From: Dmitry Korunov Date: Sun, 26 Nov 2017 09:38:53 +0000 (+0400) Subject: add support for Raspberry Pi Zero W X-Git-Tag: v2018.01-rc1~18 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=8993056fb3d4af4f0cd078df20130d4e7c35c2f7;p=u-boot add support for Raspberry Pi Zero W Signed-off-by: Dmitry Korunov --- diff --git a/arch/arm/dts/bcm2835-rpi-zero-w.dts b/arch/arm/dts/bcm2835-rpi-zero-w.dts new file mode 100644 index 0000000000..7817054775 --- /dev/null +++ b/arch/arm/dts/bcm2835-rpi-zero-w.dts @@ -0,0 +1,26 @@ +/dts-v1/; +#include "bcm2835.dtsi" +#include "bcm2835-rpi.dtsi" +#include "bcm283x-rpi-smsc9512.dtsi" +#include "bcm283x-rpi-usb-host.dtsi" + +/ { + compatible = "raspberrypi,model-zero-w", "brcm,bcm2835"; + model = "Raspberry Pi Zero W"; + + leds { + act { + gpios = <&gpio 47 0>; + }; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_gpio14>; + status = "okay"; +}; + +&hdmi { + hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; +}; diff --git a/arch/arm/mach-bcm283x/Kconfig b/arch/arm/mach-bcm283x/Kconfig index 69f7a4663c..a78239d63e 100644 --- a/arch/arm/mach-bcm283x/Kconfig +++ b/arch/arm/mach-bcm283x/Kconfig @@ -44,6 +44,22 @@ config TARGET_RPI This option creates a build targetting the ARM1176 ISA. select BCM2835 +config TARGET_RPI_0_W + bool "Raspberry Pi Zero W" + help + Support for all ARM1176-/BCM2835-based Raspberry Pi variants, such as + the RPi Zero model W. + + This option assumes the VideoCore firmware is configured to use the + mini UART (rather than PL011) for the serial console. This is the + default on the RPi Zero W. To enable the UART console, the following + non-default option must be present in config.txt: enable_uart=1. + This is required for U-Boot to operate correctly, even if you only + care about the HDMI/usbkbd console. + + This option creates a build targetting the ARMv7/AArch32 ISA. + select BCM2835 + config TARGET_RPI_2 bool "Raspberry Pi 2" help diff --git a/board/raspberrypi/rpi/rpi.c b/board/raspberrypi/rpi/rpi.c index 530f149617..3b7a54f519 100644 --- a/board/raspberrypi/rpi/rpi.c +++ b/board/raspberrypi/rpi/rpi.c @@ -105,6 +105,11 @@ static const struct rpi_model rpi_models_new_scheme[] = { DTB_DIR "bcm2835-rpi-zero.dtb", false, }, + [0xC] = { + "Zero W", + DTB_DIR "bcm2835-rpi-zero-w.dtb", + false, + }, }; static const struct rpi_model rpi_models_old_scheme[] = { diff --git a/configs/rpi_0_w_defconfig b/configs/rpi_0_w_defconfig new file mode 100644 index 0000000000..092f378f9f --- /dev/null +++ b/configs/rpi_0_w_defconfig @@ -0,0 +1,28 @@ +CONFIG_ARM=y +CONFIG_ARCH_BCM283X=y +CONFIG_TARGET_RPI_0_W=y +CONFIG_DEFAULT_DEVICE_TREE="bcm2835-rpi-zero-w" +CONFIG_DISTRO_DEFAULTS=y +CONFIG_OF_BOARD_SETUP=y +# CONFIG_DISPLAY_CPUINFO is not set +# CONFIG_DISPLAY_BOARDINFO is not set +CONFIG_SYS_PROMPT="U-Boot> " +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +# CONFIG_CMD_FPGA is not set +CONFIG_CMD_GPIO=y +CONFIG_DM_MMC=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_BCM2835=y +CONFIG_DM_ETH=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_STORAGE=y +CONFIG_USB_KEYBOARD=y +CONFIG_DM_VIDEO=y +CONFIG_SYS_WHITE_ON_BLACK=y +CONFIG_CONSOLE_SCROLL_LINES=10 +CONFIG_PHYS_TO_BUS=y +CONFIG_OF_LIBFDT_OVERLAY=y diff --git a/include/configs/rpi.h b/include/configs/rpi.h index c499b45b32..cab8661779 100644 --- a/include/configs/rpi.h +++ b/include/configs/rpi.h @@ -76,7 +76,7 @@ #endif /* Console UART */ -#ifdef CONFIG_BCM2837 +#if defined (CONFIG_BCM2837) || defined(CONFIG_TARGET_RPI_0_W) #define CONFIG_BCM283X_MU_SERIAL #else #define CONFIG_PL01X_SERIAL