From: Timur Tabi Date: Sat, 4 Nov 2006 01:15:00 +0000 (-0600) Subject: mpc83xx: Update 83xx to use fsl_i2c.c X-Git-Tag: U-Boot-1_2_0~17^2~6 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=be5e61815d5a1fac290ce9c0ef09cb6a8e4288fa;p=u-boot mpc83xx: Update 83xx to use fsl_i2c.c Update the 83xx tree to use I2C support in drivers/fsl_i2c.c. Delete cpu/mpc83xx/i2c.c, include/asm-ppc/i2c.h, and all references to those files. Added multiple I2C bus support to fsl_i2c.c. Signed-off-by: Timur Tabi --- diff --git a/README b/README index 5c907c8f07..d03862b3ef 100644 --- a/README +++ b/README @@ -1342,6 +1342,17 @@ The following options need to be configured: will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1 + CFG_SPD_BUS_NUM + + If defined, then this indicates the I2C bus number for DDR SPD. + If not defined, then U-Boot assumes that SPD is on I2C bus 0. + + CONFIG_FSL_I2C + + Define this option if you want to use Freescale's I2C driver in + drivers/fsl_i2c.c. + + - SPI Support: CONFIG_SPI Enables SPI driver (so far only tested with diff --git a/board/mpc8349emds/pci.c b/board/mpc8349emds/pci.c index da49a5d80d..bb60e730bc 100644 --- a/board/mpc8349emds/pci.c +++ b/board/mpc8349emds/pci.c @@ -74,9 +74,7 @@ pib_init(void) */ /* Switch temporarily to I2C bus #2 */ orig_i2c_bus = i2c_get_bus_num(); - - if(orig_i2c_bus != 2) - i2c_set_bus_num(2); + i2c_set_bus_num(1); val8 = 0; i2c_write(0x23, 0x6, 1, &val8, 1); @@ -122,8 +120,7 @@ pib_init(void) printf("PCI2: 32-bit on PMC3\n"); #endif /* Reset to original I2C bus */ - if(orig_i2c_bus != 2) - i2c_set_bus_num(orig_i2c_bus); + i2c_set_bus_num(orig_i2c_bus); } /************************************************************************** diff --git a/board/mpc8349itx/mpc8349itx.c b/board/mpc8349itx/mpc8349itx.c index c0e72c93e1..097bb370e7 100644 --- a/board/mpc8349itx/mpc8349itx.c +++ b/board/mpc8349itx/mpc8349itx.c @@ -134,8 +134,7 @@ volatile static struct pci_controller hose[] = { }; #endif /* CONFIG_PCI */ -/* If MPC8349E-mITX is soldered with SDRAM, then initialize it. -*/ +/* If MPC8349E-mITX is soldered with SDRAM, then initialize it. */ void sdram_init(void) { @@ -255,32 +254,12 @@ long int initdram(int board_type) int checkboard(void) { -#ifdef CONFIG_HARD_I2C - u8 i2c_data; -#endif - - puts("Board: Freescale MPC8349E-mITX"); - -#ifdef CONFIG_HARD_I2C - i2c_set_bus_num(2); - if (i2c_read(CFG_I2C_8574A_ADDR2, 0, 0, &i2c_data, sizeof(i2c_data)) == - 0) - printf(" %u.%u (PCF8475A)", (i2c_data & 0x02) >> 1, - i2c_data & 0x01); - else if (i2c_read(CFG_I2C_8574_ADDR2, 0, 0, &i2c_data, sizeof(i2c_data)) - == 0) - printf(" %u.%u (PCF8475)", (i2c_data & 0x02) >> 1, - i2c_data & 0x01); - else - printf(" ?.?"); -#endif - - puts("\n"); + puts("Board: Freescale MPC8349E-mITX\n"); return 0; } -/** +/* * Implement a work-around for a hardware problem with compact * flash. * @@ -347,7 +326,7 @@ int misc_init_f(void) return 0; } -/** +/* * Make sure the EEPROM has the HRCW correctly programmed. * Make sure the RTC is correctly programmed. * @@ -366,7 +345,8 @@ int misc_init_r(void) #ifdef CONFIG_HARD_I2C - uchar orig_bus = i2c_get_bus_num();; + unsigned int orig_bus = i2c_get_bus_num();; + u8 i2c_data; #ifdef CFG_I2C_RTC_ADDR char ds1339_data[17]; @@ -381,8 +361,21 @@ int misc_init_r(void) }; u8 data[sizeof(eeprom_data)]; +#endif + printf("Board revision: "); i2c_set_bus_num(1); + if (i2c_read(CFG_I2C_8574A_ADDR2, 0, 0, &i2c_data, sizeof(i2c_data)) == 0) + printf("%u.%u (PCF8475A)\n", (i2c_data & 0x02) >> 1, i2c_data & 0x01); + else if (i2c_read(CFG_I2C_8574_ADDR2, 0, 0, &i2c_data, sizeof(i2c_data)) == 0) + printf("%u.%u (PCF8475)\n", (i2c_data & 0x02) >> 1, i2c_data & 0x01); + else { + printf("Unknown\n"); + rc = 1; + } + +#ifdef CFG_I2C_EEPROM_ADDR + i2c_set_bus_num(0); if (i2c_read(CFG_I2C_EEPROM_ADDR, 0, 2, data, sizeof(data)) == 0) { if (memcmp(data, eeprom_data, sizeof(data)) != 0) { @@ -400,7 +393,7 @@ int misc_init_r(void) #endif #ifdef CFG_I2C_RTC_ADDR - i2c_set_bus_num(2); + i2c_set_bus_num(1); if (i2c_read(CFG_I2C_RTC_ADDR, 0, 1, ds1339_data, sizeof(ds1339_data)) == 0) { diff --git a/board/mpc8349itx/pci.c b/board/mpc8349itx/pci.c index 535cc34afc..e81ad27356 100644 --- a/board/mpc8349itx/pci.c +++ b/board/mpc8349itx/pci.c @@ -29,6 +29,9 @@ #include #include #include +#if defined(CONFIG_OF_FLAT_TREE) +#include +#endif DECLARE_GLOBAL_DATA_PTR; @@ -105,7 +108,7 @@ void pci_init_board(void) udelay(2000); #ifdef CONFIG_HARD_I2C - i2c_set_bus_num(2); + i2c_set_bus_num(1); /* Read the PCI_M66EN jumper setting */ if ((i2c_read(CFG_I2C_8574_ADDR2, 0, 0, ®8, sizeof(reg8)) == 0) || (i2c_read(CFG_I2C_8574A_ADDR2, 0, 0, ®8, sizeof(reg8)) == 0)) { diff --git a/board/mpc8360emds/pci.c b/board/mpc8360emds/pci.c index a013ba3d43..15a48dcf40 100644 --- a/board/mpc8360emds/pci.c +++ b/board/mpc8360emds/pci.c @@ -19,7 +19,7 @@ #include #include -#include +#include DECLARE_GLOBAL_DATA_PTR; @@ -200,9 +200,7 @@ void pci_init_board(void) /* Switch temporarily to I2C bus #2 */ orig_i2c_bus = i2c_get_bus_num(); - - if(orig_i2c_bus != 2) - i2c_set_bus_num(2); + i2c_set_bus_num(1); val8 = 0; i2c_write(0x23, 0x6, 1, &val8, 1); @@ -231,12 +229,7 @@ void pci_init_board(void) asm("eieio"); /* Reset to original I2C bus */ - if(orig_i2c_bus != 2) - i2c_set_bus_num(orig_i2c_bus); - - /* Reset to original I2C bus */ - if(orig_i2c_bus != 2) - i2c_set_bus_num(orig_i2c_bus); + i2c_set_bus_num(orig_i2c_bus); /* * Release PCI RST Output signal diff --git a/cpu/mpc83xx/Makefile b/cpu/mpc83xx/Makefile index e254ef98f6..4b9dcc8180 100644 --- a/cpu/mpc83xx/Makefile +++ b/cpu/mpc83xx/Makefile @@ -29,7 +29,7 @@ LIB = $(obj)lib$(CPU).a START = start.o COBJS = traps.o cpu.o cpu_init.o speed.o interrupts.o \ - i2c.o spd_sdram.o qe_io.o + spd_sdram.o qe_io.o SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) diff --git a/cpu/mpc83xx/cpu.c b/cpu/mpc83xx/cpu.c index 0bd05330de..1d169bab22 100644 --- a/cpu/mpc83xx/cpu.c +++ b/cpu/mpc83xx/cpu.c @@ -111,7 +111,7 @@ int checkcpu(void) } -/** +/* * Program a UPM with the code supplied in the table. * * The 'dummy' variable is used to increment the MAD. 'dummy' is @@ -137,7 +137,7 @@ int checkcpu(void) * upm: 0=UPMA, 1=UPMB, 2=UPMC * table: Pointer to an array of values to program * size: Number of elements in the array. Must be 64 or less. -*/ + */ void upmconfig (uint upm, uint *table, uint size) { #if defined(CONFIG_MPC834X) diff --git a/cpu/mpc83xx/i2c.c b/cpu/mpc83xx/i2c.c deleted file mode 100644 index ce78491616..0000000000 --- a/cpu/mpc83xx/i2c.c +++ /dev/null @@ -1,423 +0,0 @@ -/* - * (C) Copyright 2006 Freescale Semiconductor, Inc. - * - * (C) Copyright 2003,Motorola Inc. - * Xianghua Xiao - * Adapted for Motorola 85xx chip. - * - * (C) Copyright 2003 - * Gleb Natapov - * Some bits are taken from linux driver writen by adrian@humboldt.co.uk - * - * Hardware I2C driver for MPC107 PCI bridge. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - * - * Change log: - * - * 20050101: Eran Liberty (liberty@freescale.com) - * Initial file creating (porting from 85XX & 8260) - * 20060601: Dave Liu (daveliu@freescale.com) - * Unified variable names for mpc83xx - */ - -#include -#include -#include - -#ifdef CONFIG_HARD_I2C -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -/* Initialize the bus pointer to whatever one the SPD EEPROM is on. - * Default is bus 1. This is necessary because the DDR initialization - * runs from ROM, and we can't switch buses because we can't modify - * the i2c_dev variable. Everything gets straightened out once i2c_init - * is called from RAM. */ - -#ifndef CFG_SPD_BUS_NUM -#define CFG_SPD_BUS_NUM 1 -#endif - -static unsigned int i2c_bus_num = CFG_SPD_BUS_NUM; - -#if CFG_SPD_BUS_NUM == 1 -static volatile i2c_t *i2c_dev = I2C_1; -#else -static volatile i2c_t *i2c_dev = I2C_2; -#endif - -static int i2c_bus_speed[2] = {0, 0}; - -/* - * Map the frequency divider to the FDR. This data is taken from table 17-5 - * of the MPC8349EA reference manual, with duplicates removed. - */ -static struct { - unsigned int divider; - u8 fdr; -} i2c_speed_map[] = -{ - {0, 0x20}, - {256, 0x20}, - {288, 0x21}, - {320, 0x22}, - {352, 0x23}, - {384, 0x24}, - {416, 0x01}, - {448, 0x25}, - {480, 0x02}, - {512, 0x26}, - {576, 0x27}, - {640, 0x28}, - {704, 0x05}, - {768, 0x29}, - {832, 0x06}, - {896, 0x2A}, - {1024, 0x2B}, - {1152, 0x08}, - {1280, 0x2C}, - {1536, 0x2D}, - {1792, 0x2E}, - {1920, 0x0B}, - {2048, 0x2F}, - {2304, 0x0C}, - {2560, 0x30}, - {3072, 0x31}, - {3584, 0x32}, - {3840, 0x0F}, - {4096, 0x33}, - {4608, 0x10}, - {5120, 0x34}, - {6144, 0x35}, - {7168, 0x36}, - {7680, 0x13}, - {8192, 0x37}, - {9216, 0x14}, - {10240, 0x38}, - {12288, 0x39}, - {14336, 0x3A}, - {15360, 0x17}, - {16384, 0x3B}, - {18432, 0x18}, - {20480, 0x3C}, - {24576, 0x3D}, - {28672, 0x3E}, - {30720, 0x1B}, - {32768, 0x3F}, - {36864, 0x1C}, - {40960, 0x1D}, - {49152, 0x1E}, - {61440, 0x1F}, - {-1, 0x1F} -}; - -#define NUM_I2C_SPEEDS (sizeof(i2c_speed_map) / sizeof(i2c_speed_map[0])) - -static int set_speed(unsigned int speed) -{ - unsigned long i2c_clk; - unsigned int divider, i; - u8 fdr = 0x3F; - - i2c_clk = (i2c_bus_num == 2) ? gd->i2c2_clk : gd->i2c1_clk; - - divider = i2c_clk / speed; - - /* Scan i2c_speed_map[] for the closest matching divider.*/ - - for (i = 0; i < NUM_I2C_SPEEDS-1; i++) { - /* Locate our divider in between two entries in i2c_speed_map[] */ - if ((divider >= i2c_speed_map[i].divider) && - (divider <= i2c_speed_map[i+1].divider)) { - /* Which one is closer? */ - if ((divider - i2c_speed_map[i].divider) < (i2c_speed_map[i+1].divider - divider)) { - fdr = i2c_speed_map[i].fdr; - } else { - fdr = i2c_speed_map[i+1].fdr; - } - break; - } - } - - writeb(fdr, &i2c_dev->fdr); - i2c_bus_speed[i2c_bus_num - 1] = speed; - - return 0; -} - - -static void _i2c_init(int speed, int slaveadd) -{ - /* stop I2C controller */ - writeb(0x00 , &i2c_dev->cr); - - /* set clock */ - set_speed(speed); - - /* set default filter */ - writeb(IC2_FDR,&i2c_dev->dfsrr); - - /* write slave address */ - writeb(slaveadd, &i2c_dev->adr); - - /* clear status register */ - writeb(I2C_CR_MTX, &i2c_dev->sr); - - /* start I2C controller */ - writeb(I2C_CR_MEN, &i2c_dev->cr); -} - -void i2c_init(int speed, int slaveadd) -{ - /* Set both interfaces to the same speed and slave address */ - /* Note: This function gets called twice - before and after - * relocation to RAM. The first time it's called, we are unable - * to change buses, so whichever one 'i2c_dev' was initialized to - * gets set twice. When run from RAM both buses get set properly */ - - i2c_set_bus_num(1); - _i2c_init(speed, slaveadd); -#ifdef CFG_I2C2_OFFSET - i2c_set_bus_num(2); - _i2c_init(speed, slaveadd); - i2c_set_bus_num(1); -#endif /* CFG_I2C2_OFFSET */ -} - -static __inline__ int -i2c_wait4bus (void) -{ - ulong timeval = get_timer (0); - while (readb(&i2c_dev->sr) & I2C_SR_MBB) { - if (get_timer (timeval) > I2C_TIMEOUT) { - return -1; - } - } - return 0; -} - -static __inline__ int -i2c_wait (int write) -{ - u32 csr; - ulong timeval = get_timer(0); - do { - csr = readb(&i2c_dev->sr); - - if (!(csr & I2C_SR_MIF)) - continue; - - writeb(0x0, &i2c_dev->sr); - - if (csr & I2C_SR_MAL) { - debug("i2c_wait: MAL\n"); - return -1; - } - - if (!(csr & I2C_SR_MCF)) { - debug("i2c_wait: unfinished\n"); - return -1; - } - - if (write == I2C_WRITE && (csr & I2C_SR_RXAK)) { - debug("i2c_wait: No RXACK\n"); - return -1; - } - - return 0; - } while (get_timer (timeval) < I2C_TIMEOUT); - - debug("i2c_wait: timed out\n"); - return -1; -} - -static __inline__ int -i2c_write_addr (u8 dev, u8 dir, int rsta) -{ - writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX | - (rsta?I2C_CR_RSTA:0), - &i2c_dev->cr); - - writeb((dev << 1) | dir, &i2c_dev->dr); - - if (i2c_wait (I2C_WRITE) < 0) - return 0; - return 1; -} - -static __inline__ int -__i2c_write (u8 *data, int length) -{ - int i; - - writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX, - &i2c_dev->cr); - - for (i=0; i < length; i++) { - writeb(data[i], &i2c_dev->dr); - - if (i2c_wait (I2C_WRITE) < 0) - break; - } - return i; -} - -static __inline__ int -__i2c_read (u8 *data, int length) -{ - int i; - - writeb(I2C_CR_MEN | I2C_CR_MSTA | - ((length == 1) ? I2C_CR_TXAK : 0), - &i2c_dev->cr); - - /* dummy read */ - readb(&i2c_dev->dr); - - for (i=0; i < length; i++) { - if (i2c_wait (I2C_READ) < 0) - break; - - /* Generate ack on last next to last byte */ - if (i == length - 2) - writeb(I2C_CR_MEN | I2C_CR_MSTA | - I2C_CR_TXAK, - &i2c_dev->cr); - - /* Generate stop on last byte */ - if (i == length - 1) - writeb(I2C_CR_MEN | I2C_CR_TXAK, &i2c_dev->cr); - - data[i] = readb(&i2c_dev->dr); - } - return i; -} - -int -i2c_read (u8 dev, uint addr, int alen, u8 *data, int length) -{ - int i = 0; - u8 *a = (u8*)&addr; - - if (i2c_wait4bus () < 0) - goto exit; - - if (i2c_write_addr (dev, I2C_WRITE, 0) == 0) - goto exit; - - if (__i2c_write (&a[4 - alen], alen) != alen) - goto exit; - - if (i2c_write_addr (dev, I2C_READ, 1) == 0) - goto exit; - - i = __i2c_read (data, length); - - exit: - writeb(I2C_CR_MEN, &i2c_dev->cr); - return !(i == length); -} - -int -i2c_write (u8 dev, uint addr, int alen, u8 *data, int length) -{ - int i = 0; - u8 *a = (u8*)&addr; - - if (i2c_wait4bus () < 0) - goto exit; - - if (i2c_write_addr (dev, I2C_WRITE, 0) == 0) - goto exit; - - if (__i2c_write (&a[4 - alen], alen) != alen) - goto exit; - - i = __i2c_write (data, length); - - exit: - writeb(I2C_CR_MEN, &i2c_dev->cr); - return !(i == length); -} - -int i2c_probe (uchar chip) -{ - int tmp; - - /* - * Try to read the first location of the chip. The underlying - * driver doesn't appear to support sending just the chip address - * and looking for an back. - */ - udelay(10000); - return i2c_read (chip, 0, 1, (uchar *)&tmp, 1); -} - -uchar i2c_reg_read (uchar i2c_addr, uchar reg) -{ - uchar buf[1]; - - i2c_read (i2c_addr, reg, 1, buf, 1); - - return (buf[0]); -} - -void i2c_reg_write (uchar i2c_addr, uchar reg, uchar val) -{ - i2c_write (i2c_addr, reg, 1, &val, 1); -} - -int i2c_set_bus_num(unsigned int bus) -{ - if(bus == 1) - { - i2c_dev = I2C_1; - } -#ifdef CFG_I2C2_OFFSET - else if(bus == 2) - { - i2c_dev = I2C_2; - } -#endif - else - { - return -1; - } - i2c_bus_num = bus; - return 0; -} - -int i2c_set_bus_speed(unsigned int speed) -{ - return set_speed(speed); -} - -unsigned int i2c_get_bus_num(void) -{ - return i2c_bus_num; -} - -unsigned int i2c_get_bus_speed(void) -{ - return i2c_bus_speed[i2c_bus_num - 1]; -} -#endif /* CONFIG_HARD_I2C */ diff --git a/drivers/fsl_i2c.c b/drivers/fsl_i2c.c index 65c27439e3..0e39213487 100644 --- a/drivers/fsl_i2c.c +++ b/drivers/fsl_i2c.c @@ -28,29 +28,49 @@ #include /* HW definitions */ #define I2C_TIMEOUT (CFG_HZ / 4) -#define I2C ((struct fsl_i2c *)(CFG_IMMR + CFG_I2C_OFFSET)) +/* Initialize the bus pointer to whatever one the SPD EEPROM is on. + * Default is bus 0. This is necessary because the DDR initialization + * runs from ROM, and we can't switch buses because we can't modify + * the global variables. + */ +#ifdef CFG_SPD_BUS_NUM +static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = CFG_SPD_BUS_NUM; +#else +static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = 0; +#endif + +static volatile struct fsl_i2c *i2c_dev[2] = { + (struct fsl_i2c *) (CFG_IMMR + CFG_I2C_OFFSET), +#ifdef CFG_I2C2_OFFSET + (struct fsl_i2c *) (CFG_IMMR + CFG_I2C2_OFFSET) +#endif +}; void i2c_init(int speed, int slaveadd) { - /* stop I2C controller */ - writeb(0x0, &I2C->cr); - - /* set clock */ - writeb(0x3f, &I2C->fdr); - - /* set default filter */ - writeb(0x10, &I2C->dfsrr); - - /* write slave address */ - writeb(slaveadd, &I2C->adr); - - /* clear status register */ - writeb(0x0, &I2C->sr); - - /* start I2C controller */ - writeb(I2C_CR_MEN, &I2C->cr); + volatile struct fsl_i2c *dev; + + dev = (struct fsl_i2c *) (CFG_IMMR + CFG_I2C_OFFSET); + + writeb(0, &dev->cr); /* stop I2C controller */ + writeb(0x3F, &dev->fdr); /* set bus speed */ + writeb(0x3F, &dev->dfsrr); /* set default filter */ + writeb(slaveadd, &dev->adr); /* write slave address */ + writeb(0x0, &dev->sr); /* clear status register */ + writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */ + +#ifdef CFG_I2C2_OFFSET + dev = (struct fsl_i2c *) (CFG_IMMR + CFG_I2C2_OFFSET); + + writeb(0, &dev->cr); /* stop I2C controller */ + writeb(0x3F, &dev->fdr); /* set bus speed */ + writeb(0x3F, &dev->dfsrr); /* set default filter */ + writeb(slaveadd, &dev->adr); /* write slave address */ + writeb(0x0, &dev->sr); /* clear status register */ + writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */ +#endif /* CFG_I2C2_OFFSET */ } static __inline__ int @@ -58,7 +78,7 @@ i2c_wait4bus(void) { ulong timeval = get_timer(0); - while (readb(&I2C->sr) & I2C_SR_MBB) { + while (readb(&i2c_dev[i2c_bus_num]->sr) & I2C_SR_MBB) { if (get_timer(timeval) > I2C_TIMEOUT) { return -1; } @@ -74,11 +94,11 @@ i2c_wait(int write) ulong timeval = get_timer(0); do { - csr = readb(&I2C->sr); + csr = readb(&i2c_dev[i2c_bus_num]->sr); if (!(csr & I2C_SR_MIF)) continue; - writeb(0x0, &I2C->sr); + writeb(0x0, &i2c_dev[i2c_bus_num]->sr); if (csr & I2C_SR_MAL) { debug("i2c_wait: MAL\n"); @@ -107,9 +127,9 @@ i2c_write_addr (u8 dev, u8 dir, int rsta) { writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX | (rsta ? I2C_CR_RSTA : 0), - &I2C->cr); + &i2c_dev[i2c_bus_num]->cr); - writeb((dev << 1) | dir, &I2C->dr); + writeb((dev << 1) | dir, &i2c_dev[i2c_bus_num]->dr); if (i2c_wait(I2C_WRITE) < 0) return 0; @@ -123,10 +143,10 @@ __i2c_write(u8 *data, int length) int i; writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX, - &I2C->cr); + &i2c_dev[i2c_bus_num]->cr); for (i = 0; i < length; i++) { - writeb(data[i], &I2C->dr); + writeb(data[i], &i2c_dev[i2c_bus_num]->dr); if (i2c_wait(I2C_WRITE) < 0) break; @@ -141,10 +161,10 @@ __i2c_read(u8 *data, int length) int i; writeb(I2C_CR_MEN | I2C_CR_MSTA | ((length == 1) ? I2C_CR_TXAK : 0), - &I2C->cr); + &i2c_dev[i2c_bus_num]->cr); /* dummy read */ - readb(&I2C->dr); + readb(&i2c_dev[i2c_bus_num]->dr); for (i = 0; i < length; i++) { if (i2c_wait(I2C_READ) < 0) @@ -153,13 +173,13 @@ __i2c_read(u8 *data, int length) /* Generate ack on last next to last byte */ if (i == length - 2) writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_TXAK, - &I2C->cr); + &i2c_dev[i2c_bus_num]->cr); /* Generate stop on last byte */ if (i == length - 1) - writeb(I2C_CR_MEN | I2C_CR_TXAK, &I2C->cr); + writeb(I2C_CR_MEN | I2C_CR_TXAK, &i2c_dev[i2c_bus_num]->cr); - data[i] = readb(&I2C->dr); + data[i] = readb(&i2c_dev[i2c_bus_num]->dr); } return i; @@ -178,7 +198,7 @@ i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) i = __i2c_read(data, length); } - writeb(I2C_CR_MEN, &I2C->cr); + writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); if (i == length) return 0; @@ -198,7 +218,7 @@ i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) i = __i2c_write(data, length); } - writeb(I2C_CR_MEN, &I2C->cr); + writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); if (i == length) return 0; @@ -237,5 +257,34 @@ i2c_reg_write(uchar i2c_addr, uchar reg, uchar val) i2c_write(i2c_addr, reg, 1, &val, 1); } +int i2c_set_bus_num(unsigned int bus) +{ +#ifdef CFG_I2C2_OFFSET + if (bus > 1) { +#else + if (bus > 0) { +#endif + return -1; + } + + i2c_bus_num = bus; + + return 0; +} + +int i2c_set_bus_speed(unsigned int speed) +{ + return -1; +} + +unsigned int i2c_get_bus_num(void) +{ + return i2c_bus_num; +} + +unsigned int i2c_get_bus_speed(void) +{ + return 0; +} #endif /* CONFIG_HARD_I2C */ #endif /* CONFIG_FSL_I2C */ diff --git a/include/asm-ppc/i2c.h b/include/asm-ppc/i2c.h deleted file mode 100644 index 37847666db..0000000000 --- a/include/asm-ppc/i2c.h +++ /dev/null @@ -1,100 +0,0 @@ -/* - * Freescale I2C Controller - * - * This software may be used and distributed according to the - * terms of the GNU Public License, Version 2, incorporated - * herein by reference. - * - * Copyright 2004 Freescale Semiconductor. - * (C) Copyright 2003, Motorola, Inc. - * author: Eran Liberty (liberty@freescale.com) - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef _ASM_I2C_H_ -#define _ASM_I2C_H_ - -#include - -typedef struct i2c -{ - u8 adr; /**< I2C slave address */ -#define I2C_ADR 0xFE -#define I2C_ADR_SHIFT 1 -#define I2C_ADR_RES ~(I2C_ADR) - u8 res0[3]; - u8 fdr; /**< I2C frequency divider register */ -#define IC2_FDR 0x3F -#define IC2_FDR_SHIFT 0 -#define IC2_FDR_RES ~(IC2_FDR) - u8 res1[3]; - u8 cr; /**< I2C control redister */ -#define I2C_CR_MEN 0x80 -#define I2C_CR_MIEN 0x40 -#define I2C_CR_MSTA 0x20 -#define I2C_CR_MTX 0x10 -#define I2C_CR_TXAK 0x08 -#define I2C_CR_RSTA 0x04 -#define I2C_CR_BCST 0x01 - u8 res2[3]; - u8 sr; /**< I2C status register */ -#define I2C_SR_MCF 0x80 -#define I2C_SR_MAAS 0x40 -#define I2C_SR_MBB 0x20 -#define I2C_SR_MAL 0x10 -#define I2C_SR_BCSTM 0x08 -#define I2C_SR_SRW 0x04 -#define I2C_SR_MIF 0x02 -#define I2C_SR_RXAK 0x01 - u8 res3[3]; - u8 dr; /**< I2C data register */ -#define I2C_DR 0xFF -#define I2C_DR_SHIFT 0 -#define I2C_DR_RES ~(I2C_DR) - u8 res4[3]; - u8 dfsrr; /**< I2C digital filter sampling rate register */ -#define I2C_DFSRR 0x3F -#define I2C_DFSRR_SHIFT 0 -#define I2C_DFSRR_RES ~(I2C_DR) - u8 res5[3]; - u8 res6[0xE8]; -} i2c_t; - -#ifndef CFG_HZ -#error CFG_HZ is not defined in /include/configs/${BOARD}.h -#endif -#define I2C_TIMEOUT (CFG_HZ/4) - -#ifndef CFG_IMMR -#error CFG_IMMR is not defined in /include/configs/${BOARD}.h -#endif - -#ifndef CFG_I2C_OFFSET -#error CFG_I2C_OFFSET is not defined in /include/configs/${BOARD}.h -#endif - -#define I2C_1 ((i2c_t*)(CFG_IMMR + CFG_I2C_OFFSET)) - -/* Optional support for second I2C bus */ -#ifdef CFG_I2C2_OFFSET -#define I2C_2 ((i2c_t*)(CFG_IMMR + CFG_I2C2_OFFSET)) -#endif /* CFG_I2C2_OFFSET */ - -#define I2C_READ 1 -#define I2C_WRITE 0 - -#endif /* _ASM_I2C_H_ */ diff --git a/include/asm-ppc/immap_83xx.h b/include/asm-ppc/immap_83xx.h index 09e08ba0a4..2a76a05c6c 100644 --- a/include/asm-ppc/immap_83xx.h +++ b/include/asm-ppc/immap_83xx.h @@ -39,7 +39,7 @@ #include #include -#include +#include /* * Local Access Window. @@ -2007,7 +2007,7 @@ typedef struct immap { qesba83xx_t qesba; /* QE Secondary Bus Access Windows */ #endif ddr83xx_t ddr; /* DDR Memory Controller Memory */ - i2c_t i2c[2]; /* I2C1 Controller */ + fsl_i2c_t i2c[2]; /* I2C Controllers */ u8 res2[0x1300]; duart83xx_t duart[2]; /* DUART */ #if defined (CONFIG_MPC8349) diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h index 4a5b4bc4a7..5bed2d0a29 100644 --- a/include/configs/MPC8349EMDS.h +++ b/include/configs/MPC8349EMDS.h @@ -335,6 +335,7 @@ /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_FSL_I2C #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index c74e63a4d4..8dc96352a1 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -41,14 +41,14 @@ Align. Board Bus Addr Part No. Description Length Location ---------------------------------------------------------------- - I2C1 0x50 M24256-BWMN6P Board EEPROM 2 U64 + I2C0 0x50 M24256-BWMN6P Board EEPROM 2 U64 - I2C2 0x20 PCF8574 I2C Expander 0 U8 - I2C2 0x21 PCF8574 I2C Expander 0 U10 - I2C2 0x38 PCF8574A I2C Expander 0 U8 - I2C2 0x39 PCF8574A I2C Expander 0 U10 - I2C2 0x51 (DDR) DDR EEPROM 1 U1 - I2C2 0x68 DS1339 RTC 1 U68 + I2C1 0x20 PCF8574 I2C Expander 0 U8 + I2C1 0x21 PCF8574 I2C Expander 0 U10 + I2C1 0x38 PCF8574A I2C Expander 0 U8 + I2C1 0x39 PCF8574A I2C Expander 0 U10 + I2C1 0x51 (DDR) DDR EEPROM 1 U1 + I2C1 0x68 DS1339 RTC 1 U68 Note that a given board has *either* a pair of 8574s or a pair of 8574As. */ @@ -77,19 +77,20 @@ #define CONFIG_MISC_INIT_F #define CONFIG_MISC_INIT_R +#define CONFIG_FSL_I2C #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE #define CFG_I2C_OFFSET 0x3000 #define CFG_I2C2_OFFSET 0x3100 -#define CFG_SPD_BUS_NUM 2 +#define CFG_SPD_BUS_NUM 1 /* The I2C bus for SPD */ -#define CFG_I2C_8574_ADDR1 0x20 /* I2C2, PCF8574 */ -#define CFG_I2C_8574_ADDR2 0x21 /* I2C2, PCF8574 */ -#define CFG_I2C_8574A_ADDR1 0x38 /* I2C2, PCF8574A */ -#define CFG_I2C_8574A_ADDR2 0x39 /* I2C2, PCF8574A */ -#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C1, Board EEPROM */ -#define CFG_I2C_RTC_ADDR 0x68 /* I2C2, DS1339 RTC*/ -#define SPD_EEPROM_ADDRESS 0x51 /* I2C2, DDR */ +#define CFG_I2C_8574_ADDR1 0x20 /* I2C1, PCF8574 */ +#define CFG_I2C_8574_ADDR2 0x21 /* I2C1, PCF8574 */ +#define CFG_I2C_8574A_ADDR1 0x38 /* I2C1, PCF8574A */ +#define CFG_I2C_8574A_ADDR2 0x39 /* I2C1, PCF8574A */ +#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C0, Board EEPROM */ +#define CFG_I2C_RTC_ADDR 0x68 /* I2C1, DS1339 RTC*/ +#define SPD_EEPROM_ADDRESS 0x51 /* I2C1, DDR */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F @@ -175,6 +176,7 @@ #define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ #define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */ #define CFG_FLASH_SIZE 16 /* FLASH size in MB */ +#define CFG_FLASH_EMPTY_INFO #define CFG_BR0_PRELIM (CFG_FLASH_BASE | BR_PS_16 | BR_V) #define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ @@ -610,7 +612,7 @@ #define CFG_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */ #define CFG_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */ #define CFG_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */ -#define CFG_SCCR_TSEC2CM 1 /* TSEC2 & I2C1 clock mode (0-3) */ +#define CFG_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */ #define CFG_ACR_RPTCNT 3 /* Arbiter repeat count */ /* System IO Config */ @@ -708,6 +710,19 @@ #define CONFIG_ETH1ADDR 00:E0:0C:00:8C:02 #endif +#if 1 +#define CONFIG_IPADDR 10.82.19.159 +#define CONFIG_SERVERIP 10.82.48.106 +#define CONFIG_GATEWAYIP 10.82.19.254 +#define CONFIG_NETMASK 255.255.252.0 +#define CONFIG_NETDEV eth0 + +#define CONFIG_HOSTNAME mpc8349emitx +#define CONFIG_ROOTPATH /nfsroot0/u/timur/itx-ltib/rootfs +#define CONFIG_BOOTFILE timur/uImage + +#define CONFIG_UBOOTPATH timur/u-boot.bin +#else #define CONFIG_IPADDR 192.168.1.253 #define CONFIG_SERVERIP 192.168.1.1 #define CONFIG_GATEWAYIP 192.168.1.1 @@ -719,6 +734,8 @@ #define CONFIG_BOOTFILE uImage #define CONFIG_UBOOTPATH u-boot.bin +#endif + #define CONFIG_UBOOTSTART fe700000 #define CONFIG_UBOOTEND fe77ffff diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index a8f2df911e..2ff5f48980 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -330,7 +330,8 @@ /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 0x3F /* I2C speed and slave address */ +#define CONFIG_FSL_I2C +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES {0x52} /* Don't probe these addrs */ #define CFG_I2C_OFFSET 0x3000 diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h index b0b0673cff..728083b304 100644 --- a/include/configs/TQM834x.h +++ b/include/configs/TQM834x.h @@ -218,6 +218,7 @@ extern int tqm834x_num_flash_banks; */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_FSL_I2C #define CFG_I2C_SPEED 400000 /* I2C speed: 400KHz */ #define CFG_I2C_SLAVE 0x7F /* slave address */ #define CFG_I2C_OFFSET 0x3000