From: Markus Klotzbücher Date: Wed, 8 Feb 2006 17:56:28 +0000 (+0100) Subject: Changes: X-Git-Tag: LABEL_2006_03_12_0025~39 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=9d803d8c;p=u-boot Changes: * lots of bugfixes in the assembler code * reverted hardware.h back to original * enabled hardware DRAM calibration * GCC-4 fix: modified GLOBAL_DATA_POINTER macro --- diff --git a/board/zylonite/lowlevel_init.S b/board/zylonite/lowlevel_init.S index 54c2adfaf3..4d62be5d5e 100644 --- a/board/zylonite/lowlevel_init.S +++ b/board/zylonite/lowlevel_init.S @@ -39,6 +39,16 @@ DRAM_SIZE: .long CFG_DRAM_SIZE .endm +.macro wait time + ldr r2, =OSCR + mov r3, #0 + str r3, [r2] +0: + ldr r3, [r2] + cmp r3, \time + bls 0b +.endm + /* * Memory setup */ @@ -48,7 +58,7 @@ lowlevel_init: /* Set up GPIO pins first ----------------------------------------- */ mov r10, lr - /* GPIO41, 42, 43, 44, 45, 46, 47, 48 */ + /* Configure GPIO Pins 41 - 48 as UART1 / altern. Fkt. 2 */ ldr r0, =0x40E10438 @ GPIO41 FFRXD ldr r1, =0x802 str r1, [r0] @@ -82,7 +92,7 @@ lowlevel_init: str r1, [r0] /* tebrandt - ASCR, clear the RDH bit */ - ldr r0, =ASCR + ldr r0, =ASCR ldr r1, [r0] bic r1, r1, #0x80000000 str r1, [r0] @@ -101,16 +111,18 @@ lowlevel_init: /* FIXME: can be optimized later */ /* ---------------------------------------------------------------- */ - ldr r3, =OSCR /* reset the OS Timer Count to zero */ - mov r2, #0 - str r2, [r3] - ldr r4, =0x300 /* really 0x2E1 is about 200usec, */ - /* so 0x300 should be plenty */ -1: - ldr r2, [r3] - cmp r4, r2 - bgt 1b - + /* mk: replaced with wait macro */ +/* ldr r3, =OSCR /\* reset the OS Timer Count to zero *\/ */ +/* mov r2, #0 */ +/* str r2, [r3] */ +/* ldr r4, =0x300 /\* really 0x2E1 is about 200usec, *\/ */ +/* /\* so 0x300 should be plenty *\/ */ +/* 1: */ +/* ldr r2, [r3] */ +/* cmp r4, r2 */ +/* bgt 1b */ + wait #300 + mem_init: /* configure the MEMCLKCFG register */ @@ -209,8 +221,12 @@ mem_init: str r2, [r1] ldr r2, [r1] - /* DDR Read-Strobe Delay Calibration */ - /* bl ddr_calibration */ + /* Hardware DDR Read-Strobe Delay Calibration */ + ldr r0, =DDR_HCAL @ DDR_HCAL + ldr r1, =0x803ffc07 @ the offset is correct? -SC + str r1, [r0] + wait #5 + ldr r1, [r0] /* Here we assume the hardware calibration alwasy be successful. -SC */ /* Set DMCEN bit in MDCNFG Register */ @@ -220,10 +236,12 @@ mem_init: str r1, [r0] /* scrub/init SDRAM if enabled/present */ - ldr r11, =0xa0000000 //RAM_BASE // base address of SDRAM - ldr r12, =0x04000000 // size of memory to scrub - mov r8,r12 // save DRAM size - mov r0, #0 // scrub with 0x0000:0000 +/* ldr r11, =0xa0000000 /\* base address of SDRAM (CFG_DRAM_BASE) *\/ */ +/* ldr r12, =0x04000000 /\* size of memory to scrub (CFG_DRAM_SIZE) *\/ */ +/* mov r8,r12 /\* save DRAM size (mk: why???) *\/ */ + ldr r8, =0xa0000000 /* base address of SDRAM (CFG_DRAM_BASE) */ + ldr r9, =0x04000000 /* size of memory to scrub (CFG_DRAM_SIZE) */ + mov r0, #0 /* scrub with 0x0000:0000 */ mov r1, #0 mov r2, #0 mov r3, #0 @@ -232,8 +250,8 @@ mem_init: mov r6, #0 mov r7, #0 10: /* fastScrubLoop */ - subs r12, r12, #32 // 32 bytes/line - stmia r11!, {r0-r7} + subs r9, r9, #32 // 32 bytes/line + stmia r8!, {r0-r7} beq 15f b 10b @@ -264,3 +282,94 @@ mem_init: endlowlevel_init: mov pc, lr + + +/* +@******************************************************************************** +@ DDR calibration +@ +@ This function is used to calibrate DQS delay lines. +@ Monahans supports three ways to do it. One is software +@ calibration. Two is hardware calibration. Three is hybrid +@ calibration. +@ +@ TBD +@ -SC +ddr_calibration: + + @ Case 1: Write the correct delay value once + @ Configure DDR_SCAL Register + ldr r0, =DDR_SCAL @ DDR_SCAL +q ldr r1, =0xaf2f2f2f + str r1, [r0] + ldr r1, [r0] +*/ +/* @ Case 2: Software Calibration + @ Write test pattern to memory + ldr r5, =0x0faf0faf @ Data Pattern + ldr r4, =0xa0000000 @ DDR ram + str r5, [r4] + + mov r1, =0x0 @ delay count + mov r6, =0x0 + mov r7, =0x0 +ddr_loop1: + add r1, r1, =0x1 + cmp r1, =0xf + ble end_loop + mov r3, r1 + mov r0, r1, lsl #30 + orr r3, r3, r0 + mov r0, r1, lsl #22 + orr r3, r3, r0 + mov r0, r1, lsl #14 + orr r3, r3, r0 + orr r3, r3, =0x80000000 + ldr r2, =DDR_SCAL + str r3, [r2] + + ldr r2, [r4] + cmp r2, r5 + bne ddr_loop1 + mov r6, r1 +ddr_loop2: + add r1, r1, =0x1 + cmp r1, =0xf + ble end_loop + mov r3, r1 + mov r0, r1, lsl #30 + orr r3, r3, r0 + mov r0, r1, lsl #22 + orr r3, r3, r0 + mov r0, r1, lsl #14 + orr r3, r3, r0 + orr r3, r3, =0x80000000 + ldr r2, =DDR_SCAL + str r3, [r2] + + ldr r2, [r4] + cmp r2, r5 + be ddr_loop2 + mov r7, r2 + + add r3, r6, r7 + lsr r3, r3, =0x1 + mov r0, r1, lsl #30 + orr r3, r3, r0 + mov r0, r1, lsl #22 + orr r3, r3, r0 + mov r0, r1, lsl #14 + orr r3, r3, r0 + orr r3, r3, =0x80000000 + ldr r2, =DDR_SCAL + +end_loop: + + @ Case 3: Hardware Calibratoin + ldr r0, =DDR_HCAL @ DDR_HCAL + ldr r1, =0x803ffc07 @ the offset is correct? -SC + str r1, [r0] + wait #5 + ldr r1, [r0] + mov pc, lr +*/ diff --git a/include/asm-arm/arch-pxa/hardware.h b/include/asm-arm/arch-pxa/hardware.h index a12aea14c4..c8c479a186 100644 --- a/include/asm-arm/arch-pxa/hardware.h +++ b/include/asm-arm/arch-pxa/hardware.h @@ -8,6 +8,11 @@ * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. + * + * Note: This file was taken from linux-2.4.19-rmk4-pxa1 + * + * - 2003/01/20 implementation specifics activated + * Robert Schwebel */ #ifndef __ASM_ARCH_HARDWARE_H @@ -16,6 +21,16 @@ #include #include + +/* + * These are statically mapped PCMCIA IO space for designs using it as a + * generic IO bus, typically with ISA parts, hardwired IDE interfaces, etc. + * The actual PCMCIA code is mapping required IO region at run time. + */ +#define PCMCIA_IO_0_BASE 0xf6000000 +#define PCMCIA_IO_1_BASE 0xf7000000 + + /* * We requires absolute addresses. */ @@ -29,63 +44,22 @@ #define UNCACHED_ADDR UNCACHED_PHYS_0 /* - * Intel PXA2xx internal register mapping: + * Intel PXA internal I/O mappings: * - * 0x40000000 - 0x41ffffff <--> 0xf2000000 - 0xf3ffffff - * 0x44000000 - 0x45ffffff <--> 0xf4000000 - 0xf5ffffff - * 0x48000000 - 0x49ffffff <--> 0xf6000000 - 0xf7ffffff - * 0x4c000000 - 0x4dffffff <--> 0xf8000000 - 0xf9ffffff - * 0x50000000 - 0x51ffffff <--> 0xfa000000 - 0xfbffffff - * 0x54000000 - 0x55ffffff <--> 0xfc000000 - 0xfdffffff - * 0x58000000 - 0x59ffffff <--> 0xfe000000 - 0xffffffff - * - * Note that not all PXA2xx chips implement all those addresses, and the - * kernel only maps the minimum needed range of this mapping. - */ -#ifndef CONFIG_CPU_MONAHANS -#define io_p2v(x) (0xf2000000 + ((x) & 0x01ffffff) + (((x) & 0x1c000000) >> 1)) -#define io_v2p(x) (0x3c000000 + ((x) & 0x01ffffff) + (((x) & 0x0e000000) << 1)) -#else - -/* There are too many IO area needed to map, so I divide them into 3 areas - * 0x40000000 - 0x41ffffff <--> 0xf6000000 - 0xf7ffffff Devs + * 0x40000000 - 0x41ffffff <--> 0xf8000000 - 0xf9ffffff + * 0x44000000 - 0x45ffffff <--> 0xfa000000 - 0xfbffffff + * 0x48000000 - 0x49ffffff <--> 0xfc000000 - 0xfdffffff */ -#define io_p2v(x) ((((x) & 0xfc000000)>>4) + 0xf2000000 + ((x)&0x01ffffff)) -#define io_v2p(x) (((((x) - 0xf2000000)&0xfc000000)<<4) + ((x)&0x01ffffff)) -/* - * 0x42000000 - 0x421fffff <--> 0xf8000000 - 0xf81fffff MMC2 & USIM2 - * 0x43000000 - 0x430fffff <--> 0xf8200000 - 0xf82fffff Caddo - * 0x43100000 - 0x431fffff <--> 0xf8300000 - 0xf83fffff NAND - * 0x44000000 - 0x440fffff <--> 0xf8400000 - 0xf84fffff LCD - * 0x46000000 - 0x460fffff <--> 0xf8800000 - 0xf88fffff Mini LCD - * 0x48100000 - 0x481fffff <--> 0xf8d00000 - 0xf8dfffff Dynamic Mem Ctl - * 0x4a000000 - 0x4a0fffff <--> 0xf9000000 - 0xf90fffff Static Mem Ctl - * 0x4c000000 - 0x4c0fffff <--> 0xf9400000 - 0xf94fffff USB Host - */ - -#define io_p2v_2(x) (((((x) - 0x42000000) & 0xff000000) >> 3) + 0xf8000000\ - + ((x) & 0x001fffff)) -#define io_v2p_2(x) (((((x) & 0xffe00000) - 0xf8000000) << 3) + 0x42000000\ - + (x & 0x001fffff)) -/* - * 0x50000000 - 0x500fffff <--> 0xfa000000 - 0xfa0fffff Camera Interface - * 0x54000000 - 0x540fffff <--> 0xfa400000 - 0xfa4fffff 2D Graphics Ctrl - * 0x54100000 - 0x541fffff <--> 0xfa500000 - 0xfa5fffff USB Device 2.0 Ctrl - * 0x58000000 - 0x580fffff <--> 0xfa800000 - 0xfa8fffff Internal SRAM Ctrl - */ - -#define io_p2v_3(x) ((((x) & 0xfc000000) >> 4) + 0xf5000000 + \ - ((x) & 0x001fffff)) -#define io_v2p_3(x) (((((x) - 0xf5000000) & 0x0fc00000) << 4) + \ - ((x) & 0x001fffff)) -#endif /* CONFIG_CPU_MONAHANS */ +/* FIXME: Only this does work for u-boot... find out why... [RS] */ +#define UBOOT_REG_FIX 1 +#ifndef UBOOT_REG_FIX #ifndef __ASSEMBLY__ -#if 0 -# define __REG(x) (*((volatile u32 *)io_p2v(x))) -#else +#define io_p2v(x) ( ((x) | 0xbe000000) ^ (~((x) >> 1) & 0x06000000) ) +#define io_v2p( x ) ( ((x) & 0x41ffffff) ^ ( ((x) & 0x06000000) << 1) ) + /* * This __REG() version gives the same results as the one above, except * that we are fooling gcc somehow so it generates far better and smaller @@ -96,56 +70,66 @@ typedef struct { volatile u32 offset[4096]; } __regbase; # define __REGP(x) ((__regbase *)((x)&~4095))->offset[((x)&4095)>>2] # define __REG(x) __REGP(io_p2v(x)) +#endif -/* __REG_2 is for NAND, LCD etc. - * __REG_3 is for Camera Interface, 2D Graphics, U2D etc.*/ -#ifdef CONFIG_CPU_MONAHANS -#define __REG_2(x) __REGP(io_p2v_2(x)) -#define __REG_3(x) __REGP(io_p2v_3(x)) - -#endif /* CONFIG_CPU_MONAHANS */ -#endif /* if 0 */ - -/* With indexed regs we don't want to feed the index through io_p2v() - especially if it is a variable, otherwise horrible code will result. */ -# define __REG2(x,y) (*(volatile u32 *)((u32)&__REG(x) + (y))) +/* Let's kick gcc's ass again... */ +# define __REG2(x,y) \ + ( __builtin_constant_p(y) ? (__REG((x) + (y))) \ + : (*(volatile u32 *)((u32)&__REG(x) + (y))) ) # define __PREG(x) (io_v2p((u32)&(x))) -#else /* ifndef __ASSEMBLY__ */ +#else # define __REG(x) io_p2v(x) # define __PREG(x) io_v2p(x) -#ifdef CONFIG_CPU_MONAHANS -# define __REG_2(x) io_p2v(x) -# define __REG_3(x) io_p2v(x) -#endif /* CONFIG_CPU_MONAHANS */ +# undef io_p2v +# undef __REG +# ifndef __ASSEMBLY__ +# define io_p2v(PhAdd) (PhAdd) +# define __REG(x) (*((volatile u32 *)io_p2v(x))) +# define __REG2(x,y) (*(volatile u32 *)((u32)&__REG(x) + (y))) +# else +# define __REG(x) (x) +# ifdef CONFIG_CPU_MONAHANS /* Hack to make this work with mona's pxa-regs.h */ +# define __REG_2(x) (x) +# define __REG_3(x) (x) +# endif +# endif +#endif /* UBOOT_REG_FIX */ -#endif /* ifndef __ASSEMBLY__ */ +#include "pxa-regs.h" #ifndef __ASSEMBLY__ -#ifdef CONFIG_MACH_ZYLONITE -#include "zylonite.h" -#endif +/* + * GPIO edge detection for IRQs: + * IRQs are generated on Falling-Edge, Rising-Edge, or both. + * This must be called *before* the corresponding IRQ is registered. + * Use this instead of directly setting GRER/GFER. + */ +#define GPIO_FALLING_EDGE 1 +#define GPIO_RISING_EDGE 2 +#define GPIO_BOTH_EDGES 3 +extern void set_GPIO_IRQ_edge( int gpio_nr, int edge_mask ); /* * Handy routine to set GPIO alternate functions */ -extern void pxa_gpio_mode( int gpio_mode ); +extern void set_GPIO_mode( int gpio_mode ); /* - * Routine to enable or disable CKEN + * return current lclk frequency in units of 10kHz */ -extern void pxa_set_cken(int clock, int enable); +extern unsigned int get_lclk_frequency_10khz(void); + +#endif + /* - * return current memory and LCD clock frequency in units of 10kHz + * Implementation specifics */ -extern unsigned int get_memclk_frequency_10khz(void); -extern unsigned int get_lcdclk_frequency_10khz(void); -#endif /* __ASSEMBLY__ */ #ifdef CONFIG_ARCH_LUBBOCK #include "lubbock.h" @@ -159,15 +143,6 @@ extern unsigned int get_lcdclk_frequency_10khz(void); #include "cerf.h" #endif -#if CONFIG_CPU_MONAHANS_L2CACHE -#define __cpuc_flush_l2cache_all xscale_flush_l2cache_all -extern void __cpuc_flush_l2cache_all(void); -#define flush_l2cache_all __cpuc_flush_l2cache_all -#else -#define __cpuc_flush_l2cache_all() do {} while (0) -#define flush_l2cache_all() do {} while (0) -#endif - #ifdef CONFIG_ARCH_CSB226 #include "csb226.h" #endif @@ -180,10 +155,4 @@ extern void __cpuc_flush_l2cache_all(void); #include "pleb.h" #endif -#ifdef CONFIG_MACH_MAINSTONE -#include "mainstone.h" -#endif - -#include "pxa-regs.h" - -#endif /* _ASM_ARCH_HARDWARE_H */ +#endif /* _ASM_ARCH_HARDWARE_H */ diff --git a/include/asm-arm/global_data.h b/include/asm-arm/global_data.h index c2d52915a8..b3c7084352 100644 --- a/include/asm-arm/global_data.h +++ b/include/asm-arm/global_data.h @@ -61,6 +61,11 @@ typedef struct global_data { #define GD_FLG_DEVINIT 0x00002 /* Devices have been initialized */ #define GD_FLG_SILENT 0x00004 /* Silent mode */ -#define DECLARE_GLOBAL_DATA_PTR register volatile gd_t *gd asm ("r8") +#define GCC_4_SCREW_GDP 1 +#ifdef GCC_4_SCREW_GDP +# define DECLARE_GLOBAL_DATA_PTR register gd_t* volatile gd asm ("r8"); +#else +# define DECLARE_GLOBAL_DATA_PTR register volatile gd_t *gd asm ("r8") +#endif #endif /* __ASM_GBL_DATA_H */