From: Chris Zankel Date: Wed, 10 Aug 2016 15:36:48 +0000 (+0300) Subject: xtensa: add support for the 'xtfpga' evaluation board X-Git-Tag: v2016.09-rc2~40 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=7e270ec3af02d2358f9a454ba0d0bb39f07d14b6;p=u-boot xtensa: add support for the 'xtfpga' evaluation board The 'xtfpga' board is actually a set of FPGA evaluation boards that can be configured to run an Xtensa processor. - Avnet Xilinx LX60 - Avnet Xilinx LX110 - Avnet Xilinx LX200 - Xilinx ML605 - Xilinx KC705 These boards share the same components (open-ethernet, ns16550 serial, lcd display, flash, etc.). Signed-off-by: Chris Zankel Signed-off-by: Max Filippov Reviewed-by: Simon Glass Reviewed-by: Tom Rini --- diff --git a/arch/xtensa/Kconfig b/arch/xtensa/Kconfig index bb6a678f87..2ba7132c20 100644 --- a/arch/xtensa/Kconfig +++ b/arch/xtensa/Kconfig @@ -11,8 +11,11 @@ config SYS_CPU choice prompt "Target select" +config TARGET_XTFPGA + bool "Support XTFPGA" endchoice +source "board/cadence/xtfpga/Kconfig" endmenu diff --git a/arch/xtensa/dts/Makefile b/arch/xtensa/dts/Makefile index eacf6f313b..e14cdac0fc 100644 --- a/arch/xtensa/dts/Makefile +++ b/arch/xtensa/dts/Makefile @@ -2,6 +2,8 @@ # SPDX-License-Identifier: GPL-2.0+ # +dtb-$(CONFIG_XTFPGA) += ml605.dtb ml605_nommu.dtb kc705.dtb kc705_nommu.dtb + targets += $(dtb-y) DTC_FLAGS += diff --git a/arch/xtensa/dts/kc705.dts b/arch/xtensa/dts/kc705.dts new file mode 100644 index 0000000000..3b89e83b30 --- /dev/null +++ b/arch/xtensa/dts/kc705.dts @@ -0,0 +1,15 @@ +/dts-v1/; +/include/ "xtfpga.dtsi" +/include/ "xtfpga-flash-128m.dtsi" + +/ { + compatible = "cdns,xtensa-kc705"; + chosen { + bootargs = "earlycon=uart8250,mmio32native,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug"; + stdout-path = &serial0; + }; + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x38000000>; + }; +}; diff --git a/arch/xtensa/dts/kc705_nommu.dts b/arch/xtensa/dts/kc705_nommu.dts new file mode 100644 index 0000000000..57f0dab87c --- /dev/null +++ b/arch/xtensa/dts/kc705_nommu.dts @@ -0,0 +1,17 @@ +/dts-v1/; +/include/ "xtfpga.dtsi" +/include/ "xtfpga-flash-128m.dtsi" + +/ { + compatible = "cdns,xtensa-kc705"; + chosen { + bootargs = "earlycon=uart8250,mmio32native,0x9d050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug"; + }; + memory@0 { + device_type = "memory"; + reg = <0x60000000 0x10000000>; + }; + soc { + ranges = <0x00000000 0x90000000 0x10000000>; + }; +}; diff --git a/arch/xtensa/dts/ml605.dts b/arch/xtensa/dts/ml605.dts new file mode 100644 index 0000000000..f323f96f98 --- /dev/null +++ b/arch/xtensa/dts/ml605.dts @@ -0,0 +1,15 @@ +/dts-v1/; +/include/ "xtfpga.dtsi" +/include/ "xtfpga-flash-16m.dtsi" + +/ { + compatible = "cdns,xtensa-ml605"; + chosen { + bootargs = "earlycon=uart8250,mmio32native,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug"; + stdout-path = &serial0; + }; + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x18000000>; + }; +}; diff --git a/arch/xtensa/dts/ml605_nommu.dts b/arch/xtensa/dts/ml605_nommu.dts new file mode 100644 index 0000000000..6bdf40055b --- /dev/null +++ b/arch/xtensa/dts/ml605_nommu.dts @@ -0,0 +1,18 @@ +/dts-v1/; +/include/ "xtfpga.dtsi" +/include/ "xtfpga-flash-16m.dtsi" + +/ { + compatible = "cdns,xtensa-ml605"; + chosen { + bootargs = "earlycon=uart8250,mmio32native,0x9d050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug"; + stdout-path = &serial0; + }; + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + soc { + ranges = <0x00000000 0x90000000 0x10000000>; + }; +}; diff --git a/arch/xtensa/dts/xtfpga-flash-128m.dtsi b/arch/xtensa/dts/xtfpga-flash-128m.dtsi new file mode 100644 index 0000000000..d3a88e0298 --- /dev/null +++ b/arch/xtensa/dts/xtfpga-flash-128m.dtsi @@ -0,0 +1,28 @@ +/ { + soc { + flash: flash@00000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x00000000 0x08000000>; + bank-width = <2>; + device-width = <2>; + partition@0x0 { + label = "data"; + reg = <0x00000000 0x06000000>; + }; + partition@0x6000000 { + label = "boot loader area"; + reg = <0x06000000 0x00800000>; + }; + partition@0x6800000 { + label = "kernel image"; + reg = <0x06800000 0x017e0000>; + }; + partition@0x7fe0000 { + label = "boot environment"; + reg = <0x07fe0000 0x00020000>; + }; + }; + }; +}; diff --git a/arch/xtensa/dts/xtfpga-flash-16m.dtsi b/arch/xtensa/dts/xtfpga-flash-16m.dtsi new file mode 100644 index 0000000000..1d97203c18 --- /dev/null +++ b/arch/xtensa/dts/xtfpga-flash-16m.dtsi @@ -0,0 +1,28 @@ +/ { + soc { + flash: flash@08000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x08000000 0x01000000>; + bank-width = <2>; + device-width = <2>; + partition@0x0 { + label = "boot loader area"; + reg = <0x00000000 0x00400000>; + }; + partition@0x400000 { + label = "kernel image"; + reg = <0x00400000 0x00600000>; + }; + partition@0xa00000 { + label = "data"; + reg = <0x00a00000 0x005e0000>; + }; + partition@0xfe0000 { + label = "boot environment"; + reg = <0x00fe0000 0x00020000>; + }; + }; + }; +}; diff --git a/arch/xtensa/dts/xtfpga.dtsi b/arch/xtensa/dts/xtfpga.dtsi new file mode 100644 index 0000000000..cd45f9c2c4 --- /dev/null +++ b/arch/xtensa/dts/xtfpga.dtsi @@ -0,0 +1,137 @@ +/ { + compatible = "cdns,xtensa-xtfpga"; + #address-cells = <1>; + #size-cells = <1>; + interrupt-parent = <&pic>; + + chosen { + bootargs = "earlycon=uart8250,mmio32native,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x06000000>; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + compatible = "cdns,xtensa-cpu"; + reg = <0>; + /* Filled in by platform_setup from FPGA register + * clock-frequency = <100000000>; + */ + }; + }; + + pic: pic { + compatible = "cdns,xtensa-pic"; + /* one cell: internal irq number, + * two cells: second cell == 0: internal irq number + * second cell == 1: external irq number + */ + #interrupt-cells = <2>; + interrupt-controller; + }; + + clocks { + osc: main-oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + clk54: clk54 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <54000000>; + }; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x00000000 0xf0000000 0x10000000>; + + serial0: serial@0d050020 { + device_type = "serial"; + compatible = "ns16550a"; + no-loopback-test; + reg = <0x0d050020 0x20>; + reg-shift = <2>; + reg-io-width = <4>; + native-endian; + interrupts = <0 1>; /* external irq 0 */ + clocks = <&osc>; + }; + + enet0: ethoc@0d030000 { + compatible = "opencores,ethoc"; + reg = <0x0d030000 0x4000 0x0d800000 0x4000>; + native-endian; + interrupts = <1 1>; /* external irq 1 */ + local-mac-address = [00 50 c2 13 6f 00]; + clocks = <&osc>; + }; + + i2s0: xtfpga-i2s@0d080000 { + #sound-dai-cells = <0>; + compatible = "cdns,xtfpga-i2s"; + reg = <0x0d080000 0x40>; + interrupts = <2 1>; /* external irq 2 */ + clocks = <&cdce706 4>; + }; + + i2c0: i2c-master@0d090000 { + compatible = "opencores,i2c-ocores"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0d090000 0x20>; + reg-shift = <2>; + reg-io-width = <4>; + native-endian; + interrupts = <4 1>; + clocks = <&osc>; + + cdce706: clock-synth@69 { + compatible = "ti,cdce706"; + #clock-cells = <1>; + reg = <0x69>; + clocks = <&clk54>; + clock-names = "clk_in0"; + }; + }; + + spi0: spi-master@0d0a0000 { + compatible = "cdns,xtfpga-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0d0a0000 0xc>; + + tlv320aic23: sound-codec@0 { + #sound-dai-cells = <0>; + compatible = "tlv320aic23"; + reg = <0>; + spi-max-frequency = <12500000>; + }; + }; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,format = "i2s"; + simple-audio-card,mclk-fs = <256>; + + simple-audio-card,cpu { + sound-dai = <&i2s0>; + }; + + simple-audio-card,codec { + sound-dai = <&tlv320aic23>; + simple-audio-card,bitclock-master = <0>; + simple-audio-card,frame-master = <0>; + clocks = <&cdce706 4>; + }; + }; +}; diff --git a/board/cadence/xtfpga/Kconfig b/board/cadence/xtfpga/Kconfig new file mode 100644 index 0000000000..69296be49c --- /dev/null +++ b/board/cadence/xtfpga/Kconfig @@ -0,0 +1,39 @@ +if TARGET_XTFPGA + +choice + prompt "XTFPGA board type select" + +config XTFPGA_LX60 + bool "Support Avnet LX60" +config XTFPGA_LX110 + bool "Support Avnet LX110" +config XTFPGA_LX200 + bool "Support Avnet LX200" +config XTFPGA_ML605 + bool "Support Xilinx ML605" +config XTFPGA_KC705 + bool "Support Xilinx KC705" + +endchoice + +config SYS_BOARD + string + default "xtfpga" + +config SYS_VENDOR + string + default "cadence" + +config SYS_CONFIG_NAME + string + default "xtfpga" + +config BOARD_SDRAM_SIZE + hex + default 0x04000000 if XTFPGA_LX60 + default 0x03000000 if XTFPGA_LX110 + default 0x06000000 if XTFPGA_LX200 + default 0x18000000 if XTFPGA_ML605 + default 0x38000000 if XTFPGA_KC705 + +endif diff --git a/board/cadence/xtfpga/MAINTAINERS b/board/cadence/xtfpga/MAINTAINERS new file mode 100644 index 0000000000..f4a2b942d9 --- /dev/null +++ b/board/cadence/xtfpga/MAINTAINERS @@ -0,0 +1,7 @@ +XTFPGA BOARD +M: Max Filippov +S: Maintained +F: board/cadence/xtfpga/ +F: include/configs/xtfpga.h +F: configs/xtfpga_defconfig +F: drivers/sysreset/sysreset_xtfpga.c diff --git a/board/cadence/xtfpga/Makefile b/board/cadence/xtfpga/Makefile new file mode 100644 index 0000000000..fd8f720d68 --- /dev/null +++ b/board/cadence/xtfpga/Makefile @@ -0,0 +1,7 @@ +# +# (C) Copyright 2007 - 2013, Tensilica Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += ${BOARD}.o diff --git a/board/cadence/xtfpga/README b/board/cadence/xtfpga/README new file mode 100644 index 0000000000..5f29e2592f --- /dev/null +++ b/board/cadence/xtfpga/README @@ -0,0 +1,125 @@ + Tensilica 'xtfpga' Evaluation Boards + ==================================== + +Tensilica's 'xtfpga' evaluation boards are actually a set of different +boards that share configurations. The following is a list of supported +hardware by this board type: + +- XT-AV60 / LX60 +- XT-AV110 / LX110 +- XT-AV200 / LX200 +- ML605 +- KC705 + +All boards provide the following common configurations: + +- An Xtensa or Diamond processor core. +- An on-chip-debug (OCD) JTAG interface. +- A 16550 compatible UART and serial port. +- An OpenCores Wishbone 10/100-base-T ethernet interface. +- A 32 char two line LCD display. (except for the LX200) + +LX60/LX110/LX200: + +- Virtex-4 (XC4VLX60 / XCV4LX200) / Virtext-5 (XC5VLX110) +- 128MB / 64MB (LX60) memory +- 16MB / 4MB (LX60) Linear Flash + +ML605 + +- Virtex-6 (XC6VLX240T) +- 512MB DDR3 memory +- 16MB Linear BPI Flash + +KC705 (Xilinx) + +- Kintex-7 XC7K325T FPGA +- 1GB DDR3 memory +- 128MB Linear BPI Flash + + +Setting up the Board +-------------------- + +The serial port defaults to 115200 baud, no parity and 1 stop bit. +A terminal emulator must be set accordingly to see the U-Boot prompt. + + +Board Configurations LX60/LX110/LX200/ML605/KC705 +------------------------------------------------- + +The LX60/LX110/LX200/ML605 contain an 8-way DIP switch that controls +the boot mapping and selects from a range of default ethernet MAC +addresses. + +Boot Mapping (DIP switch 8): + + DIP switch 8 maps the system ROM address space (in which the + reset vector resides) to either SRAM (off, 0, down) or Flash + (on, 1, up). This mapping is implemented in the FPGA bitstream + and cannot be disabled by software, therefore DIP switch 8 is no + available for application use. Note DIP switch 7 is reserved by + Tensilica for future possible hardware use. + + Mapping to SRAM allows U-Boot to be debugged with an OCD/JTAG + tool such as the Xtensa OCD Daemon connected via a suppored probe. + See the tools documentation for supported probes and how to + connect them. Be aware that the board has only 128 KB of SRAM, + therefore U-Boot must fit within this space to debug an image + intended for the Flash. This issues is discussed in a separate + section toward the end. + + Mapping to flash allows U-Boot to start on reset, provided it + has been programmed into the first two 64 KB sectors of the Flash. + + The Flash is always mapped at a device (memory mapped I/O) address + (the address is board specific and is expressed as CFG_FLASH_BASE). + The device address is used by U-Boot to program the flash, and may + be used to specify an application to run or U-Boot image to boot. + +Default MAC Address (DIP switches 1-6): + + When the board is first powered on, or after the environment has + been reinitialized, the ethernet MAC address receives a default + value whose least significant 6 bits come from DIP switches 1-6. + The default is 00:50:C2:13:6F:xx where xx ranges from 0..3F + according to the DIP switches, where "on"==1 and "off"==0, and + switch 1 is the least-significant bit. + + After initial startup, the MAC address is stored in the U-Boot + environment variable 'ethaddr'. The user may change this to any + other address with the "setenv" comamnd. After the environment + has been saved to Flash by the "saveenv" command, this will be + used and the DIP switches no longer consulted. DIP swithes 1-6 + may then be used for application purposes. + +The KC705 board contains 4-way DIP switch, way 1 is the boot mapping +switch and ways 2-4 control the low three bits of the MAC address. + + +Limitation of SDRAM Size for OCD Debugging on the LX60 +------------------------------------------------------ + +The XT-AV60 board has only 128 KB of SDRAM that can be mapped +to the system ROM address space for debugging a ROM image under +OCD/JTAG. This limits the useful size of U-Boot to 128 KB (0x20000) +or the first 2 sectors of the flash. + +This can pose a problem if all the sources are compiled with -O0 +for debugging. The code size is then too large, in which case it +would be necessary to temporarily alter the linker script to place +the load addresses (LMA) in the RAM (VMA) so that OCD loads U-Boot +directly there and does not unpack. In practice this is not really +necessary as long as only a limited set of sources need to be +debugged, because the image can still fit into the 128 KB SRAM. + +The recommended procedure for debugging is to first build U-Boot +with the default optimization level (-Os), and then touch and +rebuild incrementally with -O0 so that only the touched sources +are recompiled with -O0. To build with -O0, pass it in the KCFLAGS +variable to make. + +Because this problem is easy to fall into and difficult to debug +if one doesn't expect it, the linker script provides a link-time +check and fatal error message if the image size exceeds 128 KB. + diff --git a/board/cadence/xtfpga/xtfpga.c b/board/cadence/xtfpga/xtfpga.c new file mode 100644 index 0000000000..5899aa6362 --- /dev/null +++ b/board/cadence/xtfpga/xtfpga.c @@ -0,0 +1,115 @@ +/* + * (C) Copyright 2007 - 2013 Tensilica Inc. + * (C) Copyright 2014 - 2016 Cadence Design Systems Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Check board idendity. + * (Print information about the board to stdout.) + */ + + +#if defined(CONFIG_XTFPGA_LX60) +const char *board = "XT_AV60"; +const char *description = "Avnet Xilinx LX60 FPGA Evaluation Board / "; +#elif defined(CONFIG_XTFPGA_LX110) +const char *board = "XT_AV110"; +const char *description = "Avnet Xilinx Virtex-5 LX110 Evaluation Kit / "; +#elif defined(CONFIG_XTFPGA_LX200) +const char *board = "XT_AV200"; +const char *description = "Avnet Xilinx Virtex-4 LX200 Evaluation Kit / "; +#elif defined(CONFIG_XTFPGA_ML605) +const char *board = "XT_ML605"; +const char *description = "Xilinx Virtex-6 FPGA ML605 Evaluation Kit / "; +#elif defined(CONFIG_XTFPGA_KC705) +const char *board = "XT_KC705"; +const char *description = "Xilinx Kintex-7 FPGA KC705 Evaluation Kit / "; +#else +const char *board = ""; +const char *description = ""; +#endif + +int checkboard(void) +{ + printf("Board: %s: %sTensilica bitstream\n", board, description); + return 0; +} + +void dram_init_banksize(void) +{ + gd->bd->bi_memstart = PHYSADDR(CONFIG_SYS_SDRAM_BASE); + gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE; +} + +int board_postclk_init(void) +{ + /* + * Obtain CPU clock frequency from board and cache in global + * data structure (Hz). Return 0 on success (OK to continue), + * else non-zero (hang). + */ + +#ifdef CONFIG_SYS_FPGAREG_FREQ + gd->cpu_clk = (*(volatile unsigned long *)CONFIG_SYS_FPGAREG_FREQ); +#else + /* early Tensilica bitstreams lack this reg, but most run at 50 MHz */ + gd->cpu_clk = 50000000UL; +#endif + return 0; +} + +/* + * Miscellaneous late initializations. + * The environment has been set up, so we can set the Ethernet address. + */ + +int misc_init_r(void) +{ +#ifdef CONFIG_CMD_NET + /* + * Initialize ethernet environment variables and board info. + * Default MAC address comes from CONFIG_ETHADDR + DIP switches 1-6. + */ + + char *s = getenv("ethaddr"); + if (s == 0) { + unsigned int x; + char s[] = __stringify(CONFIG_ETHBASE); + x = (*(volatile u32 *)CONFIG_SYS_FPGAREG_DIPSW) + & FPGAREG_MAC_MASK; + sprintf(&s[15], "%02x", x); + setenv("ethaddr", s); + } +#endif /* CONFIG_CMD_NET */ + + return 0; +} + +U_BOOT_DEVICE(sysreset) = { + .name = "xtfpga_sysreset", +}; + +static struct ethoc_eth_pdata ethoc_pdata = { + .eth_pdata = { + .iobase = CONFIG_SYS_ETHOC_BASE, + }, + .packet_base = CONFIG_SYS_ETHOC_BUFFER_ADDR, +}; + +U_BOOT_DEVICE(ethoc) = { + .name = "ethoc", + .platdata = ðoc_pdata, +}; diff --git a/configs/xtfpga_defconfig b/configs/xtfpga_defconfig new file mode 100644 index 0000000000..535850c962 --- /dev/null +++ b/configs/xtfpga_defconfig @@ -0,0 +1,22 @@ +CONFIG_XTENSA=y +CONFIG_SYS_CPU="dc233c" +CONFIG_XTFPGA_KC705=y +CONFIG_BOOTDELAY=10 +CONFIG_SYS_PROMPT="U-Boot> " +CONFIG_AUTOBOOT_KEYED=y +CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press to stop\n" +CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_CMD_ASKENV=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_PING=y +CONFIG_DM=y +# CONFIG_DM_WARN is not set +# CONFIG_DM_DEVICE_REMOVE is not set +# CONFIG_DM_STDIO is not set +# CONFIG_DM_SEQ_ALIAS is not set +CONFIG_SYSRESET=y +CONFIG_DM_ETH=y +CONFIG_PHYLIB=y +CONFIG_ETHOC=y +CONFIG_SYS_NS16550=y +CONFIG_OF_LIBFDT=y diff --git a/drivers/sysreset/Makefile b/drivers/sysreset/Makefile index 7db1b69acc..fa75cc52de 100644 --- a/drivers/sysreset/Makefile +++ b/drivers/sysreset/Makefile @@ -13,3 +13,4 @@ obj-$(CONFIG_ROCKCHIP_RK3288) += sysreset_rk3288.o obj-$(CONFIG_ROCKCHIP_RK3399) += sysreset_rk3399.o obj-$(CONFIG_SANDBOX) += sysreset_sandbox.o obj-$(CONFIG_ARCH_SNAPDRAGON) += sysreset_snapdragon.o +obj-$(CONFIG_TARGET_XTFPGA) += sysreset_xtfpga.o diff --git a/drivers/sysreset/sysreset_xtfpga.c b/drivers/sysreset/sysreset_xtfpga.c new file mode 100644 index 0000000000..54fd5a0163 --- /dev/null +++ b/drivers/sysreset/sysreset_xtfpga.c @@ -0,0 +1,37 @@ +/* + * Cadence Tensilica xtfpga system reset driver. + * + * (C) Copyright 2016 Cadence Design Systems Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include + +static int xtfpga_reset_request(struct udevice *dev, enum sysreset_t type) +{ + switch (type) { + case SYSRESET_COLD: + writel(CONFIG_SYS_FPGAREG_RESET_CODE, + CONFIG_SYS_FPGAREG_RESET); + break; + default: + return -EPROTONOSUPPORT; + } + + return -EINPROGRESS; +} + +static struct sysreset_ops xtfpga_sysreset_ops = { + .request = xtfpga_reset_request, +}; + +U_BOOT_DRIVER(xtfpga_sysreset) = { + .name = "xtfpga_sysreset", + .id = UCLASS_SYSRESET, + .ops = &xtfpga_sysreset_ops, +}; diff --git a/include/configs/xtfpga.h b/include/configs/xtfpga.h new file mode 100644 index 0000000000..c5b06e3e0a --- /dev/null +++ b/include/configs/xtfpga.h @@ -0,0 +1,268 @@ +/* + * Copyright (C) 2007-2013 Tensilica, Inc. + * Copyright (C) 2014 - 2016 Cadence Design Systems Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include +#include +#include + +/* + * The 'xtfpga' board describes a set of very similar boards with only minimal + * differences. + */ + +/*=====================*/ +/* Board and Processor */ +/*=====================*/ + +#define CONFIG_XTFPGA + +/* FPGA CPU freq after init */ +#define CONFIG_SYS_CLK_FREQ (gd->cpu_clk) + +/*===================*/ +/* RAM Layout */ +/*===================*/ + +#if XCHAL_HAVE_PTP_MMU +#define CONFIG_SYS_MEMORY_BASE \ + (XCHAL_VECBASE_RESET_VADDR - XCHAL_VECBASE_RESET_PADDR) +#define CONFIG_SYS_IO_BASE 0xf0000000 +#else +#define CONFIG_SYS_MEMORY_BASE 0x60000000 +#define CONFIG_SYS_IO_BASE 0x90000000 +#define CONFIG_MAX_MEM_MAPPED 0x10000000 +#endif + +/* Onboard RAM sizes: + * + * LX60 0x04000000 64 MB + * LX110 0x03000000 48 MB + * LX200 0x06000000 96 MB + * ML605 0x18000000 384 MB + * KC705 0x38000000 896 MB + * + * noMMU configurations can only see first 256MB of onboard memory. + */ + +#if XCHAL_HAVE_PTP_MMU || CONFIG_BOARD_SDRAM_SIZE < 0x10000000 +#define CONFIG_SYS_SDRAM_SIZE CONFIG_BOARD_SDRAM_SIZE +#else +#define CONFIG_SYS_SDRAM_SIZE 0x10000000 +#endif + +#define CONFIG_SYS_SDRAM_BASE MEMADDR(0x00000000) + +/* Lx60 can only map 128kb memory (instead of 256kb) when running under OCD */ +#ifdef CONFIG_XTFPGA_LX60 +# define CONFIG_SYS_MONITOR_LEN 0x00020000 /* 128KB */ +#else +# define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256KB */ +#endif + +#define CONFIG_SYS_STACKSIZE (512 << 10) /* stack 512KB */ +#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* heap 256KB */ + +/* Linux boot param area in RAM (used only when booting linux) */ +#define CONFIG_SYS_BOOTPARAMS_LEN (64 << 10) + +/* Memory test is destructive so default must not overlap vectors or U-Boot*/ +#define CONFIG_SYS_MEMTEST_START MEMADDR(0x01000000) +#define CONFIG_SYS_MEMTEST_END MEMADDR(0x02000000) + +/* Load address for stand-alone applications. + * MEMADDR cannot be used here, because the definition needs to be + * a plain number as it's used as -Ttext argument for ld in standalone + * example makefile. + * Handle noMMU vs MMUv2 vs MMUv3 distinction here manually. + */ +#if XCHAL_HAVE_PTP_MMU +#if XCHAL_VECBASE_RESET_VADDR == XCHAL_VECBASE_RESET_PADDR +#define CONFIG_STANDALONE_LOAD_ADDR 0x00800000 +#else +#define CONFIG_STANDALONE_LOAD_ADDR 0xd0800000 +#endif +#else +#define CONFIG_STANDALONE_LOAD_ADDR 0x60800000 +#endif + +#if defined(CONFIG_MAX_MEM_MAPPED) && \ + CONFIG_MAX_MEM_MAPPED < CONFIG_SYS_SDRAM_SIZE +#define CONFIG_SYS_MEMORY_SIZE CONFIG_MAX_MEM_MAPPED +#else +#define CONFIG_SYS_MEMORY_SIZE CONFIG_SYS_SDRAM_SIZE +#endif + +#define CONFIG_SYS_MEMORY_TOP MEMADDR(CONFIG_SYS_MEMORY_SIZE) +#define CONFIG_SYS_TEXT_ADDR \ + (CONFIG_SYS_MEMORY_TOP - CONFIG_SYS_MONITOR_LEN) + +/* Used by tftpboot; env var 'loadaddr' */ +#define CONFIG_SYS_LOAD_ADDR MEMADDR(0x02000000) + +/*==============================*/ +/* U-Boot general configuration */ +/*==============================*/ + +#undef CONFIG_USE_IRQ /* Keep it simple, poll only */ +#define CONFIG_BOARD_POSTCLK_INIT +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_MISC_INIT_R + +#define CONFIG_BOOTFILE "uImage" + /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 + /* Prt buf */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) + /* max number of command args */ +#define CONFIG_SYS_MAXARGS 16 + /* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/*=================*/ +/* U-Boot commands */ +/*=================*/ + +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_SAVES + +/*==============================*/ +/* U-Boot autoboot configuration */ +/*==============================*/ + +#define CONFIG_BOOT_RETRY_TIME 60 /* retry after 60 secs */ + +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE /* Support tab autocompletion */ +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC +#define CONFIG_SHOW_BOOT_PROGRESS + +#ifdef DEBUG +#define CONFIG_PANIC_HANG 1 /* Require manual reboot */ +#endif + + +/*=========================================*/ +/* FPGA Registers (board info and control) */ +/*=========================================*/ + +/* + * These assume FPGA bitstreams from Tensilica release RB and up. Earlier + * releases may not provide any/all of these registers or at these offsets. + * Some of the FPGA registers are broken down into bitfields described by + * SHIFT left amount and field WIDTH (bits), and also by a bitMASK. + */ + +/* Date of FPGA bitstream build in binary coded decimal (BCD) */ +#define CONFIG_SYS_FPGAREG_DATE IOADDR(0x0D020000) +#define FPGAREG_MTH_SHIFT 24 /* BCD month 1..12 */ +#define FPGAREG_MTH_WIDTH 8 +#define FPGAREG_MTH_MASK 0xFF000000 +#define FPGAREG_DAY_SHIFT 16 /* BCD day 1..31 */ +#define FPGAREG_DAY_WIDTH 8 +#define FPGAREG_DAY_MASK 0x00FF0000 +#define FPGAREG_YEAR_SHIFT 0 /* BCD year 2001..9999*/ +#define FPGAREG_YEAR_WIDTH 16 +#define FPGAREG_YEAR_MASK 0x0000FFFF + +/* FPGA core clock frequency in Hz (also input to UART) */ +#define CONFIG_SYS_FPGAREG_FREQ IOADDR(0x0D020004) /* CPU clock frequency*/ + +/* + * DIP switch (left=sw1=lsb=bit0, right=sw8=msb=bit7; off=0, on=1): + * Bits 0..5 set the lower 6 bits of the default ethernet MAC. + * Bit 6 is reserved for future use by Tensilica. + * Bit 7 maps the first 128KB of ROM address space at CONFIG_SYS_ROM_BASE to + * the base of flash * (when on/1) or to the base of RAM (when off/0). + */ +#define CONFIG_SYS_FPGAREG_DIPSW IOADDR(0x0D02000C) +#define FPGAREG_MAC_SHIFT 0 /* Ethernet MAC bits 0..5 */ +#define FPGAREG_MAC_WIDTH 6 +#define FPGAREG_MAC_MASK 0x3f +#define FPGAREG_BOOT_SHIFT 7 /* Boot ROM addr mapping */ +#define FPGAREG_BOOT_WIDTH 1 +#define FPGAREG_BOOT_MASK 0x80 +#define FPGAREG_BOOT_RAM 0 +#define FPGAREG_BOOT_FLASH (1<