From: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Date: Thu, 25 May 2017 08:55:55 +0000 (+0530)
Subject: nand: zynq: Add support for 16-bit buswidth
X-Git-Tag: v2018.07-rc1~159^2~21
X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=9ca8388059de8f10e035fbdcaa418ec3caeb0599;p=u-boot

nand: zynq: Add support for 16-bit buswidth

This patch adds support for 16-bit buswidth by determining
the bus width based on mio configuration.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---

diff --git a/drivers/mtd/nand/zynq_nand.c b/drivers/mtd/nand/zynq_nand.c
index efd3c9b798..4d0ea9e6b9 100644
--- a/drivers/mtd/nand/zynq_nand.c
+++ b/drivers/mtd/nand/zynq_nand.c
@@ -16,6 +16,7 @@
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/nand_ecc.h>
 #include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
 
 /* The NAND flash driver defines */
 #define ZYNQ_NAND_CMD_PHASE		1
@@ -83,6 +84,15 @@
 #define ZYNQ_NAND_ECC_BUSY	(1 << 6)	/* ECC block is busy */
 #define ZYNQ_NAND_ECC_MASK	0x00FFFFFF	/* ECC value mask */
 
+#define ZYNQ_NAND_MIO_NUM_NAND_8BIT	13
+#define ZYNQ_NAND_MIO_NUM_NAND_16BIT	8
+
+enum zynq_nand_bus_width {
+	NAND_BW_UNKNOWN = -1,
+	NAND_BW_8BIT,
+	NAND_BW_16BIT,
+};
+
 #ifndef NAND_CMD_LOCK_TIGHT
 #define NAND_CMD_LOCK_TIGHT 0x2c
 #endif
@@ -1005,6 +1015,23 @@ static int zynq_nand_device_ready(struct mtd_info *mtd)
 	return 0;
 }
 
+static int zynq_nand_check_is_16bit_bw_flash(void)
+{
+	int is_16bit_bw = NAND_BW_UNKNOWN;
+	int mio_num_8bit = 0, mio_num_16bit = 0;
+
+	mio_num_8bit = zynq_slcr_get_mio_pin_status("nand8");
+	if (mio_num_8bit == ZYNQ_NAND_MIO_NUM_NAND_8BIT)
+		is_16bit_bw = NAND_BW_8BIT;
+
+	mio_num_16bit = zynq_slcr_get_mio_pin_status("nand16");
+	if (mio_num_8bit == ZYNQ_NAND_MIO_NUM_NAND_8BIT &&
+	    mio_num_16bit == ZYNQ_NAND_MIO_NUM_NAND_16BIT)
+		is_16bit_bw = NAND_BW_16BIT;
+
+	return is_16bit_bw;
+}
+
 static int zynq_nand_init(struct nand_chip *nand_chip, int devnum)
 {
 	struct zynq_nand_info *xnand;
@@ -1016,6 +1043,7 @@ static int zynq_nand_init(struct nand_chip *nand_chip, int devnum)
 	unsigned long ecc_cfg;
 	int ondie_ecc_enabled = 0;
 	int err = -1;
+	int is_16bit_bw;
 
 	xnand = calloc(1, sizeof(struct zynq_nand_info));
 	if (!xnand) {
@@ -1045,6 +1073,16 @@ static int zynq_nand_init(struct nand_chip *nand_chip, int devnum)
 	nand_chip->read_buf = zynq_nand_read_buf;
 	nand_chip->write_buf = zynq_nand_write_buf;
 
+	is_16bit_bw = zynq_nand_check_is_16bit_bw_flash();
+	if (is_16bit_bw == NAND_BW_UNKNOWN) {
+		printf("%s: Unable detect NAND based on MIO settings\n",
+		       __func__);
+		goto fail;
+	}
+
+	if (is_16bit_bw == NAND_BW_16BIT)
+		nand_chip->options = NAND_BUSWIDTH_16;
+
 	nand_chip->bbt_options = NAND_BBT_USE_FLASH;
 
 	/* Initialize the NAND flash interface on NAND controller */