From: Stefan Roese Date: Tue, 4 Mar 2014 14:34:35 +0000 (+0100) Subject: ppc4xx: Remove 4xx NAND booting support X-Git-Tag: v2014.04-rc2~21 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=345b77ba;p=u-boot ppc4xx: Remove 4xx NAND booting support As ppc4xx currently only supports the deprecated nand_spl infrastructure and nobody seems to have time / resources to port this over to the newer SPL infrastructure, lets remove NAND booting completely. This should not affect the "normal", non NAND-booting ppc4xx platforms that are currently supported. Signed-off-by: Stefan Roese Cc: Wolfgang Denk Cc: Tirumala Marri Cc: Matthias Fuchs Cc: Masahiro Yamada Cc: Tom Rini Tested-by: Matthias Fuchs --- diff --git a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c index fe928db039..f8d03cba2d 100644 --- a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c +++ b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c @@ -49,7 +49,6 @@ "SDRAM_" #mnemonic, SDRAM_##mnemonic, data); \ } while (0) -#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) static void update_rdcc(void) { u32 val; @@ -72,7 +71,6 @@ static void update_rdcc(void) } } } -#endif #if defined(CONFIG_440) /* @@ -101,7 +99,6 @@ void dcbz_area(u32 start_address, u32 num_bytes); #define MULDIV64(m1, m2, d) (u32)(((u64)(m1) * (u64)(m2)) / (u64)(d)) -#if !defined(CONFIG_NAND_SPL) /*-----------------------------------------------------------------------------+ * sdram_memsize *-----------------------------------------------------------------------------*/ @@ -217,7 +214,6 @@ void board_add_ram_info(int use_default) val = (val & SDRAM_MMODE_DCL_MASK) >> 4; printf(", CL%d)", val); } -#endif /* !CONFIG_NAND_SPL */ #if defined(CONFIG_SPD_EEPROM) @@ -2843,16 +2839,6 @@ static void test(void) *---------------------------------------------------------------------------*/ phys_size_t initdram(int board_type) { - /* - * Only run this SDRAM init code once. For NAND booting - * targets like Kilauea, we call initdram() early from the - * 4k NAND booting image (CONFIG_NAND_SPL) from nand_boot(). - * Later on the NAND U-Boot image runs (CONFIG_NAND_U_BOOT) - * which calls initdram() again. This time the controller - * mustn't be reconfigured again since we're already running - * from SDRAM. - */ -#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) unsigned long val; #if defined(CONFIG_440) @@ -2969,12 +2955,10 @@ phys_size_t initdram(int board_type) #endif #if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) /*------------------------------------------------------------------ | DQS calibration. +-----------------------------------------------------------------*/ DQS_autocalibration(); -#endif /* !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) */ #endif /* CONFIG_PPC4xx_DDR_AUTOCALIBRATION */ /* @@ -3009,13 +2993,10 @@ phys_size_t initdram(int board_type) set_mcsr(get_mcsr()); #endif /* CONFIG_PPC4xx_DDR_AUTOCALIBRATION */ -#endif /* !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */ - return (CONFIG_SYS_MBYTES_SDRAM << 20); } #endif /* CONFIG_SPD_EEPROM */ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #if defined(CONFIG_440) u32 mfdcr_any(u32 dcr) { @@ -3062,7 +3043,6 @@ void mtdcr_any(u32 dcr, u32 val) } } #endif /* defined(CONFIG_440) */ -#endif /* !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) */ inline void ppc4xx_ibm_ddr2_register_dump(void) { diff --git a/arch/powerpc/cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c b/arch/powerpc/cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c index 82823147fe..67f149deef 100644 --- a/arch/powerpc/cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c +++ b/arch/powerpc/cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c @@ -27,12 +27,6 @@ #include "ecc.h" -/* - * Only compile the DDR auto-calibration code for NOR boot and - * not for NAND boot (NAND SPL and NAND U-Boot - NUB) - */ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) - #define MAXBXCF 4 #define SDRAM_RXBAS_SHIFT_1M 20 @@ -1231,9 +1225,3 @@ u32 DQS_autocalibration(void) return 0; } -#else /* defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */ -u32 DQS_autocalibration(void) -{ - return 0; -} -#endif /* !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) */ diff --git a/arch/powerpc/cpu/ppc4xx/Makefile b/arch/powerpc/cpu/ppc4xx/Makefile index 14b520ff9c..4b792ae2d2 100644 --- a/arch/powerpc/cpu/ppc4xx/Makefile +++ b/arch/powerpc/cpu/ppc4xx/Makefile @@ -14,11 +14,7 @@ obj-y += kgdb.o obj-y += 40x_spd_sdram.o -ifndef CONFIG_NAND_SPL -ifndef CONFIG_NAND_U_BOOT obj-y += 44x_spd_ddr.o -endif -endif obj-$(CONFIG_SDRAM_PPC4xx_IBM_DDR2) += 44x_spd_ddr2.o obj-$(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) += 4xx_ibm_ddr2_autocalib.o obj-y += 4xx_pci.o diff --git a/arch/powerpc/cpu/ppc4xx/start.S b/arch/powerpc/cpu/ppc4xx/start.S index e72c37c75b..11b55d5a56 100644 --- a/arch/powerpc/cpu/ppc4xx/start.S +++ b/arch/powerpc/cpu/ppc4xx/start.S @@ -182,16 +182,13 @@ .extern ext_bus_cntlr_init -#ifdef CONFIG_NAND_U_BOOT - .extern reconfig_tlb0 -#endif /* * Set up GOT: Global Offset Table * * Use r12 to access the GOT */ -#if !defined(CONFIG_NAND_SPL) && !defined(CONFIG_SPL_BUILD) +#if !defined(CONFIG_SPL_BUILD) START_GOT GOT_ENTRY(_GOT2_TABLE_) GOT_ENTRY(_FIXUP_TABLE_) @@ -205,22 +202,7 @@ GOT_ENTRY(__bss_end) GOT_ENTRY(__bss_start) END_GOT -#endif /* CONFIG_NAND_SPL */ - -#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) && \ - !defined(CONFIG_SPL_BUILD) - /* - * NAND U-Boot image is started from offset 0 - */ - .text -#if defined(CONFIG_440) - bl reconfig_tlb0 -#endif - GET_GOT - bl cpu_init_f /* run low-level CPU init code (from Flash) */ - bl board_init_f - /* NOTREACHED - board_init_f() does not return */ -#endif +#endif /* CONFIG_SPL_BUILD */ #if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_BOOT_FROM_XMD) /* @@ -255,9 +237,7 @@ */ #if defined(CONFIG_440) -#if !defined(CONFIG_NAND_SPL) .section .bootpg,"ax" -#endif .globl _start_440 /**************************************************************************/ @@ -511,7 +491,7 @@ tlbnx2: addi r4,r4,1 /* Next TLB */ * r3 - 1st arg to board_init(): IMMP pointer * r4 - 2nd arg to board_init(): boot flag */ -#if !defined(CONFIG_NAND_SPL) && !defined(CONFIG_SPL_BUILD) +#if !defined(CONFIG_SPL_BUILD) .text .long 0x27051956 /* U-Boot Magic Number */ .globl version_string @@ -777,9 +757,6 @@ _start: stwu r1,-8(r1) /* Save back chain and move SP */ stw r0,+12(r1) /* Save return addr (underflow vect) */ -#ifdef CONFIG_NAND_SPL - bl nand_boot_common /* will not return */ -#else #ifndef CONFIG_SPL_BUILD GET_GOT #endif @@ -787,7 +764,6 @@ _start: bl cpu_init_f /* run low-level CPU init code (from Flash) */ bl board_init_f /* NOTREACHED - board_init_f() does not return */ -#endif #endif /* CONFIG_440 */ @@ -1050,9 +1026,6 @@ _start: stw r0, +12(r1) /* Save return addr (underflow vect) */ #endif /* CONFIG_SYS_INIT_DCACHE_CS */ -#ifdef CONFIG_NAND_SPL - bl nand_boot_common /* will not return */ -#else GET_GOT /* initialize GOT access */ bl cpu_init_f /* run low-level CPU init code (from Flash) */ @@ -1060,13 +1033,11 @@ _start: bl board_init_f /* run first part of init code (from Flash) */ /* NOTREACHED - board_init_f() does not return */ -#endif /* CONFIG_NAND_SPL */ - #endif /* CONFIG_405GP || CONFIG_405 || CONFIG_405EP */ /*----------------------------------------------------------------------- */ -#if !defined(CONFIG_NAND_SPL) && !defined(CONFIG_SPL_BUILD) +#if !defined(CONFIG_SPL_BUILD) /* * This code finishes saving the registers to the exception frame * and jumps to the appropriate handler for the exception. @@ -1632,7 +1603,7 @@ __440_msr_continue: blr function_epilog(dcbz_area) #endif /* CONFIG_440 */ -#endif /* CONFIG_NAND_SPL */ +#endif /* CONFIG_SPL_BUILD */ /*------------------------------------------------------------------------------- */ /* Function: in8 */ @@ -1981,75 +1952,3 @@ pll_wait: blr function_epilog(mftlb1) #endif /* CONFIG_440 */ - -#if defined(CONFIG_NAND_SPL) -/* - * void nand_boot_relocate(dst, src, bytes) - * - * r3 = Destination address to copy code to (in SDRAM) - * r4 = Source address to copy code from - * r5 = size to copy in bytes - */ -nand_boot_relocate: - mr r6,r3 - mr r7,r4 - mflr r8 - - /* - * Copy SPL from icache into SDRAM - */ - subi r3,r3,4 - subi r4,r4,4 - srwi r5,r5,2 - mtctr r5 -..spl_loop: - lwzu r0,4(r4) - stwu r0,4(r3) - bdnz ..spl_loop - - /* - * Calculate "corrected" link register, so that we "continue" - * in execution in destination range - */ - sub r3,r7,r6 /* r3 = src - dst */ - sub r8,r8,r3 /* r8 = link-reg - (src - dst) */ - mtlr r8 - blr - -nand_boot_common: - /* - * First initialize SDRAM. It has to be available *before* calling - * nand_boot(). - */ - lis r3,CONFIG_SYS_SDRAM_BASE@h - ori r3,r3,CONFIG_SYS_SDRAM_BASE@l - bl initdram - - /* - * Now copy the 4k SPL code into SDRAM and continue execution - * from there. - */ - lis r3,CONFIG_SYS_NAND_BOOT_SPL_DST@h - ori r3,r3,CONFIG_SYS_NAND_BOOT_SPL_DST@l - lis r4,CONFIG_SYS_NAND_BOOT_SPL_SRC@h - ori r4,r4,CONFIG_SYS_NAND_BOOT_SPL_SRC@l - lis r5,CONFIG_SYS_NAND_BOOT_SPL_SIZE@h - ori r5,r5,CONFIG_SYS_NAND_BOOT_SPL_SIZE@l - bl nand_boot_relocate - - /* - * We're running from SDRAM now!!! - * - * It is necessary for 4xx systems to relocate from running at - * the original location (0xfffffxxx) to somewhere else (SDRAM - * preferably). This is because CS0 needs to be reconfigured for - * NAND access. And we can't reconfigure this CS when currently - * "running" from it. - */ - - /* - * Finally call nand_boot() to load main NAND U-Boot image from - * NAND and jump to it. - */ - bl nand_boot /* will not return */ -#endif /* CONFIG_NAND_SPL */ diff --git a/board/amcc/acadia/memory.c b/board/amcc/acadia/memory.c index 61bfea3fab..9673118857 100644 --- a/board/amcc/acadia/memory.c +++ b/board/amcc/acadia/memory.c @@ -17,7 +17,6 @@ extern void board_pll_init_f(void); -#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) static void cram_bcr_write(u32 wr_val) { wr_val <<= 2; @@ -41,20 +40,9 @@ static void cram_bcr_write(u32 wr_val) return; } -#endif phys_size_t initdram(int board_type) { -#if defined(CONFIG_NAND_SPL) - u32 reg; - - /* don't reinit PLL when booting via I2C bootstrap option */ - mfsdr(SDR0_PINSTP, reg); - if (reg != 0xf0000000) - board_pll_init_f(); -#endif - -#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) int i; u32 val; @@ -88,7 +76,6 @@ phys_size_t initdram(int board_type) /* Wait a short while, since for NAND booting this is too fast */ for (i=0; i<200000; i++) ; -#endif return (CONFIG_SYS_MBYTES_RAM << 20); } diff --git a/board/amcc/acadia/pll.c b/board/amcc/acadia/pll.c index d74b725ae5..d868582ba9 100644 --- a/board/amcc/acadia/pll.c +++ b/board/amcc/acadia/pll.c @@ -135,45 +135,3 @@ void board_pll_init_f(void) mtcpr(CPR0_CLKUP, 0x40000000); } #endif /* CPU__405EZ */ - -#if defined(CONFIG_NAND_SPL) || defined(CONFIG_SPI_SPL) -/* - * Get timebase clock frequency - */ -unsigned long get_tbclk(void) -{ - unsigned long cpr_plld; - unsigned long cpr_primad; - unsigned long primad_cpudv; - unsigned long pllFbkDiv; - unsigned long freqProcessor; - - /* - * Read PLL Mode registers - */ - mfcpr(CPR0_PLLD, cpr_plld); - - /* - * Read CPR_PRIMAD register - */ - mfcpr(CPR0_PRIMAD, cpr_primad); - - /* - * Determine CPU clock frequency - */ - primad_cpudv = ((cpr_primad & PRIMAD_CPUDV_MASK) >> 24); - if (primad_cpudv == 0) - primad_cpudv = 16; - - /* - * Determine FBK_DIV. - */ - pllFbkDiv = ((cpr_plld & PLLD_FBDV_MASK) >> 24); - if (pllFbkDiv == 0) - pllFbkDiv = 256; - - freqProcessor = (CONFIG_SYS_CLK_FREQ * pllFbkDiv) / primad_cpudv; - - return (freqProcessor); -} -#endif /* defined(CONFIG_NAND_SPL) || defined(CONFIG_SPI_SPL) */ diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c index 84bbacf4c5..c8d09636ab 100644 --- a/board/amcc/bamboo/bamboo.c +++ b/board/amcc/bamboo/bamboo.c @@ -16,7 +16,6 @@ void ext_bus_cntlr_init(void); void configure_ppc440ep_pins(void); int is_nand_selected(void); -#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) /************************************************************************* * * Bamboo has one bank onboard sdram (plus DIMM) @@ -178,7 +177,6 @@ const unsigned char cfg_simulate_spd_eeprom[128] = { 0, 0 }; -#endif #if 0 { /* GPIO Alternate1 Alternate2 Alternate3 */ @@ -440,15 +438,11 @@ int checkboard(void) phys_size_t initdram (int board_type) { -#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) long dram_size; dram_size = spd_sdram(); return dram_size; -#else - return CONFIG_SYS_MBYTES_SDRAM << 20; -#endif } /*----------------------------------------------------------------------------+ @@ -1794,23 +1788,12 @@ void configure_ppc440ep_pins(void) if (ppc440ep_core_selection[NAND_FLASH] == CORE_SELECTED) { update_ndfc_ios(gpio_tab); - -#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL | SDR0_CUST0_NDFC_ENABLE | SDR0_CUST0_NDFC_BW_8_BIT | SDR0_CUST0_NDFC_ARE_MASK | SDR0_CUST0_CHIPSELGAT_EN1 | SDR0_CUST0_CHIPSELGAT_EN2); -#else - mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL | - SDR0_CUST0_NDFC_ENABLE | - SDR0_CUST0_NDFC_BW_8_BIT | - SDR0_CUST0_NDFC_ARE_MASK | - SDR0_CUST0_CHIPSELGAT_EN0 | - SDR0_CUST0_CHIPSELGAT_EN2); -#endif - ndfc_selection_in_fpga(); } else diff --git a/board/amcc/bamboo/init.S b/board/amcc/bamboo/init.S index 48dbcbe2a1..5c7c839079 100644 --- a/board/amcc/bamboo/init.S +++ b/board/amcc/bamboo/init.S @@ -32,12 +32,7 @@ tlbtab: * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the * speed up boot process. It is patched after relocation to enable SA_I */ -#ifndef CONFIG_NAND_SPL tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 0, AC_RWX | SA_G) -#else - tlbentry(CONFIG_SYS_NAND_BOOT_SPL_SRC, SZ_4K, CONFIG_SYS_NAND_BOOT_SPL_SRC, 0, AC_RWX | SA_G) - tlbentry(CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, 0, AC_RWX | SA_IG) -#endif /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G) @@ -58,31 +53,3 @@ tlbtab: tlbentry(CONFIG_SYS_USB_DEVICE, SZ_1K, CONFIG_SYS_USB_DEVICE, 0, AC_RW | SA_IG) tlbtab_end - -#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) - /* - * For NAND booting the first TLB has to be reconfigured to full size - * and with caching disabled after running from RAM! - */ -#define TLB00 TLB0(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M) -#define TLB01 TLB1(CONFIG_SYS_BOOT_BASE_ADDR, 0) -#define TLB02 TLB2(AC_RWX | SA_IG) - - .globl reconfig_tlb0 -reconfig_tlb0: - sync - isync - addi r4,r0,0x0000 /* TLB entry #0 */ - lis r5,TLB00@h - ori r5,r5,TLB00@l - tlbwe r5,r4,0x0000 /* Save it out */ - lis r5,TLB01@h - ori r5,r5,TLB01@l - tlbwe r5,r4,0x0001 /* Save it out */ - lis r5,TLB02@h - ori r5,r5,TLB02@l - tlbwe r5,r4,0x0002 /* Save it out */ - sync - isync - blr -#endif diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c index 2b5f1a62cc..79d4babe06 100644 --- a/board/amcc/canyonlands/canyonlands.c +++ b/board/amcc/canyonlands/canyonlands.c @@ -379,11 +379,7 @@ int board_early_init_r (void) */ /* Remap the NOR FLASH to 0xcc00.0000 ... 0xcfff.ffff */ -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) - mtebc(PB3CR, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000); -#else mtebc(PB0CR, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000); -#endif /* Remove TLB entry of boot EBC mapping */ remove_tlb(CONFIG_SYS_BOOT_BASE_ADDR, 16 << 20); diff --git a/board/amcc/canyonlands/init.S b/board/amcc/canyonlands/init.S index d83cd6e754..bf00bd6bca 100644 --- a/board/amcc/canyonlands/init.S +++ b/board/amcc/canyonlands/init.S @@ -31,13 +31,7 @@ tlbtab: * use the speed up boot process. It is patched after relocation to * enable SA_I */ -#ifndef CONFIG_NAND_SPL tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_16M, CONFIG_SYS_BOOT_BASE_ADDR, 4, AC_RWX | SA_G) /* TLB 0 */ -#else - tlbentry(CONFIG_SYS_NAND_BOOT_SPL_SRC, SZ_4K, CONFIG_SYS_NAND_BOOT_SPL_SRC, 4, AC_RWX | SA_G) - tlbentry(CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, 0, AC_RWX | SA_IG) - tlbentry(256 << 20, SZ_256M, 256 << 20, 0, AC_RWX | SA_IG) -#endif /* * TLB entries for SDRAM are not needed on this platform. @@ -95,31 +89,3 @@ tlbtab: #endif tlbtab_end - -#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) - /* - * For NAND booting the first TLB has to be reconfigured to full size - * and with caching disabled after running from RAM! - */ -#define TLB00 TLB0(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M) -#define TLB01 TLB1(CONFIG_SYS_BOOT_BASE_ADDR, 1) -#define TLB02 TLB2(AC_RWX | SA_IG) - - .globl reconfig_tlb0 -reconfig_tlb0: - sync - isync - addi r4,r0,0x0000 /* TLB entry #0 */ - lis r5,TLB00@h - ori r5,r5,TLB00@l - tlbwe r5,r4,0x0000 /* Save it out */ - lis r5,TLB01@h - ori r5,r5,TLB01@l - tlbwe r5,r4,0x0001 /* Save it out */ - lis r5,TLB02@h - ori r5,r5,TLB02@l - tlbwe r5,r4,0x0002 /* Save it out */ - sync - isync - blr -#endif diff --git a/board/amcc/sequoia/init.S b/board/amcc/sequoia/init.S index b31e9db3f9..f876639d35 100644 --- a/board/amcc/sequoia/init.S +++ b/board/amcc/sequoia/init.S @@ -48,11 +48,7 @@ tlbtab: /* BOOT_CS (FLASH) must be forth. Before relocation SA_I can be off to use the * speed up boot process. It is patched after relocation to enable SA_I */ -#ifndef CONFIG_NAND_SPL tlbentry( CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G ) -#else - tlbentry( CONFIG_SYS_NAND_BOOT_SPL_SRC, SZ_4K, CONFIG_SYS_NAND_BOOT_SPL_SRC, 1, AC_RWX | SA_G ) -#endif #ifdef CONFIG_SYS_INIT_RAM_DCACHE /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ @@ -81,31 +77,3 @@ tlbtab: tlbentry(0xE8000000, SZ_64K, 0xE8000000, 1, AC_RWX | SA_IG) tlbtab_end - -#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) - /* - * For NAND booting the first TLB has to be reconfigured to full size - * and with caching disabled after running from RAM! - */ -#define TLB00 TLB0(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M) -#define TLB01 TLB1(CONFIG_SYS_BOOT_BASE_ADDR, 1) -#define TLB02 TLB2(AC_RWX | SA_IG) - - .globl reconfig_tlb0 -reconfig_tlb0: - sync - isync - addi r4,r0,CONFIG_SYS_TLB_FOR_BOOT_FLASH /* TLB entry # */ - lis r5,TLB00@h - ori r5,r5,TLB00@l - tlbwe r5,r4,0x0000 /* Save it out */ - lis r5,TLB01@h - ori r5,r5,TLB01@l - tlbwe r5,r4,0x0001 /* Save it out */ - lis r5,TLB02@h - ori r5,r5,TLB02@l - tlbwe r5,r4,0x0002 /* Save it out */ - sync - isync - blr -#endif diff --git a/board/amcc/sequoia/sdram.c b/board/amcc/sequoia/sdram.c index 2c5a21806a..67640d7edf 100644 --- a/board/amcc/sequoia/sdram.c +++ b/board/amcc/sequoia/sdram.c @@ -26,14 +26,6 @@ extern int denali_wait_for_dlllock(void); extern void denali_core_search_data_eye(void); -#if defined(CONFIG_NAND_SPL) -/* Using arch/powerpc/cpu/ppc4xx/speed.c to calculate the bus frequency is too big - * for the 4k NAND boot image so define bus_frequency to 133MHz here - * which is save for the refresh counter setup. - */ -#define get_bus_freq(val) 133333333 -#endif - /************************************************************************* * * initdram -- 440EPx's DDR controller is a DENALI Core @@ -41,8 +33,7 @@ extern void denali_core_search_data_eye(void); ************************************************************************/ phys_size_t initdram (int board_type) { -#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT)) || \ - defined(CONFIG_NAND_SPL) +#if !defined(CONFIG_SYS_RAMBOOT) ulong speed = get_bus_freq(0); mtsdram(DDR0_02, 0x00000000); @@ -81,7 +72,7 @@ phys_size_t initdram (int board_type) mtsdram(DDR0_02, 0x00000001); denali_wait_for_dlllock(); -#endif /* #ifndef CONFIG_NAND_U_BOOT */ +#endif /* #ifndef CONFIG_SYS_RAMBOOT */ #ifdef CONFIG_DDR_DATA_EYE /* -----------------------------------------------------------+ diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c index 73c65c56aa..53f9b3419f 100644 --- a/board/amcc/sequoia/sequoia.c +++ b/board/amcc/sequoia/sequoia.c @@ -142,8 +142,7 @@ int misc_init_r(void) gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; gd->bd->bi_flashoffset = 0; -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) || \ - defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) mtdcr(EBC0_CFGADDR, PB3CR); #else mtdcr(EBC0_CFGADDR, PB0CR); @@ -151,8 +150,7 @@ int misc_init_r(void) pbcr = mfdcr(EBC0_CFGDATA); size_val = ffs(gd->bd->bi_flashsize) - 21; pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) || \ - defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) mtdcr(EBC0_CFGADDR, PB3CR); #else mtdcr(EBC0_CFGADDR, PB0CR); @@ -360,7 +358,7 @@ void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev) } #endif -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) /* * On NAND-booting sequoia, we need to patch the chips select numbers * in the dtb (CS0 - NAND, CS3 - NOR) @@ -411,4 +409,4 @@ void ft_board_setup(void *blob, bd_t *bd) return; } } -#endif /* CONFIG_NAND_U_BOOT */ +#endif /* CONFIG_SYS_RAMBOOT */ diff --git a/board/esd/pmc440/init.S b/board/esd/pmc440/init.S index cc8030b5e5..1f26fad147 100644 --- a/board/esd/pmc440/init.S +++ b/board/esd/pmc440/init.S @@ -27,11 +27,7 @@ tlbtab: * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the * speed up boot process. It is patched after relocation to enable SA_I */ -#ifndef CONFIG_NAND_SPL tlbentry( CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G ) -#else - tlbentry( CONFIG_SYS_NAND_BOOT_SPL_SRC, SZ_4K, CONFIG_SYS_NAND_BOOT_SPL_SRC, 1, AC_RWX | SA_G ) -#endif /* TLB entries for DDR2 SDRAM are generated dynamically */ @@ -71,31 +67,3 @@ tlbtab: /* TODO: what about high IO space */ tlbtab_end - -#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) - /* - * For NAND booting the first TLB has to be reconfigured to full size - * and with caching disabled after running from RAM! - */ -#define TLB00 TLB0(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M) -#define TLB01 TLB1(CONFIG_SYS_BOOT_BASE_ADDR, 1) -#define TLB02 TLB2(AC_RWX | SA_IG) - - .globl reconfig_tlb0 -reconfig_tlb0: - sync - isync - addi r4,r0,0x0000 /* TLB entry #0 */ - lis r5,TLB00@h - ori r5,r5,TLB00@l - tlbwe r5,r4,0x0000 /* Save it out */ - lis r5,TLB01@h - ori r5,r5,TLB01@l - tlbwe r5,r4,0x0001 /* Save it out */ - lis r5,TLB02@h - ori r5,r5,TLB02@l - tlbwe r5,r4,0x0002 /* Save it out */ - sync - isync - blr -#endif diff --git a/board/esd/pmc440/pmc440.c b/board/esd/pmc440/pmc440.c index 88fc5f77b6..e86996c55f 100644 --- a/board/esd/pmc440/pmc440.c +++ b/board/esd/pmc440/pmc440.c @@ -229,19 +229,11 @@ int misc_init_r(void) gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; gd->bd->bi_flashoffset = 0; -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) - mtdcr(EBC0_CFGADDR, PB2CR); -#else mtdcr(EBC0_CFGADDR, PB0CR); -#endif pbcr = mfdcr(EBC0_CFGDATA); size_val = ffs(gd->bd->bi_flashsize) - 21; pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) - mtdcr(EBC0_CFGADDR, PB2CR); -#else mtdcr(EBC0_CFGADDR, PB0CR); -#endif mtdcr(EBC0_CFGDATA, pbcr); /* diff --git a/boards.cfg b/boards.cfg index 14cd15165c..3664a2e76d 100644 --- a/boards.cfg +++ b/boards.cfg @@ -1121,22 +1121,14 @@ Active powerpc ppc4xx - amcc - Active powerpc ppc4xx - amcc - taihu - John Otken Active powerpc ppc4xx - amcc - taishan - Stefan Roese Active powerpc ppc4xx - amcc - yucca - - -Active powerpc ppc4xx - amcc acadia acadia_nand acadia:NAND_U_BOOT,SYS_TEXT_BASE=0x01000000 Stefan Roese -Active powerpc ppc4xx - amcc bamboo bamboo_nand bamboo:NAND_U_BOOT,SYS_TEXT_BASE=0x01000000 Stefan Roese Active powerpc ppc4xx - amcc canyonlands arches canyonlands:ARCHES Stefan Roese Active powerpc ppc4xx - amcc canyonlands canyonlands canyonlands:CANYONLANDS Stefan Roese -Active powerpc ppc4xx - amcc canyonlands canyonlands_nand canyonlands:CANYONLANDS,NAND_U_BOOT,SYS_TEXT_BASE=0x01000000 Stefan Roese Active powerpc ppc4xx - amcc canyonlands glacier canyonlands:GLACIER Stefan Roese -Active powerpc ppc4xx - amcc canyonlands glacier_nand canyonlands:GLACIER,NAND_U_BOOT,SYS_TEXT_BASE=0x01000000 Stefan Roese Active powerpc ppc4xx - amcc kilauea haleakala kilauea:HALEAKALA Stefan Roese -Active powerpc ppc4xx - amcc kilauea haleakala_nand kilauea:NAND_U_BOOT,SYS_TEXT_BASE=0x01000000 Stefan Roese Active powerpc ppc4xx - amcc kilauea kilauea kilauea:KILAUEA Stefan Roese -Active powerpc ppc4xx - amcc kilauea kilauea_nand kilauea:NAND_U_BOOT,SYS_TEXT_BASE=0x01000000 Stefan Roese Active powerpc ppc4xx - amcc sequoia rainier sequoia:RAINIER Stefan Roese -Active powerpc ppc4xx - amcc sequoia rainier_nand sequoia:RAINIER,NAND_U_BOOT,SYS_TEXT_BASE=0x01000000 Stefan Roese Active powerpc ppc4xx - amcc sequoia rainier_ramboot sequoia:RAINIER,SYS_RAMBOOT,SYS_TEXT_BASE=0x01000000,SYS_LDSCRIPT=board/amcc/sequoia/u-boot-ram.lds Stefan Roese Active powerpc ppc4xx - amcc sequoia sequoia sequoia:SEQUOIA Stefan Roese -Active powerpc ppc4xx - amcc sequoia sequoia_nand sequoia:SEQUOIA,NAND_U_BOOT,SYS_TEXT_BASE=0x01000000 Stefan Roese Active powerpc ppc4xx - amcc sequoia sequoia_ramboot sequoia:SEQUOIA,SYS_RAMBOOT,SYS_TEXT_BASE=0x01000000,SYS_LDSCRIPT=board/amcc/sequoia/u-boot-ram.lds Stefan Roese Active powerpc ppc4xx - amcc walnut sycamore walnut Stefan Roese Active powerpc ppc4xx - amcc walnut walnut - Stefan Roese diff --git a/drivers/mtd/nand/ndfc.c b/drivers/mtd/nand/ndfc.c index 34688e9bef..5510b13c01 100644 --- a/drivers/mtd/nand/ndfc.c +++ b/drivers/mtd/nand/ndfc.c @@ -104,7 +104,6 @@ static void ndfc_read_buf(struct mtd_info *mtdinfo, uint8_t *buf, int len) *p++ = in_be32((u32 *)(base + NDFC_DATA)); } -#ifndef CONFIG_NAND_SPL /* * Don't use these speedup functions in NAND boot image, since the image * has to fit into 4kByte. @@ -148,8 +147,6 @@ static uint8_t ndfc_read_byte(struct mtd_info *mtd) } -#endif /* #ifndef CONFIG_NAND_SPL */ - void board_nand_select_device(struct nand_chip *nand, int chip) { /* @@ -207,21 +204,11 @@ int board_nand_init(struct nand_chip *nand) nand->options |= NAND_BUSWIDTH_16; #endif -#ifndef CONFIG_NAND_SPL nand->write_buf = ndfc_write_buf; nand->verify_buf = ndfc_verify_buf; nand->read_byte = ndfc_read_byte; chip++; -#else - /* - * Setup EBC (CS0 only right now) - */ - mtebc(EBC0_CFG, CONFIG_SYS_NDFC_EBC0_CFG); - - mtebc(PB0CR, CONFIG_SYS_EBC_PB0CR); - mtebc(PB0AP, CONFIG_SYS_EBC_PB0AP); -#endif return 0; } diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h index fd39109daf..c5e2f164ce 100644 --- a/include/configs/PMC440.h +++ b/include/configs/PMC440.h @@ -95,12 +95,7 @@ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */ -#else -#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ -#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */ -#endif /*----------------------------------------------------------------------- * RTC @@ -142,69 +137,10 @@ #define CONFIG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */ #endif -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 4k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 4kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - * On 440EPx the SPL is copied to SDRAM before the NAND controller is - * set up. While still running from cache, I experienced problems accessing - * the NAND controller. sr - 2006-08-25 - */ -#if defined (CONFIG_NAND_U_BOOT) -#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */ -#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ - -/* - * Now the NAND chip has to be defined (no autodetection used!) - */ -#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */ -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ -#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ - -#define CONFIG_SYS_NAND_ECCSIZE 256 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_SYS_NAND_OOBSIZE 16 -#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7} -#endif - -#ifdef CONFIG_ENV_IS_IN_NAND -/* - * For NAND booting the environment is embedded in the U-Boot image. Please take - * look at the file board/amcc/sequoia/u-boot-nand.lds for details. - */ -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#endif - /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ -#endif #define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ /* 440EPx errata CHIP 11 */ @@ -448,7 +384,6 @@ /* * On Sequoia CS0 and CS3 are switched when configuring for NAND booting */ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_SYS_NAND_CS 2 /* NAND chip connected to CSx */ /* Memory Bank 0 (NOR-FLASH) initialization */ @@ -458,16 +393,6 @@ /* Memory Bank 2 (NAND-FLASH) initialization */ #define CONFIG_SYS_EBC_PB2AP 0x018003c0 #define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND_ADDR | 0x1c000) -#else -#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ -/* Memory Bank 2 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x03017200 -#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FLASH_BASE | 0xda000) - -/* Memory Bank 0 (NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x018003c0 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000) -#endif /* Memory Bank 1 (RESET) initialization */ #define CONFIG_SYS_EBC_PB1AP 0x7f817200 /* 0x03017200 */ diff --git a/include/configs/acadia.h b/include/configs/acadia.h index 5f3b5f936f..4dd5720d2f 100644 --- a/include/configs/acadia.h +++ b/include/configs/acadia.h @@ -82,17 +82,11 @@ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#else -#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ -#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */ -#endif /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ @@ -106,16 +100,6 @@ #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#else -/* - * No NOR-flash on Acadia when NAND-booting. We need to undef the - * NOR device-tree fixup code as well, since flash_info is not defined - * in this case. - */ -#define CONFIG_SYS_NO_FLASH 1 -#undef CONFIG_FDT_FIXUP_NOR_FLASH_SIZE -#endif - #ifdef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) @@ -126,61 +110,6 @@ #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #endif -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 4k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 4kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - * On 440EPx the SPL is copied to SDRAM before the NAND controller is - * set up. While still running from cache, I experienced problems accessing - * the NAND controller. sr - 2006-08-25 - */ -#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_DATA_ADDR + (16 << 10)) /* Copy SPL here*/ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */ -#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ - -/* - * Now the NAND chip has to be defined (no autodetection used!) - */ -#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */ -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ -#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ - -#define CONFIG_SYS_NAND_ECCSIZE 256 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_SYS_NAND_OOBSIZE 16 -#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7} - -#ifdef CONFIG_ENV_IS_IN_NAND -/* - * For NAND booting the environment is embedded in the U-Boot image. Please take - * look at the file board/amcc/sequoia/u-boot-nand.lds for details. - */ -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#endif - /*----------------------------------------------------------------------- * RAM (CRAM) *----------------------------------------------------------------------*/ @@ -219,7 +148,6 @@ CONFIG_AMCC_DEF_ENV_POWERPC \ CONFIG_AMCC_DEF_ENV_PPC_OLD \ CONFIG_AMCC_DEF_ENV_NOR_UPD \ - CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fff10000\0" \ "ramdisk_addr=fff20000\0" \ "kozio=bootm ffc60000\0" \ @@ -242,14 +170,6 @@ #define CONFIG_CMD_NAND #define CONFIG_CMD_USB -/* - * No NOR on Acadia when NAND-booting - */ -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) -#undef CONFIG_CMD_FLASH -#undef CONFIG_CMD_IMLS -#endif - /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ @@ -260,7 +180,6 @@ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_SYS_NAND_CS 3 /* Memory Bank 0 (Flash) initialization */ #define CONFIG_SYS_EBC_PB0AP 0x03337200 @@ -278,24 +197,6 @@ /* Memory Bank 2 (CRAM) initialization */ #define CONFIG_SYS_EBC_PB2AP 0x030400c0 #define CONFIG_SYS_EBC_PB2CR 0x020bc000 -#else -#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ -/* Memory Bank 0 (NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x018003c0 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000) - -/* - * When NAND-booting the CRAM EBC setup must be done in sync mode, since the - * NAND-SPL already initialized the CRAM and EBC to sync mode. - */ -/* Memory Bank 1 (CRAM) initialization */ -#define CONFIG_SYS_EBC_PB1AP 0x9C0201C0 -#define CONFIG_SYS_EBC_PB1CR 0x000bc000 - -/* Memory Bank 2 (CRAM) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x9C0201C0 -#define CONFIG_SYS_EBC_PB2CR 0x020bc000 -#endif /* Memory Bank 4 (CPLD) initialization */ #define CONFIG_SYS_EBC_PB4AP 0x04006000 diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h index 0f38c92fa0..2aea89937a 100644 --- a/include/configs/amcc-common.h +++ b/include/configs/amcc-common.h @@ -253,10 +253,4 @@ "cp.b ${fileaddr} " __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ "upd=run load update\0" \ -#define CONFIG_AMCC_DEF_ENV_NAND_UPD \ - "u-boot-nand=" __stringify(CONFIG_HOSTNAME) "/u-boot-nand.bin\0"\ - "nload=tftp 200000 ${u-boot-nand}\0" \ - "nupdate=nand erase 0 100000;nand write 200000 0 100000\0" \ - "nupd=run nload nupdate\0" - #endif /* __AMCC_COMMON_H */ diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index 97da1e9078..6ba4aaf8cb 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -86,12 +86,7 @@ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#else -#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ -#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */ -#endif /*----------------------------------------------------------------------- * FLASH related @@ -120,61 +115,6 @@ #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #endif /* CONFIG_ENV_IS_IN_FLASH */ -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 4k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 4kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - * On 440EPx the SPL is copied to SDRAM before the NAND controller is - * set up. While still running from cache, I experienced problems accessing - * the NAND controller. sr - 2006-08-25 - */ -#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CONFIG_SYS_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */ -#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ - -/* - * Now the NAND chip has to be defined (no autodetection used!) - */ -#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */ -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ -#define CONFIG_SYS_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */ - -#define CONFIG_SYS_NAND_ECCSIZE 256 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_SYS_NAND_OOBSIZE 16 -#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7} - -#ifdef CONFIG_ENV_IS_IN_NAND -/* - * For NAND booting the environment is embedded in the U-Boot image. Please take - * look at the file board/amcc/sequoia/u-boot-nand.lds for details. - */ -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#endif - /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ @@ -182,15 +122,7 @@ #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_ADDR + 2 } #define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ - -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_SYS_NAND_CS 1 -#else -#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ -/* Memory Bank 0 (NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x018003c0 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000) -#endif /*----------------------------------------------------------------------- * DDR SDRAM @@ -226,7 +158,6 @@ CONFIG_AMCC_DEF_ENV_POWERPC \ CONFIG_AMCC_DEF_ENV_PPC_OLD \ CONFIG_AMCC_DEF_ENV_NOR_UPD \ - CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ "" diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index 620a0f5c57..8eeb15c0e1 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -125,78 +125,9 @@ /* * Define here the location of the environment variables (FLASH). */ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #define CONFIG_SYS_NOR_CS 0 /* NOR chip connected to CSx */ #define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */ -#else -#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ -#define CONFIG_SYS_NOR_CS 3 /* NOR chip connected to CSx */ -#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ -#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */ -#endif - -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 4k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 4kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - * On 440EPx the SPL is copied to SDRAM before the NAND controller is - * set up. While still running from cache, I experienced problems accessing - * the NAND controller. sr - 2006-08-25 - * - * This is the first official implementation of booting from 2k page sized - * NAND devices (e.g. Micron 29F2G08AA 256Mbit * 8) - */ -#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from */ - /* this addr */ -#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (1 << 20) /* Size of RAM U-Boot image */ - -/* - * Now the NAND chip has to be defined (no autodetection used!) - */ -#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10) /* NAND chip page size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */ -#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE) - /* NAND chip page count */ -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 /* Location of bad block marker*/ -#define CONFIG_SYS_NAND_5_ADDR_CYCLE /* Fifth addr used (<=128MB) */ - -#define CONFIG_SYS_NAND_ECCSIZE 256 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_SYS_NAND_OOBSIZE 64 -#define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47, \ - 48, 49, 50, 51, 52, 53, 54, 55, \ - 56, 57, 58, 59, 60, 61, 62, 63} - -#ifdef CONFIG_ENV_IS_IN_NAND -/* - * For NAND booting the environment is embedded in the U-Boot image. Please take - * look at the file board/amcc/canyonlands/u-boot-nand.lds for details. - */ -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#endif /*----------------------------------------------------------------------- * FLASH related @@ -235,7 +166,6 @@ /*------------------------------------------------------------------------------ * DDR SDRAM *----------------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) #if !defined(CONFIG_ARCHES) /* * NAND booting U-Boot version uses a fixed initialization, since the whole @@ -308,7 +238,6 @@ #define CONFIG_SYS_SDRAM0_MMODE 0x00000432 #define CONFIG_SYS_SDRAM0_MEMODE 0x00000004 #endif /* !defined(CONFIG_ARCHES) */ -#endif /* !defined(CONFIG_NAND_U_BOOT) */ #define CONFIG_SYS_MBYTES_SDRAM 512 /* 512MB */ @@ -421,7 +350,6 @@ CONFIG_AMCC_DEF_ENV \ CONFIG_AMCC_DEF_ENV_POWERPC \ CONFIG_AMCC_DEF_ENV_NOR_UPD \ - CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ @@ -556,15 +484,6 @@ * 0xfe00.0000 -> 4.ce00.0000 */ -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) -/* Memory Bank 3 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x10055e00 -#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000) - -/* Memory Bank 0 (NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x018003c0 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/ -#else /* Memory Bank 0 (NOR-FLASH) initialization */ #define CONFIG_SYS_EBC_PB0AP 0x10055e00 #define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000) @@ -574,7 +493,6 @@ #define CONFIG_SYS_EBC_PB3AP 0x018003c0 #define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/ #endif -#endif /*defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */ #if !defined(CONFIG_ARCHES) /* Memory Bank 2 (CPLD) initialization */ diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 0695d2d37b..1990b2df15 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -118,12 +118,7 @@ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#else -#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ -#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */ -#endif /*----------------------------------------------------------------------- * FLASH related @@ -151,61 +146,6 @@ #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #endif /* CONFIG_ENV_IS_IN_FLASH */ -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 4k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 4kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - * On 405EX the SPL is copied to SDRAM before the NAND controller is - * set up. While still running from location 0xfffff000...0xffffffff the - * NAND controller cannot be accessed since it is attached to CS0 too. - */ -#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CONFIG_SYS_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */ -#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ - -/* - * Now the NAND chip has to be defined (no autodetection used!) - */ -#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */ -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ -#define CONFIG_SYS_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */ - -#define CONFIG_SYS_NAND_ECCSIZE 256 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_SYS_NAND_OOBSIZE 16 -#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7} - -#ifdef CONFIG_ENV_IS_IN_NAND -/* - * For NAND booting the environment is embedded in the U-Boot image. Please take - * look at the file board/amcc/sequoia/u-boot-nand.lds for details. - */ -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#endif - /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ @@ -230,11 +170,9 @@ * * DDR Autocalibration Method_B is the default. */ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */ #define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */ #undef CONFIG_PPC4xx_DDR_METHOD_A -#endif #define CONFIG_SYS_SDRAM0_MB0CF_BASE (( 0 << 20) + CONFIG_SYS_SDRAM_BASE) @@ -416,7 +354,6 @@ CONFIG_AMCC_DEF_ENV_POWERPC \ CONFIG_AMCC_DEF_ENV_PPC_OLD \ CONFIG_AMCC_DEF_ENV_NOR_UPD \ - CONFIG_AMCC_DEF_ENV_NAND_UPD \ "logversion=2\0" \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ @@ -434,16 +371,7 @@ #define CONFIG_CMD_PCI #define CONFIG_CMD_SNTP -/* - * Don't run the memory POST on the NAND-booting version. It will - * overwrite part of the U-Boot image which is already loaded from NAND - * to SDRAM. - */ -#if defined(CONFIG_NAND_U_BOOT) -#define CONFIG_SYS_POST_MEMORY_ON 0 -#else #define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORY -#endif /* POST support */ #define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ @@ -494,18 +422,6 @@ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) -/* booting from NAND, so NAND chips select has to be on CS 0 */ -#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ - -/* Memory Bank 1 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB1AP 0x05806500 -#define CONFIG_SYS_EBC_PB1CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/ - -/* Memory Bank 0 (NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x018003c0 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1e000) -#else #define CONFIG_SYS_NAND_CS 1 /* NAND chip connected to CSx */ /* Memory Bank 0 (NOR-FLASH) initialization */ @@ -515,7 +431,6 @@ /* Memory Bank 1 (NAND-FLASH) initialization */ #define CONFIG_SYS_EBC_PB1AP 0x018003c0 #define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_ADDR | 0x1e000) -#endif /* Memory Bank 2 (FPGA) initialization */ #define CONFIG_SYS_EBC_PB2AP (EBC_BXAP_BME_ENABLED | \ diff --git a/include/configs/redwood.h b/include/configs/redwood.h index 84d1e584a0..622b7c79e6 100644 --- a/include/configs/redwood.h +++ b/include/configs/redwood.h @@ -120,7 +120,6 @@ CONFIG_AMCC_DEF_ENV \ CONFIG_AMCC_DEF_ENV_POWERPC \ CONFIG_AMCC_DEF_ENV_NOR_UPD \ - CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 0e21ee3dc0..b6a5e6a59c 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -97,10 +97,7 @@ /* * Environment */ -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) -#define CONFIG_ENV_IS_IN_NAND /* use NAND for environ vars */ -#define CONFIG_ENV_IS_EMBEDDED /* use embedded environment */ -#elif defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) #define CONFIG_ENV_IS_NOWHERE /* Store env in memory only */ #define CONFIG_ENV_SIZE (8 << 10) /* @@ -148,68 +145,11 @@ #endif #endif /* CONFIG_CMD_FLASH */ -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 4k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 4kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - * On 440EPx the SPL is copied to SDRAM before the NAND controller is - * set up. While still running from cache, I experienced problems accessing - * the NAND controller. sr - 2006-08-25 - */ -#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from */ - /* this addr */ -#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */ - -/* - * Now the NAND chip has to be defined (no autodetection used!) - */ -#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */ -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ -#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ - -#define CONFIG_SYS_NAND_ECCSIZE 256 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_SYS_NAND_OOBSIZE 16 -#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7} - -#ifdef CONFIG_ENV_IS_IN_NAND -/* - * For NAND booting the environment is embedded in the U-Boot image. Please take - * look at the file board/amcc/sequoia/u-boot-nand.lds for details. - */ -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#endif - /* * DDR SDRAM */ #define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) && \ - !defined(CONFIG_SYS_RAMBOOT) +#if !defined(CONFIG_SYS_RAMBOOT) #define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ #endif #define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ @@ -247,7 +187,6 @@ CONFIG_AMCC_DEF_ENV_POWERPC \ CONFIG_AMCC_DEF_ENV_PPC_OLD \ CONFIG_AMCC_DEF_ENV_NOR_UPD \ - CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=FC000000\0" \ "ramdisk_addr=FC180000\0" \ "" @@ -321,7 +260,7 @@ * overwrite part of the U-Boot image which is already loaded from NAND * to SDRAM. */ -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) #define CONFIG_SYS_POST_MEMORY_ON 0 #else #define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORY @@ -370,8 +309,7 @@ /* * On Sequoia CS0 and CS3 are switched when configuring for NAND booting */ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) && \ - !defined(CONFIG_SYS_RAMBOOT) +#if !defined(CONFIG_SYS_RAMBOOT) #define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */ /* Memory Bank 0 (NOR-FLASH) initialization */ #define CONFIG_SYS_EBC_PB0AP 0x03017200 diff --git a/nand_spl/board/amcc/acadia/Makefile b/nand_spl/board/amcc/acadia/Makefile deleted file mode 100644 index 4d084b313e..0000000000 --- a/nand_spl/board/amcc/acadia/Makefile +++ /dev/null @@ -1,88 +0,0 @@ -# -# (C) Copyright 2007 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk - -nandobj := $(OBJTREE)/nand_spl/ - -LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds -LDFLAGS := -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(LDFLAGS) \ - $(LDFLAGS_FINAL) -asflags-y += -DCONFIG_NAND_SPL -ccflags-y += -DCONFIG_NAND_SPL - -SOBJS = start.o resetvec.o cache.o -COBJS = gpio.o nand_boot.o nand_ecc.o memory.o ndfc.o pll.o - -OBJS := $(addprefix $(obj)/,$(SOBJS) $(COBJS)) -__OBJS := $(SOBJS) $(COBJS) -LNDIR := $(nandobj)board/$(BOARDDIR) - -targets += $(__OBJS) - -all: $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin \ - $(nandobj)System.map - -$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) --pad-to=$(PAD_TO) -O binary $< $@ - -$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) -O binary $< $@ - -$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds - cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \ - -Map $(nandobj)u-boot-spl.map -o $@ - -$(nandobj)System.map: $(nandobj)u-boot-spl - @$(NM) $< | \ - grep -v '\(compiled\)\|\(\.o$$\)\|\( [aUw] \)\|\(\.\.ng$$\)\|\(LASH[RL]DI\)' | \ - sort > $@ - -$(nandobj)u-boot.lds: $(LDSCRIPT) - $(CPP) $(cpp_flags) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ - -# create symbolic links for common files - -# from cpu directory -$(obj)/cache.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/cache.S $@ - -$(obj)/gpio.c: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/gpio.c $@ - -$(obj)/ndfc.c: - @rm -f $@ - ln -s $(SRCTREE)/drivers/mtd/nand/ndfc.c $@ - -$(obj)/resetvec.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/resetvec.S $@ - -$(obj)/start.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/start.S $@ - -# from board directory -$(obj)/memory.c: - @rm -f $@ - ln -s $(SRCTREE)/board/amcc/acadia/memory.c $@ - -$(obj)/pll.c: - @rm -f $@ - ln -s $(SRCTREE)/board/amcc/acadia/pll.c $@ - -# from nand_spl directory -$(obj)/nand_boot.c: - @rm -f $@ - ln -s $(SRCTREE)/nand_spl/nand_boot.c $@ - -# from drivers/mtd/nand directory -$(obj)/nand_ecc.c: - @rm -f $@ - ln -s $(SRCTREE)/drivers/mtd/nand/nand_ecc.c $@ diff --git a/nand_spl/board/amcc/acadia/config.mk b/nand_spl/board/amcc/acadia/config.mk deleted file mode 100644 index d9ff10d5c2..0000000000 --- a/nand_spl/board/amcc/acadia/config.mk +++ /dev/null @@ -1,31 +0,0 @@ -# -# (C) Copyright 2007 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# -# -# AMCC 405EZ Reference Platform (Acadia) board -# - -# -# CONFIG_SYS_TEXT_BASE for SPL: -# -# On 4xx platforms the SPL is located at 0xfffff000...0xffffffff, -# in the last 4kBytes of memory space in cache. -# We will copy this SPL into internal SRAM in start.S. So we set -# CONFIG_SYS_TEXT_BASE to starting address in internal SRAM here. -# -CONFIG_SYS_TEXT_BASE = 0xf8004000 - -# PAD_TO used to generate a 16kByte binary needed for the combined image -# -> PAD_TO = CONFIG_SYS_TEXT_BASE + 0x4000 -PAD_TO = 0xf8008000 - -ifeq ($(debug),1) -PLATFORM_CPPFLAGS += -DDEBUG -endif - -ifeq ($(dbcr),1) -PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 -endif diff --git a/nand_spl/board/amcc/acadia/u-boot.lds b/nand_spl/board/amcc/acadia/u-boot.lds deleted file mode 100644 index a7dac121d3..0000000000 --- a/nand_spl/board/amcc/acadia/u-boot.lds +++ /dev/null @@ -1,48 +0,0 @@ -/* - * (C) Copyright 2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc:common) -SECTIONS -{ - .resetvec 0xf8004ffc : - { - KEEP(*(.resetvec)) - } = 0xffff - - .text : - { - start.o (.text) - nand_boot.o (.text) - ndfc.o (.text) - - *(.text) - *(.fixup) - } - _etext = .; - - .data : - { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - *(.data*) - *(.sdata*) - __got2_start = .; - *(.got2) - __got2_end = .; - } - - _edata = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.sbss) - *(.bss) - . = ALIGN(4); - } - - __bss_end = . ; -} diff --git a/nand_spl/board/amcc/bamboo/Makefile b/nand_spl/board/amcc/bamboo/Makefile deleted file mode 100644 index f975b725eb..0000000000 --- a/nand_spl/board/amcc/bamboo/Makefile +++ /dev/null @@ -1,70 +0,0 @@ -# -# (C) Copyright 2007 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk - -nandobj := $(OBJTREE)/nand_spl/ - -LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds -LDFLAGS := -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(LDFLAGS) \ - $(LDFLAGS_FINAL) -asflags-y += -DCONFIG_NAND_SPL -ccflags-y += -DCONFIG_NAND_SPL - -SOBJS = start.o init.o resetvec.o -COBJS = nand_boot.o nand_ecc.o ndfc.o sdram.o - -OBJS := $(addprefix $(obj)/,$(SOBJS) $(COBJS)) -__OBJS := $(SOBJS) $(COBJS) -LNDIR := $(nandobj)board/$(BOARDDIR) - -targets += $(__OBJS) - -all: $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin - -$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) --pad-to=$(PAD_TO) -O binary $< $@ - -$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) -O binary $< $@ - -$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds - cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \ - -Map $(nandobj)u-boot-spl.map -o $@ - -$(nandobj)u-boot.lds: $(LDSCRIPT) - $(CPP) $(cpp_flags) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ - -# create symbolic links for common files - -# from cpu directory -$(obj)/ndfc.c: - @rm -f $@ - ln -s $(SRCTREE)/drivers/mtd/nand/ndfc.c $@ - -$(obj)/resetvec.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/resetvec.S $@ - -$(obj)/start.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/start.S $@ - -# from board directory -$(obj)/init.S: - @rm -f $@ - ln -s $(SRCTREE)/board/amcc/bamboo/init.S $@ - -# from nand_spl directory -$(obj)/nand_boot.c: - @rm -f $@ - ln -s $(SRCTREE)/nand_spl/nand_boot.c $@ - -# from drivers/mtd/nand directory -$(obj)/nand_ecc.c: - @rm -f $@ - ln -s $(SRCTREE)/drivers/mtd/nand/nand_ecc.c $@ diff --git a/nand_spl/board/amcc/bamboo/config.mk b/nand_spl/board/amcc/bamboo/config.mk deleted file mode 100644 index 6cc8fa30f3..0000000000 --- a/nand_spl/board/amcc/bamboo/config.mk +++ /dev/null @@ -1,33 +0,0 @@ -# -# (C) Copyright 2007 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# -# -# AMCC 440EP Reference Platform (Bamboo) board -# - -# -# CONFIG_SYS_TEXT_BASE for SPL: -# -# On 440EP(x) platforms the SPL is located at 0xfffff000...0xffffffff, -# in the last 4kBytes of memory space in cache. -# We will copy this SPL into instruction-cache in start.S. So we set -# CONFIG_SYS_TEXT_BASE to starting address in i-cache here. -# -CONFIG_SYS_TEXT_BASE = 0x00800000 - -# PAD_TO used to generate a 16kByte binary needed for the combined image -# -> PAD_TO = CONFIG_SYS_TEXT_BASE + 0x4000 -PAD_TO = 0x00804000 - -PLATFORM_CPPFLAGS += -DCONFIG_440=1 - -ifeq ($(debug),1) -PLATFORM_CPPFLAGS += -DDEBUG -endif - -ifeq ($(dbcr),1) -PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 -endif diff --git a/nand_spl/board/amcc/bamboo/sdram.c b/nand_spl/board/amcc/bamboo/sdram.c deleted file mode 100644 index df0dfc1a0d..0000000000 --- a/nand_spl/board/amcc/bamboo/sdram.c +++ /dev/null @@ -1,76 +0,0 @@ -/* - * (C) Copyright 2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -static void wait_init_complete(void) -{ - u32 val; - - do { - mfsdram(SDRAM0_MCSTS, val); - } while (!(val & 0x80000000)); -} - -/* - * phys_size_t initdram(int board_type) - * - * As the name already indicates, this function is called very early - * from start.S and configures the SDRAM with fixed values. This is needed, - * since the 440EP has no internal SRAM and the 4kB NAND_SPL loader has - * not enough free space to implement the complete I2C SPD DDR autodetection - * routines. Therefore the Bamboo only supports the onboard 64MBytes of SDRAM - * when booting from NAND flash. - * - * Note: - * As found out by Eugene O'Brien , the fixed - * DDR setup has problems (U-Boot crashes randomly upon TFTP), when the DIMM - * modules are still plugged in. So it is recommended to remove the DIMM - * modules while using the NAND booting code with the fixed SDRAM setup! - */ -phys_size_t initdram(int board_type) -{ - /* - * Soft-reset SDRAM controller. - */ - mtsdr(SDR0_SRST, SDR0_SRST_DMC); - mtsdr(SDR0_SRST, 0x00000000); - - /* - * Disable memory controller. - */ - mtsdram(SDRAM0_CFG0, 0x00000000); - - /* - * Setup some default - */ - mtsdram(SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */ - mtsdram(SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */ - mtsdram(SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */ - mtsdram(SDRAM0_WDDCTR, 0x00000000); /* wrcp=0 dcd=0 */ - mtsdram(SDRAM0_CLKTR, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */ - - /* - * Following for CAS Latency = 2.5 @ 133 MHz PLB - */ - mtsdram(SDRAM0_B0CR, 0x00082001); - mtsdram(SDRAM0_TR0, 0x41094012); - mtsdram(SDRAM0_TR1, 0x8080083d); /* SS=T2 SL=STAGE 3 CD=1 CT=0x00*/ - mtsdram(SDRAM0_RTR, 0x04100000); /* Interval 7.8µs @ 133MHz PLB */ - mtsdram(SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM*/ - - /* - * Enable the controller, then wait for DCEN to complete - */ - mtsdram(SDRAM0_CFG0, 0x80000000); /* DCEN=1, PMUD=0*/ - wait_init_complete(); - - return CONFIG_SYS_MBYTES_SDRAM << 20; -} diff --git a/nand_spl/board/amcc/bamboo/u-boot.lds b/nand_spl/board/amcc/bamboo/u-boot.lds deleted file mode 100644 index c432368175..0000000000 --- a/nand_spl/board/amcc/bamboo/u-boot.lds +++ /dev/null @@ -1,50 +0,0 @@ -/* - * (C) Copyright 2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc:common) -SECTIONS -{ - .resetvec 0x00800FFC : - { - KEEP(*(.resetvec)) - } = 0xffff - - .text : - { - start.o (.text) - init.o (.text) - nand_boot.o (.text) - sdram.o (.text) - ndfc.o (.text) - - *(.text) - *(.fixup) - } - _etext = .; - - .data : - { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - *(.data*) - *(.sdata*) - __got2_start = .; - *(.got2) - __got2_end = .; - } - - _edata = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.sbss) - *(.bss) - . = ALIGN(4); - } - - __bss_end = . ; -} diff --git a/nand_spl/board/amcc/canyonlands/Makefile b/nand_spl/board/amcc/canyonlands/Makefile deleted file mode 100644 index 250f083dc1..0000000000 --- a/nand_spl/board/amcc/canyonlands/Makefile +++ /dev/null @@ -1,75 +0,0 @@ -# -# (C) Copyright 2008 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk - -nandobj := $(OBJTREE)/nand_spl/ - -LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds -LDFLAGS := -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(LDFLAGS) \ - $(LDFLAGS_FINAL) -asflags-y += -DCONFIG_NAND_SPL -ccflags-y += -DCONFIG_NAND_SPL - -SOBJS := start.o -SOBJS += init.o -SOBJS += resetvec.o -COBJS := ddr2_fixed.o -COBJS += nand_boot.o -COBJS += nand_ecc.o -COBJS += ndfc.o - -OBJS := $(addprefix $(obj)/,$(SOBJS) $(COBJS)) -__OBJS := $(SOBJS) $(COBJS) -LNDIR := $(nandobj)board/$(BOARDDIR) - -targets += $(__OBJS) - -all: $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin - -$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) --pad-to=$(PAD_TO) -O binary $< $@ - -$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) -O binary $< $@ - -$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds - cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \ - -Map $(nandobj)u-boot-spl.map -o $@ - -$(nandobj)u-boot.lds: $(LDSCRIPT) - $(CPP) $(cpp_flags) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ - -# create symbolic links for common files - -# from cpu directory -$(obj)/ndfc.c: - @rm -f $@ - ln -s $(SRCTREE)/drivers/mtd/nand/ndfc.c $@ - -$(obj)/resetvec.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/resetvec.S $@ - -$(obj)/start.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/start.S $@ - -# from board directory -$(obj)/init.S: - @rm -f $@ - ln -s $(SRCTREE)/board/amcc/canyonlands/init.S $@ - -# from nand_spl directory -$(obj)/nand_boot.c: - @rm -f $@ - ln -s $(SRCTREE)/nand_spl/nand_boot.c $@ - -# from drivers/mtd/nand directory -$(obj)/nand_ecc.c: - @rm -f $@ - ln -s $(SRCTREE)/drivers/mtd/nand/nand_ecc.c $@ diff --git a/nand_spl/board/amcc/canyonlands/config.mk b/nand_spl/board/amcc/canyonlands/config.mk deleted file mode 100644 index 780b7ae375..0000000000 --- a/nand_spl/board/amcc/canyonlands/config.mk +++ /dev/null @@ -1,33 +0,0 @@ -# -# (C) Copyright 2008 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# -# -# AMCC 460EX Reference Platform (Canyonlands) board -# - -# -# CONFIG_SYS_TEXT_BASE for SPL: -# -# On 460EX platforms the SPL is located at 0xfffff000...0xffffffff, -# in the last 4kBytes of memory space in cache. -# We will copy this SPL into internal SRAM in start.S. So we set -# CONFIG_SYS_TEXT_BASE to starting address in internal SRAM here. -# -CONFIG_SYS_TEXT_BASE = 0xE3003000 - -# PAD_TO used to generate a 128kByte binary needed for the combined image -# -> PAD_TO = CONFIG_SYS_TEXT_BASE + 0x20000 -PAD_TO = 0xE3023000 - -PLATFORM_CPPFLAGS += -DCONFIG_440=1 - -ifeq ($(debug),1) -PLATFORM_CPPFLAGS += -DDEBUG -endif - -ifeq ($(dbcr),1) -PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 -endif diff --git a/nand_spl/board/amcc/canyonlands/ddr2_fixed.c b/nand_spl/board/amcc/canyonlands/ddr2_fixed.c deleted file mode 100644 index ce8515d513..0000000000 --- a/nand_spl/board/amcc/canyonlands/ddr2_fixed.c +++ /dev/null @@ -1,130 +0,0 @@ -/* - * (C) Copyright 2008-2009 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -/* - * This code can configure those two Crucial SODIMM's: - * - * Crucial CT6464AC667.4FE - 512MB SO-DIMM (single rank) - * Crucial CT6464AC667.8FB - 512MB SO-DIMM (dual rank) - * - */ - -#define TEST_ADDR 0x10000000 -#define TEST_MAGIC 0x11223344 - -static void wait_init_complete(void) -{ - u32 val; - - do { - mfsdram(SDRAM_MCSTAT, val); - } while (!(val & 0x80000000)); -} - -static void ddr_start(void) -{ - mtsdram(SDRAM_MCOPT2, 0x28000000); - wait_init_complete(); -} - -static void ddr_init_common(void) -{ - /* - * Reset the DDR-SDRAM controller. - */ - mtsdr(SDR0_SRST, SDR0_SRST0_DMC); - mtsdr(SDR0_SRST, 0x00000000); - - /* - * These values are cloned from a running NOR booting - * Canyonlands with SPD-DDR2 detection and calibration - * enabled. This will only work for the same memory - * configuration as used here: - * - */ - mtsdram(SDRAM_MCOPT2, 0x00000000); - mtsdram(SDRAM_MODT0, 0x01000000); - mtsdram(SDRAM_WRDTR, 0x82000823); - mtsdram(SDRAM_CLKTR, 0x40000000); - mtsdram(SDRAM_MB0CF, 0x00000201); - mtsdram(SDRAM_RTR, 0x06180000); - mtsdram(SDRAM_SDTR1, 0x80201000); - mtsdram(SDRAM_SDTR2, 0x42103243); - mtsdram(SDRAM_SDTR3, 0x0A0D0D16); - mtsdram(SDRAM_MMODE, 0x00000632); - mtsdram(SDRAM_MEMODE, 0x00000040); - mtsdram(SDRAM_INITPLR0, 0xB5380000); - mtsdram(SDRAM_INITPLR1, 0x82100400); - mtsdram(SDRAM_INITPLR2, 0x80820000); - mtsdram(SDRAM_INITPLR3, 0x80830000); - mtsdram(SDRAM_INITPLR4, 0x80810040); - mtsdram(SDRAM_INITPLR5, 0x80800532); - mtsdram(SDRAM_INITPLR6, 0x82100400); - mtsdram(SDRAM_INITPLR7, 0x8A080000); - mtsdram(SDRAM_INITPLR8, 0x8A080000); - mtsdram(SDRAM_INITPLR9, 0x8A080000); - mtsdram(SDRAM_INITPLR10, 0x8A080000); - mtsdram(SDRAM_INITPLR11, 0x80000432); - mtsdram(SDRAM_INITPLR12, 0x808103C0); - mtsdram(SDRAM_INITPLR13, 0x80810040); - mtsdram(SDRAM_RDCC, 0x40000000); - mtsdram(SDRAM_RQDC, 0x80000038); - mtsdram(SDRAM_RFDC, 0x00000257); - - mtdcr(SDRAM_R0BAS, 0x0000F800); /* MQ0_B0BAS */ -} - -phys_size_t initdram(int board_type) -{ - /* - * First try init for this module: - * - * Crucial CT6464AC667.8FB - 512MB SO-DIMM (dual rank) - */ - - ddr_init_common(); - - /* - * Crucial CT6464AC667.8FB - 512MB SO-DIMM - */ - mtdcr(SDRAM_R0BAS, 0x0000F800); - mtdcr(SDRAM_R1BAS, 0x0400F800); - mtsdram(SDRAM_MCOPT1, 0x05122000); - mtsdram(SDRAM_CODT, 0x02800021); - mtsdram(SDRAM_MB1CF, 0x00000201); - - ddr_start(); - - /* - * Now test if the dual-ranked module is really installed - * by checking an address in the upper 256MByte region - */ - out_be32((void *)TEST_ADDR, TEST_MAGIC); - if (in_be32((void *)TEST_ADDR) != TEST_MAGIC) { - /* - * The test failed, so we assume that the single - * ranked module is installed: - * - * Crucial CT6464AC667.4FE - 512MB SO-DIMM (single rank) - */ - - ddr_init_common(); - - mtdcr(SDRAM_R0BAS, 0x0000F000); - mtsdram(SDRAM_MCOPT1, 0x05322000); - mtsdram(SDRAM_CODT, 0x00800021); - - ddr_start(); - } - - return CONFIG_SYS_MBYTES_SDRAM << 20; -} diff --git a/nand_spl/board/amcc/canyonlands/u-boot.lds b/nand_spl/board/amcc/canyonlands/u-boot.lds deleted file mode 100644 index 6383b1a38f..0000000000 --- a/nand_spl/board/amcc/canyonlands/u-boot.lds +++ /dev/null @@ -1,50 +0,0 @@ -/* - * (C) Copyright 2008 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc:common) -SECTIONS -{ - .resetvec 0xE3003FFC : - { - KEEP(*(.resetvec)) - } = 0xffff - - .text : - { - start.o (.text) - init.o (.text) - nand_boot.o (.text) - ddr2_fixed.o (.text) - ndfc.o (.text) - - *(.text) - *(.fixup) - } - _etext = .; - - .data : - { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - *(.data*) - *(.sdata*) - __got2_start = .; - *(.got2) - __got2_end = .; - } - - _edata = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.sbss) - *(.bss) - . = ALIGN(4); - } - - __bss_end = . ; -} diff --git a/nand_spl/board/amcc/kilauea/Makefile b/nand_spl/board/amcc/kilauea/Makefile deleted file mode 100644 index a8d46899aa..0000000000 --- a/nand_spl/board/amcc/kilauea/Makefile +++ /dev/null @@ -1,77 +0,0 @@ -# -# (C) Copyright 2007 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk - -nandobj := $(OBJTREE)/nand_spl/ - -LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds -LDFLAGS := -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(LDFLAGS) \ - $(LDFLAGS_FINAL) -asflags-y += -DCONFIG_NAND_SPL -ccflags-y += -DCONFIG_NAND_SPL - -SOBJS = start.o resetvec.o cache.o -COBJS = 44x_spd_ddr2.o nand_boot.o nand_ecc.o ndfc.o - -OBJS := $(addprefix $(obj)/,$(SOBJS) $(COBJS)) -__OBJS := $(SOBJS) $(COBJS) -LNDIR := $(nandobj)board/$(BOARDDIR) - -targets += $(__OBJS) - -all: $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin - -$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) --pad-to=$(PAD_TO) -O binary $< $@ - -$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) -O binary $< $@ - -$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds - cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \ - -Map $(nandobj)u-boot-spl.map -o $@ - -$(nandobj)u-boot.lds: $(LDSCRIPT) - $(CPP) $(cpp_flags) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ - -# create symbolic links for common files - -# from cpu directory -$(obj)/44x_spd_ddr2.c: $(obj)/ecc.h - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c $@ - -$(obj)/cache.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/cache.S $@ - -$(obj)/ecc.h: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/ecc.h $@ - -$(obj)/ndfc.c: - @rm -f $@ - ln -s $(SRCTREE)/drivers/mtd/nand/ndfc.c $@ - -$(obj)/resetvec.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/resetvec.S $@ - -$(obj)/start.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/start.S $@ - -# from nand_spl directory -$(obj)/nand_boot.c: - @rm -f $@ - ln -s $(SRCTREE)/nand_spl/nand_boot.c $@ - -# from drivers/nand directory -$(obj)/nand_ecc.c: - @rm -f $@ - ln -s $(SRCTREE)/drivers/mtd/nand/nand_ecc.c $@ diff --git a/nand_spl/board/amcc/kilauea/config.mk b/nand_spl/board/amcc/kilauea/config.mk deleted file mode 100644 index b596b1406c..0000000000 --- a/nand_spl/board/amcc/kilauea/config.mk +++ /dev/null @@ -1,32 +0,0 @@ -# -# (C) Copyright 2007 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# -# -# AMCC 405EX Reference Platform (Kilauea) board -# - -# -# CONFIG_SYS_TEXT_BASE for SPL: -# -# On 4xx platforms the SPL is located at 0xfffff000...0xffffffff, -# in the last 4kBytes of memory space in cache. -# We will copy this SPL into SDRAM since we can't access the NAND -# controller at CS0 while running from this location. So we set -# CONFIG_SYS_TEXT_BASE to starting address in SDRAM here. -# -CONFIG_SYS_TEXT_BASE = 0x00800000 - -# PAD_TO used to generate a 16kByte binary needed for the combined image -# -> PAD_TO = CONFIG_SYS_TEXT_BASE + 0x4000 -PAD_TO = 0x00804000 - -ifeq ($(debug),1) -PLATFORM_CPPFLAGS += -DDEBUG -endif - -ifeq ($(dbcr),1) -PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 -endif diff --git a/nand_spl/board/amcc/kilauea/u-boot.lds b/nand_spl/board/amcc/kilauea/u-boot.lds deleted file mode 100644 index d7262e6c53..0000000000 --- a/nand_spl/board/amcc/kilauea/u-boot.lds +++ /dev/null @@ -1,48 +0,0 @@ -/* - * (C) Copyright 2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc:common) -SECTIONS -{ - .resetvec 0x00800FFC : - { - KEEP(*(.resetvec)) - } = 0xffff - - .text : - { - start.o (.text) - nand_boot.o (.text) - ndfc.o (.text) - - *(.text) - *(.fixup) - } - _etext = .; - - .data : - { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - *(.data*) - *(.sdata*) - __got2_start = .; - *(.got2) - __got2_end = .; - } - - _edata = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.sbss) - *(.bss) - . = ALIGN(4); - } - - __bss_end = . ; -} diff --git a/nand_spl/board/amcc/sequoia/Makefile b/nand_spl/board/amcc/sequoia/Makefile deleted file mode 100644 index b0385ae7a1..0000000000 --- a/nand_spl/board/amcc/sequoia/Makefile +++ /dev/null @@ -1,80 +0,0 @@ -# -# (C) Copyright 2006-2007 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk - -nandobj := $(OBJTREE)/nand_spl/ - -LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds -LDFLAGS := -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(LDFLAGS) \ - $(LDFLAGS_FINAL) -asflags-y += -DCONFIG_NAND_SPL -ccflags-y += -DCONFIG_NAND_SPL - -SOBJS = start.o init.o resetvec.o -COBJS = denali_data_eye.o nand_boot.o nand_ecc.o ndfc.o sdram.o - -OBJS := $(addprefix $(obj)/,$(SOBJS) $(COBJS)) -__OBJS := $(SOBJS) $(COBJS) -LNDIR := $(nandobj)board/$(BOARDDIR) - -targets += $(__OBJS) - -all: $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin - -$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) --pad-to=$(PAD_TO) -O binary $< $@ - -$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) -O binary $< $@ - -$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds - cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \ - -Map $(nandobj)u-boot-spl.map -o $@ - -$(nandobj)u-boot.lds: $(LDSCRIPT) - $(CPP) $(cpp_flags) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ - -# create symbolic links for common files - -# from cpu directory -$(obj)/denali_data_eye.c: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/denali_data_eye.c $@ - -$(obj)/ndfc.c: - @rm -f $@ - ln -s $(SRCTREE)/drivers/mtd/nand/ndfc.c $@ - -$(obj)/resetvec.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/resetvec.S $@ - -$(obj)/start.S: - @rm -f $@ - ln -s $(SRCTREE)/arch/powerpc/cpu/ppc4xx/start.S $@ - -# from board directory -$(obj)/init.S: - @rm -f $@ - ln -s $(SRCTREE)/board/amcc/sequoia/init.S $@ - -$(obj)/sdram.c: - @rm -f $@ - @rm -f $(obj)/sdram.h - ln -s $(SRCTREE)/board/amcc/sequoia/sdram.c $@ - ln -s $(SRCTREE)/board/amcc/sequoia/sdram.h $(obj)/sdram.h - -# from nand_spl directory -$(obj)/nand_boot.c: - @rm -f $@ - ln -s $(SRCTREE)/nand_spl/nand_boot.c $@ - -# from drivers/mtd/nand directory -$(obj)/nand_ecc.c: - @rm -f $@ - ln -s $(SRCTREE)/drivers/mtd/nand/nand_ecc.c $@ diff --git a/nand_spl/board/amcc/sequoia/config.mk b/nand_spl/board/amcc/sequoia/config.mk deleted file mode 100644 index ede7964d9f..0000000000 --- a/nand_spl/board/amcc/sequoia/config.mk +++ /dev/null @@ -1,33 +0,0 @@ -# -# (C) Copyright 2006 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# -# -# AMCC 440EPx Reference Platform (Sequoia) board -# - -# -# CONFIG_SYS_TEXT_BASE for SPL: -# -# On 440EP(x) platforms the SPL is located at 0xfffff000...0xffffffff, -# in the last 4kBytes of memory space in cache. -# We will copy this SPL into internal SRAM in start.S. So we set -# CONFIG_SYS_TEXT_BASE to starting address in internal SRAM here. -# -CONFIG_SYS_TEXT_BASE = 0xE0013000 - -# PAD_TO used to generate a 16kByte binary needed for the combined image -# -> PAD_TO = CONFIG_SYS_TEXT_BASE + 0x4000 -PAD_TO = 0xE0017000 - -PLATFORM_CPPFLAGS += -DCONFIG_440=1 - -ifeq ($(debug),1) -PLATFORM_CPPFLAGS += -DDEBUG -endif - -ifeq ($(dbcr),1) -PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 -endif diff --git a/nand_spl/board/amcc/sequoia/u-boot.lds b/nand_spl/board/amcc/sequoia/u-boot.lds deleted file mode 100644 index 45c0162af6..0000000000 --- a/nand_spl/board/amcc/sequoia/u-boot.lds +++ /dev/null @@ -1,50 +0,0 @@ -/* - * (C) Copyright 2006-2010 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc:common) -SECTIONS -{ - .resetvec 0xE0013FFC : - { - KEEP(*(.resetvec)) - } = 0xffff - - .text : - { - start.o (.text) - init.o (.text) - nand_boot.o (.text) - sdram.o (.text) - ndfc.o (.text) - - *(.text) - *(.fixup) - } - _etext = .; - - .data : - { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - *(.data*) - *(.sdata*) - __got2_start = .; - *(.got2) - __got2_end = .; - } - - _edata = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.sbss) - *(.bss) - . = ALIGN(4); - } - - __bss_end = . ; -}