE = 1U; /* enable timer */ +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM64_stop() function disables the 64-bit timer and stops its + down-counter decrementing. + */ +static __INLINE void MSS_TIM64_stop( void ) +{ + TIMER_BITBAND->TIM64ENABLE = 0U; /* disable timer */ +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM64_get_current_value() is used to read the current value of the + 64-bit timer down-counter. + + @param load_value_u + The load_value_u parameter is a pointer to a 32-bit variable where the upper + 32 bits of the current value of the 64-bit timer down-counter will be copied. + + @param load_value_l + The load_value_l parameter is a pointer to a 32-bit variable where the lower + 32 bits of the current value of the 64-bit timer down-counter will be copied. + + Example: + @code + uint32_t current_value_u = 0; + uint32_t current_value_l = 0; + MSS_TIM64_get_current_value( ¤t_value_u, ¤t_value_l ); + @endcode + */ +static __INLINE void MSS_TIM64_get_current_value +( + uint32_t * load_value_u, + uint32_t * load_value_l +) +{ + *load_value_l = TIMER->TIM64_VAL_L; + *load_value_u = TIMER->TIM64_VAL_U; +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM64_load_immediate() function loads the values passed by the + load_value_u and load_value_l parameters into the 64-bit timer down-counter. + The counter will decrement immediately from the concatenated 64-bit value once + the 64-bit timer is enabled. The MSS Timer will generate an interrupt when the + counter reaches zero if 64-bit timer interrupts are enabled. This function is + intended to be used when the 64-bit timer is configured for one-shot mode to + time a single delay. + + @param load_value_u + The load_value_u parameter specifies the upper 32 bits of the 64-bit timer + load value from which the 64-bit timer down-counter will start decrementing. + + @param load_value_l + The load_value_l parameter specifies the lower 32 bits of the 64-bit timer + load value from which the 64-bit timer down-counter will start decrementing. + */ +static __INLINE void MSS_TIM64_load_immediate +( + uint32_t load_value_u, + uint32_t load_value_l +) +{ + TIMER->TIM64_LOADVAL_U = load_value_u; + TIMER->TIM64_LOADVAL_L = load_value_l; +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM64_load_background() function is used to specify the 64-bit value + that will be reloaded into the 64-bit timer down-counter the next time the + counter reaches zero. This function is typically used when the 64-bit timer is + configured for periodic mode operation to select or change the delay period + between the interrupts generated by the 64-bit timer. + + @param load_value_u + The load_value_u parameter specifies the upper 32 bits of the 64-bit timer + load value. The concatenated 64-bit value formed from load_value_u and + load_value_l will be loaded into the 64-bit timer down-counter the next + time the down-counter reaches zero. The 64-bit timer down-counter will start + decrementing from the concatenated 64-bit value after the current count + expires. + + @param load_value_l + The load_value_l parameter specifies the lower 32 bits of the 64-bit timer + load value. The concatenated 64-bit value formed from load_value_u and + load_value_l will be loaded into the 64-bit timer down-counter the next time + the down-counter reaches zero. The 64-bit timer down-counter will start + decrementing from the concatenated 64-bit value after the current count + expires. + + */ +static __INLINE void MSS_TIM64_load_background +( + uint32_t load_value_u, + uint32_t load_value_l +) +{ + TIMER->TIM64_BGLOADVAL_U = load_value_u; + TIMER->TIM64_BGLOADVAL_L = load_value_l; +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM64_enable_irq() function is used to enable interrupt generation for + the 64-bit timer. This function also enables the interrupt in the Cortex-M3 + interrupt controller. The Timer1_IRQHandler() function will be called when a + 64-bit timer interrupt occurs. + Note: A Timer1_IRQHandler() default implementation is defined, with weak + linkage, in the SmartFusion CMSIS-PAL. You must provide your own + implementation of the Timer1_IRQHandler() function, that will override the + default implementation, to suit your application. + Note: The MSS_TIM64_enable_irq() function enables and uses Timer 1 interrupts + for the 64-bit timer. Timer 2 interrupts remain disabled. + */ +static __INLINE void MSS_TIM64_enable_irq( void ) +{ + TIMER_BITBAND->TIM64INTEN = 1U; + NVIC_EnableIRQ( Timer1_IRQn ); +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM64_disable_irq() function is used to disable interrupt generation + for the 64-bit timer. This function also disables the interrupt in the + Cortex-M3 interrupt controller. + */ +static __INLINE void MSS_TIM64_disable_irq( void ) +{ + TIMER_BITBAND->TIM64INTEN = 0U; + NVIC_DisableIRQ( Timer1_IRQn ); +} + +/*-------------------------------------------------------------------------*//** + The MSS_TIM64_clear_irq() function is used to clear a pending interrupt from + the 64-bit timer. This function also clears the interrupt in the Cortex-M3 + interrupt controller. + Note: You must call the MSS_TIM64_clear_irq() function as part of your + implementation of the Timer1_IRQHandler() 64-bit timer interrupt service + routine (ISR) in order to prevent the same interrupt event retriggering a + call to the ISR. + */ +static __INLINE void MSS_TIM64_clear_irq( void ) +{ + TIMER->TIM64_RIS = 1U; + NVIC_ClearPendingIRQ( Timer1_IRQn ); +} + +#ifdef __cplusplus +} +#endif + +#endif /*MSS_TIMER_H_*/