From: Simon Glass Date: Wed, 17 May 2017 09:25:05 +0000 (-0600) Subject: Drop digital thermometer and thermostat (DTT) drivers X-Git-Tag: v2017.07-rc1~236 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=853eaa4f301c15584f3664f1be000921810d7825;p=u-boot Drop digital thermometer and thermostat (DTT) drivers This subsystem is quite old. It has been replaced with a driver-model version (UCLASS_THERMAL). Boards are free to convert to that if required, but here is a removal patch that could be applied in the meantime. Signed-off-by: Simon Glass Reviewed-by: Heiko Schocher Reviewed-by: Tom Rini --- diff --git a/README b/README index a31065b6f5..b6bce6f558 100644 --- a/README +++ b/README @@ -830,7 +830,6 @@ The following options need to be configured: CONFIG_CMD_CRC32 * crc32 CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics - CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EDITENV edit env variable CONFIG_CMD_EEPROM * EEPROM read/write support @@ -2324,11 +2323,6 @@ The following options need to be configured: If defined, then this indicates the I2C bus number for the RTC. If not defined, then U-Boot assumes that RTC is on I2C bus 0. - CONFIG_SYS_DTT_BUS_NUM - - If defined, then this indicates the I2C bus number for the DTT. - If not defined, then U-Boot assumes that DTT is on I2C bus 0. - CONFIG_SOFT_I2C_READ_REPEATED_START defining this will force the i2c_read() function in diff --git a/board/gdsys/405ep/dlvision-10g.c b/board/gdsys/405ep/dlvision-10g.c index e400d1945a..b531786653 100644 --- a/board/gdsys/405ep/dlvision-10g.c +++ b/board/gdsys/405ep/dlvision-10g.c @@ -10,7 +10,6 @@ #include #include #include -#include #include "405ep.h" #include @@ -61,8 +60,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR; int misc_init_r(void) { - /* startup fans */ - dtt_init(); + /* + * Note: DTT has been removed. Please use UCLASS_THERMAL. + * + * startup fans + * + * dtt_init(); + */ return 0; } diff --git a/board/gdsys/405ep/io.c b/board/gdsys/405ep/io.c index 81b49659ff..1484469bb0 100644 --- a/board/gdsys/405ep/io.c +++ b/board/gdsys/405ep/io.c @@ -11,7 +11,6 @@ #include #include -#include #include #include "405ep.h" @@ -41,8 +40,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR; int misc_init_r(void) { - /* startup fans */ - dtt_init(); + /* + * Note: DTT has been removed. Please use UCLASS_THERMAL. + * + * startup fans + * + * dtt_init(); + */ return 0; } diff --git a/board/gdsys/405ep/neo.c b/board/gdsys/405ep/neo.c index ff0edb2547..ad88af2d46 100644 --- a/board/gdsys/405ep/neo.c +++ b/board/gdsys/405ep/neo.c @@ -10,7 +10,6 @@ #include #include #include -#include #include "405ep.h" #include @@ -32,8 +31,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR; int misc_init_r(void) { - /* startup fans */ - dtt_init(); + /* + * Note: DTT has been removed. Please use UCLASS_THERMAL. + * + * startup fans + * + * dtt_init(); + */ return 0; } diff --git a/board/gdsys/405ex/io64.c b/board/gdsys/405ex/io64.c index 0a7baaa9db..9ef965bbfa 100644 --- a/board/gdsys/405ex/io64.c +++ b/board/gdsys/405ex/io64.c @@ -26,7 +26,6 @@ #include #include -#include DECLARE_GLOBAL_DATA_PTR; @@ -70,8 +69,13 @@ static inline void blank_string(int size) */ int misc_init_r(void) { - /* startup fans */ - dtt_init(); + /* + * Note: DTT has been removed. Please use UCLASS_THERMAL. + * + * startup fans + * + * dtt_init(); + */ #ifdef CONFIG_ENV_IS_IN_FLASH /* Monitor protection ON by default */ diff --git a/cmd/Makefile b/cmd/Makefile index e98786807b..f043407656 100644 --- a/cmd/Makefile +++ b/cmd/Makefile @@ -43,7 +43,6 @@ ifdef CONFIG_POST obj-$(CONFIG_CMD_DIAG) += diag.o endif obj-$(CONFIG_CMD_DISPLAY) += display.o -obj-$(CONFIG_CMD_DTT) += dtt.o obj-$(CONFIG_CMD_ECHO) += echo.o obj-$(CONFIG_ENV_IS_IN_EEPROM) += eeprom.o obj-$(CONFIG_CMD_EEPROM) += eeprom.o diff --git a/cmd/dtt.c b/cmd/dtt.c deleted file mode 100644 index dd427a3d0b..0000000000 --- a/cmd/dtt.c +++ /dev/null @@ -1,120 +0,0 @@ -/* - * (C) Copyright 2001 - * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include - -#include -#include -#include -#include - -#if defined CONFIG_DTT_SENSORS -static unsigned long sensor_initialized; - -static void _initialize_dtt(void) -{ - int i; - unsigned char sensors[] = CONFIG_DTT_SENSORS; - - for (i = 0; i < sizeof(sensors); i++) { - if ((sensor_initialized & (1 << i)) == 0) { - if (dtt_init_one(sensors[i]) != 0) { - printf("DTT%d: Failed init!\n", i); - continue; - } - sensor_initialized |= (1 << i); - } - } -} - -void dtt_init(void) -{ - int old_bus; - - /* switch to correct I2C bus */ - old_bus = I2C_GET_BUS(); - I2C_SET_BUS(CONFIG_SYS_DTT_BUS_NUM); - - _initialize_dtt(); - - /* switch back to original I2C bus */ - I2C_SET_BUS(old_bus); -} -#endif - -int dtt_i2c(void) -{ -#if defined CONFIG_DTT_SENSORS - int i; - unsigned char sensors[] = CONFIG_DTT_SENSORS; - int old_bus; - - /* Force a compilation error, if there are more then 32 sensors */ - BUILD_BUG_ON(sizeof(sensors) > 32); - /* switch to correct I2C bus */ -#ifdef CONFIG_SYS_I2C - old_bus = i2c_get_bus_num(); - i2c_set_bus_num(CONFIG_SYS_DTT_BUS_NUM); -#else - old_bus = I2C_GET_BUS(); - I2C_SET_BUS(CONFIG_SYS_DTT_BUS_NUM); -#endif - - _initialize_dtt(); - - /* - * Loop through sensors, read - * temperature, and output it. - */ - for (i = 0; i < sizeof(sensors); i++) - printf("DTT%d: %i C\n", i + 1, dtt_get_temp(sensors[i])); - - /* switch back to original I2C bus */ -#ifdef CONFIG_SYS_I2C - i2c_set_bus_num(old_bus); -#else - I2C_SET_BUS(old_bus); -#endif -#endif - - return 0; -} - -int dtt_tmu(void) -{ -#if defined CONFIG_TMU_CMD_DTT - int cur_temp; - - /* Sense and return latest thermal info */ - if (tmu_monitor(&cur_temp) == TMU_STATUS_INIT) { - puts("TMU is in unknown state, temperature is invalid\n"); - return -1; - } - printf("Current temperature: %u degrees Celsius\n", cur_temp); -#endif - return 0; -} - -int do_dtt(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) -{ - int err = 0; - - err |= dtt_i2c(); - err |= dtt_tmu(); - - return err; -} /* do_dtt() */ - -/***************************************************/ - -U_BOOT_CMD( - dtt, 1, 1, do_dtt, - "Read temperature from Digital Thermometer and Thermostat", - "" -); diff --git a/drivers/Kconfig b/drivers/Kconfig index a5f24d72da..a736386a0d 100644 --- a/drivers/Kconfig +++ b/drivers/Kconfig @@ -30,8 +30,6 @@ source "drivers/fpga/Kconfig" source "drivers/gpio/Kconfig" -source "drivers/hwmon/Kconfig" - source "drivers/i2c/Kconfig" source "drivers/input/Kconfig" diff --git a/drivers/Makefile b/drivers/Makefile index f16d7fdb4f..058bccb761 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -74,7 +74,6 @@ obj-$(CONFIG_CPU) += cpu/ obj-y += crypto/ obj-y += firmware/ obj-$(CONFIG_FPGA) += fpga/ -obj-y += hwmon/ obj-y += misc/ obj-$(CONFIG_MMC) += mmc/ obj-y += pcmcia/ diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig deleted file mode 100644 index e69de29bb2..0000000000 diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile deleted file mode 100644 index b4fb057c16..0000000000 --- a/drivers/hwmon/Makefile +++ /dev/null @@ -1,22 +0,0 @@ -# -# (C) Copyright 2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# (C) Copyright 2001 -# Erik Theisen, Wave 7 Optics, etheisen@mindspring.com. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -#ccflags-y += -DDEBUG - -obj-$(CONFIG_DTT_ADM1021) += adm1021.o -obj-$(CONFIG_DTT_ADT7460) += adt7460.o -obj-$(CONFIG_DTT_DS1621) += ds1621.o -obj-$(CONFIG_DTT_DS1722) += ds1722.o -obj-$(CONFIG_DTT_DS1775) += ds1775.o -obj-$(CONFIG_DTT_DS620) += ds620.o -obj-$(CONFIG_DTT_LM63) += lm63.o -obj-$(CONFIG_DTT_LM73) += lm73.o -obj-$(CONFIG_DTT_LM75) += lm75.o -obj-$(CONFIG_DTT_LM81) += lm81.o diff --git a/drivers/hwmon/adm1021.c b/drivers/hwmon/adm1021.c deleted file mode 100644 index 99e942b499..0000000000 --- a/drivers/hwmon/adm1021.c +++ /dev/null @@ -1,164 +0,0 @@ -/* - * (C) Copyright 2003 - * Murray Jensen, CSIRO-MIT, Murray.Jensen@csiro.au - * - * based on dtt/lm75.c which is ... - * - * (C) Copyright 2001 - * Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Analog Devices's ADM1021 - * "Low Cost Microprocessor System Temperature Monitor" - */ - -#include - -#include -#include - -#define DTT_READ_LOC_VALUE 0x00 -#define DTT_READ_REM_VALUE 0x01 -#define DTT_READ_STATUS 0x02 -#define DTT_READ_CONFIG 0x03 -#define DTT_READ_CONVRATE 0x04 -#define DTT_READ_LOC_HIGHLIM 0x05 -#define DTT_READ_LOC_LOWLIM 0x06 -#define DTT_READ_REM_HIGHLIM 0x07 -#define DTT_READ_REM_LOWLIM 0x08 -#define DTT_READ_DEVID 0xfe - -#define DTT_WRITE_CONFIG 0x09 -#define DTT_WRITE_CONVRATE 0x0a -#define DTT_WRITE_LOC_HIGHLIM 0x0b -#define DTT_WRITE_LOC_LOWLIM 0x0c -#define DTT_WRITE_REM_HIGHLIM 0x0d -#define DTT_WRITE_REM_LOWLIM 0x0e -#define DTT_WRITE_ONESHOT 0x0f - -#define DTT_STATUS_BUSY 0x80 /* 1=ADC Converting */ -#define DTT_STATUS_LHIGH 0x40 /* 1=Local High Temp Limit Tripped */ -#define DTT_STATUS_LLOW 0x20 /* 1=Local Low Temp Limit Tripped */ -#define DTT_STATUS_RHIGH 0x10 /* 1=Remote High Temp Limit Tripped */ -#define DTT_STATUS_RLOW 0x08 /* 1=Remote Low Temp Limit Tripped */ -#define DTT_STATUS_OPEN 0x04 /* 1=Remote Sensor Open-Circuit */ - -#define DTT_CONFIG_ALERT_MASKED 0x80 /* 0=ALERT Enabled, 1=ALERT Masked */ -#define DTT_CONFIG_STANDBY 0x40 /* 0=Run, 1=Standby */ - -#define DTT_ADM1021_DEVID 0x41 - -typedef - struct { - uint i2c_addr:7; /* 7bit i2c chip address */ - uint conv_rate:3; /* conversion rate */ - uint enable_alert:1; /* enable alert output pin */ - uint enable_local:1; /* enable internal temp sensor */ - uint max_local:8; /* internal temp maximum */ - uint min_local:8; /* internal temp minimum */ - uint enable_remote:1; /* enable remote temp sensor */ - uint max_remote:8; /* remote temp maximum */ - uint min_remote:8; /* remote temp minimum */ - } -dtt_cfg_t; - -dtt_cfg_t dttcfg[] = CONFIG_SYS_DTT_ADM1021; - -int -dtt_read (int sensor, int reg) -{ - dtt_cfg_t *dcp = &dttcfg[sensor >> 1]; - uchar data; - - if (i2c_read(dcp->i2c_addr, reg, 1, &data, 1) != 0) - return -1; - - return (int)data; -} /* dtt_read() */ - -int -dtt_write (int sensor, int reg, int val) -{ - dtt_cfg_t *dcp = &dttcfg[sensor >> 1]; - uchar data; - - data = (uchar)(val & 0xff); - - if (i2c_write(dcp->i2c_addr, reg, 1, &data, 1) != 0) - return 1; - - return 0; -} /* dtt_write() */ - -int -dtt_init_one(int sensor) -{ - dtt_cfg_t *dcp = &dttcfg[sensor >> 1]; - int reg, val; - - if (((sensor & 1) == 0 ? dcp->enable_local : dcp->enable_remote) == 0) - return 1; /* sensor is disabled (or rather ignored) */ - - /* - * Setup High Limit register - */ - if ((sensor & 1) == 0) { - reg = DTT_WRITE_LOC_HIGHLIM; - val = dcp->max_local; - } - else { - reg = DTT_WRITE_REM_HIGHLIM; - val = dcp->max_remote; - } - if (dtt_write (sensor, reg, val) != 0) - return 1; - - /* - * Setup Low Limit register - */ - if ((sensor & 1) == 0) { - reg = DTT_WRITE_LOC_LOWLIM; - val = dcp->min_local; - } - else { - reg = DTT_WRITE_REM_LOWLIM; - val = dcp->min_remote; - } - if (dtt_write (sensor, reg, val) != 0) - return 1; - - /* shouldn't hurt if the rest gets done twice */ - - /* - * Setup Conversion Rate register - */ - if (dtt_write (sensor, DTT_WRITE_CONVRATE, dcp->conv_rate) != 0) - return 1; - - /* - * Setup configuraton register - */ - val = 0; /* running */ - if (dcp->enable_alert == 0) - val |= DTT_CONFIG_ALERT_MASKED; /* mask ALERT pin */ - if (dtt_write (sensor, DTT_WRITE_CONFIG, val) != 0) - return 1; - - return 0; -} /* dtt_init_one() */ - -int -dtt_get_temp (int sensor) -{ - signed char val; - - if ((sensor & 1) == 0) - val = dtt_read(sensor, DTT_READ_LOC_VALUE); - else - val = dtt_read(sensor, DTT_READ_REM_VALUE); - - return (int) val; -} /* dtt_get_temp() */ diff --git a/drivers/hwmon/adt7460.c b/drivers/hwmon/adt7460.c deleted file mode 100644 index 9b2c5b69ce..0000000000 --- a/drivers/hwmon/adt7460.c +++ /dev/null @@ -1,73 +0,0 @@ -/* - * (C) Copyright 2008 - * Ricado Ribalda-Universidad Autonoma de Madrid, ricardo.ribalda@gmail.com - * This work has been supported by: QTechnology http://qtec.com/ - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include - -#define ADT7460_ADDRESS 0x2c -#define ADT7460_INVALID 128 -#define ADT7460_CONFIG 0x40 -#define ADT7460_REM1_TEMP 0x25 -#define ADT7460_LOCAL_TEMP 0x26 -#define ADT7460_REM2_TEMP 0x27 - -int dtt_read(int sensor, int reg) -{ - u8 dir = reg; - u8 data; - - if (i2c_read(ADT7460_ADDRESS, dir, 1, &data, 1) == -1) - return -1; - if (data == ADT7460_INVALID) - return -1; - - return data; -} - -int dtt_write(int sensor, int reg, int val) -{ - u8 dir = reg; - u8 data = val; - - if (i2c_write(ADT7460_ADDRESS, dir, 1, &data, 1) == -1) - return -1; - - return 0; -} - -int dtt_init_one(int sensor) -{ - printf("ADT7460 at I2C address 0x%2x\n", ADT7460_ADDRESS); - - if (dtt_write(0, ADT7460_CONFIG, 1) == -1) { - puts("Error initialiting ADT7460\n"); - return -1; - } - - return 0; -} - -int dtt_get_temp(int sensor) -{ - int aux; - u8 table[] = - { ADT7460_REM1_TEMP, ADT7460_LOCAL_TEMP, ADT7460_REM2_TEMP }; - - if (sensor > 2) { - puts("DTT sensor does not exist\n"); - return -1; - } - - aux = dtt_read(0, table[sensor]); - if (aux == -1) { - puts("DTT temperature read failed\n"); - return -1; - } - - return aux; -} diff --git a/drivers/hwmon/ds1621.c b/drivers/hwmon/ds1621.c deleted file mode 100644 index 66947a664e..0000000000 --- a/drivers/hwmon/ds1621.c +++ /dev/null @@ -1,155 +0,0 @@ -/* - * (C) Copyright 2001 - * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Dallas Semiconductor's DS1621/1631 Digital Thermometer and Thermostat. - */ - -#include -#include -#include - -/* - * Device code - */ -#define DTT_I2C_DEV_CODE 0x48 /* Dallas Semi's DS1621 */ -#define DTT_READ_TEMP 0xAA -#define DTT_READ_COUNTER 0xA8 -#define DTT_READ_SLOPE 0xA9 -#define DTT_WRITE_START_CONV 0xEE -#define DTT_WRITE_STOP_CONV 0x22 -#define DTT_TEMP_HIGH 0xA1 -#define DTT_TEMP_LOW 0xA2 -#define DTT_CONFIG 0xAC - -/* - * Config register bits - */ -#define DTT_CONFIG_1SHOT 0x01 -#define DTT_CONFIG_POLARITY 0x02 -#define DTT_CONFIG_R0 0x04 /* ds1631 only */ -#define DTT_CONFIG_R1 0x08 /* ds1631 only */ -#define DTT_CONFIG_NVB 0x10 -#define DTT_CONFIG_TLF 0x20 -#define DTT_CONFIG_THF 0x40 -#define DTT_CONFIG_DONE 0x80 - - -int dtt_read(int sensor, int reg) -{ - int dlen; - uchar data[2]; - - /* Calculate sensor address and command */ - sensor = DTT_I2C_DEV_CODE + (sensor & 0x07); /* Calculate addr of ds1621*/ - - /* Prepare to handle 2 byte result */ - switch(reg) { - case DTT_READ_TEMP: - case DTT_TEMP_HIGH: - case DTT_TEMP_LOW: - dlen = 2; - break; - default: - dlen = 1; - } - - /* Now try to read the register */ - if (i2c_read(sensor, reg, 1, data, dlen) != 0) - return 1; - - /* Handle 2 byte result */ - if (dlen == 2) - return (short)((data[0] << 8) | data[1]); - - return (int)data[0]; -} - - -int dtt_write(int sensor, int reg, int val) -{ - int dlen; - uchar data[2]; - - /* Calculate sensor address and register */ - sensor = DTT_I2C_DEV_CODE + (sensor & 0x07); - - /* Handle various data sizes. */ - switch(reg) { - case DTT_READ_TEMP: - case DTT_TEMP_HIGH: - case DTT_TEMP_LOW: - dlen = 2; - data[0] = (char)((val >> 8) & 0xff); /* MSB first */ - data[1] = (char)(val & 0xff); - break; - case DTT_WRITE_START_CONV: - case DTT_WRITE_STOP_CONV: - dlen = 0; - data[0] = (char)0; - data[1] = (char)0; - break; - default: - dlen = 1; - data[0] = (char)(val & 0xff); - } - - /* Write value to device */ - if (i2c_write(sensor, reg, 1, data, dlen) != 0) - return 1; - - /* Poll NV memory busy bit in case write was to register stored in EEPROM */ - while(i2c_reg_read(sensor, DTT_CONFIG) & DTT_CONFIG_NVB) - ; - - return 0; -} - - -int dtt_init_one(int sensor) -{ - int val; - - /* Setup High Temp */ - val = ((CONFIG_SYS_DTT_MAX_TEMP * 2) << 7) & 0xff80; - if (dtt_write(sensor, DTT_TEMP_HIGH, val) != 0) - return 1; - - /* Setup Low Temp - hysteresis */ - val = (((CONFIG_SYS_DTT_MAX_TEMP - CONFIG_SYS_DTT_HYSTERESIS) * 2) << 7) & 0xff80; - if (dtt_write(sensor, DTT_TEMP_LOW, val) != 0) - return 1; - - /* - * Setup configuraton register - * - * Clear THF & TLF, Reserved = 1, Polarity = Active Low, One Shot = YES - * - * We run in polled mode, since there isn't any way to know if this - * lousy device is ready to provide temperature readings on power up. - */ - val = 0x9; - if (dtt_write(sensor, DTT_CONFIG, val) != 0) - return 1; - - return 0; -} - -int dtt_get_temp(int sensor) -{ - int i; - - /* Start a conversion, may take up to 1 second. */ - dtt_write(sensor, DTT_WRITE_START_CONV, 0); - for (i = 0; i <= 10; i++) { - udelay(100000); - if (dtt_read(sensor, DTT_CONFIG) & DTT_CONFIG_DONE) - break; - } - - return (dtt_read(sensor, DTT_READ_TEMP) / 256); -} diff --git a/drivers/hwmon/ds1722.c b/drivers/hwmon/ds1722.c deleted file mode 100644 index c46958846c..0000000000 --- a/drivers/hwmon/ds1722.c +++ /dev/null @@ -1,137 +0,0 @@ -#include -#include -#include - -static void ds1722_select(int dev) -{ - ssi_set_interface(4096, 0, 0, 0); - ssi_chip_select(0); - udelay(1); - ssi_chip_select(dev); - udelay(1); -} - - -u8 ds1722_read(int dev, int addr) -{ - u8 res; - - ds1722_select(dev); - - ssi_tx_byte(addr); - res = ssi_rx_byte(); - - ssi_chip_select(0); - - return res; -} - -void ds1722_write(int dev, int addr, u8 data) -{ - ds1722_select(dev); - - ssi_tx_byte(0x80|addr); - ssi_tx_byte(data); - - ssi_chip_select(0); -} - - -u16 ds1722_temp(int dev, int resolution) -{ - static int useconds[] = { - 75000, 150000, 300000, 600000, 1200000 - }; - char temp; - u16 res; - - - /* set up the desired resulotion ... */ - ds1722_write(dev, 0, 0xe0 | (resolution << 1)); - - /* wait while the chip measures the tremperature */ - udelay(useconds[resolution]); - - res = (temp = ds1722_read(dev, 2)) << 8; - - if (temp < 0) { - temp = (16 - (ds1722_read(dev, 1) >> 4)) & 0x0f; - } else { - temp = (ds1722_read(dev, 1) >> 4); - } - - switch (temp) { - case 0: - /* .0000 */ - break; - case 1: - /* .0625 */ - res |=1; - break; - case 2: - /* .1250 */ - res |=1; - break; - case 3: - /* .1875 */ - res |=2; - break; - case 4: - /* .2500 */ - res |=3; - break; - case 5: - /* .3125 */ - res |=3; - break; - case 6: - /* .3750 */ - res |=4; - break; - case 7: - /* .4375 */ - res |=4; - break; - case 8: - /* .5000 */ - res |=5; - break; - case 9: - /* .5625 */ - res |=6; - break; - case 10: - /* .6250 */ - res |=6; - break; - case 11: - /* .6875 */ - res |=7; - break; - case 12: - /* .7500 */ - res |=8; - break; - case 13: - /* .8125 */ - res |=8; - break; - case 14: - /* .8750 */ - res |=9; - break; - case 15: - /* .9375 */ - res |=9; - break; - } - return res; - -} - -int ds1722_probe(int dev) -{ - u16 temp = ds1722_temp(dev, DS1722_RESOLUTION_12BIT); - printf("%d.%d deg C\n\n", (char)(temp >> 8), temp & 0xff); - return 0; -} diff --git a/drivers/hwmon/ds1775.c b/drivers/hwmon/ds1775.c deleted file mode 100644 index 4c0c0b82a0..0000000000 --- a/drivers/hwmon/ds1775.c +++ /dev/null @@ -1,126 +0,0 @@ -/* - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Dallas Semiconductor's DS1775 Digital Thermometer and Thermostat - */ - -#include - -#include -#include - -#define DTT_I2C_DEV_CODE 0x48 /* Dallas Semi's DS1775 device code */ -#define DTT_READ_TEMP 0x0 -#define DTT_CONFIG 0x1 -#define DTT_TEMP_HYST 0x2 -#define DTT_TEMP_OS 0x3 - -int dtt_read(int sensor, int reg) -{ - int dlen; - uchar data[2]; - - /* - * Calculate sensor address and command - */ - sensor = DTT_I2C_DEV_CODE + (sensor & 0x07); /* Calculate addr of ds1775 */ - - /* - * Prepare to handle 2 byte result - */ - if ((reg == DTT_READ_TEMP) || - (reg == DTT_TEMP_OS) || (reg == DTT_TEMP_HYST)) - dlen = 2; - else - dlen = 1; - - /* - * Now try to read the register - */ - if (i2c_read(sensor, reg, 1, data, dlen) != 0) - return 1; - - /* - * Handle 2 byte result - */ - if (dlen == 2) - return ((int)((short)data[1] + (((short)data[0]) << 8))); - - return (int) data[0]; -} - - -int dtt_write(int sensor, int reg, int val) -{ - int dlen; - uchar data[2]; - - /* - * Calculate sensor address and register - */ - sensor = DTT_I2C_DEV_CODE + (sensor & 0x07); - - /* - * Handle various data sizes - */ - if ((reg == DTT_READ_TEMP) || - (reg == DTT_TEMP_OS) || (reg == DTT_TEMP_HYST)) { - dlen = 2; - data[0] = (char)((val >> 8) & 0xff); /* MSB first */ - data[1] = (char)(val & 0xff); - } else { - dlen = 1; - data[0] = (char)(val & 0xff); - } - - /* - * Write value to device - */ - if (i2c_write(sensor, reg, 1, data, dlen) != 0) - return 1; - - return 0; -} - - -int dtt_init_one(int sensor) -{ - int val; - - /* - * Setup High Temp - */ - val = ((CONFIG_SYS_DTT_MAX_TEMP * 2) << 7) & 0xff80; - if (dtt_write(sensor, DTT_TEMP_OS, val) != 0) - return 1; - udelay(50000); /* Max 50ms */ - - /* - * Setup Low Temp - hysteresis - */ - val = (((CONFIG_SYS_DTT_MAX_TEMP - CONFIG_SYS_DTT_HYSTERESIS) * 2) << 7) & 0xff80; - if (dtt_write(sensor, DTT_TEMP_HYST, val) != 0) - return 1; - udelay(50000); /* Max 50ms */ - - /* - * Setup configuraton register - * - * Fault Tolerance limits 4, Thermometer resolution bits is 9, - * Polarity = Active Low,continuous conversion mode, Thermostat - * mode is interrupt mode - */ - val = 0xa; - if (dtt_write(sensor, DTT_CONFIG, val) != 0) - return 1; - udelay(50000); /* Max 50ms */ - - return 0; -} - -int dtt_get_temp(int sensor) -{ - return (dtt_read(sensor, DTT_READ_TEMP) / 256); -} diff --git a/drivers/hwmon/ds620.c b/drivers/hwmon/ds620.c deleted file mode 100644 index 1ecc3da799..0000000000 --- a/drivers/hwmon/ds620.c +++ /dev/null @@ -1,65 +0,0 @@ -/* - * DS620 DTT support - * - * (C) Copyright 2014 3ADEV - * Written-by: Albert ARIBAUD - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Dallas Semiconductor's DS1621/1631 Digital Thermometer and Thermostat. - */ - -#include -#include -#include - -/* - * Device code - */ -#define DTT_I2C_DEV_CODE 0x48 -#define DTT_START_CONVERT 0x51 -#define DTT_TEMP 0xAA -#define DTT_CONFIG 0xAC - -/* - * Config register MSB bits - */ -#define DTT_CONFIG_1SHOT 0x01 -#define DTT_CONFIG_AUTOC 0x02 -#define DTT_CONFIG_R0 0x04 /* always 1 */ -#define DTT_CONFIG_R1 0x08 /* always 1 */ -#define DTT_CONFIG_TLF 0x10 -#define DTT_CONFIG_THF 0x20 -#define DTT_CONFIG_NVB 0x40 -#define DTT_CONFIG_DONE 0x80 - -#define CHIP(sensor) (DTT_I2C_DEV_CODE + (sensor & 0x07)) - -int dtt_init_one(int sensor) -{ - uint8_t config = DTT_CONFIG_1SHOT - | DTT_CONFIG_R0 - | DTT_CONFIG_R1; - return i2c_write(CHIP(sensor), DTT_CONFIG, 1, &config, 1); -} - -int dtt_get_temp(int sensor) -{ - uint8_t status; - uint8_t temp[2]; - - /* Start a conversion, may take up to 1 second. */ - i2c_write(CHIP(sensor), DTT_START_CONVERT, 1, NULL, 0); - do { - if (i2c_read(CHIP(sensor), DTT_CONFIG, 1, &status, 1)) - /* bail out if I2C error */ - status |= DTT_CONFIG_DONE; - } while (!(status & DTT_CONFIG_DONE)); - if (i2c_read(CHIP(sensor), DTT_TEMP, 1, temp, 2)) - /* bail out if I2C error */ - return -274; /* below absolute zero == error */ - - return ((int16_t)(temp[1] | (temp[0] << 8))) >> 7; -} diff --git a/drivers/hwmon/lm63.c b/drivers/hwmon/lm63.c deleted file mode 100644 index 053c785fc5..0000000000 --- a/drivers/hwmon/lm63.c +++ /dev/null @@ -1,160 +0,0 @@ -/* - * (C) Copyright 2007-2008 - * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de - * based on lm75.c by Bill Hunter - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * National LM63/LM64 Temperature Sensor - * Main difference: LM 64 has -16 Kelvin temperature offset - */ - -#include -#include -#include - -#define DTT_I2C_LM63_ADDR 0x4C /* National LM63 device */ - -#define DTT_READ_TEMP_RMT_MSB 0x01 -#define DTT_CONFIG 0x03 -#define DTT_READ_TEMP_RMT_LSB 0x10 -#define DTT_TACHLIM_LSB 0x48 -#define DTT_TACHLIM_MSB 0x49 -#define DTT_FAN_CONFIG 0x4A -#define DTT_PWM_FREQ 0x4D -#define DTT_PWM_LOOKUP_BASE 0x50 - -struct pwm_lookup_entry { - u8 temp; - u8 pwm; -}; - -/* - * Device code - */ - -int dtt_read(int sensor, int reg) -{ - int dlen; - uchar data[2]; - - /* - * Calculate sensor address and register. - */ - if (!sensor) - sensor = DTT_I2C_LM63_ADDR; /* legacy config */ - - dlen = 1; - - /* - * Now try to read the register. - */ - if (i2c_read(sensor, reg, 1, data, dlen) != 0) - return -1; - - return (int)data[0]; -} /* dtt_read() */ - -int dtt_write(int sensor, int reg, int val) -{ - int dlen; - uchar data[2]; - - /* - * Calculate sensor address and register. - */ - if (!sensor) - sensor = DTT_I2C_LM63_ADDR; /* legacy config */ - - dlen = 1; - data[0] = (char)(val & 0xff); - - /* - * Write value to register. - */ - if (i2c_write(sensor, reg, 1, data, dlen) != 0) - return 1; - - return 0; -} /* dtt_write() */ - -static int is_lm64(int sensor) -{ - return sensor && (sensor != DTT_I2C_LM63_ADDR); -} - -int dtt_init_one(int sensor) -{ - int i; - int val; - - struct pwm_lookup_entry pwm_lookup[] = CONFIG_DTT_PWM_LOOKUPTABLE; - - /* - * Set PWM Frequency to 2.5% resolution - */ - val = 20; - if (dtt_write(sensor, DTT_PWM_FREQ, val) != 0) - return 1; - - /* - * Set Tachometer Limit - */ - val = CONFIG_DTT_TACH_LIMIT; - if (dtt_write(sensor, DTT_TACHLIM_LSB, val & 0xff) != 0) - return 1; - if (dtt_write(sensor, DTT_TACHLIM_MSB, (val >> 8) & 0xff) != 0) - return 1; - - /* - * Make sure PWM Lookup-Table is writeable - */ - if (dtt_write(sensor, DTT_FAN_CONFIG, 0x20) != 0) - return 1; - - /* - * Setup PWM Lookup-Table - */ - for (i = 0; i < ARRAY_SIZE(pwm_lookup); i++) { - int address = DTT_PWM_LOOKUP_BASE + 2 * i; - val = pwm_lookup[i].temp; - if (is_lm64(sensor)) - val -= 16; - if (dtt_write(sensor, address, val) != 0) - return 1; - val = dtt_read(sensor, address); - val = pwm_lookup[i].pwm; - if (dtt_write(sensor, address + 1, val) != 0) - return 1; - } - - /* - * Enable PWM Lookup-Table, PWM Clock 360 kHz, Tachometer Mode 2 - */ - val = 0x02; - if (dtt_write(sensor, DTT_FAN_CONFIG, val) != 0) - return 1; - - /* - * Enable Tach input - */ - val = dtt_read(sensor, DTT_CONFIG) | 0x04; - if (dtt_write(sensor, DTT_CONFIG, val) != 0) - return 1; - - return 0; -} - -int dtt_get_temp(int sensor) -{ - s16 temp = (dtt_read(sensor, DTT_READ_TEMP_RMT_MSB) << 8) - | (dtt_read(sensor, DTT_READ_TEMP_RMT_LSB)); - - if (is_lm64(sensor)) - temp += 16 << 8; - - /* Ignore LSB for now, U-Boot only prints natural numbers */ - return temp >> 8; -} diff --git a/drivers/hwmon/lm73.c b/drivers/hwmon/lm73.c deleted file mode 100644 index c15c7514d8..0000000000 --- a/drivers/hwmon/lm73.c +++ /dev/null @@ -1,146 +0,0 @@ -/* - * (C) Copyright 2007-2008 - * Larry Johnson, lrj@acm.org - * - * based on dtt/lm75.c which is ... - * - * (C) Copyright 2001 - * Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * National Semiconductor LM73 Temperature Sensor - */ - -#include -#include -#include - -/* - * Device code - */ -#define DTT_I2C_DEV_CODE 0x48 /* National Semi's LM73 device */ -#define DTT_READ_TEMP 0x0 -#define DTT_CONFIG 0x1 -#define DTT_TEMP_HIGH 0x2 -#define DTT_TEMP_LOW 0x3 -#define DTT_CONTROL 0x4 -#define DTT_ID 0x7 - -int dtt_read(int const sensor, int const reg) -{ - int dlen; - uint8_t data[2]; - - /* - * Validate 'reg' param and get register size. - */ - switch (reg) { - case DTT_CONFIG: - case DTT_CONTROL: - dlen = 1; - break; - case DTT_READ_TEMP: - case DTT_TEMP_HIGH: - case DTT_TEMP_LOW: - case DTT_ID: - dlen = 2; - break; - default: - return -1; - } - /* - * Try to read the register at the calculated sensor address. - */ - if (0 != - i2c_read(DTT_I2C_DEV_CODE + (sensor & 0x07), reg, 1, data, dlen)) - return -1; - /* - * Handle 2 byte result. - */ - if (2 == dlen) - return (int)((unsigned)data[0] << 8 | (unsigned)data[1]); - - return (int)data[0]; -} /* dtt_read() */ - -int dtt_write(int const sensor, int const reg, int const val) -{ - int dlen; - uint8_t data[2]; - - /* - * Validate 'reg' param and handle register size - */ - switch (reg) { - case DTT_CONFIG: - case DTT_CONTROL: - dlen = 1; - data[0] = (uint8_t) val; - break; - case DTT_TEMP_HIGH: - case DTT_TEMP_LOW: - dlen = 2; - data[0] = (uint8_t) (val >> 8); /* MSB first */ - data[1] = (uint8_t) val; - break; - default: - return -1; - } - /* - * Write value to register at the calculated sensor address. - */ - return 0 != i2c_write(DTT_I2C_DEV_CODE + (sensor & 0x07), reg, 1, data, - dlen); -} /* dtt_write() */ - -int dtt_init_one(int const sensor) -{ - int val; - - /* - * Validate the Identification register - */ - if (0x0190 != dtt_read(sensor, DTT_ID)) - return -1; - /* - * Setup THIGH (upper-limit) and TLOW (lower-limit) registers - */ - val = CONFIG_SYS_DTT_MAX_TEMP << 7; - if (dtt_write(sensor, DTT_TEMP_HIGH, val)) - return -1; - - val = CONFIG_SYS_DTT_MIN_TEMP << 7; - if (dtt_write(sensor, DTT_TEMP_LOW, val)) - return -1; - /* - * Setup configuraton register - */ - /* config = alert active low, disabled, and reset */ - val = 0x64; - if (dtt_write(sensor, DTT_CONFIG, val)) - return -1; - /* - * Setup control/status register - */ - /* control = temp resolution 0.25C */ - val = 0x00; - if (dtt_write(sensor, DTT_CONTROL, val)) - return -1; - - dtt_read(sensor, DTT_CONTROL); /* clear temperature flags */ - return 0; -} /* dtt_init_one() */ - -int dtt_get_temp(int const sensor) -{ - int const ret = dtt_read(sensor, DTT_READ_TEMP); - - if (ret < 0) { - printf("DTT temperature read failed.\n"); - return 0; - } - return (int)((int16_t) ret + 0x0040) >> 7; -} /* dtt_get_temp() */ diff --git a/drivers/hwmon/lm75.c b/drivers/hwmon/lm75.c deleted file mode 100644 index aafa4757b1..0000000000 --- a/drivers/hwmon/lm75.c +++ /dev/null @@ -1,139 +0,0 @@ -/* - * (C) Copyright 2001 - * Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * On Semiconductor's LM75 Temperature Sensor - */ - -#include -#include -#include - -/* - * Device code - */ -#define DTT_I2C_DEV_CODE 0x48 /* ON Semi's LM75 device */ -#define DTT_READ_TEMP 0x0 -#define DTT_CONFIG 0x1 -#define DTT_TEMP_HYST 0x2 -#define DTT_TEMP_SET 0x3 - -int dtt_read(int sensor, int reg) -{ - int dlen; - uchar data[2]; - -#ifdef CONFIG_DTT_AD7414 - /* - * On AD7414 the first value upon bootup is not read correctly. - * This is most likely because of the 800ms update time of the - * temp register in normal update mode. To get current values - * each time we issue the "dtt" command including upon powerup - * we switch into one-short mode. - * - * Issue one-shot mode command - */ - dtt_write(sensor, DTT_CONFIG, 0x64); -#endif - - /* Validate 'reg' param */ - if((reg < 0) || (reg > 3)) - return -1; - - /* Calculate sensor address and register. */ - sensor = DTT_I2C_DEV_CODE + (sensor & 0x07); - - /* Prepare to handle 2 byte result. */ - if ((reg == DTT_READ_TEMP) || - (reg == DTT_TEMP_HYST) || - (reg == DTT_TEMP_SET)) - dlen = 2; - else - dlen = 1; - - /* Now try to read the register. */ - if (i2c_read(sensor, reg, 1, data, dlen) != 0) - return -1; - - /* Handle 2 byte result. */ - if (dlen == 2) - return ((int)((short)data[1] + (((short)data[0]) << 8))); - - return (int)data[0]; -} /* dtt_read() */ - - -int dtt_write(int sensor, int reg, int val) -{ - int dlen; - uchar data[2]; - - /* Validate 'reg' param */ - if ((reg < 0) || (reg > 3)) - return 1; - - /* Calculate sensor address and register. */ - sensor = DTT_I2C_DEV_CODE + (sensor & 0x07); - - /* Handle 2 byte values. */ - if ((reg == DTT_READ_TEMP) || - (reg == DTT_TEMP_HYST) || - (reg == DTT_TEMP_SET)) { - dlen = 2; - data[0] = (char)((val >> 8) & 0xff); /* MSB first */ - data[1] = (char)(val & 0xff); - } else { - dlen = 1; - data[0] = (char)(val & 0xff); - } - - /* Write value to register. */ - if (i2c_write(sensor, reg, 1, data, dlen) != 0) - return 1; - - return 0; -} /* dtt_write() */ - - -int dtt_init_one(int sensor) -{ - int val; - - /* Setup TSET ( trip point ) register */ - val = ((CONFIG_SYS_DTT_MAX_TEMP * 2) << 7) & 0xff80; /* trip */ - if (dtt_write(sensor, DTT_TEMP_SET, val) != 0) - return 1; - - /* Setup THYST ( untrip point ) register - Hysteresis */ - val = (((CONFIG_SYS_DTT_MAX_TEMP - CONFIG_SYS_DTT_HYSTERESIS) * 2) << 7) & 0xff80; - if (dtt_write(sensor, DTT_TEMP_HYST, val) != 0) - return 1; - - /* Setup configuraton register */ -#ifdef CONFIG_DTT_AD7414 - /* config = alert active low and disabled */ - val = 0x60; -#else - /* config = 6 sample integration, int mode, active low, and enable */ - val = 0x18; -#endif - if (dtt_write(sensor, DTT_CONFIG, val) != 0) - return 1; - - return 0; -} /* dtt_init_one() */ - -int dtt_get_temp(int sensor) -{ - int const ret = dtt_read(sensor, DTT_READ_TEMP); - - if (ret < 0) { - printf("DTT temperature read failed.\n"); - return 0; - } - return (int)((int16_t) ret / 256); -} /* dtt_get_temp() */ diff --git a/drivers/hwmon/lm81.c b/drivers/hwmon/lm81.c deleted file mode 100644 index bcc8d3293b..0000000000 --- a/drivers/hwmon/lm81.c +++ /dev/null @@ -1,111 +0,0 @@ -/* - * (C) Copyright 2006 - * Heiko Schocher, DENX Software Enginnering - * - * based on dtt/lm75.c which is ... - * - * (C) Copyright 2001 - * Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * On Semiconductor's LM81 Temperature Sensor - */ - -#include -#include -#include - -/* - * Device code - */ -#define DTT_I2C_DEV_CODE 0x2c /* ON Semi's LM81 device */ -#define DTT_READ_TEMP 0x27 -#define DTT_CONFIG_TEMP 0x4b -#define DTT_TEMP_MAX 0x39 -#define DTT_TEMP_HYST 0x3a -#define DTT_CONFIG 0x40 - -int dtt_read(int sensor, int reg) -{ - int dlen = 1; - uchar data[2]; - - /* - * Calculate sensor address and register. - */ - sensor = DTT_I2C_DEV_CODE + (sensor & 0x03); /* calculate address of lm81 */ - - /* - * Now try to read the register. - */ - if (i2c_read(sensor, reg, 1, data, dlen) != 0) - return -1; - - return (int)data[0]; -} /* dtt_read() */ - - -int dtt_write(int sensor, int reg, int val) -{ - uchar data; - - /* - * Calculate sensor address and register. - */ - sensor = DTT_I2C_DEV_CODE + (sensor & 0x03); /* calculate address of lm81 */ - - data = (char)(val & 0xff); - - /* - * Write value to register. - */ - if (i2c_write(sensor, reg, 1, &data, 1) != 0) - return 1; - - return 0; -} /* dtt_write() */ - -#define DTT_MANU 0x3e -#define DTT_REV 0x3f -#define DTT_CONFIG 0x40 -#define DTT_ADR 0x48 - -int dtt_init_one(int sensor) -{ - int man; - int adr; - int rev; - - if (dtt_write (sensor, DTT_CONFIG, 0x01) < 0) - return 1; - /* The LM81 needs 400ms to get the correct values ... */ - udelay (400000); - man = dtt_read (sensor, DTT_MANU); - if (man != 0x01) - return 1; - adr = dtt_read (sensor, DTT_ADR); - if (adr < 0) - return 1; - rev = dtt_read (sensor, DTT_REV); - if (rev < 0) - return 1; - - debug ("DTT: Found LM81@%x Rev: %d\n", adr, rev); - return 0; -} /* dtt_init_one() */ - - -#define TEMP_FROM_REG(temp) \ - ((temp)<256?((((temp)&0x1fe) >> 1) * 10) + ((temp) & 1) * 5: \ - ((((temp)&0x1fe) >> 1) -255) * 10 - ((temp) & 1) * 5) \ - -int dtt_get_temp(int sensor) -{ - int val = dtt_read (sensor, DTT_READ_TEMP); - int tmpcnf = dtt_read (sensor, DTT_CONFIG_TEMP); - - return (TEMP_FROM_REG((val << 1) + ((tmpcnf & 0x80) >> 7))) / 10; -} /* dtt_get_temp() */ diff --git a/include/config_cmd_all.h b/include/config_cmd_all.h index bc0bc2b6c8..95c05350cd 100644 --- a/include/config_cmd_all.h +++ b/include/config_cmd_all.h @@ -13,7 +13,6 @@ * Alphabetical list of all possible commands. */ -#define CONFIG_CMD_DTT /* Digital Therm and Thermostat */ #define CONFIG_CMD_EEPROM /* EEPROM read/write support */ #define CONFIG_CMD_FDC /* Floppy Disk Support */ #define CONFIG_CMD_FUSE /* Device fuse support */ diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h index b9599b5e3b..8628b7ed18 100644 --- a/include/configs/PMC440.h +++ b/include/configs/PMC440.h @@ -163,26 +163,6 @@ #define CONFIG_SYS_EEPROM_WREN 1 #define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52 -/* - * standard dtt sensor configuration - bottom bit will determine local or - * remote sensor of the TMP401 - */ -#define CONFIG_DTT_SENSORS { 0, 1 } - -/* - * The PMC440 uses a TI TMP401 temperature sensor. This part - * is basically compatible to the ADM1021 that is supported - * by U-Boot. - * - * - i2c addr 0x4c - * - conversion rate 0x02 = 0.25 conversions/second - * - ALERT ouput disabled - * - local temp sensor enabled, min set to 0 deg, max set to 70 deg - * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg - */ -#define CONFIG_DTT_ADM1021 -#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} } - #define CONFIG_PREBOOT "echo Add \\\"run fpga\\\" and " \ "\\\"painit\\\" to preboot command" @@ -258,7 +238,6 @@ /* Partitions */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h index e3c2cca3c3..df6386c602 100644 --- a/include/configs/TQM834x.h +++ b/include/configs/TQM834x.h @@ -184,13 +184,6 @@ #define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */ #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ -/* I2C SYSMON (LM75) */ -#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 - /* * TSEC */ @@ -280,7 +273,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h index cd46db4f6f..8265f3c1ab 100644 --- a/include/configs/UCP1020.h +++ b/include/configs/UCP1020.h @@ -129,27 +129,6 @@ #define CONFIG_HWCONFIG -#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ -#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ -#define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */ -/* - * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details). - * there will be one entry in this array for each two (dummy) sensors in - * CONFIG_DTT_SENSORS. - * - * For uCP1020 module: - * - only one ADM1021/NCT72 - * - i2c addr 0x41 - * - conversion rate 0x02 = 0.25 conversions/second - * - ALERT output disabled - * - local temp sensor enabled, min set to 0 deg, max set to 85 deg - * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg - */ -#define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \ - 0x02, 0, 1, 0, 85, 1, 0, 85} } - -#define CONFIG_CMD_DTT - /* * These can be toggled for performance analysis, otherwise use default. */ diff --git a/include/configs/acadia.h b/include/configs/acadia.h index 9f35e71d0c..0be310d4a3 100644 --- a/include/configs/acadia.h +++ b/include/configs/acadia.h @@ -124,14 +124,6 @@ #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 1 /* use AD7414 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 - /*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/ @@ -160,7 +152,6 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND /*----------------------------------------------------------------------- diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index ea440d6e16..b495d0645b 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -261,14 +261,6 @@ #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 #define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 /* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 /* use AD7414 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 - #if !defined(CONFIG_ARCHES) /* RTC configuration */ #define CONFIG_RTC_M41T62 @@ -369,17 +361,14 @@ * Commands additional to the ones defined in amcc-common.h */ #if defined(CONFIG_ARCHES) -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM #elif defined(CONFIG_CANYONLANDS) -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SATA #define CONFIG_CMD_SDRAM #elif defined(CONFIG_GLACIER) -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM diff --git a/include/configs/dlvision-10g.h b/include/configs/dlvision-10g.h index c5e227650e..9fb5cdeb5a 100644 --- a/include/configs/dlvision-10g.h +++ b/include/configs/dlvision-10g.h @@ -54,7 +54,6 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM #undef CONFIG_CMD_IRQ @@ -108,13 +107,6 @@ #define CONFIG_SYS_SPD_BUS_NUM 4 /* Temp sensor/hwmon/dtt */ -#define CONFIG_SYS_DTT_BUS_NUM 4 -#define CONFIG_DTT_LM63 1 /* National LM63 */ -#define CONFIG_DTT_SENSORS { 0x4c, 0x4e, 0x18 } /* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 46, 10 }, { 48, 14 }, { 50, 19 }, { 52, 23 },\ - { 54, 27 }, { 56, 31 }, { 58, 36 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 #define CONFIG_SYS_ICS8N3QV01_I2C {1, 3} #define CONFIG_SYS_SIL1178_I2C {0, 2} diff --git a/include/configs/dlvision.h b/include/configs/dlvision.h index f8d390ba33..09d911374d 100644 --- a/include/configs/dlvision.h +++ b/include/configs/dlvision.h @@ -52,7 +52,6 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM #undef CONFIG_CMD_IRQ diff --git a/include/configs/exynos5-common.h b/include/configs/exynos5-common.h index f893b2e347..f4a56f27d5 100644 --- a/include/configs/exynos5-common.h +++ b/include/configs/exynos5-common.h @@ -45,8 +45,6 @@ /* Thermal Management Unit */ #define CONFIG_EXYNOS_TMU -#define CONFIG_CMD_DTT -#define CONFIG_TMU_CMD_DTT /* MMC SPL */ #define COPY_BL2_FNPTR_ADDR 0x02020030 diff --git a/include/configs/intip.h b/include/configs/intip.h index f1f840923b..036fd20eb4 100644 --- a/include/configs/intip.h +++ b/include/configs/intip.h @@ -218,13 +218,6 @@ #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 #define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* I2C SYSMON */ -#define CONFIG_DTT_LM63 1 /* National LM63 */ -#define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 50, 20 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 - /* RTC configuration */ #define CONFIG_RTC_DS1337 1 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 @@ -272,7 +265,6 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM diff --git a/include/configs/io.h b/include/configs/io.h index ee2b52a7ed..d4e8d56fd8 100644 --- a/include/configs/io.h +++ b/include/configs/io.h @@ -54,7 +54,6 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM #undef CONFIG_CMD_IRQ @@ -90,11 +89,6 @@ #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 /* Temp sensor/hwmon/dtt */ -#define CONFIG_DTT_LM63 1 /* National LM63 */ -#define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 50, 20 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 /* * FLASH organization diff --git a/include/configs/io64.h b/include/configs/io64.h index 8e754fc10b..1b58f04540 100644 --- a/include/configs/io64.h +++ b/include/configs/io64.h @@ -327,14 +327,6 @@ #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 #define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* Temp sensor/hwmon/dtt */ -#define CONFIG_DTT_LM63 1 /* National LM63 */ -#define CONFIG_DTT_SENSORS { 0x18, 0x4c, 0x4e } /* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 43, 13 }, { 46, 16 }, \ - { 50, 20 }, { 53, 27 }, { 56, 34 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 - /*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/ @@ -373,7 +365,6 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORY diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 3143b631ce..c3b9da0d96 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -123,31 +123,6 @@ #define CONFIG_SYS_I2C_RTC_ADDR 0x68 #define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux */ -/* I2C DTT */ -#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ -#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ -/* - * standard dtt sensor configuration - bottom bit will determine local or - * remote sensor of the ADM1021, the rest determines index into - * CONFIG_SYS_DTT_ADM1021 array below. - */ -#define CONFIG_DTT_SENSORS { 0, 1 } - -/* - * ADM1021 temp sensor configuration (see dtt/adm1021.c for details). - * there will be one entry in this array for each two (dummy) sensors in - * CONFIG_DTT_SENSORS. - * - * For Katmai board: - * - only one ADM1021 - * - i2c addr 0x18 - * - conversion rate 0x02 = 0.25 conversions/second - * - ALERT ouput disabled - * - local temp sensor enabled, min set to 0 deg, max set to 85 deg - * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg - */ -#define CONFIG_SYS_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} } - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index b8c0d0d8f0..a91a6a9ee5 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -317,10 +317,6 @@ #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 #define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* Standard DTT sensor configuration */ -#define CONFIG_DTT_DS1775 1 -#define CONFIG_DTT_SENSORS { 0 } - /* RTC configuration */ #define CONFIG_RTC_DS1338 1 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 diff --git a/include/configs/km/km-powerpc.h b/include/configs/km/km-powerpc.h index 8293607c9c..0d50538a8e 100644 --- a/include/configs/km/km-powerpc.h +++ b/include/configs/km/km-powerpc.h @@ -14,7 +14,6 @@ #define CONFIG_BOOTCOUNT_LIMIT -#define CONFIG_CMD_DTT #define CONFIG_JFFS2_CMDLINE /* standard km ethernet_present for piggy */ diff --git a/include/configs/km/km83xx-common.h b/include/configs/km/km83xx-common.h index 35ec0972bf..7d69224bd1 100644 --- a/include/configs/km/km83xx-common.h +++ b/include/configs/km/km83xx-common.h @@ -215,13 +215,6 @@ #define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0, 1, 2, 3} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM 1 - #if defined(CONFIG_CMD_NAND) #define CONFIG_NAND_KMETER1 #define CONFIG_SYS_MAX_NAND_DEVICE 1 diff --git a/include/configs/km82xx.h b/include/configs/km82xx.h index aeece20bda..09c3aa9ca8 100644 --- a/include/configs/km82xx.h +++ b/include/configs/km82xx.h @@ -268,13 +268,6 @@ int get_sda(void); int get_scl(void); #endif -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM 2 - #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_SYS_IMMR 0xF0000000 diff --git a/include/configs/makalu.h b/include/configs/makalu.h index cdb02f3693..a92bc43538 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -189,10 +189,6 @@ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* Standard DTT sensor configuration */ -#define CONFIG_DTT_DS1775 1 -#define CONFIG_DTT_SENSORS { 0 } - /* RTC configuration */ #define CONFIG_RTC_X1205 1 #define CONFIG_SYS_I2C_RTC_ADDR 0x6f @@ -231,7 +227,6 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI /* POST support */ diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h index cb5c346807..aaa8962fd2 100644 --- a/include/configs/motionpro.h +++ b/include/configs/motionpro.h @@ -33,7 +33,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_IDE #define CONFIG_CMD_IMMAP #define CONFIG_CMD_JFFS2 @@ -268,6 +267,13 @@ #define LED_ON 0x00000010 /* +<<<<<<< 4ba57299158b7a7020d2bd3b8d8369884696a0ae +======= + * Temperature sensor + */ + +/* +>>>>>>> Drop digital thermometer and thermostat (DTT) drivers * Environment settings */ #define CONFIG_ENV_IS_IN_FLASH 1 diff --git a/include/configs/neo.h b/include/configs/neo.h index 1d8e13f035..40a6718025 100644 --- a/include/configs/neo.h +++ b/include/configs/neo.h @@ -54,7 +54,6 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM #undef CONFIG_CMD_IRQ @@ -97,13 +96,6 @@ #define CONFIG_RTC_DS1337 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 -/* Temp sensor/hwmon/dtt */ -#define CONFIG_DTT_LM63 1 /* National LM63 */ -#define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 50, 20 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 - /* * FLASH organization */ diff --git a/include/configs/odroid_xu3.h b/include/configs/odroid_xu3.h index 246fb808a9..ba29f3e7d1 100644 --- a/include/configs/odroid_xu3.h +++ b/include/configs/odroid_xu3.h @@ -61,7 +61,6 @@ /* FIXME: MUST BE REMOVED AFTER TMU IS TURNED ON */ #undef CONFIG_EXYNOS_TMU -#undef CONFIG_TMU_CMD_DTT #define CONFIG_DFU_ALT_SYSTEM \ "uImage fat 0 1;" \ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index c39bb24420..7a120ed5a6 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -159,14 +159,6 @@ #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 #define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 1 /* use AD7414 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 - /* * Default environment variables */ @@ -219,7 +211,6 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM diff --git a/include/configs/socrates.h b/include/configs/socrates.h index 76b4038d50..b37e796d33 100644 --- a/include/configs/socrates.h +++ b/include/configs/socrates.h @@ -210,13 +210,6 @@ /* I2C W83782G HW-Monitoring IC */ #define CONFIG_SYS_I2C_W83782G_ADDR 0x28 /* W83782G address */ -/* I2C temp sensor */ -/* Socrates uses Maxim's DS75, which is compatible with LM75 */ -#define CONFIG_DTT_LM75 1 -#define CONFIG_DTT_SENSORS {4} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 125 -#define CONFIG_SYS_DTT_LOW_TEMP -55 -#define CONFIG_SYS_DTT_HYSTERESIS 3 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* @@ -286,7 +279,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM #define CONFIG_CMD_SDRAM #define CONFIG_CMD_REGINFO diff --git a/include/configs/tqma6.h b/include/configs/tqma6.h index 738693c0c0..799c45e2d7 100644 --- a/include/configs/tqma6.h +++ b/include/configs/tqma6.h @@ -57,13 +57,6 @@ #define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_I2C_SPEED 100000 -/* I2C SYSMON (LM75) */ -#define CONFIG_DTT_LM75 -#define CONFIG_DTT_MAX_TEMP 70 -#define CONFIG_DTT_MIN_TEMP -30 -#define CONFIG_DTT_HYSTERESIS 3 -#define CONFIG_CMD_DTT - /* I2C EEPROM (M24C64) */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 @@ -371,8 +364,5 @@ #endif /* Support at least the sensor on TQMa6 SOM */ -#if !defined(CONFIG_DTT_SENSORS) -#define CONFIG_DTT_SENSORS { 0 } -#endif #endif /* __CONFIG_H */ diff --git a/include/configs/tqma6_mba6.h b/include/configs/tqma6_mba6.h index 3d6e4383e1..69e9079339 100644 --- a/include/configs/tqma6_mba6.h +++ b/include/configs/tqma6_mba6.h @@ -10,8 +10,6 @@ #ifndef __CONFIG_TQMA6_MBA6_H #define __CONFIG_TQMA6_MBA6_H -#define CONFIG_DTT_SENSORS { 0, 1 } - #define CONFIG_FEC_XCV_TYPE RGMII #define CONFIG_ETHPRIME "FEC" diff --git a/include/configs/tqma6_wru4.h b/include/configs/tqma6_wru4.h index b9cc5d632f..4ab4c6559d 100644 --- a/include/configs/tqma6_wru4.h +++ b/include/configs/tqma6_wru4.h @@ -7,10 +7,6 @@ #ifndef __CONFIG_TQMA6_WRU4_H #define __CONFIG_TQMA6_WRU4_H -/* DTT sensors */ -#define CONFIG_DTT_SENSORS { 0, 1 } -#define CONFIG_SYS_DTT_BUS_NUM 2 - /* Ethernet */ #define CONFIG_FEC_XCV_TYPE RMII #define CONFIG_ETHPRIME "FEC" diff --git a/include/configs/work_92105.h b/include/configs/work_92105.h index 81d1fd9ece..c308f2c1a6 100644 --- a/include/configs/work_92105.h +++ b/include/configs/work_92105.h @@ -84,14 +84,6 @@ #define CONFIG_RTC_DS1374 -/* - * I2C Temperature Sensor (DTT) - */ - -#define CONFIG_CMD_DTT -#define CONFIG_DTT_SENSORS { 0, 1 } -#define CONFIG_DTT_DS620 - /* * U-Boot General Configurations */ diff --git a/include/configs/xilinx-ppc.h b/include/configs/xilinx-ppc.h index ea4b739d0b..c4efae67a7 100644 --- a/include/configs/xilinx-ppc.h +++ b/include/configs/xilinx-ppc.h @@ -28,7 +28,6 @@ #define CONFIG_CMD_REGINFO #undef CONFIG_CMD_JFFS2 #undef CONFIG_CMD_MTDPARTS -#undef CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM /*Misc*/ diff --git a/include/configs/xpedite517x.h b/include/configs/xpedite517x.h index bd1d0c75d9..97a9d71e8b 100644 --- a/include/configs/xpedite517x.h +++ b/include/configs/xpedite517x.h @@ -233,8 +233,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* I2C DS1631 temperature sensor */ #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 -#define CONFIG_DTT_DS1621 -#define CONFIG_DTT_SENSORS { 0 } #define CONFIG_SYS_I2C_LM90_ADDR 0x4c /* I2C EEPROM - AT24C128B */ @@ -501,7 +499,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * Command configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ #define CONFIG_CMD_JFFS2 diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h index a290cf3463..fa1971db20 100644 --- a/include/configs/xpedite537x.h +++ b/include/configs/xpedite537x.h @@ -230,8 +230,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* I2C DS1631 temperature sensor */ #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 -#define CONFIG_DTT_DS1621 -#define CONFIG_DTT_SENSORS { 0 } #define CONFIG_SYS_I2C_LM90_ADDR 0x4c /* I2C EEPROM - AT24C128B */ @@ -353,7 +351,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* * Command configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NAND diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h index ad4247ab48..e3f0b939c3 100644 --- a/include/configs/xpedite550x.h +++ b/include/configs/xpedite550x.h @@ -219,8 +219,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C DS7505 temperature sensor */ -#define CONFIG_DTT_LM75 -#define CONFIG_DTT_SENSORS { 0 } #define CONFIG_SYS_I2C_LM75_ADDR 0x48 /* I2C ADT7461 temperature sensor */ @@ -338,7 +336,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* * Command configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NAND diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index 77648d78bc..d9c09b80cd 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -131,14 +131,6 @@ #define CONFIG_ENV_OFFSET 0x0 #endif /* CONFIG_ENV_IS_IN_EEPROM */ -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 1 /* use AD7414 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 - /* * Default environment variables */ @@ -184,7 +176,6 @@ /* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI #ifdef CONFIG_440EP diff --git a/include/dtt.h b/include/dtt.h deleted file mode 100644 index 173159dc62..0000000000 --- a/include/dtt.h +++ /dev/null @@ -1,47 +0,0 @@ -/* - * (C) Copyright 2001 - * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Digital Thermometers and Thermostats. - */ -#ifndef _DTT_H_ -#define _DTT_H_ - -#if defined(CONFIG_DTT_ADM1021) || \ - defined(CONFIG_DTT_ADT7460) || \ - defined(CONFIG_DTT_DS1621) || \ - defined(CONFIG_DTT_DS1775) || \ - defined(CONFIG_DTT_DS620) || \ - defined(CONFIG_DTT_LM63) || \ - defined(CONFIG_DTT_LM73) || \ - defined(CONFIG_DTT_LM75) || \ - defined(CONFIG_DTT_LM81) - -#define CONFIG_DTT /* We have a DTT */ - -#ifndef CONFIG_DTT_ADM1021 -#define DTT_COMMERCIAL_MAX_TEMP 70 /* 0 - +70 C */ -#define DTT_INDUSTRIAL_MAX_TEMP 85 /* -40 - +85 C */ -#define DTT_AUTOMOTIVE_MAX_TEMP 105 /* -40 - +105 C */ - -#ifndef CONFIG_SYS_DTT_MAX_TEMP -#define CONFIG_SYS_DTT_MAX_TEMP DTT_COMMERCIAL_MAX_TEMP -#endif - -#ifndef CONFIG_SYS_DTT_HYSTERESIS -#define CONFIG_SYS_DTT_HYSTERESIS 5 /* 5 C */ -#endif -#endif /* CONFIG_DTT_ADM1021 */ - -extern void dtt_init(void); -extern int dtt_init_one(int); -extern int dtt_read(int sensor, int reg); -extern int dtt_write(int sensor, int reg, int val); -extern int dtt_get_temp(int sensor); -#endif - -#endif /* _DTT_H_ */ diff --git a/include/i2c.h b/include/i2c.h index a88cc7cddf..2c1643d650 100644 --- a/include/i2c.h +++ b/include/i2c.h @@ -571,9 +571,6 @@ void i2c_dump_msgs(struct i2c_msg *msg, int nmsgs); #if !defined(CONFIG_SYS_RTC_BUS_NUM) #define CONFIG_SYS_RTC_BUS_NUM 0 #endif -#if !defined(CONFIG_SYS_DTT_BUS_NUM) -#define CONFIG_SYS_DTT_BUS_NUM 0 -#endif #if !defined(CONFIG_SYS_SPD_BUS_NUM) #define CONFIG_SYS_SPD_BUS_NUM 0 #endif diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 93a4753732..1eef683ff0 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -383,7 +383,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_DTT CONFIG_CMD_ECCTEST CONFIG_CMD_EECONFIG CONFIG_CMD_EEPROM @@ -682,20 +681,6 @@ CONFIG_DRIVE_SATA CONFIG_DRIVE_TYPES CONFIG_DRIVE_USB CONFIG_DSP_CLUSTER_START -CONFIG_DTT -CONFIG_DTT_AD7414 -CONFIG_DTT_ADM1021 -CONFIG_DTT_DS1621 -CONFIG_DTT_DS1775 -CONFIG_DTT_DS620 -CONFIG_DTT_HYSTERESIS -CONFIG_DTT_LM63 -CONFIG_DTT_LM75 -CONFIG_DTT_MAX_TEMP -CONFIG_DTT_MIN_TEMP -CONFIG_DTT_PWM_LOOKUPTABLE -CONFIG_DTT_SENSORS -CONFIG_DTT_TACH_LIMIT CONFIG_DUOVERO CONFIG_DV_USBPHY_CTL CONFIG_DWC2_DFLT_SPEED_FULL @@ -3450,12 +3435,6 @@ CONFIG_SYS_DSPI_CTAR4 CONFIG_SYS_DSPI_CTAR5 CONFIG_SYS_DSPI_CTAR6 CONFIG_SYS_DSPI_CTAR7 -CONFIG_SYS_DTT_ADM1021 -CONFIG_SYS_DTT_BUS_NUM -CONFIG_SYS_DTT_HYSTERESIS -CONFIG_SYS_DTT_LOW_TEMP -CONFIG_SYS_DTT_MAX_TEMP -CONFIG_SYS_DTT_MIN_TEMP CONFIG_SYS_DUART_RST CONFIG_SYS_DV_CLKMODE CONFIG_SYS_DV_NOR_BOOT_CFG @@ -6115,7 +6094,6 @@ CONFIG_TIZEN CONFIG_TI_KEYSTONE_SERDES CONFIG_TI_KSNAV CONFIG_TI_SPI_MMAP -CONFIG_TMU_CMD_DTT CONFIG_TMU_TIMER CONFIG_TOTAL5200 CONFIG_TPL_DRIVERS_MISC_SUPPORT