From: zwelch Date: Tue, 9 Jun 2009 00:58:23 +0000 (+0000) Subject: David Brownell : X-Git-Tag: v0.2.0~378 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=594abeb82bdcbd4bd079ec1a80c092076c55ccae;p=openocd David Brownell : Add configuration for an old AT91rm9200 board, the Cogent CSB 337. Worth noting from the OpenOCD perspective: - It got a real hardware trace port connector; wired up here as much as we can, lacking inexpensive trace-aware dongles. - This is the first in-tree use of the "arm920t cp15" command. It adjusts the CPU clocking and enables i-cache, which gives more than 4x speedup after booting Linux; it's visible even just running U-Boot. git-svn-id: svn://svn.berlios.de/openocd/trunk@2134 b42882b7-edfa-0310-969c-e2dbd0fdcd60 --- diff --git a/tcl/board/csb337.cfg b/tcl/board/csb337.cfg new file mode 100644 index 00000000..1157cb82 --- /dev/null +++ b/tcl/board/csb337.cfg @@ -0,0 +1,118 @@ +# Cogent CSB337 +# http://cogcomp.com/csb_csb337.htm + +source [find target/at91rm9200.cfg] + +# boots from NOR on CS0: 8 MBytes CFI flash, 16-bit bus +flash bank cfi 0x10000000 0x00800000 2 2 $_TARGETNAME + +# ETM9 trace port connector present on this board, 16 data pins. +if { [info exists ETM_DRIVER] } { + etm config $_TARGETNAME 16 normal half $ETM_DRIVER + # OpenOCD may someday support a real trace port driver... + # system config file would need to configure it. +} else { + etm config $_TARGETNAME 16 normal half dummy + etm_dummy config $_TARGETNAME +} + +proc csb337_clk_init { } { + # CPU is in Slow Clock Mode (32KiHz) ... needs slow JTAG clock + jtag_khz 8 + + # CKGR_MOR: start main oscillator (3.6864 MHz) + mww 0xfffffc20 0xff01 + sleep 10 + + # CKGR_PLLAR: start PLL A for CPU and peripherals (184.32 MHz) + mww 0xfffffc28 0x20313e01 + # CKGR_PLLBR: start PLL B for USB timing (96 MHz, with div2) + mww 0xfffffc2c 0x12703e18 + # let PLLs lock + sleep 10 + + # PMC_MCKR: switch to CPU clock = PLLA, master clock = CPU/4 + mww 0xfffffc30 0x0302 + sleep 20 + + # CPU is in Normal Mode ... allows faster JTAG clock speed + jtag_khz 40000 +} + +proc csb337_nor_init { } { + # SMC_CSR0: adjust timings (10 wait states) + mww 0xffffff70 0x1100318a + + flash probe 0 +} + +proc csb337_sdram_init { } { + # enable PIOC clock + mww 0xfffffc10 0x0010 + # PC31..PC16 are D31..D16, with internal pullups like D15..D0 + mww 0xfffff870 0xffff0000 + mww 0xfffff874 0x0 + mww 0xfffff804 0xffff0000 + + # SDRC_CR: set timings + mww 0xffffff98 0x2188b0d5 + + # SDRC_MR: issue all banks precharge to SDRAM + mww 0xffffff90 2 + mww 0x20000000 0 + + # SDRC_MR: 8 autorefresh cycles + mww 0xffffff90 4 + mww 0x20000000 0 + mww 0x20000000 0 + mww 0x20000000 0 + mww 0x20000000 0 + mww 0x20000000 0 + mww 0x20000000 0 + mww 0x20000000 0 + mww 0x20000000 0 + + # SDRC_MR: set SDRAM mode registers (CAS, burst len, etc) + mww 0xffffff90 3 + mww 0x20000080 0 + + # SDRC_TR: set refresh rate + mww 0xffffff94 0x200 + mww 0x20000000 0 + + # SDRC_MR: normal mode, 32 bit bus + mww 0xffffff90 0 + mww 0x20000000 0 +} + +# The rm9200 chip has just been reset. Bring it up far enough +# that we can write flash or run code from SDRAM. +proc csb337_reset_init { } { + csb337_clk_init + + # EBI_CSA: CS0 = NOR, CS1 = SDRAM + mww 0xffffff60 0x02 + + csb337_nor_init + csb337_sdram_init + + # Update CP15 control register ... we don't seem to be able to + # read/modify/write its value through a TCL variable, so just + # write it. Fields are zero unless listed here ... and note + # that OpenOCD numbers this register "2", not "1" (!). + # + # - Core to use Async Clocking mode (so it uses 184 MHz most + # of the time instead of limiting to the master clock rate): + # iA(31) = 1, nF(30) = 1 + # - Icache on (it's disabled now, slowing i-fetches) + # I(12) = 1 + # - Reserved/ones + # 6:3 = 1 + # - Alignment traps enabled + # A(1) = 1 + arm920t cp15 2 0xc000107a +} + +$_TARGETNAME configure -event reset-init {csb337_reset_init} + +# vim:syntax tcl diff --git a/tcl/target/str912.cfg b/tcl/target/str912.cfg index 705326b5..776a8e6d 100644 --- a/tcl/target/str912.cfg +++ b/tcl/target/str912.cfg @@ -1,4 +1,6 @@ # script for str9 +# For more information about the configuration files, take a look at: +# openocd.texi if { [info exists CHIPNAME] } { set _CHIPNAME $CHIPNAME @@ -19,52 +21,74 @@ jtag_nsrst_delay 100 jtag_ntrst_delay 100 #use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst +#reset_config trst_and_srst if { [info exists FLASHTAPID ] } { set _FLASHTAPID $FLASHTAPID } else { set _FLASHTAPID 0x04570041 } -jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID +jtag newtap $_CHIPNAME flash \ + -irlen 8 -ircapture 0x1 -irmask 0x1 \ + -expected-id $_FLASHTAPID if { [info exists CPUTAPID ] } { set _CPUTAPID $CPUTAPID } else { set _CPUTAPID 0x25966041 } -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID +jtag newtap $_CHIPNAME cpu \ + -irlen 4 -ircapture 0x1 -irmask 0xf \ + -expected-id $_CPUTAPID if { [info exists BSTAPID ] } { - set _BSTAPID $BSTAPID + set _BSTAPID1 $BSTAPID + set _BSTAPID2 $BSTAPID } else { - set _BSTAPID 0x1457f041 + set _BSTAPID1 0x1457f041 + set _BSTAPID2 0x2457f041 } -jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID +jtag newtap $_CHIPNAME bs \ + -irlen 5 -ircapture 0x1 -irmask 0x1 \ + -expected-id $_BSTAPID1 -expected-id $_BSTAPID2 set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e +target create $_TARGETNAME arm966e \ + -endian $_ENDIAN \ + -chain-position $_TARGETNAME \ + -variant arm966e $_TARGETNAME configure -event reset-start { jtag_rclk 16 } -$_TARGETNAME configure -event reset-init { - # We can increase speed now that we know the target is halted. - #jtag_rclk 3000 - - # -- Enable 96K RAM - # PFQBC enabled / DTCM & AHB wait-states disabled - mww 0x5C002034 0x0191 +proc str9x_config { } { + # -- Enable 96K RAM w/: + # PFQBC enabled / DTCM & AHB wait-states disabled + mww 0x5C002034 0x0191 + # PFQBC disabled / DTCM & AHB wait-states enabled + #mww 0x5C002034 0x0196 + + # 256K/32k + str9x flash_config 0 3 2 0 0x40000 + # 512K/32K + #str9x flash_config 0 4 2 0 0x80000 +} - str9x flash_config 0 4 2 0 0x80000 - flash protect 0 0 7 off +proc str9x_init { } { + # enable RTCK + jtag_rclk 0 + str9x_config } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0 +$_TARGETNAME configure -event reset-init str9x_init + +$_TARGETNAME configure \ + -work-area-virt 0 \ + -work-area-phys 0x50000000 \ + -work-area-size 16384 \ + -work-area-backup 0 #flash bank str9x 0 0 -flash bank str9x 0x00000000 0x00080000 0 0 0 -flash bank str9x 0x00080000 0x00008000 0 0 0 +flash bank str9x 0x00000000 0x00040000 0 0 0 +flash bank str9x 0x00040000 0x00008000 0 0 0 -# For more information about the configuration files, take a look at: -# openocd.texi