From: Fabio Estevam <fabio.estevam@nxp.com>
Date: Tue, 5 Jan 2016 19:02:53 +0000 (-0200)
Subject: mx6sabresd: Simplify the Ethernet PHY configuration
X-Git-Tag: v2016.01~5^2~6
X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=a307760ab48b428f4c2ac8b5676b29c56eee9f82;p=u-boot

mx6sabresd: Simplify the Ethernet PHY configuration

As per the AR8031 datasheet:

"For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset
1ms requirement is satisfied."

So do as suggested and also add a 100us delay after deasserting the
reset line to guarantee that the PHY ID can be read correctly and the
Atheros 8031 PHY driver can be loaded automatically.

This results in a simpler code.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
---

diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 581c9d5560..d20953d2ca 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -94,8 +94,9 @@ static void setup_iomux_enet(void)
 
 	/* Reset AR8031 PHY */
 	gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
-	udelay(500);
+	mdelay(10);
 	gpio_set_value(IMX_GPIO_NR(1, 25), 1);
+	udelay(100);
 }
 
 static iomux_v3_cfg_t const usdhc2_pads[] = {
@@ -340,39 +341,6 @@ int board_mmc_init(bd_t *bis)
 }
 #endif
 
-int mx6_rgmii_rework(struct phy_device *phydev)
-{
-	unsigned short val;
-
-	/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
-
-	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
-	val &= 0xffe3;
-	val |= 0x18;
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
-
-	/* introduce tx clock delay */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
-	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
-	val |= 0x0100;
-	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
-
-	return 0;
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
-	mx6_rgmii_rework(phydev);
-
-	if (phydev->drv->config)
-		phydev->drv->config(phydev);
-
-	return 0;
-}
-
 #if defined(CONFIG_VIDEO_IPUV3)
 static void disable_lvds(struct display_info_t const *dev)
 {