From: wdenk Date: Sun, 6 Jun 2004 23:13:55 +0000 (+0000) Subject: * Patch by Dave Peverley, 30 Apr 2004: X-Git-Tag: LABEL_2006_03_12_0025~565 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=a56bd92289298bde16306bcc754277db45315d2f;p=u-boot * Patch by Dave Peverley, 30 Apr 2004: Add support for OMAP730 Perseus2 Development board * Patch by Alan J. Luse, 29 Apr 2004: Fix flash chip-select (OR0) option register setting on FADS boards. * Patch by Alan J. Luse, 29 Apr 2004: Report MII network speed and duplex setting properly when auto-negotiate is not enabled. * Patch by Jarrett Redd, 29 Apr 2004: Fix hang on reset on Ocotea board due to flash in wrong mode. --- diff --git a/CHANGELOG b/CHANGELOG index dfcc0f722e..f8628915c0 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,19 @@ Changes since U-Boot 1.1.1: ====================================================================== +* Patch by Dave Peverley, 30 Apr 2004: + Add support for OMAP730 Perseus2 Development board + +* Patch by Alan J. Luse, 29 Apr 2004: + Fix flash chip-select (OR0) option register setting on FADS boards. + +* Patch by Alan J. Luse, 29 Apr 2004: + Report MII network speed and duplex setting properly when + auto-negotiate is not enabled. + +* Patch by Jarrett Redd, 29 Apr 2004: + Fix hang on reset on Ocotea board due to flash in wrong mode. + * Patch by Dave Peverley, 29 Apr 2004: add MAC address detection to smc91111 driver diff --git a/CREDITS b/CREDITS index 9bed1e5837..14b131bdc9 100644 --- a/CREDITS +++ b/CREDITS @@ -285,6 +285,11 @@ D: Support for 4xx SCSI, floppy, CDROM, CT69000 video, ... D: Support for PIP405 board D: Support for MIP405 board +N: Dave Peverley +E: dpeverley@mpc-data.co.uk +W: http://www.mpc-data.co.uk +D: OMAP730 P2 board support + N: Bill Pitts E: wlp@mindspring.com D: BedBug embedded debugger code diff --git a/MAINTAINERS b/MAINTAINERS index 7a868001e7..430f082608 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -340,6 +340,9 @@ Kshitij Gupta omap1510inn ARM925T omap1610inn ARM926EJS +Dave Peverley + omap730p2 ARM926EJS + Nishant Kamat omap1610h2 ARM926EJS diff --git a/MAKEALL b/MAKEALL index 7c1576b0b6..228d96d956 100644 --- a/MAKEALL +++ b/MAKEALL @@ -139,8 +139,8 @@ LIST_ARM7="B2 ep7312 impa7" LIST_ARM9=" \ at91rm9200dk integratorcp integratorap \ omap1510inn omap1610h2 omap1610inn \ - smdk2400 smdk2410 trab \ - VCMA9 versatile \ + omap730p2 smdk2400 smdk2410 \ + trab VCMA9 versatile \ " ######################################################################### diff --git a/Makefile b/Makefile index 7b84baf629..407f5c4cfd 100644 --- a/Makefile +++ b/Makefile @@ -981,6 +981,8 @@ xtract_trab = $(subst _bigram,,$(subst _bigflash,,$(subst _old,,$(subst _config, xtract_omap1610xxx = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1))) +xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1))) + SX1_config : unconfig @./mkconfig $(@:_config=) arm arm925t sx1 @@ -1011,6 +1013,18 @@ omap1610h2_cs3boot_config : unconfig fi; @./mkconfig -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn +omap730p2_config \ +omap730p2_cs0boot_config \ +omap730p2_cs3boot_config : unconfig + @if [ "$(findstring _cs0boot_, $@)" ] ; then \ + echo "#define CONFIG_CS0_BOOT" >> ./include/config.h ; \ + echo "... configured for CS0 boot"; \ + else \ + echo "#define CONFIG_CS3_BOOT" >> ./include/config.h ; \ + echo "... configured for CS3 boot"; \ + fi; + @./mkconfig -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 + smdk2400_config : unconfig @./mkconfig $(@:_config=) arm arm920t smdk2400 diff --git a/README b/README index 95e552d208..5642c27dbe 100644 --- a/README +++ b/README @@ -294,8 +294,9 @@ The following options need to be configured: CONFIG_AT91RM9200DK, CONFIG_DNP1110, CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE, CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610, CONFIG_LART, - CONFIG_LUBBOCK, CONFIG_SHANNON, CONFIG_SMDK2400, - CONFIG_SMDK2410, CONFIG_TRAB, CONFIG_VCMA9, + CONFIG_LUBBOCK, CONFIG_SHANNON, CONFIG_P2_OMAP730, + CONFIG_SMDK2400, CONFIG_SMDK2410, CONFIG_TRAB, + CONFIG_VCMA9 MicroBlaze based boards: ------------------------ @@ -2074,6 +2075,7 @@ configurations; the following names are supported: FADS823_config NETVIA_config TQM860L_config FADS850SAR_config omap1510inn_config WALNUT405_config FADS860T_config omap1610h2_config ZPC1900_config + omap730p2_config Note: for some board special configuration names may exist; check if additional information is available from the board vendor; for diff --git a/board/fads/flash.c b/board/fads/flash.c index c23dff70b7..d2a46b2275 100644 --- a/board/fads/flash.c +++ b/board/fads/flash.c @@ -94,7 +94,7 @@ unsigned long flash_init (void) /* Remap FLASH according to real size */ memctl->memc_or0 = - ((((unsigned long) ~1) << i) & OR_AM_MSK) | + ((((unsigned long) ~0) << i) & OR_AM_MSK) | CFG_OR_TIMING_FLASH; memctl->memc_br0 = CFG_BR0_PRELIM; diff --git a/board/ocotea/flash.c b/board/ocotea/flash.c index 15e688f7a2..f44984a0e0 100644 --- a/board/ocotea/flash.c +++ b/board/ocotea/flash.c @@ -349,10 +349,14 @@ static ulong flash_get_size(vu_long * addr, flash_info_t * info) info->protect[i] = addr2[2] & 1; } + /* issue bank reset to return to read mode */ + addr2[0] = (FLASH_WORD_SIZE) 0x00F000F0; + /* * Prevent writes to uninitialized FLASH. */ if (info->flash_id != FLASH_UNKNOWN) { + /* ? ? ? */ } return (info->size); diff --git a/board/omap730p2/Makefile b/board/omap730p2/Makefile new file mode 100644 index 0000000000..1058508073 --- /dev/null +++ b/board/omap730p2/Makefile @@ -0,0 +1,47 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(BOARD).a + +OBJS := omap730p2.o flash.o +SOBJS := platform.o + +$(LIB): $(OBJS) $(SOBJS) + $(AR) crv $@ $^ + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +-include .depend + +######################################################################### diff --git a/board/omap730p2/config.mk b/board/omap730p2/config.mk new file mode 100644 index 0000000000..16bff6f271 --- /dev/null +++ b/board/omap730p2/config.mk @@ -0,0 +1,25 @@ +# +# (C) Copyright 2002 +# Gary Jennejohn, DENX Software Engineering, +# David Mueller, ELSOFT AG, +# +# (C) Copyright 2003 +# Texas Instruments, +# Kshitij Gupta +# +# TI Perseus 2 board with OMAP720 (ARM925EJS) cpu +# see http://www.ti.com/ for more information on Texas Instruments +# +# Innovator has 1 bank of 256 MB SDRAM +# Physical Address: +# 1000'0000 to 2000'0000 +# +# +# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000 +# (mem base + reserved) +# +# we load ourself to 1108'0000 +# +# + +TEXT_BASE = 0x11080000 diff --git a/board/omap730p2/flash.c b/board/omap730p2/flash.c new file mode 100644 index 0000000000..e7d65157f7 --- /dev/null +++ b/board/omap730p2/flash.c @@ -0,0 +1,477 @@ +/* + * (C) Copyright 2001 + * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net + * + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2003 + * Texas Instruments, + * Kshitij Gupta + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 256 KB sectors (x2) */ +flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +/* Board support for 1 or 2 flash devices */ +#undef FLASH_PORT_WIDTH32 +#define FLASH_PORT_WIDTH16 + +#ifdef FLASH_PORT_WIDTH16 +#define FLASH_PORT_WIDTH ushort +#define FLASH_PORT_WIDTHV vu_short +#define SWAP(x) __swab16(x) +#else +#define FLASH_PORT_WIDTH ulong +#define FLASH_PORT_WIDTHV vu_long +#define SWAP(x) __swab32(x) +#endif + +#define FPW FLASH_PORT_WIDTH +#define FPWV FLASH_PORT_WIDTHV + +#define mb() __asm__ __volatile__ ("" : : : "memory") + + +/* Flash Organization Structure */ +typedef struct OrgDef { + unsigned int sector_number; + unsigned int sector_size; +} OrgDef; + + +/* Flash Organizations */ +OrgDef OrgIntel_28F256L18T[] = { + {4, 32 * 1024}, /* 4 * 32kBytes sectors */ + {255, 128 * 1024}, /* 255 * 128kBytes sectors */ +}; + + +/*----------------------------------------------------------------------- + * Functions + */ +unsigned long flash_init (void); +static ulong flash_get_size (FPW * addr, flash_info_t * info); +static int write_data (flash_info_t * info, ulong dest, FPW data); +static void flash_get_offsets (ulong base, flash_info_t * info); +void inline spin_wheel (void); +void flash_print_info (flash_info_t * info); +void flash_unprotect_sectors (FPWV * addr); +int flash_erase (flash_info_t * info, int s_first, int s_last); +int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt); + +/*----------------------------------------------------------------------- + */ + +unsigned long flash_init (void) +{ + int i; + ulong size = 0; + for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) { + switch (i) { + case 0: + flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]); + flash_get_offsets (PHYS_FLASH_1, &flash_info[i]); + break; + default: + panic ("configured too many flash banks!\n"); + break; + } + size += flash_info[i].size; + } + + /* Protect monitor and environment sectors + */ + flash_protect (FLAG_PROTECT_SET, + CFG_FLASH_BASE, + CFG_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]); + + flash_protect (FLAG_PROTECT_SET, + CFG_ENV_ADDR, + CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]); + + return size; +} + +/*----------------------------------------------------------------------- + */ +static void flash_get_offsets (ulong base, flash_info_t * info) +{ + int i; + OrgDef *pOrgDef; + + pOrgDef = OrgIntel_28F256L18T; + if (info->flash_id == FLASH_UNKNOWN) { + return; + } + + if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) { + for (i = 0; i < info->sector_count; i++) { + if (i > 255) { + info->start[i] = base + (i * 0x8000); + info->protect[i] = 0; + } else { + info->start[i] = base + + (i * PHYS_FLASH_SECT_SIZE); + info->protect[i] = 0; + } + } + } +} + +/*----------------------------------------------------------------------- + */ +void flash_print_info (flash_info_t * info) +{ + int i; + + if (info->flash_id == FLASH_UNKNOWN) { + printf ("missing or unknown FLASH type\n"); + return; + } + + switch (info->flash_id & FLASH_VENDMASK) { + case FLASH_MAN_INTEL: + printf ("INTEL "); + break; + default: + printf ("Unknown Vendor "); + break; + } + + switch (info->flash_id & FLASH_TYPEMASK) { + case FLASH_28F256L18T: + printf ("FLASH 28F256L18T\n"); + break; + default: + printf ("Unknown Chip Type\n"); + break; + } + + printf (" Size: %ld MB in %d Sectors\n", + info->size >> 20, info->sector_count); + + printf (" Sector Start Addresses:"); + for (i = 0; i < info->sector_count; ++i) { + if ((i % 5) == 0) + printf ("\n "); + printf (" %08lX%s", + info->start[i], info->protect[i] ? " (RO)" : " "); + } + printf ("\n"); + return; +} + +/* + * The following code cannot be run from FLASH! + */ +static ulong flash_get_size (FPW * addr, flash_info_t * info) +{ + volatile FPW value; + + /* Write auto select command: read Manufacturer ID */ + addr[0x5555] = (FPW) 0x00AA00AA; + addr[0x2AAA] = (FPW) 0x00550055; + addr[0x5555] = (FPW) 0x00900090; + + mb (); + value = addr[0]; + + switch (value) { + + case (FPW) INTEL_MANUFACT: + info->flash_id = FLASH_MAN_INTEL; + break; + + default: + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + addr[0] = (FPW) 0x00FF00FF; /* restore read mode */ + return (0); /* no or unknown flash */ + } + + mb (); + value = addr[1]; /* device ID */ + switch (value) { + + case (FPW) (INTEL_ID_28F256L18T): + info->flash_id += FLASH_28F256L18T; + info->sector_count = 259; + info->size = 0x02000000; + break; /* => 32 MB */ + + default: + info->flash_id = FLASH_UNKNOWN; + break; + } + + if (info->sector_count > CFG_MAX_FLASH_SECT) { + printf ("** ERROR: sector count %d > max (%d) **\n", + info->sector_count, CFG_MAX_FLASH_SECT); + info->sector_count = CFG_MAX_FLASH_SECT; + } + + addr[0] = (FPW) 0x00FF00FF; /* restore read mode */ + + return (info->size); +} + + +/* unprotects a sector for write and erase + * on some intel parts, this unprotects the entire chip, but it + * wont hurt to call this additional times per sector... + */ +void flash_unprotect_sectors (FPWV * addr) +{ +#define PD_FINTEL_WSMS_READY_MASK 0x0080 + + *addr = (FPW) 0x00500050; /* clear status register */ + + /* this sends the clear lock bit command */ + *addr = (FPW) 0x00600060; + *addr = (FPW) 0x00D000D0; +} + + +/*----------------------------------------------------------------------- + */ + +int flash_erase (flash_info_t * info, int s_first, int s_last) +{ + int flag, prot, sect; + ulong type, start, last; + int rcode = 0; + + if ((s_first < 0) || (s_first > s_last)) { + if (info->flash_id == FLASH_UNKNOWN) { + printf ("- missing\n"); + } else { + printf ("- no sectors to erase\n"); + } + return 1; + } + + type = (info->flash_id & FLASH_VENDMASK); + if ((type != FLASH_MAN_INTEL)) { + printf ("Can't erase unknown flash type %08lx - aborted\n", + info->flash_id); + return 1; + } + + prot = 0; + for (sect = s_first; sect <= s_last; ++sect) { + if (info->protect[sect]) { + prot++; + } + } + + if (prot) { + printf ("- Warning: %d protected sectors will not be erased!\n", + prot); + } else { + printf ("\n"); + } + + + start = get_timer (0); + last = start; + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts (); + + /* Start erase on unprotected sectors */ + for (sect = s_first; sect <= s_last; sect++) { + if (info->protect[sect] == 0) { /* not protected */ + FPWV *addr = (FPWV *) (info->start[sect]); + FPW status; + + printf ("Erasing sector %2d ... ", sect); + + flash_unprotect_sectors (addr); + + /* arm simple, non interrupt dependent timer */ + reset_timer_masked (); + + *addr = (FPW) 0x00500050;/* clear status register */ + *addr = (FPW) 0x00200020;/* erase setup */ + *addr = (FPW) 0x00D000D0;/* erase confirm */ + + while (((status = + *addr) & (FPW) 0x00800080) != + (FPW) 0x00800080) { + if (get_timer_masked () > + CFG_FLASH_ERASE_TOUT) { + printf ("Timeout\n"); + /* suspend erase */ + *addr = (FPW) 0x00B000B0; + /* reset to read mode */ + *addr = (FPW) 0x00FF00FF; + rcode = 1; + break; + } + } + + /* clear status register cmd. */ + *addr = (FPW) 0x00500050; + *addr = (FPW) 0x00FF00FF;/* resest to read mode */ + printf (" done\n"); + } + } + return rcode; +} + +/*----------------------------------------------------------------------- + * Copy memory to flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + * 4 - Flash not identified + */ + +int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) +{ + ulong cp, wp; + FPW data; + int count, i, l, rc, port_width; + + if (info->flash_id == FLASH_UNKNOWN) { + return 4; + } +/* get lower word aligned address */ +#ifdef FLASH_PORT_WIDTH16 + wp = (addr & ~1); + port_width = 2; +#else + wp = (addr & ~3); + port_width = 4; +#endif + + /* + * handle unaligned start bytes + */ + if ((l = addr - wp) != 0) { + data = 0; + for (i = 0, cp = wp; i < l; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + for (; i < port_width && cnt > 0; ++i) { + data = (data << 8) | *src++; + --cnt; + ++cp; + } + for (; cnt == 0 && i < port_width; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + + if ((rc = write_data (info, wp, SWAP (data))) != 0) { + return (rc); + } + wp += port_width; + } + + /* + * handle word aligned part + */ + count = 0; + while (cnt >= port_width) { + data = 0; + for (i = 0; i < port_width; ++i) { + data = (data << 8) | *src++; + } + if ((rc = write_data (info, wp, SWAP (data))) != 0) { + return (rc); + } + wp += port_width; + cnt -= port_width; + if (count++ > 0x800) { + spin_wheel (); + count = 0; + } + } + + if (cnt == 0) { + return (0); + } + + /* + * handle unaligned tail bytes + */ + data = 0; + for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) { + data = (data << 8) | *src++; + --cnt; + } + for (; i < port_width; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + + return (write_data (info, wp, SWAP (data))); +} + +/*----------------------------------------------------------------------- + * Write a word or halfword to Flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +static int write_data (flash_info_t * info, ulong dest, FPW data) +{ + FPWV *addr = (FPWV *) dest; + ulong status; + int flag; + + /* Check if Flash is (sufficiently) erased */ + if ((*addr & data) != data) { + printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr); + return (2); + } + flash_unprotect_sectors (addr); + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts (); + *addr = (FPW) 0x00400040; /* write setup */ + *addr = data; + + /* arm simple, non interrupt dependent timer */ + reset_timer_masked (); + + /* wait while polling the status register */ + while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) { + if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) { + *addr = (FPW) 0x00FF00FF; /* restore read mode */ + return (1); + } + } + *addr = (FPW) 0x00FF00FF; /* restore read mode */ + return (0); +} + +void inline spin_wheel (void) +{ + static int p = 0; + static char w[] = "\\/-"; + + printf ("\010%c", w[p]); + (++p == 3) ? (p = 0) : 0; +} diff --git a/board/omap730p2/omap730p2.c b/board/omap730p2/omap730p2.c new file mode 100644 index 0000000000..5e2fa3b62e --- /dev/null +++ b/board/omap730p2/omap730p2.c @@ -0,0 +1,272 @@ +/* + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Marius Groeger + * + * (C) Copyright 2002 + * David Mueller, ELSOFT AG, + * + * (C) Copyright 2003 + * Texas Instruments, + * Kshitij Gupta + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#if defined(CONFIG_OMAP730) +#include <./configs/omap730.h> +#endif + +int test_boot_mode(void); +void spin_up_leds(void); +void flash__init (void); +void ether__init (void); +void set_muxconf_regs (void); +void peripheral_power_enable (void); + +#define FLASH_ON_CS0 1 +#define FLASH_ON_CS3 0 + +static inline void delay (unsigned long loops) +{ + __asm__ volatile ("1:\n" + "subs %0, %1, #1\n" + "bne 1b":"=r" (loops):"0" (loops)); +} + +int test_boot_mode(void) +{ + /* Check for CS0 and CS3 address decode swapping */ + if (*((volatile int *)EMIFS_CONFIG) & 0x00000002) + return(FLASH_ON_CS3); + else + return(FLASH_ON_CS0); +} + +/* Toggle backup LED indication */ +void toggle_backup_led(void) +{ + static int backupLEDState = 0; /* Init variable so that the LED will be ON the first time */ + volatile unsigned int *IOConfReg; + + + IOConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DATA_OUTPUT); + + if (backupLEDState != 0) { + *IOConfReg &= (0xFFFFEFFF); + backupLEDState = 0; + } else { + *IOConfReg |= (0x00001000); + backupLEDState = 1; + } +} + +/* + * Miscellaneous platform dependent initialisations + */ + +int board_init (void) +{ + volatile unsigned int *IOConfReg; + + + DECLARE_GLOBAL_DATA_PTR; + + /* arch number of OMAP 730 P2 Board - Same as the Innovator! */ + gd->bd->bi_arch_number = 491; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = 0x10000100; + + /* Configure MUX settings */ + set_muxconf_regs (); + + peripheral_power_enable (); + + + /* Backup LED indication via GPIO_140 -> Red led if MUX correctly setup */ + toggle_backup_led(); + + /* Hold GSM in reset until needed */ + *((volatile unsigned short *)M_CTL) &= ~1; + + + /* + * CSx timings, GPIO Mux ... setup + */ + + /* Flash: CS0 timings setup */ + *((volatile unsigned int *) FLASH_CFG_0) = 0x0000fff3; + *((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000088; + + /* Ethernet support trough the debug board */ + /* CS1 timings setup */ + *((volatile unsigned int *) FLASH_CFG_1) = 0x0000fff3; + *((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000000; + + /* this speeds up your boot a quite a bit. However to make it + * work, you need make sure your kernel startup flush bug is fixed. + * ... rkw ... + */ + icache_enable (); + + flash__init (); + ether__init (); + + return 0; +} + +int misc_init_r (void) +{ + /* currently empty */ + return (0); +} + +/****************************** + Routine: + Description: +******************************/ +void flash__init (void) +{ + unsigned int regval; + + regval = *((volatile unsigned int *) EMIFS_CONFIG); + /* Turn off write protection for flash devices. */ + regval = regval | 0x0001; + *((volatile unsigned int *) EMIFS_CONFIG) = regval; +} + +/************************************************************* + Routine:ether__init + Description: take the Ethernet controller out of reset and wait + for the EEPROM load to complete. +*************************************************************/ +void ether__init (void) +{ +#define LAN_RESET_REGISTER 0x0400001c + + *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000; + do { + *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0001; + udelay (100); + } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0001); + + do { + *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000; + udelay (100); + } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0000); + +#define ETH_CONTROL_REG 0x0400030b + + *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01; + udelay (100); +} + +/****************************** + Routine: + Description: +******************************/ +int dram_init (void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + + return 0; +} + +/****************************************************** + Routine: set_muxconf_regs + Description: Setting up the configuration Mux registers + specific to the hardware +*******************************************************/ +void set_muxconf_regs (void) +{ + volatile unsigned int *MuxConfReg; + /* set each registers to its reset value; */ + + /* + * Backup LED Indication + */ + + /* Configure MUXed pin. Mode 6: GPIO_140 */ + MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF10); + *MuxConfReg &= (0xFFFFFF1F); /* Clear D_MPU_LPG1 */ + *MuxConfReg |= 0x000000C0; /* Set D_MPU_LPG1 to 0x6 */ + + /* Configure GPIO_140 as output */ + MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DIRECTION_CONTROL); + *MuxConfReg &= (0xFFFFEFFF); /* Clear direction (output) for GPIO 140 */ + + /* + * Configure GPIOs for battery charge & feedback + */ + + /* Configure MUXed pin. Mode 6: GPIO_35 */ + MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3); + *MuxConfReg &= 0xFFFFFFF1; /* Clear M_CLK_OUT */ + *MuxConfReg |= 0x0000000C; /* Set M_CLK_OUT = 0x6 (GPIOs) */ + + /* Configure MUXed pin. Mode 6: GPIO_72,73,74 */ + MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF5); + *MuxConfReg &= 0xFFFF1FFF; /* Clear D_DDR */ + *MuxConfReg |= 0x0000C000; /* Set D_DDR = 0x6 (GPIOs) */ + + MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DIRECTION_CONTROL); + *MuxConfReg |= 0x00000100; /* Configure GPIO_72 as input */ + *MuxConfReg &= 0xFFFFFDFF; /* Configure GPIO_73 as output */ + + /* + * Allow battery charge + */ + + MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DATA_OUTPUT); + *MuxConfReg &= (0xFFFFFDFF); /* Clear GPIO_73 pin */ + + /* + * Configure MPU_EXT_NIRQ IO in IO_CONF9 register, + * It is used as the Ethernet controller interrupt + */ + MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF9); + *MuxConfReg &= 0x1FFFFFFF; +} + +/****************************************************** + Routine: peripheral_power_enable + Description: Enable the power for UART1 +*******************************************************/ +void peripheral_power_enable (void) +{ + volatile unsigned int *MuxConfReg; + + + /* Set up pins used by UART */ + + /* Start UART clock (48MHz) */ + MuxConfReg = (volatile unsigned int *) (PERSEUS_PCC_CONF_REG); + *MuxConfReg &= (0xFFFFFFF7); + *MuxConfReg |= (0x00000008); + + /* Get the UART pin in mode0 */ + MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3); + *MuxConfReg &= (0xFF1FFFFF); + *MuxConfReg &= (0xF1FFFFFF); +} diff --git a/board/omap730p2/platform.S b/board/omap730p2/platform.S new file mode 100644 index 0000000000..1f1c95a897 --- /dev/null +++ b/board/omap730p2/platform.S @@ -0,0 +1,395 @@ +/* + * Board specific setup info + * + * (C) Copyright 2003-2004 + * + * Texas Instruments, + * Kshitij Gupta + * + * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004 + * + * Modified for OMAP730 P2 Board by Dave Peverley, MPC-Data Limited + * (http://www.mpc-data.co.uk) + * + * TODO : Tidy up and change to use system register defines + * from omap730.h where possible. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +#if defined(CONFIG_OMAP730) +#include <./configs/omap730.h> +#endif + +_TEXT_BASE: + .word TEXT_BASE /* sdram load addr from config.mk */ + +.globl platformsetup +platformsetup: + /* Save callers address in r11 - r11 must never be modified */ + mov r11, lr + + /*------------------------------------------------------* + *mask all IRQs by setting all bits in the INTMR default* + *------------------------------------------------------*/ + mov r1, #0xffffffff + ldr r0, =REG_IHL1_MIR + str r1, [r0] + ldr r0, =REG_IHL2_MIR + str r1, [r0] + + /*------------------------------------------------------* + * Set up ARM CLM registers (IDLECT1) * + *------------------------------------------------------*/ + ldr r0, REG_ARM_IDLECT1 + ldr r1, VAL_ARM_IDLECT1 + str r1, [r0] + + /*------------------------------------------------------* + * Set up ARM CLM registers (IDLECT2) * + *------------------------------------------------------*/ + ldr r0, REG_ARM_IDLECT2 + ldr r1, VAL_ARM_IDLECT2 + str r1, [r0] + + /*------------------------------------------------------* + * Set up ARM CLM registers (IDLECT3) * + *------------------------------------------------------*/ + ldr r0, REG_ARM_IDLECT3 + ldr r1, VAL_ARM_IDLECT3 + str r1, [r0] + + + mov r1, #0x01 /* PER_EN bit */ + ldr r0, REG_ARM_RSTCT2 + strh r1, [r0] /* CLKM; Peripheral reset. */ + + /* Set CLKM to Sync-Scalable */ + /* I supposedly need to enable the dsp clock before switching */ + mov r1, #0x1000 + ldr r0, REG_ARM_SYSST + strh r1, [r0] + mov r0, #0x400 +1: + subs r0, r0, #0x1 /* wait for any bubbles to finish */ + bne 1b + ldr r1, VAL_ARM_CKCTL + ldr r0, REG_ARM_CKCTL + strh r1, [r0] + + /* a few nops to let settle */ + nop + nop + nop + nop + nop + nop + nop + nop + nop + nop + + /* setup DPLL 1 */ + /* Ramp up the clock to 96Mhz */ + ldr r1, VAL_DPLL1_CTL + ldr r0, REG_DPLL1_CTL + strh r1, [r0] + ands r1, r1, #0x10 /* Check if PLL is enabled. */ + beq lock_end /* Do not look for lock if BYPASS selected */ +2: + ldrh r1, [r0] + ands r1, r1, #0x01 /* Check the LOCK bit.*/ + beq 2b /* loop until bit goes hi. */ +lock_end: + + /*------------------------------------------------------* + * Turn off the watchdog during init... * + *------------------------------------------------------*/ + ldr r0, REG_WATCHDOG + ldr r1, WATCHDOG_VAL1 + str r1, [r0] + ldr r1, WATCHDOG_VAL2 + str r1, [r0] + ldr r0, REG_WSPRDOG + ldr r1, WSPRDOG_VAL1 + str r1, [r0] + ldr r0, REG_WWPSDOG + +watch1Wait: + ldr r1, [r0] + tst r1, #0x10 + bne watch1Wait + + ldr r0, REG_WSPRDOG + ldr r1, WSPRDOG_VAL2 + str r1, [r0] + ldr r0, REG_WWPSDOG +watch2Wait: + ldr r1, [r0] + tst r1, #0x10 + bne watch2Wait + + /* Set memory timings corresponding to the new clock speed */ + + /* Check execution location to determine current execution location + * and branch to appropriate initialization code. + */ + /* Compare physical SDRAM base & current execution location. */ + and r0, pc, #0xF0000000 + /* Compare. */ + cmp r0, #0 + /* Skip over EMIF-fast initialization if running from SDRAM. */ + bne skip_sdram + + /* + * Delay for SDRAM initialization. + */ + mov r3, #0x1800 /* value should be checked */ +3: + subs r3, r3, #0x1 /* Decrement count */ + bne 3b + + ldr r0, REG_SDRAM_CONFIG + ldr r1, SDRAM_CONFIG_VAL + str r1, [r0] + + ldr r0, REG_SDRAM_MRS_LEGACY + ldr r1, SDRAM_MRS_VAL + str r1, [r0] + +skip_sdram: + +common_tc: + /* slow interface */ + ldr r1, VAL_TC_EMIFS_CS0_CONFIG + ldr r0, REG_TC_EMIFS_CS0_CONFIG + str r1, [r0] /* Chip Select 0 */ + + ldr r1, VAL_TC_EMIFS_CS1_CONFIG + ldr r0, REG_TC_EMIFS_CS1_CONFIG + str r1, [r0] /* Chip Select 1 */ + ldr r1, VAL_TC_EMIFS_CS2_CONFIG + ldr r0, REG_TC_EMIFS_CS2_CONFIG + str r1, [r0] /* Chip Select 2 */ + ldr r1, VAL_TC_EMIFS_CS3_CONFIG + ldr r0, REG_TC_EMIFS_CS3_CONFIG + str r1, [r0] /* Chip Select 3 */ + + /* 48MHz clock request for UART1 */ + ldr r1, PERSEUS2_CONFIG_BASE + ldrh r0, [r1, #CONFIG_PCC_CONF] + orr r0, r0, #CONF_MOD_UART1_CLK_MODE_R + strh r0, [r1, #CONFIG_PCC_CONF] + + /* Initialize public and private rheas + * - set access factor 2 on both rhea / strobe + * - disable write buffer on strb0, enable write buffer on strb1 + */ + + ldr R0, REG_RHEA_PUB_CTL + ldr R1, REG_RHEA_PRIV_CTL + ldr R2, VAL_RHEA_CTL + strh R2, [R0] + strh R2, [R1] + mov R3, #2 /* disable write buffer on strb0, enable write buffer on strb1 */ + strh R3, [R0, #0x08] /* arm rhea control reg */ + strh R3, [R1, #0x08] + + /* enable IRQ and FIQ */ + + mrs r4, CPSR + bic r4, r4, #IRQ_MASK + bic r4, r4, #FIQ_MASK + msr CPSR, r4 + + /* set TAP CONF to TRI EMULATION */ + + ldr r1, [r0, #CONFIG_MODE2] + bic r1, r1, #0x18 + orr r1, r1, #0x10 + str r1, [r0, #CONFIG_MODE2] + + /* set tdbgen to 1 */ + + ldr r0, PERSEUS2_CONFIG_BASE + ldr r1, [r0, #CONFIG_MODE1] + mov r2, #0x10000 + orr r1, r1, r2 + str r1, [r0, #CONFIG_MODE1] + +#ifdef CONFIG_P2_OMAP1610 + /* inserting additional 2 clock cycle hold time for LAN */ + ldr r0, REG_TC_EMIFS_CS1_ADVANCED + ldr r1, VAL_TC_EMIFS_CS1_ADVANCED + str r1, [r0] +#endif + /* Start MPU Timer 1 */ + ldr r0, REG_MPU_LOAD_TIMER + ldr r1, VAL_MPU_LOAD_TIMER + str r1, [r0] + + ldr r0, REG_MPU_CNTL_TIMER + ldr r1, VAL_MPU_CNTL_TIMER + str r1, [r0] + + /* back to arch calling code */ + mov pc, r11 + + /* the literal pools origin */ + .ltorg + +REG_TC_EMIFS_CONFIG: /* 32 bits */ + .word 0xfffecc0c +REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */ + .word 0xfffecc10 +REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */ + .word 0xfffecc14 +REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */ + .word 0xfffecc18 +REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */ + .word 0xfffecc1c + +#ifdef CONFIG_P2_OMAP730 +REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */ + .word 0xfffecc54 +#endif + +/* MPU clock/reset/power mode control registers */ +REG_ARM_CKCTL: /* 16 bits */ + .word 0xfffece00 + +REG_ARM_IDLECT3: /* 16 bits */ + .word 0xfffece24 +REG_ARM_IDLECT2: /* 16 bits */ + .word 0xfffece08 +REG_ARM_IDLECT1: /* 16 bits */ + .word 0xfffece04 + +REG_ARM_RSTCT2: /* 16 bits */ + .word 0xfffece14 +REG_ARM_SYSST: /* 16 bits */ + .word 0xfffece18 +/* DPLL control registers */ +REG_DPLL1_CTL: /* 16 bits */ + .word 0xfffecf00 + +/* Watch Dog register */ +/* secure watchdog stop */ +REG_WSPRDOG: + .word 0xfffeb048 +/* watchdog write pending */ +REG_WWPSDOG: + .word 0xfffeb034 + +WSPRDOG_VAL1: + .word 0x0000aaaa +WSPRDOG_VAL2: + .word 0x00005555 + +/* SDRAM config is: auto refresh enabled, 16 bit 4 bank, + counter @8192 rows, 10 ns, 8 burst */ +REG_SDRAM_CONFIG: + .word 0xfffecc20 + +REG_SDRAM_MRS_LEGACY: + .word 0xfffecc24 + +REG_WATCHDOG: + .word 0xfffec808 + +REG_MPU_LOAD_TIMER: + .word 0xfffec600 +REG_MPU_CNTL_TIMER: + .word 0xfffec500 + +/* Public and private rhea bridge registers definition */ + +REG_RHEA_PUB_CTL: + .word 0xFFFECA00 + +REG_RHEA_PRIV_CTL: + .word 0xFFFED300 + +/* EMIFF SDRAM Configuration register + - self refresh disable + - auto refresh enabled + - SDRAM type 64 Mb, 16 bits bus 4 banks + - power down enabled + - SDRAM clock disabled + */ +SDRAM_CONFIG_VAL: + .word 0x0C017DF4 + +/* Burst full page length ; cas latency = 3 */ +SDRAM_MRS_VAL: + .word 0x00000037 + +VAL_ARM_CKCTL: + .word 0x6505 +VAL_DPLL1_CTL: + .word 0x3412 + +#ifdef CONFIG_P2_OMAP730 +VAL_TC_EMIFS_CS0_CONFIG: + .word 0x0000FFF3 +VAL_TC_EMIFS_CS1_CONFIG: + .word 0x00004278 +VAL_TC_EMIFS_CS2_CONFIG: + .word 0x00004278 +VAL_TC_EMIFS_CS3_CONFIG: + .word 0x00004278 +VAL_TC_EMIFS_CS1_ADVANCED: + .word 0x00000022 +#endif + +VAL_ARM_IDLECT1: + .word 0x00000400 +VAL_ARM_IDLECT2: + .word 0x00000886 +VAL_ARM_IDLECT3: + .word 0x00000015 + +WATCHDOG_VAL1: + .word 0x000000f5 +WATCHDOG_VAL2: + .word 0x000000a0 + +VAL_MPU_LOAD_TIMER: + .word 0xffffffff +VAL_MPU_CNTL_TIMER: + .word 0xffffffa1 + +VAL_RHEA_CTL: + .word 0xFF22 + +/* Config Register vals */ +PERSEUS2_CONFIG_BASE: + .word 0xFFFE1000 + +.equ CONFIG_PCC_CONF, 0xB4 +.equ CONFIG_MODE1, 0x10 +.equ CONFIG_MODE2, 0x14 +.equ CONF_MOD_UART1_CLK_MODE_R, 0x0A + +/* misc values */ +.equ IRQ_MASK, 0x80 // IRQ mask value +.equ FIQ_MASK, 0x40 // FIQ mask value diff --git a/board/omap730p2/u-boot.lds b/board/omap730p2/u-boot.lds new file mode 100644 index 0000000000..eee4813f38 --- /dev/null +++ b/board/omap730p2/u-boot.lds @@ -0,0 +1,51 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + . = ALIGN(4); + .text : + { + cpu/arm926ejs/start.o (.text) + *(.text) + } + . = ALIGN(4); + .rodata : { *(.rodata) } + . = ALIGN(4); + .data : { *(.data) } + . = ALIGN(4); + .got : { *(.got) } + + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/common/miiphyutil.c b/common/miiphyutil.c index 721d109a13..2b0dcf4f2c 100644 --- a/common/miiphyutil.c +++ b/common/miiphyutil.c @@ -147,15 +147,31 @@ int miiphy_speed (unsigned char addr) } #endif /* CONFIG_PHY_GIGE */ - if (miiphy_read (addr, PHY_ANLPAR, ®)) { - puts ("PHY speed1 read failed, assuming 10bT\n"); + /* Check Basic Management Control Register first. */ + if (miiphy_read (addr, PHY_BMCR, ®)) { + puts ("PHY speed read failed, assuming 10bT\n"); return (_10BASET); } - if ((reg & PHY_ANLPAR_100) != 0) { + /* Check if auto-negotiation is on. */ + if ((reg & PHY_BMCR_AUTON) != 0) { + /* Get auto-negotiation results. */ + if (miiphy_read (addr, PHY_ANLPAR, ®)) { + puts ("PHY AN speed read failed, assuming 10bT\n"); + return (_10BASET); + } + if ((reg & PHY_ANLPAR_100) != 0) { + return (_100BASET); + } else { + return (_10BASET); + } + } + /* Get speed from basic control settings. */ + else if (reg & PHY_BMCR_100MB) { return (_100BASET); } else { return (_10BASET); } + } @@ -182,16 +198,32 @@ int miiphy_duplex (unsigned char addr) } #endif /* CONFIG_PHY_GIGE */ - if (miiphy_read (addr, PHY_ANLPAR, ®)) { + /* Check Basic Management Control Register first. */ + if (miiphy_read (addr, PHY_BMCR, ®)) { puts ("PHY duplex read failed, assuming half duplex\n"); return (HALF); } + /* Check if auto-negotiation is on. */ + if ((reg & PHY_BMCR_AUTON) != 0) { + /* Get auto-negotiation results. */ + if (miiphy_read (addr, PHY_ANLPAR, ®)) { + puts ("PHY AN duplex read failed, assuming half duplex\n"); + return (HALF); + } - if ((reg & (PHY_ANLPAR_10FD | PHY_ANLPAR_TXFD)) != 0) { + if ((reg & (PHY_ANLPAR_10FD | PHY_ANLPAR_TXFD)) != 0) { + return (FULL); + } else { + return (HALF); + } + } + /* Get speed from basic control settings. */ + else if (reg & PHY_BMCR_DPLX) { return (FULL); } else { return (HALF); } + } #ifdef CFG_FAULT_ECHO_LINK_DOWN diff --git a/cpu/arm926ejs/start.S b/cpu/arm926ejs/start.S index 51a26052bb..ad5d84770e 100644 --- a/cpu/arm926ejs/start.S +++ b/cpu/arm926ejs/start.S @@ -3,7 +3,7 @@ * * Copyright (c) 2003 Texas Instruments * - * ----- Adapted for OMAP1610 from ARM925t code ------ + * ----- Adapted for OMAP1610 OMAP730 from ARM925t code ------ * * Copyright (c) 2001 Marius Gröger * Copyright (c) 2002 Alex Züpke @@ -36,6 +36,8 @@ #if defined(CONFIG_OMAP1610) #include <./configs/omap1510.h> +#elif defined(CONFIG_OMAP730) +#include <./configs/omap730.h> #endif /* diff --git a/doc/README.omap730p2 b/doc/README.omap730p2 new file mode 100644 index 0000000000..505234f38f --- /dev/null +++ b/doc/README.omap730p2 @@ -0,0 +1,95 @@ + + u-boot for the TI OMAP730 Perseus2 + + Dave Peverley, MPC-Data Limited + http://www.mpc-data.co.uk + + +Overview : + + As the OMAP730 is similar to the OMAP1610 in many ways, this port was based +on the u-boot port to the OMAP1610 Innovator. Supported features are : + + - Serial terminal support + - Onboard NOR Flash + - Ethernet via the seperate debug board + - Tested on Rev4 and Rev5 boards + + It has also been tested to work correctly when built with a 'standard' GCC +3.2.1 cross-compiler as well as Montavista Linux CEE 3.1's toolchain. + + + +Hardware Configuration : + + The main dips on the P2 board should be set to 2,3,7 and 9 on with all +others off. On the debug board, dips 1 and 7 should be on with the rest off. +The serial console has been set up to run from the DB9 connector on the +P2 board at 115200 baud, 8 data bits, no stop bits, 1 parity bit. + + It should be noted that the P2 board has NOR flash that is addressable via +either CS0 or CS3. This mode can be changed via DIP9 on the P2 board. + + + +Installing u-boot for the P2 : + + You can simply build u-boot for the Perseus by following the instructions +in the main readme file. The target configuration is "omap730p2_config". +Once u-boot has been built, you should strip the executable so it can be +loaded via CCS (which cant cope with the symbols in the ELF binary) : + $ cp u-boot u-boot.out + $ arm-linux-strip u-boot.out + + The method we've used for installing u-boot the first time on a P2 is +as follows : + +1) Configure TI Code Composer Studio to connect to the P2 board via JTAG + as described in the Users Guide. + +2) Set up the P2 to boot from CS3, and connect with CCS. Reset the CPU + and run the "init_mmu" GEL script. + +3) Use the "Load Program" option to send the u-boot.out file to the P2 and + run. + + At this point, u-boot should run and you will see the boot menu on your +serial terminal. You can then load the u-boot image to memory : + + # loadb 0x10000000 + + Send the "u-boot.bin" binary via the serial using Kermit. Once loaded +you can self-flash u-boot : + + # protect off 1:0 + # erase 1:0 + # cp.b 0x10000000 0x0 0x20000 + + You should now be able to reset the board and run u-boot from flash. + + + +Alternative flash option : + + Sometimes, if you've been silly, you can get the board into a state where +whats in flash has upset the board so much that you can no longer connect +to the P2 via JTAG. However, you can set DIP9 to off to swap the boot mode +of the P2 so that you boot from RAM instead of NOR flash. This moves NOR +flash up to 0x0C000000. You can build a special version of u-boot to +utilise this by the following config : + + $ make omap730p2_cs0boot_config + + If you load this up via CCS it will detect flash at its alternate location +and allow you to programme your u-boot image (which, remember must be built +for CS3 boot!) Once you do this, you can revert to CS3 boot and it will work +fine again. + + + +Errata : + +1) It's been observed that sometimes the tftp transfer of kernels to the + board can have checksum errors or stall. This appears to be an issue + with the lan91c96.c driver, and can normally be worked around by + resetting the board and trying again. diff --git a/drivers/lan91c96.c b/drivers/lan91c96.c index 032f9780af..c3b715c622 100644 --- a/drivers/lan91c96.c +++ b/drivers/lan91c96.c @@ -620,7 +620,7 @@ static int smc_open (bd_t *bd) address |= smc_mac_addr[i]; SMC_outw (address, LAN91C96_IA0 + i); } -#else +#else for (i = 0; i < 6; i++) SMC_outb (smc_mac_addr[i], LAN91C96_IA0 + i); #endif @@ -937,7 +937,7 @@ int smc_get_ethaddr (bd_t * bd) return (0); } -/* +/* * get_rom_mac() * Note, this has omly been tested for the OMAP730 P2. */ @@ -960,6 +960,4 @@ int get_rom_mac (char *v_rom_mac) #endif } - - #endif /* CONFIG_DRIVER_LAN91C96 */ diff --git a/drivers/ns16550.c b/drivers/ns16550.c index 05862ee6ec..f9fe819c1d 100644 --- a/drivers/ns16550.c +++ b/drivers/ns16550.c @@ -26,7 +26,7 @@ void NS16550_init (NS16550_t com_port, int baud_divisor) com_port->lcr = LCRVAL; com_port->mcr = MCRVAL; com_port->fcr = FCRVAL; -#if defined(CONFIG_OMAP1510) || defined(CONFIG_OMAP1610) +#if defined(CONFIG_OMAP1510) || defined(CONFIG_OMAP1610) || defined(CONFIG_OMAP730) com_port->mdr1 = 0; /* select uart mode */ #endif } diff --git a/include/configs/h2_p2_dbg_board.h b/include/configs/h2_p2_dbg_board.h new file mode 100644 index 0000000000..8a5ec34026 --- /dev/null +++ b/include/configs/h2_p2_dbg_board.h @@ -0,0 +1,145 @@ +/* + * + * BRIEF MODULE DESCRIPTION + * TI H2 and P2 Debug Board hardware map + * + * Copyright (C) 2004 MPC-Data Limited. (http://www.mpc-data.co.uk) + * Author: MPC-Data Limited + * Dave Peverley + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __INCLUDED_H2_P2_DBH_BOARD_H +#define __INCLUDED_H2_P2_DBH_BOARD_H + + +#include + + +/* + * The Debug board is designed to function with the P2 Sample, H2 + * Sample and 1610 Innovator boards. The main difference AFAICT is + * the chip selects used with each system ; + * + * P2 Sample : CS1 of OMAP730 is used to select the CPLD & LAN regs + * H2 Sample : CS1a is used to select the CPLD registers. + * + */ + + + +/*************************************************************************** + * CPLD Registers + **************************************************************************/ + +#define H2DBG_CPLD_REVISION 0x04000010 +#define H2DBG_BOARD_REVISION 0x04000012 +#define H2DBG_GPIO_REGISTER 0x04000014 +#define H2DBG_LED_CONTROL 0x04000016 +#define H2DBG_MISC_INPUT 0x04000018 +#define H2DBG_LAN_STATUS 0x0400001A +#define H2DBG_LAN_RESET 0x0400001C +#define H2DBG_ETH_REG_BASE 0x04000300 + + + +/*************************************************************************** + * Ethernet Control Registers + * These are for the LAN91C96 on the debug board + **************************************************************************/ + +/* Bank 0 in IO space */ + +#define ETH_TCR (H2DBG_ETH_REG_BASE + 0x00) /* Transmit Control Register */ +#define ETH_EPH_STATUS (H2DBG_ETH_REG_BASE + 0x02) /* EPH Status Register */ +#define ETH_RCR (H2DBG_ETH_REG_BASE + 0x04) /* Receive Control Register */ +#define ETH_COUNTER (H2DBG_ETH_REG_BASE + 0x06) /* Counter Register */ +#define ETH_MIR (H2DBG_ETH_REG_BASE + 0x08) /* Memory Information Register */ +#define ETH_MCR (H2DBG_ETH_REG_BASE + 0x0A) /* Memory Configuration Register */ + +/* Bank 1 in IO space */ + +#define ETH_CONFIG (H2DBG_ETH_REG_BASE + 0x00) /* Configuration Register */ +#define ETH_BASE (H2DBG_ETH_REG_BASE + 0x02) /* Base Address Register */ +#define ETH_IA0 (H2DBG_ETH_REG_BASE + 0x04) /* Individual Address Register - 0 */ +#define ETH_IA1 (H2DBG_ETH_REG_BASE + 0x05) /* Individual Address Register - 1 */ +#define ETH_IA2 (H2DBG_ETH_REG_BASE + 0x06) /* Individual Address Register - 2 */ +#define ETH_IA3 (H2DBG_ETH_REG_BASE + 0x07) /* Individual Address Register - 3 */ +#define ETH_IA4 (H2DBG_ETH_REG_BASE + 0x08) /* Individual Address Register - 4 */ +#define ETH_IA5 (H2DBG_ETH_REG_BASE + 0x09) /* Individual Address Register - 5 */ +#define ETH_GEN_PURPOSE (H2DBG_ETH_REG_BASE + 0x0A) /* General Address Registers */ +#define ETH_CONTROL (H2DBG_ETH_REG_BASE + 0x0B) /* Control Register */ + +/* Bank 2 in IO space */ + +#define ETH_MMU (H2DBG_ETH_REG_BASE + 0x00) /* MMU Command Register */ +#define ETH_AUTO_TX_START (H2DBG_ETH_REG_BASE + 0x01) /* Auto Tx Start Register */ +#define ETH_PNR (H2DBG_ETH_REG_BASE + 0x02) /* Packet Number Register */ +#define ETH_ARR (H2DBG_ETH_REG_BASE + 0x03) /* Allocation Result Register */ +#define ETH_FIFO (H2DBG_ETH_REG_BASE + 0x04) /* FIFO Ports Register */ +#define ETH_POINTER (H2DBG_ETH_REG_BASE + 0x06) /* Pointer Register */ +#define ETH_DATA_HIGH (H2DBG_ETH_REG_BASE + 0x08) /* Data High Register */ +#define ETH_DATA_LOW (H2DBG_ETH_REG_BASE + 0x0A) /* Data Low Register */ +#define ETH_INT_STATS (H2DBG_ETH_REG_BASE + 0x0C) /* Interrupt Status Register - RO */ +#define ETH_INT_ACK (H2DBG_ETH_REG_BASE + 0x0C) /* Interrupt Acknowledge Register -WO */ +#define ETH_INT_MASK (H2DBG_ETH_REG_BASE + 0x0D) /* Interrupt Mask Register */ + + +#ifndef __ASSEMBLY__ + +/* + * A couple of utility inlines to aid debugging using the LED's on the + * debug board. + */ + +static inline void set_led_state(int state) +{ + static unsigned long hw_led_state = 0; + volatile unsigned short *led_address = 0x04000016; + + hw_led_state = ((unsigned long)state); + *((unsigned short *) (led_address)) = (unsigned short) (~hw_led_state & 0xFFFF); +} + + +static inline void spin_up_leds() +{ + volatile int i, j, k; + + for (k = 0; k < 2; k++) { + for (i = 0; i < 16; i++) { + for (j = 0; j < 5000; j++) { + set_led_state(1 << i); + } + } + for (i = 15; i >= 0; i--) { + for (j = 0; j < 5000; j++) { + set_led_state(1 << i); + } + } + } +} + +#endif /* ! __ASSEMBLY__ */ + +#endif /* ! __INCLUDED_H2_P2_DBH_BOARD_H */ + diff --git a/include/configs/omap730.h b/include/configs/omap730.h new file mode 100644 index 0000000000..5fbbeb025e --- /dev/null +++ b/include/configs/omap730.h @@ -0,0 +1,287 @@ +/* + * + * BRIEF MODULE DESCRIPTION + * OMAP730 hardware map + * + * Copyright (C) 2004 MPC-Data Limited. (http://www.mpc-data.co.uk) + * Author: MPC-Data Limited + * Dave Peverley + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ + + +#ifndef __INCLUDED_OMAP730_H +#define __INCLUDED_OMAP730_H + +#include + + + + +/*************************************************************************** + * OMAP730 Configuration Registers + **************************************************************************/ + +#define PERSEUS2_MPU_DEV_ID ((unsigned int)(0xFFFE1000)) +#define PERSEUS2_GSM_DEV_ID0 ((unsigned int)(0xFFFE1000)) +#define PERSEUS2_GDM_DEV_ID1 ((unsigned int)(0xFFFE1002)) +#define DSP_CONF ((unsigned int)(0xFFFE1004)) +#define PERSEUS2_MPU_DIE_ID0 ((unsigned int)(0xFFFE1008)) +#define GSM_ASIC_CONF ((unsigned int)(0xFFFE1008)) +#define PERSEUS2_MPU_DIE_ID1 ((unsigned int)(0xFFFE100C)) +#define PERSEUS2_MODE1 ((unsigned int)(0xFFFE1010)) +#define PERSEUS2_GSM_DIE_ID0 ((unsigned int)(0xFFFE1010)) +#define PERSEUS2_GSM_DIE_ID1 ((unsigned int)(0xFFFE1012)) +#define PERSEUS2_MODE2 ((unsigned int)(0xFFFE1014)) +#define PERSEUS2_GSM_DIE_ID2 ((unsigned int)(0xFFFE1014)) +#define PERSEUS2_GSM_DIE_ID3 ((unsigned int)(0xFFFE1016)) +#define PERSEUS2_ANALOG_CELLS_CONF ((unsigned int)(0xFFFE1018)) +#define SPECCTL ((unsigned int)(0xFFFE101C)) +#define SPARE1 ((unsigned int)(0xFFFE1020)) +#define SPARE2 ((unsigned int)(0xFFFE1024)) +#define GSM_PBG_IRQ ((unsigned int)(0xFFFE1028)) +#define DMA_REQ_CONF ((unsigned int)(0xFFFE1030)) +#define PE_CONF_NO_DUAL ((unsigned int)(0xFFFE1060)) +#define PERSEUS2_IO_CONF0 ((unsigned int)(0xFFFE1070)) +#define PERSEUS2_IO_CONF1 ((unsigned int)(0xFFFE1074)) +#define PERSEUS2_IO_CONF2 ((unsigned int)(0xFFFE1078)) +#define PERSEUS2_IO_CONF3 ((unsigned int)(0xFFFE107C)) +#define PERSEUS2_IO_CONF4 ((unsigned int)(0xFFFE1080)) +#define PERSEUS2_IO_CONF5 ((unsigned int)(0xFFFE1084)) +#define PERSEUS2_IO_CONF6 ((unsigned int)(0xFFFE1088)) +#define PERSEUS2_IO_CONF7 ((unsigned int)(0xFFFE108C)) +#define PERSEUS2_IO_CONF8 ((unsigned int)(0xFFFE1090)) +#define PERSEUS2_IO_CONF9 ((unsigned int)(0xFFFE1094)) +#define PERSEUS2_IO_CONF10 ((unsigned int)(0xFFFE1098)) +#define PERSEUS2_IO_CONF11 ((unsigned int)(0xFFFE109C)) +#define PERSEUS2_IO_CONF12 ((unsigned int)(0xFFFE10A0)) +#define PERSEUS2_IO_CONF13 ((unsigned int)(0xFFFE10A4)) +#define PERSEUS_PCC_CONF_REG ((unsigned int)(0xFFFE10B4)) +#define BIST_STATUS_INTERNAL ((unsigned int)(0xFFFE10B8)) +#define BIST_CONTROL ((unsigned int)(0xFFFE10C0)) +#define BOOT_ROM_REG ((unsigned int)(0xFFFE10C4)) +#define PRODUCTION_ID_REG ((unsigned int)(0xFFFE10C8)) +#define BIST_SECROM_SIGNATURE1_INTERNAL ((unsigned int)(0xFFFE10D0)) +#define BIST_SECROM_SIGNATURE2_INTERNAL ((unsigned int)(0xFFFE10D4)) +#define BIST_CONTROL_2 ((unsigned int)(0xFFFE10D8)) +#define DEBUG1 ((unsigned int)(0xFFFE10E0)) +#define DEBUG2 ((unsigned int)(0xFFFE10E4)) +#define DEBUG_DMA_IRQ ((unsigned int)(0xFFFE10E8)) + + + + +/*************************************************************************** + * OMAP730 EMIFS Registers (TRM 2.5.7) + **************************************************************************/ + +#define TCMIF_BASE 0xFFFECC00 + +#define EMIFS_LRUREG (TCMIF_BASE + 0x04) +#define EMIFS_CONFIG (TCMIF_BASE + 0x0C) +#define FLASH_CFG_0 (TCMIF_BASE + 0x10) +#define FLASH_CFG_1 (TCMIF_BASE + 0x14) +#define FLASH_CFG_2 (TCMIF_BASE + 0x18) +#define FLASH_CFG_3 (TCMIF_BASE + 0x1C) +#define FL_CFG_DYN_WAIT (TCMIF_BASE + 0x40) +#define EMIFS_TIMEOUT1_REG (TCMIF_BASE + 0x28) +#define EMIFS_TIMEOUT2_REG (TCMIF_BASE + 0x2C) +#define EMIFS_TIMEOUT3_REG (TCMIF_BASE + 0x30) +#define EMIFS_ABORT_ADDR (TCMIF_BASE + 0x44) +#define EMIFS_ABORT_TYPE (TCMIF_BASE + 0x48) +#define EMIFS_ABORT_TOUT (TCMIF_BASE + 0x4C) +#define FLASH_ACFG_0_1 (TCMIF_BASE + 0x50) +#define FLASH_ACFG_1_1 (TCMIF_BASE + 0x54) +#define FLASH_ACFG_2_1 (TCMIF_BASE + 0x58) +#define FLASH_ACFG_3_1 (TCMIF_BASE + 0x5C) + + + +/*************************************************************************** + * OMAP730 Interrupt handlers + **************************************************************************/ + +#define OMAP_IH1_BASE 0xFFFECB00 /* MPU Level 1 IRQ handler */ +#define OMAP_IH2_BASE 0xfffe0000 + + + +/*************************************************************************** + * OMAP730 Timers + * + * There are three general purpose OS timers in the 730 that can be + * configured in autoreload or one-shot modes. + **************************************************************************/ + +#define OMAP730_32kHz_TIMER_BASE 0xFFFB9000 + +/* 32k Timer Registers */ +#define TIMER32k_CR 0x08 +#define TIMER32k_TVR 0x00 +#define TIMER32k_TCR 0x04 + +/* 32k Timer Control Register definition */ +#define TIMER32k_TSS (1<<0) +#define TIMER32k_TRB (1<<1) +#define TIMER32k_INT (1<<2) +#define TIMER32k_ARL (1<<3) + +/* MPU Timer base addresses */ +#define OMAP730_MPUTIMER_BASE 0xfffec500 +#define OMAP730_MPUTIMER_OFF 0x00000100 + +#define OMAP730_TIMER1_BASE 0xFFFEC500 +#define OMAP730_TIMER2_BASE 0xFFFEC600 +#define OMAP730_TIMER3_BASE 0xFFFEC700 + +/* MPU Timer Register offsets */ +#define CNTL_TIMER 0x00 /* MPU_CNTL_TIMER */ +#define LOAD_TIM 0x04 /* MPU_LOAD_TIMER */ +#define READ_TIM 0x08 /* MPU_READ_TIMER */ + +/* MPU_CNTL_TIMER register bits */ +#define MPUTIM_FREE (1<<6) +#define MPUTIM_CLOCK_ENABLE (1<<5) +#define MPUTIM_PTV_MASK (0x7< + * + * Configuation settings for the TI OMAP Perseus 2 board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + + +/* + * If we are developing, we might want to start armboot from ram + * so we MUST NOT initialize critical regs like mem-timing ... + */ + +#define CONFIG_INIT_CRITICAL /* undef for developing */ + + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_ARM926EJS 1 /* This is an arm926ejs CPU core */ +#define CONFIG_OMAP 1 /* in a TI OMAP core */ +#define CONFIG_OMAP730 1 /* which is in a 730 */ +#define CONFIG_P2_OMAP730 1 /* a Perseus 2 Board */ + + +/* + * Input clock of PLL + * The OMAP730 Perseus 2 has 13MHz input clock + */ + +#define CONFIG_SYS_CLK_FREQ 13000000 + +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#define CONFIG_MISC_INIT_R + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 + + +/* + * Size of malloc() pool + */ + +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + + +/* + * Hardware drivers + */ + +#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_LAN91C96_BASE 0x04000300 +#define CONFIG_LAN91C96_EXT_PHY + + +/* + * NS16550 Configuration + */ + +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE (1) +#define CFG_NS16550_CLK (48000000) /* can be 12M/32Khz or 48Mhz */ +#define CFG_NS16550_COM1 0xfffb0000 /* uart1, bluetooth uart + * on perseus */ + +/* + * select serial console configuration + */ + +#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on OMAP730 Perseus 2 */ + + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP) +#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT + +/* + * This must be included AFTER the definition of CONFIG_COMMANDS (if any) + */ + +#include +#include +#include + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTARGS "mem=32M console=ttyS0,115200n8 noinitrd root=/dev/nfs rw ip=bootp" + +#define CONFIG_LOADADDR 0x10000000 + +#define CONFIG_ETHADDR +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_IPADDR 192.168.0.23 +#define CONFIG_SERVERIP 192.150.0.100 +#define CONFIG_BOOTFILE "uImage" /* File to load */ + +#if defined (CONFIG_COMMANDS) && defined (CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 115200 /* Speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 1 /* Which serial port to use */ +#endif + + +/* + * Miscellaneous configurable options + */ + +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "OMAP730 P2 # " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x10000000 /* memtest works on */ +#define CFG_MEMTEST_END 0x12000000 /* 32 MB in DRAM */ + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR 0x10000000 /* default load address */ + + +/* The OMAP730 has 3 general purpose MPU timers, they can be driven by + * the RefClk (12Mhz) or by DPLL1. This time is further subdivided by a + * local divisor. + */ + +#define CFG_TIMERBASE 0xFFFEC500 /* use timer 1 */ +#define CFG_PVT 7 /* 2^(pvt+1), divide by 256 */ +#define CFG_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CFG_PVT)) + + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ + +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ + +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ + +#if defined(CONFIG_CS0_BOOT) +#define PHYS_FLASH_1 0x0C000000 +#elif defined(CONFIG_CS3_BOOT) +#define PHYS_FLASH_1 0x00000000 +#else +#error Unknown Boot Chip-Select number +#endif + +#define CFG_FLASH_BASE PHYS_FLASH_1 + + + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ + +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define PHYS_FLASH_SIZE 0x02000000 /* 32MB */ +#define CFG_MAX_FLASH_SECT (259) /* max number of sectors on one chip */ +/* addr of environment */ +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x020000) + + +/* timeout values are in ticks */ +#define CFG_FLASH_ERASE_TOUT (20*CFG_HZ) /* Timeout for Flash Erase */ +#define CFG_FLASH_WRITE_TOUT (20*CFG_HZ) /* Timeout for Flash Write */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */ +#define CFG_ENV_OFFSET 0x20000 /* environment starts here */ + + + +#endif /* ! __CONFIG_H */ diff --git a/include/ns16550.h b/include/ns16550.h index 4dd39fee32..5890246a87 100644 --- a/include/ns16550.h +++ b/include/ns16550.h @@ -19,6 +19,18 @@ struct NS16550 { unsigned char lsr; /* 5 */ unsigned char msr; /* 6 */ unsigned char scr; /* 7 */ +#if defined(CONFIG_OMAP730) + unsigned char mdr1; /* 8 */ + unsigned char reg9; /* 9 */ + unsigned char regA; /* A */ + unsigned char regB; /* B */ + unsigned char regC; /* C */ + unsigned char regD; /* D */ + unsigned char regE; /* E */ + unsigned char regF; /* F */ + unsigned char reg10; /* 10 */ + unsigned char ssr; /* 11*/ +#endif } __attribute__ ((packed)); #elif (CFG_NS16550_REG_SIZE == 2) struct NS16550 {