From: Chen-Yu Tsai Date: Wed, 30 Nov 2016 07:30:30 +0000 (+0800) Subject: sunxi: Enable AXP221s in I2C mode with the R40 SoC X-Git-Tag: v2017.05-rc3~55^2~18 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=409677ec1706c1374f9ce5e1833ae425dd0a9602;p=u-boot sunxi: Enable AXP221s in I2C mode with the R40 SoC The R40 SoC uses the AXP221s in I2C mode to supply power. Some regulator's common usages have changed, and also the recommended voltage for existing usages have changed. Update the defaults to match. Signed-off-by: Chen-Yu Tsai Acked-by: Maxime Ripard --- diff --git a/arch/arm/mach-sunxi/pmic_bus.c b/arch/arm/mach-sunxi/pmic_bus.c index 7c57f02792..f917c3e070 100644 --- a/arch/arm/mach-sunxi/pmic_bus.c +++ b/arch/arm/mach-sunxi/pmic_bus.c @@ -41,6 +41,9 @@ int pmic_bus_init(void) p2wi_init(); ret = p2wi_change_to_p2wi_mode(AXP221_CHIP_ADDR, AXP221_CTRL_ADDR, AXP221_INIT_DATA); +# elif defined CONFIG_MACH_SUN8I_R40 + /* Nothing. R40 uses the AXP221s in I2C mode */ + ret = 0; # else ret = rsb_init(); if (ret) @@ -65,6 +68,8 @@ int pmic_bus_read(u8 reg, u8 *data) #elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER # ifdef CONFIG_MACH_SUN6I return p2wi_read(reg, data); +# elif defined CONFIG_MACH_SUN8I_R40 + return i2c_read(AXP209_I2C_ADDR, reg, 1, data, 1); # else return rsb_read(AXP223_RUNTIME_ADDR, reg, data); # endif @@ -80,6 +85,8 @@ int pmic_bus_write(u8 reg, u8 data) #elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER # ifdef CONFIG_MACH_SUN6I return p2wi_write(reg, data); +# elif defined CONFIG_MACH_SUN8I_R40 + return i2c_write(AXP209_I2C_ADDR, reg, 1, &data, 1); # else return rsb_write(AXP223_RUNTIME_ADDR, reg, data); # endif diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig index 3df7077313..f40b8ff57d 100644 --- a/board/sunxi/Kconfig +++ b/board/sunxi/Kconfig @@ -473,7 +473,7 @@ config USB3_VBUS_PIN config I2C0_ENABLE bool "Enable I2C/TWI controller 0" - default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I + default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_R40 default n if MACH_SUN6I || MACH_SUN8I select CMD_I2C ---help--- diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index 64e5bc2f74..911ecb1144 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -10,7 +10,7 @@ choice prompt "Select Sunxi PMIC Variant" depends on ARCH_SUNXI default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I - default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 + default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 default AXP818_POWER if MACH_SUN8I_A83T default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I @@ -37,7 +37,7 @@ config AXP209_POWER config AXP221_POWER bool "axp221 / axp223 pmic support" - depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 + depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 select CMD_POWEROFF ---help--- Select this to enable support for the axp221/axp223 pmic found on most @@ -70,7 +70,7 @@ endchoice config AXP_DCDC1_VOLT int "axp pmic dcdc1 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER - default 3300 if AXP818_POWER + default 3300 if AXP818_POWER || MACH_SUN8I_R40 default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I ---help--- Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to @@ -97,6 +97,7 @@ config AXP_DCDC2_VOLT On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V. On A80 boards dcdc2 powers the GPU and can be left off. On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V. + On R40 boards dcdc2 is VDD-CPU and should be 1.1V config AXP_DCDC3_VOLT int "axp pmic dcdc3 voltage" @@ -104,6 +105,7 @@ config AXP_DCDC3_VOLT default 900 if AXP809_POWER || AXP818_POWER default 1500 if AXP152_POWER default 1250 if AXP209_POWER + default 1100 if MACH_SUN8I_R40 default 1200 if MACH_SUN6I || MACH_SUN8I ---help--- Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to @@ -114,6 +116,7 @@ config AXP_DCDC3_VOLT On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V. On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V. On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V. + On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V. config AXP_DCDC4_VOLT int "axp pmic dcdc4 voltage" @@ -138,13 +141,13 @@ config AXP_DCDC5_VOLT ---help--- Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to disable dcdc5. - On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and + On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and should be 1.5V, 1.35V if DDR3L is used. config AXP_ALDO1_VOLT int "axp pmic (a)ldo1 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER - default 0 if MACH_SUN6I + default 0 if MACH_SUN6I || MACH_SUN8I_R40 default 1800 if MACH_SUN8I_A83T default 3000 if MACH_SUN8I || MACH_SUN9I ---help--- @@ -183,7 +186,8 @@ config AXP_ALDO3_VOLT Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to disable aldo3. On A10(s) / A13 / A20 boards aldo3 should be 2.8V. - On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V. + On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should + be 3.0V. On A80 boards aldo3 is normally not used. On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be 3.0V.