From: Masahiro Yamada Date: Fri, 4 Apr 2014 06:25:08 +0000 (+0900) Subject: powerpc: remove rsdproto board support X-Git-Tag: v2014.07-rc1~35 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=8b043e6dc2e53743b0271debb6f506b95e788fd7;p=u-boot powerpc: remove rsdproto board support Enough time has passed since this board was moved to Orphan. Remove. - Remove board/rsdproto/* - Remove include/configs/rsdproto.h - Move the entry from boards.cfg to doc/README.scrapyard Signed-off-by: Masahiro Yamada --- diff --git a/board/rsdproto/Makefile b/board/rsdproto/Makefile deleted file mode 100644 index 9351e94e74..0000000000 --- a/board/rsdproto/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := rsdproto.o flash.o -obj-y += flash_asm.o diff --git a/board/rsdproto/flash.c b/board/rsdproto/flash.c deleted file mode 100644 index 37326d587a..0000000000 --- a/board/rsdproto/flash.c +++ /dev/null @@ -1,386 +0,0 @@ -/* - * (C) Copyright 2000 - * Marius Groeger - * Sysgo Real-Time Solutions, GmbH - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * Flash Routines for AM290[48]0B devices - * - *-------------------------------------------------------------------- - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - -/* flash hardware ids */ -#define VENDOR_AMD 0x0001 -#define AMD_29DL323C_B 0x2253 - -/* Define this to include autoselect sequence in flash_init(). Does NOT - * work when executing from flash itself, so this should be turned - * on only when debugging the RAM version. - */ -#undef WITH_AUTOSELECT - -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */ - -#if 1 -#define D(x) -#else -#define D(x) printf x -#endif - -/*----------------------------------------------------------------------- - * Functions - */ - -static unsigned char write_ull(flash_info_t *info, - unsigned long address, - volatile unsigned long long data); - -/* from flash_asm.S */ -extern void ull_write(unsigned long long volatile *address, - unsigned long long volatile *data); -extern void ull_read(unsigned long long volatile *address, - unsigned long long volatile *data); - -/*----------------------------------------------------------------------- - */ - -unsigned long flash_init (void) -{ - int i; - ulong addr; - -#ifdef WITH_AUTOSELECT - { - unsigned long long *f_addr = (unsigned long long *)PHYS_FLASH; - unsigned long long f_command, vendor, device; - /* Perform Autoselect */ - f_command = 0x00AA00AA00AA00AAULL; - ull_write(&f_addr[0x555], &f_command); - f_command = 0x0055005500550055ULL; - ull_write(&f_addr[0x2AA], &f_command); - f_command = 0x0090009000900090ULL; - ull_write(&f_addr[0x555], &f_command); - ull_read(&f_addr[0], &vendor); - vendor &= 0xffff; - ull_read(&f_addr[1], &device); - device &= 0xffff; - f_command = 0x00F000F000F000F0ULL; - ull_write(&f_addr[0x555], &f_command); - if (vendor != VENDOR_AMD || device != AMD_29DL323C_B) - return 0; - } -#endif - - /* Init: no FLASHes known */ - for (i=0; i= PHYS_FLASH - flash_protect(FLAG_PROTECT_SET, - CONFIG_SYS_MONITOR_BASE, - CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1, - &flash_info[0]); - flash_protect(FLAG_PROTECT_SET, - CONFIG_SYS_MONITOR_BASE, - CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1, - &flash_info[1]); -#endif - -#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR) -# ifndef CONFIG_ENV_SIZE -# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE -# endif - flash_protect(FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, - &flash_info[0]); - flash_protect(FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, - &flash_info[1]); -#endif - - return flash_info[0].size + flash_info[1].size; -} - -/*----------------------------------------------------------------------- - */ -void flash_print_info (flash_info_t *info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("missing or unknown FLASH type\n"); - return; - } - - switch (info->flash_id >> 16) { - case VENDOR_AMD: - printf ("AMD "); - break; - default: - printf ("Unknown Vendor "); - break; - } - - switch (info->flash_id & FLASH_TYPEMASK) { - case AMD_29DL323C_B: - printf ("AM29DL323CB (32 Mbit)\n"); - break; - default: - printf ("Unknown Chip Type\n"); - break; - } - - printf (" Size: %ld MB in %d Sectors\n", - info->size >> 20, info->sector_count); - - printf (" Sector Start Addresses:"); - for (i=0; isector_count; ++i) { - if ((i % 5) == 0) - printf ("\n "); - printf (" %08lX%s", - info->start[i], - info->protect[i] ? " (RO)" : " " - ); - } - printf ("\n"); - return; -} - -/*----------------------------------------------------------------------- - */ - -int flash_erase (flash_info_t *info, int s_first, int s_last) -{ - int flag, prot, sect, l_sect; - ulong start; - unsigned long long volatile *f_addr; - unsigned long long volatile f_command; - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf ("- missing\n"); - } else { - printf ("- no sectors to erase\n"); - } - return 1; - } - - prot = 0; - for (sect = s_first; sect <= s_last; sect++) { - if (info->protect[sect]) { - prot++; - } - } - if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", - prot); - } else { - printf ("\n"); - } - - f_addr = (unsigned long long *)info->start[0]; - f_command = 0x00AA00AA00AA00AAULL; - ull_write(&f_addr[0x555], &f_command); - f_command = 0x0055005500550055ULL; - ull_write(&f_addr[0x2AA], &f_command); - f_command = 0x0080008000800080ULL; - ull_write(&f_addr[0x555], &f_command); - f_command = 0x00AA00AA00AA00AAULL; - ull_write(&f_addr[0x555], &f_command); - f_command = 0x0055005500550055ULL; - ull_write(&f_addr[0x2AA], &f_command); - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - /* Start erase on unprotected sectors */ - for (l_sect = -1, sect = s_first; sect<=s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - - f_addr = - (unsigned long long *)(info->start[sect]); - f_command = 0x0030003000300030ULL; - ull_write(f_addr, &f_command); - l_sect = sect; - } - } - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - start = get_timer (0); - do - { - if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT) - { /* write reset command, command address is unimportant */ - /* this command turns the flash back to read mode */ - f_addr = - (unsigned long long *)(info->start[l_sect]); - f_command = 0x00F000F000F000F0ULL; - ull_write(f_addr, &f_command); - printf (" timeout\n"); - return 1; - } - } while(*f_addr != 0xFFFFFFFFFFFFFFFFULL); - - printf (" done\n"); - return 0; -} - -/*----------------------------------------------------------------------- - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ - -int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) -{ - unsigned long cp, wp; - unsigned long long data; - int i, l, rc; - - wp = (addr & ~7); /* get lower long long aligned address */ - - /* - * handle unaligned start bytes - */ - if ((l = addr - wp) != 0) { - data = 0; - for (i=0, cp=wp; i0; ++i) { - data = (data << 8) | *src++; - --cnt; - ++cp; - } - for (; cnt==0 && i<8; ++i, ++cp) { - data = (data << 8) | (*(uchar *)cp); - } - - if ((rc = write_ull(info, wp, data)) != 0) { - return rc; - } - wp += 4; - } - - /* - * handle long long aligned part - */ - while (cnt >= 8) { - data = 0; - for (i=0; i<8; ++i) { - data = (data << 8) | *src++; - } - if ((rc = write_ull(info, wp, data)) != 0) { - return rc; - } - wp += 8; - cnt -= 8; - } - - if (cnt == 0) { - return ERR_OK; - } - - /* - * handle unaligned tail bytes - */ - data = 0; - for (i=0, cp=wp; i<8 && cnt>0; ++i, ++cp) { - data = (data << 8) | *src++; - --cnt; - } - for (; i<8; ++i, ++cp) { - data = (data << 8) | (*(uchar *)cp); - } - - return write_ull(info, wp, data); -} - -/*--------------------------------------------------------------------------- -* -* FUNCTION NAME: write_ull -* -* DESCRIPTION: writes 8 bytes to flash -* -* EXTERNAL EFFECT: nothing -* -* PARAMETERS: 32 bit long pointer to address, 64 bit long pointer to data -* -* RETURNS: 0 if OK, 1 if timeout, 4 if parameter error -*--------------------------------------------------------------------------*/ - -static unsigned char write_ull(flash_info_t *info, - unsigned long address, - volatile unsigned long long data) -{ - static unsigned long long f_command; - static unsigned long long *f_addr; - ulong start; - - /* address muss be 8-aligned! */ - if (address & 0x7) - return ERR_ALIGN; - - f_addr = (unsigned long long *)info->start[0]; - f_command = 0x00AA00AA00AA00AAULL; - ull_write(&f_addr[0x555], &f_command); - f_command = 0x0055005500550055ULL; - ull_write(&f_addr[0x2AA], &f_command); - f_command = 0x00A000A000A000A0ULL; - ull_write(&f_addr[0x555], &f_command); - - f_addr = (unsigned long long *)address; - f_command = data; - ull_write(f_addr, &f_command); - - start = get_timer (0); - do - { - if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) - { - /* write reset command, command address is unimportant */ - /* this command turns the flash back to read mode */ - f_addr = (unsigned long long *)info->start[0]; - f_command = 0x00F000F000F000F0ULL; - ull_write(f_addr, &f_command); - return ERR_TIMOUT; - } - } while(*((unsigned long long *)address) != data); - - return 0; -} diff --git a/board/rsdproto/flash_asm.S b/board/rsdproto/flash_asm.S deleted file mode 100644 index 557cac0279..0000000000 --- a/board/rsdproto/flash_asm.S +++ /dev/null @@ -1,39 +0,0 @@ -/* - * -*- mode:c -*- - * - * (C) Copyright 2000 - * Marius Groeger - * Sysgo Real-Time Solutions, GmbH - * - * void ull_write(unsigned long long volatile *address, - * unsigned long long volatile *data) - * r3 = address - * r4 = data - * - * void ull_read(unsigned long long volatile *address, - * unsigned long long volatile *data) - * r3 = address - * r4 = data - * - * Uses the floating point unit to read and write 64 bit wide - * data (unsigned long long) on the 60x bus. This is necessary - * because all 4 flash chips use the /WE line from byte lane 0 - * - * IMPORTANT: data should always be 8-aligned, otherwise an exception will - * occur. - */ - -#include -#include - - .globl ull_write -ull_write: - lfd 0,0(r4) - stfd 0,0(r3) - blr - - .globl ull_read -ull_read: - lfd 0, 0(r3) - stfd 0, 0(r4) - blr diff --git a/board/rsdproto/rsdproto.c b/board/rsdproto/rsdproto.c deleted file mode 100644 index 1e85c2710d..0000000000 --- a/board/rsdproto/rsdproto.c +++ /dev/null @@ -1,361 +0,0 @@ -/* - * (C) Copyright 2000 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include - -/* define to initialise the SDRAM on the local bus */ -#undef INIT_LOCAL_BUS_SDRAM - -/* I2C Bus adresses for PPC & Protocol board */ -#define PPC8260_I2C_ADR 0x30 /*(0)011.0000 */ -#define LM84_PPC_I2C_ADR 0x2A /*(0)010.1010 */ -#define LM84_SHARC_I2C_ADR 0x29 /*(0)010.1001 */ -#define VIRTEX_I2C_ADR 0x25 /*(0)010.0101 */ -#define X24645_PPC_I2C_ADR 0x00 /*(0)00X.XXXX -> be careful ! No other i2c-chip should have an adress beginning with (0)00 !!! */ -#define RS5C372_PPC_I2C_ADR 0x32 /*(0)011.0010 -> this adress is programmed by the manufacturer and cannot be changed !!! */ - -/* - * I/O Port configuration table - * - * if conf is 1, then that port pin will be configured at boot time - * according to the five values podr/pdir/ppar/psor/pdat for that entry - */ - -const iop_conf_t iop_conf_tab[4][32] = { - - /* Port A configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PA31 */ { 0, 0, 0, 0, 0, 0 }, - /* PA30 */ { 0, 0, 0, 0, 0, 0 }, - /* PA29 */ { 0, 0, 0, 0, 0, 0 }, - /* PA28 */ { 0, 0, 0, 0, 0, 0 }, - /* PA27 */ { 0, 0, 0, 0, 0, 0 }, - /* PA26 */ { 0, 0, 0, 0, 0, 0 }, - /* PA25 */ { 0, 0, 0, 0, 0, 0 }, - /* PA24 */ { 0, 0, 0, 0, 0, 0 }, - /* PA23 */ { 0, 0, 0, 0, 0, 0 }, - /* PA22 */ { 0, 0, 0, 0, 0, 0 }, - /* PA21 */ { 0, 0, 0, 0, 0, 0 }, - /* PA20 */ { 0, 0, 0, 0, 0, 0 }, - /* PA19 */ { 0, 0, 0, 0, 0, 0 }, - /* PA18 */ { 0, 0, 0, 0, 0, 0 }, - /* PA17 */ { 0, 0, 0, 0, 0, 0 }, - /* PA16 */ { 0, 0, 0, 0, 0, 0 }, - /* PA15 */ { 0, 0, 0, 0, 0, 0 }, - /* PA14 */ { 0, 0, 0, 0, 0, 0 }, - /* PA13 */ { 0, 0, 0, 0, 0, 0 }, - /* PA12 */ { 0, 0, 0, 0, 0, 0 }, - /* PA11 */ { 0, 0, 0, 0, 0, 0 }, - /* PA10 */ { 0, 0, 0, 0, 0, 0 }, - /* PA9 */ { 0, 0, 0, 0, 0, 0 }, - /* PA8 */ { 0, 0, 0, 0, 0, 0 }, - /* PA7 */ { 0, 0, 0, 0, 0, 0 }, - /* PA6 */ { 0, 0, 0, 0, 0, 0 }, - /* PA5 */ { 0, 0, 0, 0, 0, 0 }, - /* PA4 */ { 0, 0, 0, 0, 0, 0 }, - /* PA3 */ { 0, 0, 0, 0, 0, 0 }, - /* PA2 */ { 0, 0, 0, 0, 0, 0 }, - /* PA1 */ { 0, 0, 0, 0, 0, 0 }, - /* PA0 */ { 0, 0, 0, 0, 0, 0 } - }, - - - { /* conf ppar psor pdir podr pdat */ - /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */ - /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */ - /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */ - /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */ - /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */ - /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */ - /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */ - /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */ - /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */ - /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */ - /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */ - /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */ - /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */ - /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */ - /* PB17 */ { 0, 0, 0, 0, 0, 0 }, - /* PB16 */ { 0, 0, 0, 0, 0, 0 }, - /* PB15 */ { 0, 0, 0, 0, 0, 0 }, - /* PB14 */ { 0, 0, 0, 0, 0, 0 }, - /* PB13 */ { 0, 0, 0, 0, 0, 0 }, - /* PB12 */ { 0, 0, 0, 0, 0, 0 }, - /* PB11 */ { 0, 0, 0, 0, 0, 0 }, - /* PB10 */ { 0, 0, 0, 0, 0, 0 }, - /* PB9 */ { 0, 0, 0, 0, 0, 0 }, - /* PB8 */ { 0, 0, 0, 0, 0, 0 }, - /* PB7 */ { 0, 0, 0, 0, 0, 0 }, - /* PB6 */ { 0, 0, 0, 0, 0, 0 }, - /* PB5 */ { 0, 0, 0, 0, 0, 0 }, - /* PB4 */ { 0, 0, 0, 0, 0, 0 }, - /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - }, - - - { /* conf ppar psor pdir podr pdat */ - /* PC31 */ { 0, 0, 0, 0, 0, 0 }, - /* PC30 */ { 0, 0, 0, 0, 0, 0 }, - /* PC29 */ { 0, 0, 0, 0, 0, 0 }, - /* PC28 */ { 0, 0, 0, 0, 0, 0 }, - /* PC27 */ { 0, 0, 0, 0, 0, 0 }, - /* PC26 */ { 0, 0, 0, 0, 0, 0 }, - /* PC25 */ { 0, 0, 0, 0, 0, 0 }, - /* PC24 */ { 0, 0, 0, 0, 0, 0 }, - /* PC23 */ { 0, 0, 0, 0, 0, 0 }, - /* PC22 */ { 0, 0, 0, 0, 0, 0 }, - /* PC21 */ { 0, 0, 0, 0, 0, 0 }, - /* PC20 */ { 0, 0, 0, 0, 0, 0 }, - /* PC19 */ { 1, 1, 0, 0, 0, 0 }, - /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* ETHRXCLK: CLK14 */ - /* PC17 */ { 0, 0, 0, 0, 0, 0 }, /* ETHTXCLK: CLK15 */ - /* PC16 */ { 0, 0, 0, 0, 0, 0 }, - /* PC15 */ { 0, 0, 0, 0, 0, 0 }, - /* PC14 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 UART CD/ */ - /* PC13 */ { 0, 0, 0, 0, 0, 0 }, - /* PC12 */ { 0, 0, 0, 0, 0, 0 }, - /* PC11 */ { 0, 0, 0, 0, 0, 0 }, - /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* ETHMDC: GP */ - /* PC9 */ { 1, 0, 0, 1, 0, 0 }, /* ETHMDIO: GP */ - /* PC8 */ { 0, 0, 0, 0, 0, 0 }, - /* PC7 */ { 0, 0, 0, 0, 0, 0 }, - /* PC6 */ { 0, 0, 0, 0, 0, 0 }, - /* PC5 */ { 0, 0, 0, 0, 0, 0 }, - /* PC4 */ { 0, 0, 0, 0, 0, 0 }, - /* PC3 */ { 0, 0, 0, 0, 0, 0 }, - /* PC2 */ { 0, 0, 0, 0, 0, 0 }, - /* PC1 */ { 0, 0, 0, 0, 0, 0 }, - /* PC0 */ { 0, 0, 0, 0, 0, 0 } - }, - - - { /* conf ppar psor pdir podr pdat */ - /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 UART RxD */ - /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 UART TxD */ - /* PD29 */ { 0, 0, 0, 0, 0, 0 }, - /* PD28 */ { 0, 0, 0, 0, 0, 0 }, - /* PD27 */ { 0, 0, 0, 0, 0, 0 }, - /* PD26 */ { 0, 0, 0, 0, 0, 0 }, - /* PD25 */ { 0, 0, 0, 0, 0, 0 }, - /* PD24 */ { 0, 0, 0, 0, 0, 0 }, - /* PD23 */ { 0, 0, 0, 0, 0, 0 }, - /* PD22 */ { 0, 0, 0, 0, 0, 0 }, - /* PD21 */ { 0, 0, 0, 0, 0, 0 }, - /* PD20 */ { 0, 0, 0, 0, 0, 0 }, - /* PD19 */ { 0, 0, 0, 0, 0, 0 }, - /* PD18 */ { 0, 0, 0, 0, 0, 0 }, - /* PD17 */ { 0, 0, 0, 0, 0, 0 }, - /* PD16 */ { 0, 0, 0, 0, 0, 0 }, - /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */ - /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */ - /* PD13 */ { 0, 0, 0, 0, 0, 0 }, - /* PD12 */ { 0, 0, 0, 0, 0, 0 }, - /* PD11 */ { 0, 0, 0, 0, 0, 0 }, - /* PD10 */ { 0, 0, 0, 0, 0, 0 }, - /* PD9 */ { 0, 0, 0, 0, 0, 0 }, - /* PD8 */ { 0, 0, 0, 0, 0, 0 }, - /* PD7 */ { 0, 0, 0, 0, 0, 0 }, - /* PD6 */ { 0, 0, 0, 0, 0, 0 }, - /* PD5 */ { 0, 0, 0, 0, 0, 0 }, - /* PD4 */ { 0, 0, 0, 0, 0, 0 }, - /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - } -}; - -/* ------------------------------------------------------------------------- */ - -struct tm { - unsigned int tm_sec; - unsigned int tm_min; - unsigned int tm_hour; - unsigned int tm_wday; - unsigned int tm_mday; - unsigned int tm_mon; - unsigned int tm_year; -}; - -void read_RS5C372_time (struct tm *timedate) -{ - unsigned char buffer[8]; - - if (! i2c_read (RS5C372_PPC_I2C_ADR, 0, 1, buffer, sizeof (buffer))) { - timedate->tm_sec = bcd2bin (buffer[0]); - timedate->tm_min = bcd2bin (buffer[1]); - timedate->tm_hour = bcd2bin (buffer[2]); - timedate->tm_wday = bcd2bin (buffer[3]); - timedate->tm_mday = bcd2bin (buffer[4]); - timedate->tm_mon = bcd2bin (buffer[5]); - timedate->tm_year = bcd2bin (buffer[6]) + 2000; - } else { - /*printf("i2c error %02x\n", rc); */ - memset (timedate, 0, sizeof (struct tm)); - } -} - -/* ------------------------------------------------------------------------- */ - -int read_LM84_temp (int address) -{ - unsigned char buffer[8]; - /*int rc;*/ - - if (! i2c_read (address, 0, 1, buffer, 1)) { - return (int) buffer[0]; - } else { - /*printf("i2c error %02x\n", rc); */ - return -42; - } -} - -/* ------------------------------------------------------------------------- */ - -/* - * Check Board Identity: - */ - -int checkboard (void) -{ - struct tm timedate; - unsigned int ppctemp, prottemp; - - puts ("Board: Rohde & Schwarz 8260 Protocol Board\n"); - - /* initialise i2c */ - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - - read_RS5C372_time (&timedate); - printf (" Time: %02d:%02d:%02d\n", - timedate.tm_hour, timedate.tm_min, timedate.tm_sec); - printf (" Date: %02d-%02d-%04d\n", - timedate.tm_mday, timedate.tm_mon, timedate.tm_year); - ppctemp = read_LM84_temp (LM84_PPC_I2C_ADR); - prottemp = read_LM84_temp (LM84_SHARC_I2C_ADR); - printf (" Temp: PPC %d C, Protocol Board %d C\n", - ppctemp, prottemp); - - return 0; -} - -/* ------------------------------------------------------------------------- */ - -/* - * Miscelaneous platform dependent initialisations while still - * running in flash - */ - -int misc_init_f (void) -{ - return 0; -} - -/* ------------------------------------------------------------------------- */ - -phys_size_t initdram (int board_type) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8260_t *memctl = &immap->im_memctl; - -#ifdef INIT_LOCAL_BUS_SDRAM - volatile uchar *ramaddr8; -#endif - volatile ulong *ramaddr32; - ulong sdmr; - int i; - - /* - * Only initialize SDRAM when running from FLASH. - * When running from RAM, don't touch it. - */ - if ((ulong) initdram & 0xff000000) { - immap->im_siu_conf.sc_ppc_acr = 0x02; - immap->im_siu_conf.sc_ppc_alrh = 0x01267893; - immap->im_siu_conf.sc_ppc_alrl = 0x89ABCDEF; - immap->im_siu_conf.sc_lcl_acr = 0x02; - immap->im_siu_conf.sc_lcl_alrh = 0x01234567; - immap->im_siu_conf.sc_lcl_alrl = 0x89ABCDEF; - /* - * Program local/60x bus Transfer Error Status and Control Regs: - * Disable parity errors - */ - immap->im_siu_conf.sc_tescr1 = 0x00040000; - immap->im_siu_conf.sc_ltescr1 = 0x00040000; - - /* - * Perform Power-Up Initialisation of SDRAM (see 8260 UM, 10.4.2) - * - * The appropriate BRx/ORx registers have already - * been set when we get here (see cpu_init_f). The - * SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE. - */ - memctl->memc_mptpr = 0x2000; - memctl->memc_mar = 0x0200; -#ifdef INIT_LOCAL_BUS_SDRAM - /* initialise local bus ram - * - * (using the PSRMR_ definitions is NOT an error here - * - the LSDMR has the same fields as the PSDMR!) - */ - memctl->memc_lsrt = 0x0b; - memctl->memc_lurt = 0x00; - ramaddr = (uchar *) PHYS_SDRAM_LOCAL; - sdmr = CONFIG_SYS_LSDMR & ~(PSDMR_OP_MSK | PSDMR_RFEN | PSDMR_PBI); - memctl->memc_lsdmr = sdmr | PSDMR_OP_PREA; - *ramaddr = 0xff; - for (i = 0; i < 8; i++) { - memctl->memc_lsdmr = sdmr | PSDMR_OP_CBRR; - *ramaddr = 0xff; - } - memctl->memc_lsdmr = sdmr | PSDMR_OP_MRW; - *ramaddr = 0xff; - memctl->memc_lsdmr = CONFIG_SYS_LSDMR | PSDMR_OP_NORM; -#endif - /* initialise 60x bus ram */ - memctl->memc_psrt = 0x0b; - memctl->memc_purt = 0x08; - ramaddr32 = (ulong *) PHYS_SDRAM_60X; - sdmr = CONFIG_SYS_PSDMR & ~(PSDMR_OP_MSK | PSDMR_RFEN | PSDMR_PBI); - memctl->memc_psdmr = sdmr | PSDMR_OP_PREA; - ramaddr32[0] = 0x00ff00ff; - ramaddr32[1] = 0x00ff00ff; - memctl->memc_psdmr = sdmr | PSDMR_OP_CBRR; - for (i = 0; i < 8; i++) { - ramaddr32[0] = 0x00ff00ff; - ramaddr32[1] = 0x00ff00ff; - } - memctl->memc_psdmr = sdmr | PSDMR_OP_MRW; - ramaddr32[0] = 0x00ff00ff; - ramaddr32[1] = 0x00ff00ff; - memctl->memc_psdmr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN; - } - - /* return the size of the 60x bus ram */ - return PHYS_SDRAM_60X_SIZE; -} - -/* ------------------------------------------------------------------------- */ - -/* - * Miscelaneous platform dependent initialisations after monitor - * has been relocated into ram - */ - -int misc_init_r (void) -{ - printf ("misc_init_r\n"); - return (0); -} diff --git a/board/rsdproto/u-boot.lds b/board/rsdproto/u-boot.lds deleted file mode 100644 index 44bcd19fb1..0000000000 --- a/board/rsdproto/u-boot.lds +++ /dev/null @@ -1,114 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc) -/* Do we need any of these for elf? - __DYNAMIC = 0; */ -SECTIONS -{ - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .interp : { *(.interp) } - .hash : { *(.hash) } - .dynsym : { *(.dynsym) } - .dynstr : { *(.dynstr) } - .rel.text : { *(.rel.text) } - .rela.text : { *(.rela.text) } - .rel.data : { *(.rel.data) } - .rela.data : { *(.rela.data) } - .rel.rodata : { *(.rel.rodata) } - .rela.rodata : { *(.rela.rodata) } - .rel.got : { *(.rel.got) } - .rela.got : { *(.rela.got) } - .rel.ctors : { *(.rel.ctors) } - .rela.ctors : { *(.rela.ctors) } - .rel.dtors : { *(.rel.dtors) } - .rela.dtors : { *(.rela.dtors) } - .rel.bss : { *(.rel.bss) } - .rela.bss : { *(.rela.bss) } - .rel.plt : { *(.rel.plt) } - .rela.plt : { *(.rela.plt) } - .init : { *(.init) } - .plt : { *(.plt) } - .text : - { - arch/powerpc/cpu/mpc8260/start.o (.text) - *(.text) - *(.got1) - /*. = env_offset; */ - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(.eh_frame) - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - .fini : { *(.fini) } =0 - .ctors : { *(.ctors) } - .dtors : { *(.dtors) } - - /* Read-write section, merged into data segment: */ - . = (. + 0x0FFF) & 0xFFFFF000; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - _GOT2_TABLE_ = .; - KEEP(*(.got2)) - KEEP(*(.got)) - PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4); - _FIXUP_TABLE_ = .; - KEEP(*(.fixup)) - } - __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1; - __fixup_entries = (. - _FIXUP_TABLE_)>>2; - - .data : - { - *(.data) - *(.data1) - *(.sdata) - *(.sdata2) - *(.dynamic) - CONSTRUCTORS - } - _edata = .; - PROVIDE (edata = .); - - . = .; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(4096); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(4096); - __init_end = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.sbss) *(.scommon) - *(.dynbss) - *(.bss) - *(COMMON) - . = ALIGN(4); - } - __bss_end = . ; - PROVIDE (end = .); -} diff --git a/boards.cfg b/boards.cfg index d90091708b..d0df823a14 100644 --- a/boards.cfg +++ b/boards.cfg @@ -1244,4 +1244,3 @@ Orphan arm arm1136 mx31 freescale - Orphan arm pxa - - - lubbock - (dead address) Kyle Harris Orphan powerpc 74xx_7xx - - evb64260 EVB64260 - - Orphan powerpc mpc824x - - mousse MOUSSE - - -Orphan powerpc mpc8260 - - - rsdproto - - diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 125ba809c9..adcf163a81 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -11,6 +11,7 @@ easily if here is something they might want to dig for... Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +rsdproto powerpc mpc8260 - 2014-04-04 RPXsuper powerpc mpc8260 - 2014-04-04 RPXClassic powerpc mpc8xx - 2014-04-04 RPXlite powerpc mpc8xx - 2014-04-04 diff --git a/include/configs/rsdproto.h b/include/configs/rsdproto.h deleted file mode 100644 index 06211380d4..0000000000 --- a/include/configs/rsdproto.h +++ /dev/null @@ -1,400 +0,0 @@ -/* - * (C) Copyright 2000 - * Murray Jensen - * - * (C) Copyright 2000 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * Configuation settings for the R&S Protocol Board board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_RSD_PROTO 1 /* on a R&S Protocol Board */ -#define CONFIG_CPM2 1 /* Has a CPM2 */ - -#define CONFIG_SYS_TEXT_BASE 0xff000000 -#define CONFIG_SYS_LDSCRIPT "board/rsdproto/u-boot.lds" - -#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ - -/* - * select serial console configuration - * - * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - * - * if CONFIG_CONS_NONE is defined, then the serial console routines must - * defined elsewhere. - */ -#undef CONFIG_CONS_ON_SMC /* define if console on SMC */ -#define CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on neither */ -#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ - -/* - * select ethernet configuration - * - * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then - * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 - * for FCC) - * - * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be - * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. - */ -#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */ -#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */ -#undef CONFIG_ETHER_NONE /* define if ethernet on neither */ -#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ - -#if (CONFIG_ETHER_INDEX == 2) - -/* - * - Rx-CLK is CLK13 - * - Tx-CLK is CLK14 - * - Select bus for bd/buffers (see 28-13) - * - Enable Full Duplex in FSMR - */ -# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) -# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) -# define CONFIG_SYS_CPMFCR_RAMTYPE (0) -# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) - -#endif /* CONFIG_ETHER_INDEX */ - - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* enable I2C */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x30 - - -/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ -#define CONFIG_8260_CLKIN 50000000 /* in Hz */ - -#define CONFIG_BAUDRATE 115200 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#undef CONFIG_CMD_KGDB - - -/* Define this if you want to boot from 0x00000100. If you don't define - * this, you will need to program the bootloader to 0xfff00000, and - * get the hardware reset config words at 0xfe000000. The simplest - * way to do that is to program the bootloader at both addresses. - * It is suggested that you just let U-Boot live at 0x00000000. - */ -#define CONFIG_SYS_RSD_BOOT_LOW 1 - -#define CONFIG_BOOTDELAY 5 -#define CONFIG_BOOTARGS "devfs=mount root=ramfs" -#define CONFIG_ETHADDR 08:00:3e:26:0a:5a -#define CONFIG_NETMASK 255.255.0.0 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x01c00000 /* 4 ... 28 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define PHYS_SDRAM_60X 0x00000000 /* SDRAM (60x Bus) */ -#define PHYS_SDRAM_60X_SIZE 0x08000000 /* 128 MB */ - -#define PHYS_SDRAM_LOCAL 0x40000000 /* SDRAM (Local Bus) */ -#define PHYS_SDRAM_LOCAL_SIZE 0x04000000 /* 64 MB */ - -#define PHYS_DPRAM_PCI 0xE8000000 /* DPRAM PPC/PCI */ -#define PHYS_DPRAM_PCI_SIZE 0x00020000 /* 128 KB */ - -/*#define PHYS_DPRAM_PCI_SEM 0x04020000 / * DPRAM PPC/PCI Semaphore */ -/*#define PHYS_DPRAM_PCI_SEM_SIZE 0x00000001 / * 1 Byte */ - -#define PHYS_DPRAM_SHARC 0xE8100000 /* DPRAM PPC/Sharc */ -#define PHYS_DPRAM_SHARC_SIZE 0x00040000 /* 256 KB */ - -/*#define PHYS_DPRAM_SHARC_SEM 0x04140000 / * DPRAM PPC/Sharc Semaphore */ -/*#define PHYS_DPRAM_SHARC_SEM_SIZE 0x00000001 / * 1 Byte */ - -#define PHYS_VIRTEX_REGISTER 0xE8300000 /* FPGA implemented register */ -#define PHYS_VIRTEX_REGISTER_SIZE 0x00000100 - -#define PHYS_USB 0x04200000 /* USB Controller (60x Bus) */ -#define PHYS_USB_SIZE 0x00000002 /* 2 Bytes */ - -#define PHYS_IMMR 0xF0000000 /* Internal Memory Mapped Reg. */ - -#define PHYS_FLASH 0xFF000000 /* Flash (60x Bus) */ -#define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */ - -#define CONFIG_SYS_IMMR PHYS_IMMR - -/*----------------------------------------------------------------------- - * Reset Address - * - * In order to reset the CPU, U-Boot jumps to a special address which - * causes a machine check exception. The default address for this is - * CONFIG_SYS_MONITOR_BASE - sizeof (ulong), which might not always work, eg. when - * testing the monitor in RAM using a JTAG debugger. - * - * Just set CONFIG_SYS_RESET_ADDRESS to an address that you know is sure to - * cause a bus error on your hardware. - */ -#define CONFIG_SYS_RESET_ADDRESS 0x20000000 - -/*----------------------------------------------------------------------- - * Hard Reset Configuration Words - */ - -#if defined(CONFIG_SYS_RSD_BOOT_LOW) -# define CONFIG_SYS_RSD_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) -#else -# define CONFIG_SYS_RSD_HRCW_BOOT_FLAGS (0) -#endif /* defined(CONFIG_SYS_RSD_BOOT_LOW) */ - -/* get the HRCW ISB field from CONFIG_SYS_IMMR */ -#define CONFIG_SYS_RSD_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) |\ - ((CONFIG_SYS_IMMR & 0x01000000) >> 7) |\ - ((CONFIG_SYS_IMMR & 0x00100000) >> 4) ) - -#define CONFIG_SYS_HRCW_MASTER (HRCW_L2CPC10 | \ - HRCW_DPPC11 | \ - CONFIG_SYS_RSD_HRCW_IMMR |\ - HRCW_MMR00 | \ - HRCW_APPC10 | \ - HRCW_CS10PC00 | \ - HRCW_MODCK_H0000 |\ - CONFIG_SYS_RSD_HRCW_BOOT_FLAGS) - -/* no slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependend. - */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_60X -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH -/*#define CONFIG_SYS_MONITOR_BASE 0x200000 */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_RAMBOOT -#endif -#define CONFIG_SYS_MONITOR_LEN (160 << 10) /* Reserve 160 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 63 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 12000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 3000 /* Timeout for Flash Write (in ms) */ - -/* turn off NVRAM env feature */ -#undef CONFIG_NVRAM_ENV - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (PHYS_FLASH + 0x28000) /* Addr of Environment Sector */ -#define CONFIG_ENV_SECT_SIZE 0x8000 /* Total Size of Environment Sector */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * HIDx - Hardware Implementation-dependent Registers 2-11 - *----------------------------------------------------------------------- - * HID0 also contains cache control - initially enable both caches and - * invalidate contents, then the final state leaves only the instruction - * cache enabled. Note that Power-On and Hard reset invalidate the caches, - * but Soft reset does not. - * - * HID1 has only read-only information - nothing to set. - */ -#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|HID0_IFEM|HID0_ABE) -#define CONFIG_SYS_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE|HID0_EMCP) -#define CONFIG_SYS_HID2 0 - -/*----------------------------------------------------------------------- - * RMR - Reset Mode Register - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RMR 0 - -/*----------------------------------------------------------------------- - * BCR - Bus Configuration 4-25 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_BCR 0x100c0000 - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 4-31 - *----------------------------------------------------------------------- - */ - -#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC11 | SIUMCR_L2CPC10 | SIUMCR_APPC10 | \ - SIUMCR_CS10PC01 | SIUMCR_BCTLC01) - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable - */ -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_PBME | SYPCR_LBME | \ - SYPCR_SWRI | SYPCR_SWP) - -/*----------------------------------------------------------------------- - * TMCNTSC - Time Counter Status and Control 4-40 - *----------------------------------------------------------------------- - * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, - * and enable Time Counter - */ -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC | TMCNTSC_ALR | TMCNTSC_TCF | TMCNTSC_TCE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 4-42 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable - * Periodic timer - */ -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) - -/*----------------------------------------------------------------------- - * SCCR - System Clock Control 9-8 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_SCCR 0x00000000 - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration 13-7 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0 - -/* - * Init Memory Controller: - */ - -#define CONFIG_SYS_PSDMR 0x494D2452 -#define CONFIG_SYS_LSDMR 0x49492552 - -/* Flash */ -#define CONFIG_SYS_BR0_PRELIM (PHYS_FLASH | BRx_V) -#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(PHYS_FLASH_SIZE) | \ - ORxG_BCTLD | \ - ORxG_SCY_5_CLK) - -/* DPRAM to the PCI BUS on the protocol board */ -#define CONFIG_SYS_BR1_PRELIM (PHYS_DPRAM_PCI | BRx_V) -#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(PHYS_DPRAM_PCI_SIZE) | \ - ORxG_ACS_DIV4) - -/* 60x Bus SDRAM */ -#define CONFIG_SYS_BR2_PRELIM (PHYS_SDRAM_60X | BRx_MS_SDRAM_P | BRx_V) -#define CONFIG_SYS_OR2_PRELIM (ORxS_SIZE_TO_AM(PHYS_SDRAM_60X_SIZE) | \ - ORxS_BPD_4 | \ - ORxS_ROWST_PBI1_A2 | \ - ORxS_NUMR_13 | \ - ORxS_IBID) - -/* Virtex-FPGA - Register */ -#define CONFIG_SYS_BR3_PRELIM (PHYS_VIRTEX_REGISTER | BRx_V) -#define CONFIG_SYS_OR3_PRELIM (ORxS_SIZE_TO_AM(PHYS_VIRTEX_REGISTER_SIZE) | \ - ORxG_SCY_1_CLK | \ - ORxG_ACS_DIV2 | \ - ORxG_CSNT ) - -/* local bus SDRAM */ -#define CONFIG_SYS_BR4_PRELIM (PHYS_SDRAM_LOCAL | BRx_PS_32 | BRx_MS_SDRAM_L | BRx_V) -#define CONFIG_SYS_OR4_PRELIM (ORxS_SIZE_TO_AM(PHYS_SDRAM_LOCAL_SIZE) | \ - ORxS_BPD_4 | \ - ORxS_ROWST_PBI1_A4 | \ - ORxS_NUMR_13) - -/* DPRAM to the Sharc-Bus on the protocol board */ -#define CONFIG_SYS_BR5_PRELIM (PHYS_DPRAM_SHARC | BRx_V) -#define CONFIG_SYS_OR5_PRELIM (P2SZ_TO_AM(PHYS_DPRAM_SHARC_SIZE) | \ - ORxG_ACS_DIV4) - -#endif /* __CONFIG_H */