From: Freddie Chopin <freddie_chopin@op.pl>
Date: Wed, 1 Dec 2010 21:55:56 +0000 (+0100)
Subject: rename some target scripts to be consistent with the rest
X-Git-Tag: v0.5.0-rc1~302
X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=a1ce28b118e758015a4e8ba1cb74815aa4193ee0;p=openocd

rename some target scripts to be consistent with the rest

Rename Atmel target scripts which had wrong name ("at91" missing for ARM7 AT91SAM7..., "at" missing for AVR ATmega...)

Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
---

diff --git a/tcl/target/at91sam7se512.cfg b/tcl/target/at91sam7se512.cfg
new file mode 100644
index 00000000..c48afeff
--- /dev/null
+++ b/tcl/target/at91sam7se512.cfg
@@ -0,0 +1,40 @@
+
+# ATMEL sam7se512
+# Example: the "Elektor Internet Radio" - EIR
+# http://www.ethernut.de/en/hardware/eir/index.html
+
+if { [info exists CHIPNAME] } {
+   set  _CHIPNAME $CHIPNAME
+} else {
+   set  _CHIPNAME sam7se512
+}
+
+if { [info exists ENDIAN] } {
+   set  _ENDIAN $ENDIAN
+} else {
+   set  _ENDIAN little
+}
+
+if { [info exists CPUTAPID ] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+  # force an error till we get a good number
+   set _CPUTAPID 0xffffffff
+}
+
+#use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config srst_only srst_pulls_trst
+
+#jtag scan chain
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+# The target
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi
+
+$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
+
+#flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>]
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME at91sam7 0 0 0 0 $_TARGETNAME 0 0 0 0 0 0 0 18432
+
diff --git a/tcl/target/at91sam7x256.cfg b/tcl/target/at91sam7x256.cfg
new file mode 100644
index 00000000..dd364585
--- /dev/null
+++ b/tcl/target/at91sam7x256.cfg
@@ -0,0 +1,50 @@
+#use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config srst_only srst_pulls_trst
+
+if { [info exists CHIPNAME] } {
+   set  _CHIPNAME $CHIPNAME
+} else {
+   set  _CHIPNAME sam7x256
+}
+
+if { [info exists ENDIAN] } {
+   set  _ENDIAN $ENDIAN
+} else {
+   set  _ENDIAN little
+}
+
+if { [info exists CPUTAPID ] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   set _CPUTAPID 0x3f0f0f0f
+}
+
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi
+
+$_TARGETNAME configure -event reset-init {
+	# disable watchdog
+	mww 0xfffffd44 0x00008000
+	# enable user reset
+	mww 0xfffffd08 0xa5000001
+	# CKGR_MOR : enable the main oscillator
+	mww 0xfffffc20 0x00000601
+	sleep 10
+	# CKGR_PLLR: 96.1097 MHz
+	mww 0xfffffc2c 0x00481c0e
+	sleep 10
+	# PMC_MCKR : MCK = PLL / 2 ~= 48 MHz
+	mww 0xfffffc30 0x00000007
+	sleep 10
+	# MC_FMR: flash mode (FWS=1,FMCN=60)
+	mww 0xffffff60 0x003c0100
+	sleep 100
+}
+
+$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
+
+#flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>]
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME at91sam7 0 0 0 0 $_TARGETNAME 0 0 0 0 0 0 0 18432
diff --git a/tcl/target/atmega128.cfg b/tcl/target/atmega128.cfg
new file mode 100644
index 00000000..212a2673
--- /dev/null
+++ b/tcl/target/atmega128.cfg
@@ -0,0 +1,40 @@
+# for avr
+
+   set  _CHIPNAME avr
+   set  _ENDIAN little
+
+# jtag speed
+adapter_khz 4500
+
+reset_config  srst_only
+adapter_nsrst_delay 100
+
+#jtag scan chain
+if { [info exists CPUTAPID ] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   set _CPUTAPID 0x8970203F
+}
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME avr -endian $_ENDIAN -chain-position $_TARGETNAME
+
+#$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0
+
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME avr 0 0 0 0 $_TARGETNAME
+
+#to use it, script will be like:
+#init
+#adapter_khz 4500
+#reset init
+#verify_ircapture disable
+#
+#halt
+#wait halt
+#poll
+#avr mass_erase 0
+#flash write_image E:/Versaloon/Software/CAMERAPROTOCOLAGENT.hex
+#reset run
+#shutdown
diff --git a/tcl/target/mega128.cfg b/tcl/target/mega128.cfg
deleted file mode 100644
index 212a2673..00000000
--- a/tcl/target/mega128.cfg
+++ /dev/null
@@ -1,40 +0,0 @@
-# for avr
-
-   set  _CHIPNAME avr
-   set  _ENDIAN little
-
-# jtag speed
-adapter_khz 4500
-
-reset_config  srst_only
-adapter_nsrst_delay 100
-
-#jtag scan chain
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-   set _CPUTAPID 0x8970203F
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME avr -endian $_ENDIAN -chain-position $_TARGETNAME
-
-#$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0
-
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME avr 0 0 0 0 $_TARGETNAME
-
-#to use it, script will be like:
-#init
-#adapter_khz 4500
-#reset init
-#verify_ircapture disable
-#
-#halt
-#wait halt
-#poll
-#avr mass_erase 0
-#flash write_image E:/Versaloon/Software/CAMERAPROTOCOLAGENT.hex
-#reset run
-#shutdown
diff --git a/tcl/target/sam7se512.cfg b/tcl/target/sam7se512.cfg
deleted file mode 100644
index c48afeff..00000000
--- a/tcl/target/sam7se512.cfg
+++ /dev/null
@@ -1,40 +0,0 @@
-
-# ATMEL sam7se512
-# Example: the "Elektor Internet Radio" - EIR
-# http://www.ethernut.de/en/hardware/eir/index.html
-
-if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
-} else {
-   set  _CHIPNAME sam7se512
-}
-
-if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
-} else {
-   set  _ENDIAN little
-}
-
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-  # force an error till we get a good number
-   set _CPUTAPID 0xffffffff
-}
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
-
-#jtag scan chain
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-# The target
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi
-
-$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
-
-#flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>]
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME at91sam7 0 0 0 0 $_TARGETNAME 0 0 0 0 0 0 0 18432
-
diff --git a/tcl/target/sam7x256.cfg b/tcl/target/sam7x256.cfg
deleted file mode 100644
index dd364585..00000000
--- a/tcl/target/sam7x256.cfg
+++ /dev/null
@@ -1,50 +0,0 @@
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
-
-if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
-} else {
-   set  _CHIPNAME sam7x256
-}
-
-if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
-} else {
-   set  _ENDIAN little
-}
-
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-   set _CPUTAPID 0x3f0f0f0f
-}
-
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi
-
-$_TARGETNAME configure -event reset-init {
-	# disable watchdog
-	mww 0xfffffd44 0x00008000
-	# enable user reset
-	mww 0xfffffd08 0xa5000001
-	# CKGR_MOR : enable the main oscillator
-	mww 0xfffffc20 0x00000601
-	sleep 10
-	# CKGR_PLLR: 96.1097 MHz
-	mww 0xfffffc2c 0x00481c0e
-	sleep 10
-	# PMC_MCKR : MCK = PLL / 2 ~= 48 MHz
-	mww 0xfffffc30 0x00000007
-	sleep 10
-	# MC_FMR: flash mode (FWS=1,FMCN=60)
-	mww 0xffffff60 0x003c0100
-	sleep 100
-}
-
-$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
-
-#flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>]
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME at91sam7 0 0 0 0 $_TARGETNAME 0 0 0 0 0 0 0 18432