From: Albert ARIBAUD <albert.u.boot@aribaud.net>
Date: Sat, 11 May 2013 20:24:28 +0000 (+0200)
Subject: Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
X-Git-Tag: v2013.07-rc1~83
X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=cac423a730d3506154744485af1bbc1cd3a1e6a8;hp=c1b43ac7699640c8086bd73faa798bc9722d32c9;p=u-boot

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
---

diff --git a/MAINTAINERS b/MAINTAINERS
index 7c12d955aa..c05433a7a7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -607,6 +607,7 @@ Enric Balletbo i Serra <eballetbo@iseebcn.com>
 	igep0020	ARM ARMV7 (OMAP3xx SoC)
 	igep0030	ARM ARMV7 (OMAP3xx SoC)
 	igep0032	ARM ARMV7 (OMAP3xx SoC)
+	igep0033	ARM ARMV7 (AM33xx Soc)
 
 Eric Benard <eric@eukrea.com>
 
@@ -684,7 +685,7 @@ Simon Guinot <simon.guinot@sequanux.org>
 
 Igor Grinberg <grinberg@compulab.co.il>
 
-	cm-t35		ARM ARMV7 (OMAP3xx Soc)
+	cm_t35		ARM ARMV7 (OMAP3xx Soc)
 
 Stefan Herbrechtsmeier <stefan@code.herbrechtsmeier.net>
 
diff --git a/README b/README
index bab1a95d20..b72ab2fb82 100644
--- a/README
+++ b/README
@@ -3340,6 +3340,10 @@ Configuration Settings:
 	offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
 	directly. You should not need to touch this setting.
 
+- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
+	This is set by OMAP boards for the max time that reset should
+	be asserted. See doc/README.omap-reset-time for details on how
+	the value can be calulated on a given board.
 
 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
diff --git a/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c b/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c
index ff2e2e33df..127beb86bc 100644
--- a/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c
+++ b/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c
@@ -32,6 +32,14 @@
 #include <asm/arch/emif_defs.h>
 #include <asm/arch/pll_defs.h>
 
+void davinci_enable_uart0(void)
+{
+	lpsc_on(DAVINCI_LPSC_UART0);
+
+	/* Bringup UART0 out of reset */
+	REG(UART0_PWREMU_MGMT) = 0x00006001;
+}
+
 #if defined(CONFIG_SYS_DA850_PLL_INIT)
 void da850_waitloop(unsigned long loopcnt)
 {
diff --git a/arch/arm/cpu/armv7/am33xx/clock_ti814x.c b/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
index cb4210f6e6..8b2878d4ff 100644
--- a/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
+++ b/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
@@ -109,6 +109,8 @@ struct ad_pll {
 #define OSC_SRC_CTRL			(PLL_SUBSYS_BASE + 0x2C0)
 
 /* PRCM */
+#define ENET_CLKCTRL_CMPL		0x30000
+
 #define CM_DEFAULT_BASE			(PRCM_BASE + 0x0500)
 
 struct cm_def {
@@ -183,7 +185,7 @@ struct cm_alwon {
 	unsigned int resv5[2];
 	unsigned int gpmcclkctrl;
 	unsigned int ethernet0clkctrl;
-	unsigned int resv6[1];
+	unsigned int ethernet1clkctrl;
 	unsigned int mpuclkctrl;
 	unsigned int debugssclkctrl;
 	unsigned int l3clkctrl;
@@ -203,9 +205,67 @@ struct cm_alwon {
 	unsigned int custefuseclkctrl;
 };
 
+#define SATA_PLL_BASE			(CTRL_BASE + 0x0720)
+
+struct sata_pll {
+	unsigned int pllcfg0;
+	unsigned int pllcfg1;
+	unsigned int pllcfg2;
+	unsigned int pllcfg3;
+	unsigned int pllcfg4;
+	unsigned int pllstatus;
+	unsigned int rxstatus;
+	unsigned int txstatus;
+	unsigned int testcfg;
+};
+
+#define SEL_IN_FREQ		(0x1 << 31)
+#define DIGCLRZ			(0x1 << 30)
+#define ENDIGLDO		(0x1 << 4)
+#define APLL_CP_CURR		(0x1 << 3)
+#define ENBGSC_REF		(0x1 << 2)
+#define ENPLLLDO		(0x1 << 1)
+#define ENPLL			(0x1 << 0)
+
+#define SATA_PLLCFG0_1 (SEL_IN_FREQ | ENBGSC_REF)
+#define SATA_PLLCFG0_2 (SEL_IN_FREQ | ENDIGLDO | ENBGSC_REF)
+#define SATA_PLLCFG0_3 (SEL_IN_FREQ | ENDIGLDO | ENBGSC_REF | ENPLLLDO)
+#define SATA_PLLCFG0_4 (SEL_IN_FREQ | DIGCLRZ | ENDIGLDO | ENBGSC_REF | \
+			ENPLLLDO | ENPLL)
+
+#define PLL_LOCK		(0x1 << 0)
+
+#define ENSATAMODE		(0x1 << 31)
+#define PLLREFSEL		(0x1 << 30)
+#define MDIVINT			(0x4b << 18)
+#define EN_CLKAUX		(0x1 << 5)
+#define EN_CLK125M		(0x1 << 4)
+#define EN_CLK100M		(0x1 << 3)
+#define EN_CLK50M		(0x1 << 2)
+
+#define SATA_PLLCFG1 (ENSATAMODE |	\
+		      PLLREFSEL |	\
+		      MDIVINT |		\
+		      EN_CLKAUX |	\
+		      EN_CLK125M |	\
+		      EN_CLK100M |	\
+		      EN_CLK50M)
+
+#define DIGLDO_EN_CAPLESSMODE	(0x1 << 22)
+#define PLLDO_EN_LDO_STABLE	(0x1 << 11)
+#define PLLDO_EN_BUF_CUR	(0x1 << 7)
+#define PLLDO_EN_LP		(0x1 << 6)
+#define PLLDO_CTRL_TRIM_1_4V	(0x10 << 1)
+
+#define SATA_PLLCFG3 (DIGLDO_EN_CAPLESSMODE |	\
+		      PLLDO_EN_LDO_STABLE |	\
+		      PLLDO_EN_BUF_CUR |	\
+		      PLLDO_EN_LP |		\
+		      PLLDO_CTRL_TRIM_1_4V)
 
 const struct cm_alwon *cmalwon = (struct cm_alwon *)CM_ALWON_BASE;
 const struct cm_def *cmdef = (struct cm_def *)CM_DEFAULT_BASE;
+const struct sata_pll *spll = (struct sata_pll *)SATA_PLL_BASE;
 
 /*
  * Enable the peripheral clock for required peripherals
@@ -221,6 +281,15 @@ static void enable_per_clocks(void)
 	writel(PRCM_MOD_EN, &cmalwon->mmchs1clkctrl);
 	while (readl(&cmalwon->mmchs1clkctrl) != PRCM_MOD_EN)
 		;
+
+	/* Ethernet */
+	writel(PRCM_MOD_EN, &cmalwon->ethclkstctrl);
+	writel(PRCM_MOD_EN, &cmalwon->ethernet0clkctrl);
+	while ((readl(&cmalwon->ethernet0clkctrl) & ENET_CLKCTRL_CMPL) != 0)
+		;
+	writel(PRCM_MOD_EN, &cmalwon->ethernet1clkctrl);
+	while ((readl(&cmalwon->ethernet1clkctrl) & ENET_CLKCTRL_CMPL) != 0)
+		;
 }
 
 /*
@@ -365,6 +434,35 @@ void ddr_pll_config(unsigned int ddrpll_m)
 	pll_config(DDR_PLL_BASE, DDR_N, DDR_M, DDR_M2, DDR_CLKCTRL, 1);
 }
 
+void sata_pll_config(void)
+{
+	/*
+	 * This sequence for configuring the SATA PLL
+	 * resident in the control module is documented
+	 * in TI8148 TRM section 21.3.1
+	 */
+	writel(SATA_PLLCFG1, &spll->pllcfg1);
+	udelay(50);
+
+	writel(SATA_PLLCFG3, &spll->pllcfg3);
+	udelay(50);
+
+	writel(SATA_PLLCFG0_1, &spll->pllcfg0);
+	udelay(50);
+
+	writel(SATA_PLLCFG0_2, &spll->pllcfg0);
+	udelay(50);
+
+	writel(SATA_PLLCFG0_3, &spll->pllcfg0);
+	udelay(50);
+
+	writel(SATA_PLLCFG0_4, &spll->pllcfg0);
+	udelay(50);
+
+	while (((readl(&spll->pllstatus) & PLL_LOCK) == 0))
+		;
+}
+
 void enable_emif_clocks(void) {};
 
 void enable_dmm_clocks(void)
@@ -397,9 +495,10 @@ void pll_init()
 	/* Enable the control module */
 	writel(PRCM_MOD_EN, &cmalwon->controlclkctrl);
 
+	/* Configure PLLs */
 	mpu_pll_config();
-
 	l3_pll_config();
+	sata_pll_config();
 
 	/* Enable the required peripherals */
 	enable_per_clocks();
diff --git a/arch/arm/cpu/armv7/am33xx/sys_info.c b/arch/arm/cpu/armv7/am33xx/sys_info.c
index 5fd8b47b2d..ac049ac4f2 100644
--- a/arch/arm/cpu/armv7/am33xx/sys_info.c
+++ b/arch/arm/cpu/armv7/am33xx/sys_info.c
@@ -92,7 +92,6 @@ u32 get_sysboot_value(void)
 int print_cpuinfo(void)
 {
 	char *cpu_s, *sec_s;
-	int arm_freq, ddr_freq;
 
 	switch (get_cpu_type()) {
 	case AM335X:
@@ -123,10 +122,7 @@ int print_cpuinfo(void)
 		sec_s = "?";
 	}
 
-	printf("%s-%s rev %d\n",
-			cpu_s, sec_s, get_cpu_rev());
-
-	/* TODO: Print ARM and DDR frequencies  */
+	printf("%s-%s rev %d\n", cpu_s, sec_s, get_cpu_rev());
 
 	return 0;
 }
diff --git a/arch/arm/cpu/armv7/lowlevel_init.S b/arch/arm/cpu/armv7/lowlevel_init.S
index 0d45528e99..0a15aa4671 100644
--- a/arch/arm/cpu/armv7/lowlevel_init.S
+++ b/arch/arm/cpu/armv7/lowlevel_init.S
@@ -37,7 +37,13 @@ ENTRY(lowlevel_init)
 	 */
 	ldr	sp, =CONFIG_SYS_INIT_SP_ADDR
 	bic	sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
+#ifdef CONFIG_SPL_BUILD
+	ldr	r8, =gdata
+#else
+	sub	sp, #GD_SIZE
+	bic	sp, sp, #7
+	mov	r8, sp
+#endif
 	/*
 	 * Save the old lr(passed in ip) and the current lr to stack
 	 */
diff --git a/arch/arm/cpu/armv7/omap-common/boot-common.c b/arch/arm/cpu/armv7/omap-common/boot-common.c
index 24cbe2da05..bff7e9c82a 100644
--- a/arch/arm/cpu/armv7/omap-common/boot-common.c
+++ b/arch/arm/cpu/armv7/omap-common/boot-common.c
@@ -23,31 +23,17 @@
 #include <asm/arch/mmc_host_def.h>
 #include <asm/arch/sys_proto.h>
 
-/*
- * This is used to verify if the configuration header
- * was executed by rom code prior to control of transfer
- * to the bootloader. SPL is responsible for saving and
- * passing the boot_params pointer to the u-boot.
- */
-struct omap_boot_parameters boot_params __attribute__ ((section(".data")));
+DECLARE_GLOBAL_DATA_PTR;
 
 #ifdef CONFIG_SPL_BUILD
-/*
- * We use static variables because global data is not ready yet.
- * Initialized data is available in SPL right from the beginning.
- * We would not typically need to save these parameters in regular
- * U-Boot. This is needed only in SPL at the moment.
- */
-u32 omap_bootmode = MMCSD_MODE_FAT;
-
 u32 spl_boot_device(void)
 {
-	return (u32) (boot_params.omap_bootdevice);
+	return (u32) (gd->arch.omap_boot_params.omap_bootdevice);
 }
 
 u32 spl_boot_mode(void)
 {
-	return omap_bootmode;
+	return gd->arch.omap_boot_params.omap_bootmode;
 }
 
 void spl_board_init(void)
@@ -73,4 +59,15 @@ int board_mmc_init(bd_t *bis)
 	}
 	return 0;
 }
+
+void __noreturn jump_to_image_no_args(struct spl_image_info *spl_image)
+{
+	typedef void __noreturn (*image_entry_noargs_t)(u32 *);
+	image_entry_noargs_t image_entry =
+			(image_entry_noargs_t) spl_image->entry_point;
+
+	debug("image entry point: 0x%X\n", spl_image->entry_point);
+	/* Pass the saved boot_params from rom code */
+	image_entry((u32 *)&gd->arch.omap_boot_params);
+}
 #endif
diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c
index 2b955c7c00..99910cdcb0 100644
--- a/arch/arm/cpu/armv7/omap-common/clocks-common.c
+++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c
@@ -716,6 +716,7 @@ void prcm_init(void)
 		setup_non_essential_dplls();
 		enable_non_essential_clocks();
 #endif
+		setup_warmreset_time();
 		break;
 	default:
 		break;
diff --git a/arch/arm/cpu/armv7/omap-common/emif-common.c b/arch/arm/cpu/armv7/omap-common/emif-common.c
index cdb4439721..11e830a533 100644
--- a/arch/arm/cpu/armv7/omap-common/emif-common.c
+++ b/arch/arm/cpu/armv7/omap-common/emif-common.c
@@ -1075,6 +1075,11 @@ static void do_sdram_init(u32 base)
 		else
 			ddr3_init(base, regs);
 	}
+	if (warm_reset() && (emif_sdram_type() == EMIF_SDRAM_TYPE_DDR3)) {
+		set_lpmode_selfrefresh(base);
+		emif_reset_phy(base);
+		ddr3_leveling(base, regs);
+	}
 
 	/* Write to the shadow registers */
 	emif_update_timings(base, regs);
@@ -1262,10 +1267,10 @@ void sdram_init(void)
 	in_sdram = running_from_sdram();
 	debug("in_sdram = %d\n", in_sdram);
 
-	if (!(in_sdram || warm_reset())) {
-		if (sdram_type == EMIF_SDRAM_TYPE_LPDDR2)
+	if (!in_sdram) {
+		if ((sdram_type == EMIF_SDRAM_TYPE_LPDDR2) && !warm_reset())
 			bypass_dpll((*prcm)->cm_clkmode_dpll_core);
-		else
+		else if (sdram_type == EMIF_SDRAM_TYPE_DDR3)
 			writel(CM_DLL_CTRL_NO_OVERRIDE, (*prcm)->cm_dll_ctrl);
 	}
 
diff --git a/arch/arm/cpu/armv7/omap-common/hwinit-common.c b/arch/arm/cpu/armv7/omap-common/hwinit-common.c
index 70d16a8160..1645120de7 100644
--- a/arch/arm/cpu/armv7/omap-common/hwinit-common.c
+++ b/arch/arm/cpu/armv7/omap-common/hwinit-common.c
@@ -101,11 +101,6 @@ void omap_rev_string(void)
 }
 
 #ifdef CONFIG_SPL_BUILD
-static void init_boot_params(void)
-{
-	boot_params_ptr = (u32 *) &boot_params;
-}
-
 void spl_display_print(void)
 {
 	omap_rev_string();
@@ -116,6 +111,53 @@ void __weak srcomp_enable(void)
 {
 }
 
+static void save_omap_boot_params(void)
+{
+	u32 rom_params = *((u32 *)OMAP_SRAM_SCRATCH_BOOT_PARAMS);
+	u8 boot_device;
+	u32 dev_desc, dev_data;
+
+	if ((rom_params <  NON_SECURE_SRAM_START) ||
+	    (rom_params > NON_SECURE_SRAM_END))
+		return;
+
+	/*
+	 * rom_params can be type casted to omap_boot_parameters and
+	 * used. But it not correct to assume that romcode structure
+	 * encoding would be same as u-boot. So use the defined offsets.
+	 */
+	gd->arch.omap_boot_params.omap_bootdevice = boot_device =
+				   *((u8 *)(rom_params + BOOT_DEVICE_OFFSET));
+
+	gd->arch.omap_boot_params.ch_flags =
+				*((u8 *)(rom_params + CH_FLAGS_OFFSET));
+
+	if ((boot_device >= MMC_BOOT_DEVICES_START) &&
+	    (boot_device <= MMC_BOOT_DEVICES_END)) {
+		if ((omap_hw_init_context() ==
+				      OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL)) {
+			gd->arch.omap_boot_params.omap_bootmode =
+			*((u8 *)(rom_params + BOOT_MODE_OFFSET));
+		} else {
+			dev_desc = *((u32 *)(rom_params + DEV_DESC_PTR_OFFSET));
+			dev_data = *((u32 *)(dev_desc + DEV_DATA_PTR_OFFSET));
+			gd->arch.omap_boot_params.omap_bootmode =
+					*((u32 *)(dev_data + BOOT_MODE_OFFSET));
+		}
+	}
+}
+
+#ifdef CONFIG_ARCH_CPU_INIT
+/*
+ * SOC specific cpu init
+ */
+int arch_cpu_init(void)
+{
+	save_omap_boot_params();
+	return 0;
+}
+#endif /* CONFIG_ARCH_CPU_INIT */
+
 /*
  * Routine: s_init
  * Description: Does early system init of watchdog, muxing,  andclocks
@@ -132,6 +174,14 @@ void __weak srcomp_enable(void)
  */
 void s_init(void)
 {
+	/*
+	 * Save the boot parameters passed from romcode.
+	 * We cannot delay the saving further than this,
+	 * to prevent overwrites.
+	 */
+#ifdef CONFIG_SPL_BUILD
+	save_omap_boot_params();
+#endif
 	init_omap_revision();
 	hw_data_init();
 
@@ -156,7 +206,6 @@ void s_init(void)
 
 	/* For regular u-boot sdram_init() is called from dram_init() */
 	sdram_init();
-	init_boot_params();
 #endif
 }
 
diff --git a/arch/arm/cpu/armv7/omap-common/lowlevel_init.S b/arch/arm/cpu/armv7/omap-common/lowlevel_init.S
index 90b3c8aea4..c4895369bf 100644
--- a/arch/arm/cpu/armv7/omap-common/lowlevel_init.S
+++ b/arch/arm/cpu/armv7/omap-common/lowlevel_init.S
@@ -28,59 +28,13 @@
 
 #include <config.h>
 #include <asm/arch/omap.h>
+#include <asm/omap_common.h>
 #include <asm/arch/spl.h>
 #include <linux/linkage.h>
 
 ENTRY(save_boot_params)
-	/*
-	 * See if the rom code passed pointer is valid:
-	 * It is not valid if it is not in non-secure SRAM
-	 * This may happen if you are booting with the help of
-	 * debugger
-	 */
-	ldr     r2, =NON_SECURE_SRAM_START
-	cmp	r2, r0
-	bgt	1f
-	ldr	r2, =NON_SECURE_SRAM_END
-	cmp	r2, r0
-	blt	1f
-
-	/*
-	 * store the boot params passed from rom code or saved
-	 * and passed by SPL
-	 */
-	cmp	r0, #0
-	beq	1f
-	ldr	r1, =boot_params
+	ldr	r1, =OMAP_SRAM_SCRATCH_BOOT_PARAMS
 	str	r0, [r1]
-#ifdef CONFIG_SPL_BUILD
-	/* Store the boot device in spl_boot_device */
-	ldrb	r2, [r0, #BOOT_DEVICE_OFFSET]	@ r1 <- value of boot device
-	and	r2, #BOOT_DEVICE_MASK
-	ldr	r3, =boot_params
-	strb	r2, [r3, #BOOT_DEVICE_OFFSET]	@ spl_boot_device <- r1
-
-	/*
-	 * boot mode is only valid for device that can be raw or FAT booted.
-	 * in other cases it may be fatal to look.  While platforms differ
-	 * in the values used for each MMC slot, they are contiguous.
-	 */
-	cmp	r2, #MMC_BOOT_DEVICES_START
-	blt	2f
-	cmp	r2, #MMC_BOOT_DEVICES_END
-	bgt	2f
-	/* Store the boot mode (raw/FAT) in omap_bootmode */
-	ldr	r2, [r0, #DEV_DESC_PTR_OFFSET]	@ get the device descriptor ptr
-	ldr	r2, [r2, #DEV_DATA_PTR_OFFSET]	@ get the pDeviceData ptr
-	ldr	r2, [r2, #BOOT_MODE_OFFSET]	@ get the boot mode
-	ldr	r3, =omap_bootmode
-	str	r2, [r3]
-#endif
-2:
-	ldrb	r2, [r0, #CH_FLAGS_OFFSET]
-	ldr	r3, =boot_params
-	strb	r2, [r3, #CH_FLAGS_OFFSET]
-1:
 	bx	lr
 ENDPROC(save_boot_params)
 
diff --git a/arch/arm/cpu/armv7/omap-common/reset.c b/arch/arm/cpu/armv7/omap-common/reset.c
index 587bb47745..57ea9d9999 100644
--- a/arch/arm/cpu/armv7/omap-common/reset.c
+++ b/arch/arm/cpu/armv7/omap-common/reset.c
@@ -39,3 +39,7 @@ u32 __weak warm_reset(void)
 {
 	return (readl(PRM_RSTST) & PRM_RSTST_WARM_RESET_MASK);
 }
+
+void __weak setup_warmreset_time(void)
+{
+}
diff --git a/arch/arm/cpu/armv7/omap4/emif.c b/arch/arm/cpu/armv7/omap4/emif.c
index 53f60635b1..0ddf35f79b 100644
--- a/arch/arm/cpu/armv7/omap4/emif.c
+++ b/arch/arm/cpu/armv7/omap4/emif.c
@@ -31,8 +31,8 @@
 #include <asm/utils.h>
 
 #ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
-u32 *const T_num = (u32 *)OMAP4_SRAM_SCRATCH_EMIF_T_NUM;
-u32 *const T_den = (u32 *)OMAP4_SRAM_SCRATCH_EMIF_T_DEN;
+u32 *const T_num = (u32 *)OMAP_SRAM_SCRATCH_EMIF_T_NUM;
+u32 *const T_den = (u32 *)OMAP_SRAM_SCRATCH_EMIF_T_DEN;
 #endif
 
 #ifdef CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
diff --git a/arch/arm/cpu/armv7/omap4/hw_data.c b/arch/arm/cpu/armv7/omap4/hw_data.c
index 04977b4f2b..06a2fc8c2f 100644
--- a/arch/arm/cpu/armv7/omap4/hw_data.c
+++ b/arch/arm/cpu/armv7/omap4/hw_data.c
@@ -40,7 +40,7 @@ struct dplls const **dplls_data =
 struct vcores_data const **omap_vcores =
 		(struct vcores_data const **) OMAP_SRAM_SCRATCH_VCORES_PTR;
 struct omap_sys_ctrl_regs const **ctrl =
-	(struct omap_sys_ctrl_regs const **)OMAP4_SRAM_SCRATCH_SYS_CTRL;
+	(struct omap_sys_ctrl_regs const **)OMAP_SRAM_SCRATCH_SYS_CTRL;
 
 /*
  * The M & N values in the following tables are created using the
diff --git a/arch/arm/cpu/armv7/omap4/hwinit.c b/arch/arm/cpu/armv7/omap4/hwinit.c
index 2db517b1bf..81f5a48e50 100644
--- a/arch/arm/cpu/armv7/omap4/hwinit.c
+++ b/arch/arm/cpu/armv7/omap4/hwinit.c
@@ -34,10 +34,11 @@
 #include <asm/sizes.h>
 #include <asm/emif.h>
 #include <asm/arch/gpio.h>
+#include <asm/omap_common.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
-u32 *const omap_si_rev = (u32 *)OMAP4_SRAM_SCRATCH_OMAP4_REV;
+u32 *const omap_si_rev = (u32 *)OMAP_SRAM_SCRATCH_OMAP_REV;
 
 static const struct gpio_bank gpio_bank_44xx[6] = {
 	{ (void *)OMAP44XX_GPIO1_BASE, METHOD_GPIO_24XX },
diff --git a/arch/arm/cpu/armv7/omap5/emif.c b/arch/arm/cpu/armv7/omap5/emif.c
index 3f37abdf83..b4c1319adc 100644
--- a/arch/arm/cpu/armv7/omap5/emif.c
+++ b/arch/arm/cpu/armv7/omap5/emif.c
@@ -32,8 +32,8 @@
 
 #ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
 #define print_timing_reg(reg) debug(#reg" - 0x%08x\n", (reg))
-static u32 *const T_num = (u32 *)OMAP5_SRAM_SCRATCH_EMIF_T_NUM;
-static u32 *const T_den = (u32 *)OMAP5_SRAM_SCRATCH_EMIF_T_DEN;
+static u32 *const T_num = (u32 *)OMAP_SRAM_SCRATCH_EMIF_T_NUM;
+static u32 *const T_den = (u32 *)OMAP_SRAM_SCRATCH_EMIF_T_DEN;
 #endif
 
 #ifdef CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
diff --git a/arch/arm/cpu/armv7/omap5/hw_data.c b/arch/arm/cpu/armv7/omap5/hw_data.c
index ced274e4db..604fa42b1b 100644
--- a/arch/arm/cpu/armv7/omap5/hw_data.c
+++ b/arch/arm/cpu/armv7/omap5/hw_data.c
@@ -41,7 +41,7 @@ struct dplls const **dplls_data =
 struct vcores_data const **omap_vcores =
 		(struct vcores_data const **) OMAP_SRAM_SCRATCH_VCORES_PTR;
 struct omap_sys_ctrl_regs const **ctrl =
-	(struct omap_sys_ctrl_regs const **)OMAP5_SRAM_SCRATCH_SYS_CTRL;
+	(struct omap_sys_ctrl_regs const **)OMAP_SRAM_SCRATCH_SYS_CTRL;
 
 /* OPP HIGH FREQUENCY for ES2.0 */
 static const struct dpll_params mpu_dpll_params_1_5ghz[NUM_SYS_CLKS] = {
@@ -403,6 +403,7 @@ void enable_basic_uboot_clocks(void)
 	};
 
 	u32 const clk_modules_hw_auto_essential[] = {
+		(*prcm)->cm_l3init_hsusbtll_clkctrl,
 		0
 	};
 
@@ -411,7 +412,7 @@ void enable_basic_uboot_clocks(void)
 		(*prcm)->cm_l4per_i2c2_clkctrl,
 		(*prcm)->cm_l4per_i2c3_clkctrl,
 		(*prcm)->cm_l4per_i2c4_clkctrl,
-		(*prcm)->cm_l3init_hsusbtll_clkctrl,
+		(*prcm)->cm_l4per_i2c5_clkctrl,
 		(*prcm)->cm_l3init_hsusbhost_clkctrl,
 		(*prcm)->cm_l3init_fsusb_clkctrl,
 		0
diff --git a/arch/arm/cpu/armv7/omap5/hwinit.c b/arch/arm/cpu/armv7/omap5/hwinit.c
index 2f4b24752b..e192fea0eb 100644
--- a/arch/arm/cpu/armv7/omap5/hwinit.c
+++ b/arch/arm/cpu/armv7/omap5/hwinit.c
@@ -37,10 +37,11 @@
 #include <asm/utils.h>
 #include <asm/arch/gpio.h>
 #include <asm/emif.h>
+#include <asm/omap_common.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
-u32 *const omap_si_rev = (u32 *)OMAP5_SRAM_SCRATCH_OMAP5_REV;
+u32 *const omap_si_rev = (u32 *)OMAP_SRAM_SCRATCH_OMAP_REV;
 
 static struct gpio_bank gpio_bank_54xx[6] = {
 	{ (void *)OMAP54XX_GPIO1_BASE, METHOD_GPIO_24XX },
@@ -363,3 +364,22 @@ u32 warm_reset(void)
 {
 	return readl((*prcm)->prm_rstst) & PRM_RSTST_WARM_RESET_MASK;
 }
+
+void setup_warmreset_time(void)
+{
+	u32 rst_time, rst_val;
+
+#ifndef CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC
+	rst_time = CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC;
+#else
+	rst_time = CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC;
+#endif
+	rst_time = usec_to_32k(rst_time) << RSTTIME1_SHIFT;
+
+	if (rst_time > RSTTIME1_MASK)
+		rst_time = RSTTIME1_MASK;
+
+	rst_val = readl((*prcm)->prm_rsttime) & ~RSTTIME1_MASK;
+	rst_val |= rst_time;
+	writel(rst_val, (*prcm)->prm_rsttime);
+}
diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c
index b8a61fe881..e9f6a32653 100644
--- a/arch/arm/cpu/armv7/omap5/prcm-regs.c
+++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c
@@ -729,6 +729,7 @@ struct prcm_regs const omap5_es2_prcm = {
 	.cm_wkupaon_io_srcomp_clkctrl = 0x4ae07998,
 	.prm_rstctrl = 0x4ae07c00,
 	.prm_rstst = 0x4ae07c04,
+	.prm_rsttime = 0x4ae07c08,
 	.prm_vc_val_bypass = 0x4ae07ca0,
 	.prm_vc_cfg_i2c_mode = 0x4ae07cb4,
 	.prm_vc_cfg_i2c_clk = 0x4ae07cb8,
@@ -952,6 +953,7 @@ struct prcm_regs const dra7xx_prcm = {
 	.cm_wkupaon_scrm_clkctrl		= 0x4ae07890,
 	.prm_rstctrl				= 0x4ae07d00,
 	.prm_rstst				= 0x4ae07d04,
+	.prm_rsttime				= 0x4ae07d08,
 	.prm_vc_val_bypass			= 0x4ae07da0,
 	.prm_vc_cfg_i2c_mode			= 0x4ae07db4,
 	.prm_vc_cfg_i2c_clk			= 0x4ae07db8,
diff --git a/arch/arm/include/asm/arch-am33xx/ddr_defs.h b/arch/arm/include/asm/arch-am33xx/ddr_defs.h
index fb4e78edfe..bb53a6a14e 100644
--- a/arch/arm/include/asm/arch-am33xx/ddr_defs.h
+++ b/arch/arm/include/asm/arch-am33xx/ddr_defs.h
@@ -117,6 +117,23 @@
 #define MT41J512M8RH125_PHY_WR_DATA		0x74
 #define MT41J512M8RH125_IOCTRL_VALUE		0x18B
 
+/* Samsung K4B2G1646E-BIH9 */
+#define K4B2G1646EBIH9_EMIF_READ_LATENCY	0x06
+#define K4B2G1646EBIH9_EMIF_TIM1		0x0888A39B
+#define K4B2G1646EBIH9_EMIF_TIM2		0x2A04011A
+#define K4B2G1646EBIH9_EMIF_TIM3		0x501F820F
+#define K4B2G1646EBIH9_EMIF_SDCFG		0x61C24AB2
+#define K4B2G1646EBIH9_EMIF_SDREF		0x0000093B
+#define K4B2G1646EBIH9_ZQ_CFG			0x50074BE4
+#define K4B2G1646EBIH9_DLL_LOCK_DIFF		0x1
+#define K4B2G1646EBIH9_RATIO			0x40
+#define K4B2G1646EBIH9_INVERT_CLKOUT		0x1
+#define K4B2G1646EBIH9_RD_DQS			0x3B
+#define K4B2G1646EBIH9_WR_DQS			0x85
+#define K4B2G1646EBIH9_PHY_FIFO_WE		0x100
+#define K4B2G1646EBIH9_PHY_WR_DATA		0xC1
+#define K4B2G1646EBIH9_IOCTRL_VALUE		0x18B
+
 /**
  * Configure DMM
  */
diff --git a/arch/arm/include/asm/arch-am33xx/hardware_ti814x.h b/arch/arm/include/asm/arch-am33xx/hardware_ti814x.h
index a950ac3c18..8f9315c020 100644
--- a/arch/arm/include/asm/arch-am33xx/hardware_ti814x.h
+++ b/arch/arm/include/asm/arch-am33xx/hardware_ti814x.h
@@ -29,6 +29,7 @@
 
 /* Control Module Base Address */
 #define CTRL_BASE			0x48140000
+#define CTRL_DEVICE_BASE		0x48140600
 
 /* PRCM Base Address */
 #define PRCM_BASE			0x48180000
diff --git a/arch/arm/include/asm/arch-am33xx/omap.h b/arch/arm/include/asm/arch-am33xx/omap.h
index d28f9a83ff..7e3bb9c994 100644
--- a/arch/arm/include/asm/arch-am33xx/omap.h
+++ b/arch/arm/include/asm/arch-am33xx/omap.h
@@ -35,29 +35,4 @@
 #define NON_SECURE_SRAM_START	0x40300000
 #define NON_SECURE_SRAM_END	0x40320000
 #endif
-
-/* ROM code defines */
-/* Boot device */
-#define BOOT_DEVICE_MASK	0xFF
-#define BOOT_DEVICE_OFFSET	0x8
-#define DEV_DESC_PTR_OFFSET	0x4
-#define DEV_DATA_PTR_OFFSET	0x18
-#define BOOT_MODE_OFFSET	0x8
-#define RESET_REASON_OFFSET	0x9
-#define CH_FLAGS_OFFSET		0xA
-
-#define CH_FLAGS_CHSETTINGS	(0x1 << 0)
-#define CH_FLAGS_CHRAM		(0x1 << 1)
-#define CH_FLAGS_CHFLASH	(0x1 << 2)
-#define CH_FLAGS_CHMMCSD	(0x1 << 3)
-
-#ifndef __ASSEMBLY__
-struct omap_boot_parameters {
-	char *boot_message;
-	unsigned int mem_boot_descriptor;
-	unsigned char omap_bootdevice;
-	unsigned char reset_reason;
-	unsigned char ch_flags;
-};
-#endif
 #endif
diff --git a/arch/arm/include/asm/arch-davinci/hardware.h b/arch/arm/include/asm/arch-davinci/hardware.h
index 6eed6c95a7..a9017e4683 100644
--- a/arch/arm/include/asm/arch-davinci/hardware.h
+++ b/arch/arm/include/asm/arch-davinci/hardware.h
@@ -346,6 +346,8 @@ void davinci_errata_workarounds(void);
 #define PSC_PSC0_MODULE_ID_CNT		16
 #define PSC_PSC1_MODULE_ID_CNT		32
 
+#define UART0_PWREMU_MGMT		(0x01c42030)
+
 struct davinci_psc_regs {
 	dv_reg	revid;
 	dv_reg	rsvd0[71];
diff --git a/arch/arm/include/asm/arch-davinci/nand_defs.h b/arch/arm/include/asm/arch-davinci/nand_defs.h
index 10f3a392ab..4a30813808 100644
--- a/arch/arm/include/asm/arch-davinci/nand_defs.h
+++ b/arch/arm/include/asm/arch-davinci/nand_defs.h
@@ -36,6 +36,15 @@
 #define	MASK_ALE	0x08
 #endif
 
+#ifdef CONFIG_SYS_NAND_MASK_CLE
+#undef MASK_CLE
+#define MASK_CLE CONFIG_SYS_NAND_MASK_CLE
+#endif
+#ifdef CONFIG_SYS_NAND_MASK_ALE
+#undef MASK_ALE
+#define MASK_ALE CONFIG_SYS_NAND_MASK_ALE
+#endif
+
 #define NAND_READ_START		0x00
 #define NAND_READ_END		0x30
 #define NAND_STATUS		0x70
diff --git a/arch/arm/include/asm/arch-omap4/omap.h b/arch/arm/include/asm/arch-omap4/omap.h
index ad984da0b4..e9a6ffeb83 100644
--- a/arch/arm/include/asm/arch-omap4/omap.h
+++ b/arch/arm/include/asm/arch-omap4/omap.h
@@ -143,40 +143,4 @@ struct s32ktimer {
 #define NON_SECURE_SRAM_END	0x4030E000	/* Not inclusive */
 /* base address for indirect vectors (internal boot mode) */
 #define SRAM_ROM_VECT_BASE	0x4030D000
-/* Temporary SRAM stack used while low level init is done */
-#define SRAM_SCRATCH_SPACE_ADDR		NON_SECURE_SRAM_START
-/* SRAM scratch space entries */
-#define OMAP4_SRAM_SCRATCH_OMAP4_REV	SRAM_SCRATCH_SPACE_ADDR
-#define OMAP4_SRAM_SCRATCH_EMIF_T_NUM	(SRAM_SCRATCH_SPACE_ADDR + 0xC)
-#define OMAP4_SRAM_SCRATCH_EMIF_T_DEN	(SRAM_SCRATCH_SPACE_ADDR + 0x10)
-#define OMAP_SRAM_SCRATCH_PRCM_PTR      (SRAM_SCRATCH_SPACE_ADDR + 0x14)
-#define OMAP_SRAM_SCRATCH_DPLLS_PTR     (SRAM_SCRATCH_SPACE_ADDR + 0x18)
-#define OMAP_SRAM_SCRATCH_VCORES_PTR	(SRAM_SCRATCH_SPACE_ADDR + 0x1C)
-#define OMAP4_SRAM_SCRATCH_SYS_CTRL	(SRAM_SCRATCH_SPACE_ADDR + 0x20)
-#define OMAP4_SRAM_SCRATCH_SPACE_END	(SRAM_SCRATCH_SPACE_ADDR + 0x24)
-
-/* ROM code defines */
-/* Boot device */
-#define BOOT_DEVICE_MASK	0xFF
-#define BOOT_DEVICE_OFFSET	0x8
-#define DEV_DESC_PTR_OFFSET	0x4
-#define DEV_DATA_PTR_OFFSET	0x18
-#define BOOT_MODE_OFFSET	0x8
-#define RESET_REASON_OFFSET	0x9
-#define CH_FLAGS_OFFSET		0xA
-
-#define CH_FLAGS_CHSETTINGS	(0x1 << 0)
-#define CH_FLAGS_CHRAM		(0x1 << 1)
-#define CH_FLAGS_CHFLASH	(0x1 << 2)
-#define CH_FLAGS_CHMMCSD	(0x1 << 3)
-
-#ifndef __ASSEMBLY__
-struct omap_boot_parameters {
-	char *boot_message;
-	unsigned int mem_boot_descriptor;
-	unsigned char omap_bootdevice;
-	unsigned char reset_reason;
-	unsigned char ch_flags;
-};
-#endif
 #endif
diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h
index d5f1868eee..039a1f2604 100644
--- a/arch/arm/include/asm/arch-omap4/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap4/sys_proto.h
@@ -27,6 +27,8 @@
 #include <asm/omap_common.h>
 #include <asm/arch/mux_omap4.h>
 
+DECLARE_GLOBAL_DATA_PTR;
+
 struct omap_sysinfo {
 	char *board_string;
 };
@@ -58,13 +60,7 @@ void omap_vc_init(u16 speed_khz);
 int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data);
 u32 warm_reset(void);
 void force_emif_self_refresh(void);
-/*
- * This is used to verify if the configuration header
- * was executed by Romcode prior to control of transfer
- * to the bootloader. SPL is responsible for saving and
- * passing this to the u-boot.
- */
-extern struct omap_boot_parameters boot_params;
+void setup_warmreset_time(void);
 
 static inline u32 running_from_sdram(void)
 {
@@ -84,7 +80,7 @@ static inline u8 uboot_loaded_by_spl(void)
 	 * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a
 	 * mandatory section if CH is present.
 	 */
-	if ((boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
+	if ((gd->arch.omap_boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
 		return 0;
 	else
 		return running_from_sdram();
diff --git a/arch/arm/include/asm/arch-omap5/clocks.h b/arch/arm/include/asm/arch-omap5/clocks.h
index cfde374333..68afa76696 100644
--- a/arch/arm/include/asm/arch-omap5/clocks.h
+++ b/arch/arm/include/asm/arch-omap5/clocks.h
@@ -190,6 +190,10 @@
 #define OPTFCLKEN_SRCOMP_FCLK_SHIFT		8
 #define OPTFCLKEN_SRCOMP_FCLK_MASK		(1 << 8)
 
+/* PRM_RSTTIME */
+#define RSTTIME1_SHIFT				0
+#define RSTTIME1_MASK				(0x3ff << 0)
+
 /* Clock frequencies */
 #define OMAP_SYS_CLK_FREQ_38_4_MHZ	38400000
 #define OMAP_SYS_CLK_IND_38_4_MHZ	6
@@ -251,4 +255,10 @@
 #define DPLL_NO_LOCK	0
 #define DPLL_LOCK	1
 
+/*
+ * MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff.
+ * 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles
+ * into microsec and passing the value.
+ */
+#define CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC	31219
 #endif /* _CLOCKS_OMAP5_H_ */
diff --git a/arch/arm/include/asm/arch-omap5/cpu.h b/arch/arm/include/asm/arch-omap5/cpu.h
index 5e62013236..044ab5581a 100644
--- a/arch/arm/include/asm/arch-omap5/cpu.h
+++ b/arch/arm/include/asm/arch-omap5/cpu.h
@@ -142,6 +142,8 @@ struct watchdog {
 #define I2C_BASE1		(OMAP54XX_L4_PER_BASE + 0x70000)
 #define I2C_BASE2		(OMAP54XX_L4_PER_BASE + 0x72000)
 #define I2C_BASE3		(OMAP54XX_L4_PER_BASE + 0x60000)
+#define I2C_BASE4		(OMAP54XX_L4_PER_BASE + 0x7A000)
+#define I2C_BASE5		(OMAP54XX_L4_PER_BASE + 0x7C000)
 
 /* MUSB base */
 #define MUSB_BASE		(OMAP54XX_L4_CORE_BASE + 0xAB000)
diff --git a/arch/arm/include/asm/arch-omap5/i2c.h b/arch/arm/include/asm/arch-omap5/i2c.h
index 68be03be58..ec39a5318d 100644
--- a/arch/arm/include/asm/arch-omap5/i2c.h
+++ b/arch/arm/include/asm/arch-omap5/i2c.h
@@ -23,7 +23,7 @@
 #ifndef _OMAP5_I2C_H_
 #define _OMAP5_I2C_H_
 
-#define I2C_BUS_MAX	3
+#define I2C_BUS_MAX	5
 #define I2C_DEFAULT_BASE	I2C_BASE1
 
 struct i2c {
diff --git a/arch/arm/include/asm/arch-omap5/omap.h b/arch/arm/include/asm/arch-omap5/omap.h
index 887fcaa5ff..4f43a903d8 100644
--- a/arch/arm/include/asm/arch-omap5/omap.h
+++ b/arch/arm/include/asm/arch-omap5/omap.h
@@ -191,19 +191,6 @@ struct s32ktimer {
 /* base address for indirect vectors (internal boot mode) */
 #define SRAM_ROM_VECT_BASE	0x4031F000
 
-#define SRAM_SCRATCH_SPACE_ADDR		NON_SECURE_SRAM_START
-/*
- * SRAM scratch space entries
- */
-#define OMAP5_SRAM_SCRATCH_OMAP5_REV	SRAM_SCRATCH_SPACE_ADDR
-#define OMAP5_SRAM_SCRATCH_EMIF_T_NUM	(SRAM_SCRATCH_SPACE_ADDR + 0xC)
-#define OMAP5_SRAM_SCRATCH_EMIF_T_DEN	(SRAM_SCRATCH_SPACE_ADDR + 0x10)
-#define OMAP_SRAM_SCRATCH_PRCM_PTR      (SRAM_SCRATCH_SPACE_ADDR + 0x14)
-#define OMAP_SRAM_SCRATCH_DPLLS_PTR     (SRAM_SCRATCH_SPACE_ADDR + 0x18)
-#define OMAP_SRAM_SCRATCH_VCORES_PTR    (SRAM_SCRATCH_SPACE_ADDR + 0x1C)
-#define OMAP5_SRAM_SCRATCH_SYS_CTRL	(SRAM_SCRATCH_SPACE_ADDR + 0x20)
-#define OMAP5_SRAM_SCRATCH_SPACE_END	(SRAM_SCRATCH_SPACE_ADDR + 0x24)
-
 /* Silicon revisions */
 #define OMAP4430_SILICON_ID_INVALID	0xFFFFFFFF
 #define OMAP4430_ES1_0	0x44300100
@@ -214,21 +201,6 @@ struct s32ktimer {
 #define OMAP4460_ES1_0	0x44600100
 #define OMAP4460_ES1_1	0x44600110
 
-/* ROM code defines */
-/* Boot device */
-#define BOOT_DEVICE_MASK	0xFF
-#define BOOT_DEVICE_OFFSET	0x8
-#define DEV_DESC_PTR_OFFSET	0x4
-#define DEV_DATA_PTR_OFFSET	0x18
-#define BOOT_MODE_OFFSET	0x8
-#define RESET_REASON_OFFSET     0x9
-#define CH_FLAGS_OFFSET         0xA
-
-#define CH_FLAGS_CHSETTINGS	(0x1 << 0)
-#define	CH_FLAGS_CHRAM		(0x1 << 1)
-#define CH_FLAGS_CHFLASH	(0x1 << 2)
-#define CH_FLAGS_CHMMCSD	(0x1 << 3)
-
 /* CONTROL_SRCOMP_XXX_SIDE */
 #define OVERRIDE_XS_SHIFT		30
 #define OVERRIDE_XS_MASK		(1 << 30)
@@ -249,14 +221,6 @@ struct srcomp_params {
 	s8 multiply_factor;
 };
 
-struct omap_boot_parameters {
-	char *boot_message;
-	unsigned int mem_boot_descriptor;
-	unsigned char omap_bootdevice;
-	unsigned char reset_reason;
-	unsigned char ch_flags;
-};
-
 struct ctrl_ioregs {
 	u32 ctrl_ddrch;
 	u32 ctrl_lpddr2ch;
diff --git a/arch/arm/include/asm/arch-omap5/sys_proto.h b/arch/arm/include/asm/arch-omap5/sys_proto.h
index e66ab44341..b79161d79a 100644
--- a/arch/arm/include/asm/arch-omap5/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap5/sys_proto.h
@@ -27,6 +27,8 @@
 #include <asm/omap_common.h>
 #include <asm/arch/clocks.h>
 
+DECLARE_GLOBAL_DATA_PTR;
+
 struct pad_conf_entry {
 	u32 offset;
 	u32 val;
@@ -64,14 +66,7 @@ u32 warm_reset(void);
 void force_emif_self_refresh(void);
 void get_ioregs(const struct ctrl_ioregs **regs);
 void srcomp_enable(void);
-
-/*
- * This is used to verify if the configuration header
- * was executed by Romcode prior to control of transfer
- * to the bootloader. SPL is responsible for saving and
- * passing this to the u-boot.
- */
-extern struct omap_boot_parameters boot_params;
+void setup_warmreset_time(void);
 
 static inline u32 running_from_sdram(void)
 {
@@ -91,7 +86,7 @@ static inline u8 uboot_loaded_by_spl(void)
 	 * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a
 	 * mandatory section if CH is present.
 	 */
-	if ((boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
+	if ((gd->arch.omap_boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
 		return 0;
 	else
 		return running_from_sdram();
@@ -122,4 +117,13 @@ static inline u32 omap_hw_init_context(void)
 #endif
 }
 
+static inline u32 div_round_up(u32 num, u32 den)
+{
+	return (num + den - 1)/den;
+}
+
+static inline u32 usec_to_32k(u32 usec)
+{
+	return div_round_up(32768 * usec, 1000000);
+}
 #endif
diff --git a/arch/arm/include/asm/global_data.h b/arch/arm/include/asm/global_data.h
index 37ac0daa70..7611d0a18b 100644
--- a/arch/arm/include/asm/global_data.h
+++ b/arch/arm/include/asm/global_data.h
@@ -24,6 +24,10 @@
 #ifndef	__ASM_GBL_DATA_H
 #define __ASM_GBL_DATA_H
 
+#ifdef CONFIG_OMAP
+#include <asm/omap_boot.h>
+#endif
+
 /* Architecture-specific global data */
 struct arch_global_data {
 #if defined(CONFIG_FSL_ESDHC)
@@ -51,6 +55,10 @@ struct arch_global_data {
 	unsigned long tlb_addr;
 	unsigned long tlb_size;
 #endif
+
+#ifdef CONFIG_OMAP
+	struct omap_boot_parameters omap_boot_params;
+#endif
 };
 
 #include <asm-generic/global_data.h>
diff --git a/arch/arm/include/asm/omap_boot.h b/arch/arm/include/asm/omap_boot.h
new file mode 100644
index 0000000000..a803965ac5
--- /dev/null
+++ b/arch/arm/include/asm/omap_boot.h
@@ -0,0 +1,50 @@
+/*
+ * (C) Copyright 2013
+ * Texas Instruments, <www.ti.com>
+ *
+ * Sricharan R <r.sricharan@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* ROM code defines */
+/* Boot device */
+#define BOOT_DEVICE_MASK	0xFF
+#define BOOT_DEVICE_OFFSET	0x8
+#define DEV_DESC_PTR_OFFSET	0x4
+#define DEV_DATA_PTR_OFFSET	0x18
+#define BOOT_MODE_OFFSET	0x8
+#define RESET_REASON_OFFSET	0x9
+#define CH_FLAGS_OFFSET		0xA
+
+#define CH_FLAGS_CHSETTINGS	(0x1 << 0)
+#define CH_FLAGS_CHRAM		(0x1 << 1)
+#define CH_FLAGS_CHFLASH	(0x1 << 2)
+#define CH_FLAGS_CHMMCSD	(0x1 << 3)
+
+#ifndef __ASSEMBLY__
+struct omap_boot_parameters {
+	char *boot_message;
+	unsigned int mem_boot_descriptor;
+	unsigned char omap_bootdevice;
+	unsigned char reset_reason;
+	unsigned char ch_flags;
+	unsigned long omap_bootmode;
+};
+#endif
diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h
index 091ddb508d..ee7b188d3a 100644
--- a/arch/arm/include/asm/omap_common.h
+++ b/arch/arm/include/asm/omap_common.h
@@ -25,6 +25,8 @@
 #ifndef	_OMAP_COMMON_H_
 #define	_OMAP_COMMON_H_
 
+#ifndef __ASSEMBLY__
+
 #include <common.h>
 
 #define NUM_SYS_CLKS	8
@@ -316,6 +318,7 @@ struct prcm_regs {
 	u32 cm_wkupaon_io_srcomp_clkctrl;
 	u32 prm_rstctrl;
 	u32 prm_rstst;
+	u32 prm_rsttime;
 	u32 prm_vc_val_bypass;
 	u32 prm_vc_cfg_i2c_mode;
 	u32 prm_vc_cfg_i2c_clk;
@@ -557,6 +560,7 @@ static inline u32 omap_revision(void)
 	extern u32 *const omap_si_rev;
 	return *omap_si_rev;
 }
+#endif
 
 /*
  * silicon revisions.
@@ -583,4 +587,20 @@ static inline u32 omap_revision(void)
 
 /* DRA7XX */
 #define DRA752_ES1_0	0x07520100
+
+/*
+ * SRAM scratch space entries
+ */
+#define SRAM_SCRATCH_SPACE_ADDR		NON_SECURE_SRAM_START
+#define OMAP_SRAM_SCRATCH_OMAP_REV	SRAM_SCRATCH_SPACE_ADDR
+#define OMAP_SRAM_SCRATCH_EMIF_SIZE	(SRAM_SCRATCH_SPACE_ADDR + 0x4)
+#define OMAP_SRAM_SCRATCH_EMIF_T_NUM	(SRAM_SCRATCH_SPACE_ADDR + 0xC)
+#define OMAP_SRAM_SCRATCH_EMIF_T_DEN	(SRAM_SCRATCH_SPACE_ADDR + 0x10)
+#define OMAP_SRAM_SCRATCH_PRCM_PTR      (SRAM_SCRATCH_SPACE_ADDR + 0x14)
+#define OMAP_SRAM_SCRATCH_DPLLS_PTR     (SRAM_SCRATCH_SPACE_ADDR + 0x18)
+#define OMAP_SRAM_SCRATCH_VCORES_PTR    (SRAM_SCRATCH_SPACE_ADDR + 0x1C)
+#define OMAP_SRAM_SCRATCH_SYS_CTRL	(SRAM_SCRATCH_SPACE_ADDR + 0x20)
+#define OMAP_SRAM_SCRATCH_BOOT_PARAMS	(SRAM_SCRATCH_SPACE_ADDR + 0x24)
+#define OMAP5_SRAM_SCRATCH_SPACE_END	(SRAM_SCRATCH_SPACE_ADDR + 0x28)
+
 #endif /* _OMAP_COMMON_H_ */
diff --git a/board/cm_t35/Makefile b/board/cm_t35/Makefile
deleted file mode 100644
index bde56e61f4..0000000000
--- a/board/cm_t35/Makefile
+++ /dev/null
@@ -1,44 +0,0 @@
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(BOARD).o
-
-COBJS-$(CONFIG_DRIVER_OMAP34XX_I2C) += eeprom.o
-COBJS-$(CONFIG_LCD) += display.o
-
-COBJS	:= cm_t35.o leds.o $(COBJS-y)
-
-SRCS	:= $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-
-$(LIB):	$(obj).depend $(OBJS)
-	$(call cmd_link_o_target, $(OBJS))
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
diff --git a/board/cm_t35/cm_t35.c b/board/cm_t35/cm_t35.c
deleted file mode 100644
index 84c36bafb4..0000000000
--- a/board/cm_t35/cm_t35.c
+++ /dev/null
@@ -1,617 +0,0 @@
-/*
- * (C) Copyright 2011 CompuLab, Ltd. <www.compulab.co.il>
- *
- * Authors: Mike Rapoport <mike@compulab.co.il>
- *	    Igor Grinberg <grinberg@compulab.co.il>
- *
- * Derived from omap3evm and Beagle Board by
- *	Manikandan Pillai <mani.pillai@ti.com>
- *	Richard Woodruff <r-woodruff2@ti.com>
- *	Syed Mohammed Khasim <x0khasim@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc.
- */
-
-#include <common.h>
-#include <status_led.h>
-#include <netdev.h>
-#include <net.h>
-#include <i2c.h>
-#include <usb.h>
-#include <mmc.h>
-#include <nand.h>
-#include <twl4030.h>
-#include <bmp_layout.h>
-#include <linux/compiler.h>
-
-#include <asm/io.h>
-#include <asm/arch/mem.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/mmc_host_def.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/mach-types.h>
-#include <asm/ehci-omap.h>
-#include <asm/gpio.h>
-
-#include "eeprom.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-const omap3_sysinfo sysinfo = {
-	DDR_DISCRETE,
-	"CM-T3x board",
-	"NAND",
-};
-
-static u32 gpmc_net_config[GPMC_MAX_REG] = {
-	NET_GPMC_CONFIG1,
-	NET_GPMC_CONFIG2,
-	NET_GPMC_CONFIG3,
-	NET_GPMC_CONFIG4,
-	NET_GPMC_CONFIG5,
-	NET_GPMC_CONFIG6,
-	0
-};
-
-static u32 gpmc_nand_config[GPMC_MAX_REG] = {
-	SMNAND_GPMC_CONFIG1,
-	SMNAND_GPMC_CONFIG2,
-	SMNAND_GPMC_CONFIG3,
-	SMNAND_GPMC_CONFIG4,
-	SMNAND_GPMC_CONFIG5,
-	SMNAND_GPMC_CONFIG6,
-	0,
-};
-
-#ifdef CONFIG_LCD
-#ifdef CONFIG_CMD_NAND
-static int splash_load_from_nand(u32 bmp_load_addr)
-{
-	struct bmp_header *bmp_hdr;
-	int res, splash_screen_nand_offset = 0x100000;
-	size_t bmp_size, bmp_header_size = sizeof(struct bmp_header);
-
-	if (bmp_load_addr + bmp_header_size >= gd->start_addr_sp)
-		goto splash_address_too_high;
-
-	res = nand_read_skip_bad(&nand_info[nand_curr_device],
-			splash_screen_nand_offset, &bmp_header_size,
-			NULL, nand_info[nand_curr_device].size,
-			(u_char *)bmp_load_addr);
-	if (res < 0)
-		return res;
-
-	bmp_hdr = (struct bmp_header *)bmp_load_addr;
-	bmp_size = le32_to_cpu(bmp_hdr->file_size);
-
-	if (bmp_load_addr + bmp_size >= gd->start_addr_sp)
-		goto splash_address_too_high;
-
-	return nand_read_skip_bad(&nand_info[nand_curr_device],
-			splash_screen_nand_offset, &bmp_size,
-			NULL, nand_info[nand_curr_device].size,
-			(u_char *)bmp_load_addr);
-
-splash_address_too_high:
-	printf("Error: splashimage address too high. Data overwrites U-Boot "
-		"and/or placed beyond DRAM boundaries.\n");
-
-	return -1;
-}
-#else
-static inline int splash_load_from_nand(void)
-{
-	return -1;
-}
-#endif /* CONFIG_CMD_NAND */
-
-int board_splash_screen_prepare(void)
-{
-	char *env_splashimage_value;
-	u32 bmp_load_addr;
-
-	env_splashimage_value = getenv("splashimage");
-	if (env_splashimage_value == NULL)
-		return -1;
-
-	bmp_load_addr = simple_strtoul(env_splashimage_value, 0, 16);
-	if (bmp_load_addr == 0) {
-		printf("Error: bad splashimage address specified\n");
-		return -1;
-	}
-
-	return splash_load_from_nand(bmp_load_addr);
-}
-#endif /* CONFIG_LCD */
-
-/*
- * Routine: board_init
- * Description: hardware init.
- */
-int board_init(void)
-{
-	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
-
-	enable_gpmc_cs_config(gpmc_nand_config, &gpmc_cfg->cs[0],
-			      CONFIG_SYS_NAND_BASE, GPMC_SIZE_16M);
-
-	/* board id for Linux */
-	if (get_cpu_family() == CPU_OMAP34XX)
-		gd->bd->bi_arch_number = MACH_TYPE_CM_T35;
-	else
-		gd->bd->bi_arch_number = MACH_TYPE_CM_T3730;
-
-	/* boot param addr */
-	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
-	status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
-#endif
-
-	return 0;
-}
-
-static u32 cm_t3x_rev;
-
-/*
- * Routine: get_board_rev
- * Description: read system revision
- */
-u32 get_board_rev(void)
-{
-	if (!cm_t3x_rev)
-		cm_t3x_rev = cm_t3x_eeprom_get_board_rev();
-
-	return cm_t3x_rev;
-};
-
-/*
- * Routine: misc_init_r
- * Description: display die ID
- */
-int misc_init_r(void)
-{
-	u32 board_rev = get_board_rev();
-	u32 rev_major = board_rev / 100;
-	u32 rev_minor = board_rev - (rev_major * 100);
-
-	if ((rev_minor / 10) * 10 == rev_minor)
-		rev_minor = rev_minor / 10;
-
-	printf("PCB:   %u.%u\n", rev_major, rev_minor);
-	dieid_num_r();
-
-	return 0;
-}
-
-/*
- * Routine: set_muxconf_regs
- * Description: Setting up the configuration Mux registers specific to the
- *		hardware. Many pins need to be moved from protect to primary
- *		mode.
- */
-static void cm_t3x_set_common_muxconf(void)
-{
-	/* SDRC */
-	MUX_VAL(CP(SDRC_D0),		(IEN  | PTD | DIS | M0)); /*SDRC_D0*/
-	MUX_VAL(CP(SDRC_D1),		(IEN  | PTD | DIS | M0)); /*SDRC_D1*/
-	MUX_VAL(CP(SDRC_D2),		(IEN  | PTD | DIS | M0)); /*SDRC_D2*/
-	MUX_VAL(CP(SDRC_D3),		(IEN  | PTD | DIS | M0)); /*SDRC_D3*/
-	MUX_VAL(CP(SDRC_D4),		(IEN  | PTD | DIS | M0)); /*SDRC_D4*/
-	MUX_VAL(CP(SDRC_D5),		(IEN  | PTD | DIS | M0)); /*SDRC_D5*/
-	MUX_VAL(CP(SDRC_D6),		(IEN  | PTD | DIS | M0)); /*SDRC_D6*/
-	MUX_VAL(CP(SDRC_D7),		(IEN  | PTD | DIS | M0)); /*SDRC_D7*/
-	MUX_VAL(CP(SDRC_D8),		(IEN  | PTD | DIS | M0)); /*SDRC_D8*/
-	MUX_VAL(CP(SDRC_D9),		(IEN  | PTD | DIS | M0)); /*SDRC_D9*/
-	MUX_VAL(CP(SDRC_D10),		(IEN  | PTD | DIS | M0)); /*SDRC_D10*/
-	MUX_VAL(CP(SDRC_D11),		(IEN  | PTD | DIS | M0)); /*SDRC_D11*/
-	MUX_VAL(CP(SDRC_D12),		(IEN  | PTD | DIS | M0)); /*SDRC_D12*/
-	MUX_VAL(CP(SDRC_D13),		(IEN  | PTD | DIS | M0)); /*SDRC_D13*/
-	MUX_VAL(CP(SDRC_D14),		(IEN  | PTD | DIS | M0)); /*SDRC_D14*/
-	MUX_VAL(CP(SDRC_D15),		(IEN  | PTD | DIS | M0)); /*SDRC_D15*/
-	MUX_VAL(CP(SDRC_D16),		(IEN  | PTD | DIS | M0)); /*SDRC_D16*/
-	MUX_VAL(CP(SDRC_D17),		(IEN  | PTD | DIS | M0)); /*SDRC_D17*/
-	MUX_VAL(CP(SDRC_D18),		(IEN  | PTD | DIS | M0)); /*SDRC_D18*/
-	MUX_VAL(CP(SDRC_D19),		(IEN  | PTD | DIS | M0)); /*SDRC_D19*/
-	MUX_VAL(CP(SDRC_D20),		(IEN  | PTD | DIS | M0)); /*SDRC_D20*/
-	MUX_VAL(CP(SDRC_D21),		(IEN  | PTD | DIS | M0)); /*SDRC_D21*/
-	MUX_VAL(CP(SDRC_D22),		(IEN  | PTD | DIS | M0)); /*SDRC_D22*/
-	MUX_VAL(CP(SDRC_D23),		(IEN  | PTD | DIS | M0)); /*SDRC_D23*/
-	MUX_VAL(CP(SDRC_D24),		(IEN  | PTD | DIS | M0)); /*SDRC_D24*/
-	MUX_VAL(CP(SDRC_D25),		(IEN  | PTD | DIS | M0)); /*SDRC_D25*/
-	MUX_VAL(CP(SDRC_D26),		(IEN  | PTD | DIS | M0)); /*SDRC_D26*/
-	MUX_VAL(CP(SDRC_D27),		(IEN  | PTD | DIS | M0)); /*SDRC_D27*/
-	MUX_VAL(CP(SDRC_D28),		(IEN  | PTD | DIS | M0)); /*SDRC_D28*/
-	MUX_VAL(CP(SDRC_D29),		(IEN  | PTD | DIS | M0)); /*SDRC_D29*/
-	MUX_VAL(CP(SDRC_D30),		(IEN  | PTD | DIS | M0)); /*SDRC_D30*/
-	MUX_VAL(CP(SDRC_D31),		(IEN  | PTD | DIS | M0)); /*SDRC_D31*/
-	MUX_VAL(CP(SDRC_CLK),		(IEN  | PTD | DIS | M0)); /*SDRC_CLK*/
-	MUX_VAL(CP(SDRC_DQS0),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS0*/
-	MUX_VAL(CP(SDRC_DQS1),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS1*/
-	MUX_VAL(CP(SDRC_DQS2),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS2*/
-	MUX_VAL(CP(SDRC_DQS3),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS3*/
-	MUX_VAL(CP(SDRC_CKE0),		(IDIS | PTU | EN  | M0)); /*SDRC_CKE0*/
-	MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTD | DIS | M7)); /*SDRC_CKE1*/
-
-	/* GPMC */
-	MUX_VAL(CP(GPMC_A1),		(IDIS | PTU | EN  | M0)); /*GPMC_A1*/
-	MUX_VAL(CP(GPMC_A2),		(IDIS | PTU | EN  | M0)); /*GPMC_A2*/
-	MUX_VAL(CP(GPMC_A3),		(IDIS | PTU | EN  | M0)); /*GPMC_A3*/
-	MUX_VAL(CP(GPMC_A4),		(IDIS | PTU | EN  | M0)); /*GPMC_A4*/
-	MUX_VAL(CP(GPMC_A5),		(IDIS | PTU | EN  | M0)); /*GPMC_A5*/
-	MUX_VAL(CP(GPMC_A6),		(IDIS | PTU | EN  | M0)); /*GPMC_A6*/
-	MUX_VAL(CP(GPMC_A7),		(IDIS | PTU | EN  | M0)); /*GPMC_A7*/
-	MUX_VAL(CP(GPMC_A8),		(IDIS | PTU | EN  | M0)); /*GPMC_A8*/
-	MUX_VAL(CP(GPMC_A9),		(IDIS | PTU | EN  | M0)); /*GPMC_A9*/
-	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | EN  | M0)); /*GPMC_A10*/
-	MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0)); /*GPMC_D0*/
-	MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0)); /*GPMC_D1*/
-	MUX_VAL(CP(GPMC_D2),		(IEN  | PTU | EN  | M0)); /*GPMC_D2*/
-	MUX_VAL(CP(GPMC_D3),		(IEN  | PTU | EN  | M0)); /*GPMC_D3*/
-	MUX_VAL(CP(GPMC_D4),		(IEN  | PTU | EN  | M0)); /*GPMC_D4*/
-	MUX_VAL(CP(GPMC_D5),		(IEN  | PTU | EN  | M0)); /*GPMC_D5*/
-	MUX_VAL(CP(GPMC_D6),		(IEN  | PTU | EN  | M0)); /*GPMC_D6*/
-	MUX_VAL(CP(GPMC_D7),		(IEN  | PTU | EN  | M0)); /*GPMC_D7*/
-	MUX_VAL(CP(GPMC_D8),		(IEN  | PTU | EN  | M0)); /*GPMC_D8*/
-	MUX_VAL(CP(GPMC_D9),		(IEN  | PTU | EN  | M0)); /*GPMC_D9*/
-	MUX_VAL(CP(GPMC_D10),		(IEN  | PTU | EN  | M0)); /*GPMC_D10*/
-	MUX_VAL(CP(GPMC_D11),		(IEN  | PTU | EN  | M0)); /*GPMC_D11*/
-	MUX_VAL(CP(GPMC_D12),		(IEN  | PTU | EN  | M0)); /*GPMC_D12*/
-	MUX_VAL(CP(GPMC_D13),		(IEN  | PTU | EN  | M0)); /*GPMC_D13*/
-	MUX_VAL(CP(GPMC_D14),		(IEN  | PTU | EN  | M0)); /*GPMC_D14*/
-	MUX_VAL(CP(GPMC_D15),		(IEN  | PTU | EN  | M0)); /*GPMC_D15*/
-	MUX_VAL(CP(GPMC_NCS0),		(IDIS | PTU | EN  | M0)); /*GPMC_nCS0*/
-
-	/* SB-T35 Ethernet */
-	MUX_VAL(CP(GPMC_NCS4),		(IEN  | PTU | EN  | M0)); /*GPMC_nCS4*/
-
-	/* DVI enable */
-	MUX_VAL(CP(GPMC_NCS3),		(IDIS  | PTU | DIS  | M4));/*GPMC_nCS3*/
-
-	/* CM-T3x Ethernet */
-	MUX_VAL(CP(GPMC_NCS5),		(IDIS | PTU | DIS | M0)); /*GPMC_nCS5*/
-	MUX_VAL(CP(GPMC_CLK),		(IEN  | PTD | DIS | M4)); /*GPIO_59*/
-	MUX_VAL(CP(GPMC_NADV_ALE),	(IDIS | PTD | DIS | M0)); /*nADV_ALE*/
-	MUX_VAL(CP(GPMC_NOE),		(IDIS | PTD | DIS | M0)); /*nOE*/
-	MUX_VAL(CP(GPMC_NWE),		(IDIS | PTD | DIS | M0)); /*nWE*/
-	MUX_VAL(CP(GPMC_NBE0_CLE),	(IDIS | PTU | EN  | M0)); /*nBE0_CLE*/
-	MUX_VAL(CP(GPMC_NBE1),		(IDIS | PTD | DIS | M4)); /*GPIO_61*/
-	MUX_VAL(CP(GPMC_NWP),		(IEN  | PTD | DIS | M0)); /*nWP*/
-	MUX_VAL(CP(GPMC_WAIT0),		(IEN  | PTU | EN  | M0)); /*WAIT0*/
-
-	/* DSS */
-	MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0)); /*DSS_PCLK*/
-	MUX_VAL(CP(DSS_HSYNC),		(IDIS | PTD | DIS | M0)); /*DSS_HSYNC*/
-	MUX_VAL(CP(DSS_VSYNC),		(IDIS | PTD | DIS | M0)); /*DSS_VSYNC*/
-	MUX_VAL(CP(DSS_ACBIAS),		(IDIS | PTD | DIS | M0)); /*DSS_ACBIAS*/
-	MUX_VAL(CP(DSS_DATA6),		(IDIS | PTD | DIS | M0)); /*DSS_DATA6*/
-	MUX_VAL(CP(DSS_DATA7),		(IDIS | PTD | DIS | M0)); /*DSS_DATA7*/
-	MUX_VAL(CP(DSS_DATA8),		(IDIS | PTD | DIS | M0)); /*DSS_DATA8*/
-	MUX_VAL(CP(DSS_DATA9),		(IDIS | PTD | DIS | M0)); /*DSS_DATA9*/
-	MUX_VAL(CP(DSS_DATA10),		(IDIS | PTD | DIS | M0)); /*DSS_DATA10*/
-	MUX_VAL(CP(DSS_DATA11),		(IDIS | PTD | DIS | M0)); /*DSS_DATA11*/
-	MUX_VAL(CP(DSS_DATA12),		(IDIS | PTD | DIS | M0)); /*DSS_DATA12*/
-	MUX_VAL(CP(DSS_DATA13),		(IDIS | PTD | DIS | M0)); /*DSS_DATA13*/
-	MUX_VAL(CP(DSS_DATA14),		(IDIS | PTD | DIS | M0)); /*DSS_DATA14*/
-	MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0)); /*DSS_DATA15*/
-	MUX_VAL(CP(DSS_DATA16),		(IDIS | PTD | DIS | M0)); /*DSS_DATA16*/
-	MUX_VAL(CP(DSS_DATA17),		(IDIS | PTD | DIS | M0)); /*DSS_DATA17*/
-
-	/* serial interface */
-	MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0)); /*UART3_RX*/
-	MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0)); /*UART3_TX*/
-
-	/* mUSB */
-	MUX_VAL(CP(HSUSB0_CLK),		(IEN  | PTD | DIS | M0)); /*HSUSB0_CLK*/
-	MUX_VAL(CP(HSUSB0_STP),		(IDIS | PTU | EN  | M0)); /*HSUSB0_STP*/
-	MUX_VAL(CP(HSUSB0_DIR),		(IEN  | PTD | DIS | M0)); /*HSUSB0_DIR*/
-	MUX_VAL(CP(HSUSB0_NXT),		(IEN  | PTD | DIS | M0)); /*HSUSB0_NXT*/
-	MUX_VAL(CP(HSUSB0_DATA0),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA0*/
-	MUX_VAL(CP(HSUSB0_DATA1),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA1*/
-	MUX_VAL(CP(HSUSB0_DATA2),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA2*/
-	MUX_VAL(CP(HSUSB0_DATA3),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA3*/
-	MUX_VAL(CP(HSUSB0_DATA4),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA4*/
-	MUX_VAL(CP(HSUSB0_DATA5),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA5*/
-	MUX_VAL(CP(HSUSB0_DATA6),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA6*/
-	MUX_VAL(CP(HSUSB0_DATA7),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA7*/
-
-	/* USB EHCI */
-	MUX_VAL(CP(ETK_D0_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT0*/
-	MUX_VAL(CP(ETK_D1_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT1*/
-	MUX_VAL(CP(ETK_D2_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT2*/
-	MUX_VAL(CP(ETK_D7_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT3*/
-	MUX_VAL(CP(ETK_D4_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT4*/
-	MUX_VAL(CP(ETK_D5_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT5*/
-	MUX_VAL(CP(ETK_D6_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT6*/
-	MUX_VAL(CP(ETK_D3_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT7*/
-	MUX_VAL(CP(ETK_D8_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DIR*/
-	MUX_VAL(CP(ETK_D9_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_NXT*/
-	MUX_VAL(CP(ETK_CTL_ES2),	(IDIS | PTD | DIS | M3)); /*HSUSB1_CLK*/
-	MUX_VAL(CP(ETK_CLK_ES2),	(IDIS | PTU | DIS | M3)); /*HSUSB1_STP*/
-
-	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT0*/
-	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT1*/
-	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT2*/
-	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT3*/
-	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT4*/
-	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT5*/
-	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT6*/
-	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT7*/
-	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DIR*/
-	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_NXT*/
-	MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)); /*HSUSB2_CLK*/
-	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | DIS | M3)); /*HSUSB2_STP*/
-
-	/* SB_T35_USB_HUB_RESET_GPIO */
-	MUX_VAL(CP(CAM_WEN),		(IDIS | PTD | DIS | M4)); /*GPIO_167*/
-
-	/* I2C1 */
-	MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0)); /*I2C1_SCL*/
-	MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0)); /*I2C1_SDA*/
-	/* I2C2 */
-	MUX_VAL(CP(I2C2_SCL),		(IEN  | PTU | EN  | M0)); /*I2C2_SCL*/
-	MUX_VAL(CP(I2C2_SDA),		(IEN  | PTU | EN  | M0)); /*I2C2_SDA*/
-	/* I2C3 */
-	MUX_VAL(CP(I2C3_SCL),		(IEN  | PTU | EN  | M0)); /*I2C3_SCL*/
-	MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0)); /*I2C3_SDA*/
-
-	/* control and debug */
-	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | DIS | M0)); /*SYS_32K*/
-	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)); /*SYS_CLKREQ*/
-	MUX_VAL(CP(SYS_NIRQ),		(IEN  | PTU | EN  | M0)); /*SYS_nIRQ*/
-	MUX_VAL(CP(SYS_OFF_MODE),	(IEN  | PTD | DIS | M0)); /*OFF_MODE*/
-	MUX_VAL(CP(SYS_CLKOUT1),	(IEN  | PTD | DIS | M0)); /*CLKOUT1*/
-	MUX_VAL(CP(SYS_CLKOUT2),	(IDIS | PTU | DIS | M4)); /*green LED*/
-	MUX_VAL(CP(JTAG_nTRST),		(IEN  | PTD | DIS | M0)); /*JTAG_nTRST*/
-	MUX_VAL(CP(JTAG_TCK),		(IEN  | PTD | DIS | M0)); /*JTAG_TCK*/
-	MUX_VAL(CP(JTAG_TMS),		(IEN  | PTD | DIS | M0)); /*JTAG_TMS*/
-	MUX_VAL(CP(JTAG_TDI),		(IEN  | PTD | DIS | M0)); /*JTAG_TDI*/
-
-	/* MMC1 */
-	MUX_VAL(CP(MMC1_CLK),		(IDIS | PTU | EN  | M0)); /*MMC1_CLK*/
-	MUX_VAL(CP(MMC1_CMD),		(IEN  | PTU | EN  | M0)); /*MMC1_CMD*/
-	MUX_VAL(CP(MMC1_DAT0),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT0*/
-	MUX_VAL(CP(MMC1_DAT1),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT1*/
-	MUX_VAL(CP(MMC1_DAT2),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT2*/
-	MUX_VAL(CP(MMC1_DAT3),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT3*/
-}
-
-static void cm_t35_set_muxconf(void)
-{
-	/* DSS */
-	MUX_VAL(CP(DSS_DATA0),		(IDIS | PTD | DIS | M0)); /*DSS_DATA0*/
-	MUX_VAL(CP(DSS_DATA1),		(IDIS | PTD | DIS | M0)); /*DSS_DATA1*/
-	MUX_VAL(CP(DSS_DATA2),		(IDIS | PTD | DIS | M0)); /*DSS_DATA2*/
-	MUX_VAL(CP(DSS_DATA3),		(IDIS | PTD | DIS | M0)); /*DSS_DATA3*/
-	MUX_VAL(CP(DSS_DATA4),		(IDIS | PTD | DIS | M0)); /*DSS_DATA4*/
-	MUX_VAL(CP(DSS_DATA5),		(IDIS | PTD | DIS | M0)); /*DSS_DATA5*/
-
-	MUX_VAL(CP(DSS_DATA18),         (IDIS | PTD | DIS | M0)); /*DSS_DATA18*/
-	MUX_VAL(CP(DSS_DATA19),         (IDIS | PTD | DIS | M0)); /*DSS_DATA19*/
-	MUX_VAL(CP(DSS_DATA20),         (IDIS | PTD | DIS | M0)); /*DSS_DATA20*/
-	MUX_VAL(CP(DSS_DATA21),         (IDIS | PTD | DIS | M0)); /*DSS_DATA21*/
-	MUX_VAL(CP(DSS_DATA22),         (IDIS | PTD | DIS | M0)); /*DSS_DATA22*/
-	MUX_VAL(CP(DSS_DATA23),         (IDIS | PTD | DIS | M0)); /*DSS_DATA23*/
-
-	/* MMC1 */
-	MUX_VAL(CP(MMC1_DAT4),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT4*/
-	MUX_VAL(CP(MMC1_DAT5),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT5*/
-	MUX_VAL(CP(MMC1_DAT6),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT6*/
-	MUX_VAL(CP(MMC1_DAT7),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT7*/
-}
-
-static void cm_t3730_set_muxconf(void)
-{
-	/* DSS */
-	MUX_VAL(CP(DSS_DATA18),		(IDIS | PTD | DIS | M3)); /*DSS_DATA0*/
-	MUX_VAL(CP(DSS_DATA19),		(IDIS | PTD | DIS | M3)); /*DSS_DATA1*/
-	MUX_VAL(CP(DSS_DATA20),		(IDIS | PTD | DIS | M3)); /*DSS_DATA2*/
-	MUX_VAL(CP(DSS_DATA21),		(IDIS | PTD | DIS | M3)); /*DSS_DATA3*/
-	MUX_VAL(CP(DSS_DATA22),		(IDIS | PTD | DIS | M3)); /*DSS_DATA4*/
-	MUX_VAL(CP(DSS_DATA23),		(IDIS | PTD | DIS | M3)); /*DSS_DATA5*/
-
-	MUX_VAL(CP(SYS_BOOT0),		(IDIS | PTD | DIS | M3)); /*DSS_DATA18*/
-	MUX_VAL(CP(SYS_BOOT1),		(IDIS | PTD | DIS | M3)); /*DSS_DATA19*/
-	MUX_VAL(CP(SYS_BOOT3),		(IDIS | PTD | DIS | M3)); /*DSS_DATA20*/
-	MUX_VAL(CP(SYS_BOOT4),		(IDIS | PTD | DIS | M3)); /*DSS_DATA21*/
-	MUX_VAL(CP(SYS_BOOT5),		(IDIS | PTD | DIS | M3)); /*DSS_DATA22*/
-	MUX_VAL(CP(SYS_BOOT6),		(IDIS | PTD | DIS | M3)); /*DSS_DATA23*/
-}
-
-void set_muxconf_regs(void)
-{
-	cm_t3x_set_common_muxconf();
-
-	if (get_cpu_family() == CPU_OMAP34XX)
-		cm_t35_set_muxconf();
-	else
-		cm_t3730_set_muxconf();
-}
-
-#ifdef CONFIG_GENERIC_MMC
-int board_mmc_getcd(struct mmc *mmc)
-{
-	u8 val;
-
-	if (twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, &val, TWL4030_BASEADD_GPIO))
-		return -1;
-
-	return !(val & 1);
-}
-
-int board_mmc_init(bd_t *bis)
-{
-	return omap_mmc_init(0, 0, 0, -1, 59);
-}
-#endif
-
-/*
- * Routine: setup_net_chip_gmpc
- * Description: Setting up the configuration GPMC registers specific to the
- *		Ethernet hardware.
- */
-static void setup_net_chip_gmpc(void)
-{
-	struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
-
-	enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[5],
-			      CM_T3X_SMC911X_BASE, GPMC_SIZE_16M);
-	enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[4],
-			      SB_T35_SMC911X_BASE, GPMC_SIZE_16M);
-
-	/* Enable off mode for NWE in PADCONF_GPMC_NWE register */
-	writew(readw(&ctrl_base->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
-
-	/* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
-	writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
-
-	/* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
-	writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
-		&ctrl_base->gpmc_nadv_ale);
-}
-
-#ifdef CONFIG_DRIVER_OMAP34XX_I2C
-/*
- * Routine: reset_net_chip
- * Description: reset the Ethernet controller via TPS65930 GPIO
- */
-static void reset_net_chip(void)
-{
-	/* Set GPIO1 of TPS65930 as output */
-	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
-				TWL4030_BASEADD_GPIO + 0x03);
-	/* Send a pulse on the GPIO pin */
-	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
-				TWL4030_BASEADD_GPIO + 0x0C);
-	udelay(1);
-	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
-				TWL4030_BASEADD_GPIO + 0x09);
-	mdelay(40);
-	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
-				TWL4030_BASEADD_GPIO + 0x0C);
-	mdelay(1);
-}
-#else
-static inline void reset_net_chip(void) {}
-#endif
-
-#ifdef CONFIG_SMC911X
-/*
- * Routine: handle_mac_address
- * Description: prepare MAC address for on-board Ethernet.
- */
-static int handle_mac_address(void)
-{
-	unsigned char enetaddr[6];
-	int rc;
-
-	rc = eth_getenv_enetaddr("ethaddr", enetaddr);
-	if (rc)
-		return 0;
-
-	rc = cm_t3x_eeprom_read_mac_addr(enetaddr);
-	if (rc)
-		return rc;
-
-	if (!is_valid_ether_addr(enetaddr))
-		return -1;
-
-	return eth_setenv_enetaddr("ethaddr", enetaddr);
-}
-
-
-/*
- * Routine: board_eth_init
- * Description: initialize module and base-board Ethernet chips
- */
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0, rc1 = 0;
-
-	setup_net_chip_gmpc();
-	reset_net_chip();
-
-	rc1 = handle_mac_address();
-	if (rc1)
-		printf("No MAC address found! ");
-
-	rc1 = smc911x_initialize(0, CM_T3X_SMC911X_BASE);
-	if (rc1 > 0)
-		rc++;
-
-	rc1 = smc911x_initialize(1, SB_T35_SMC911X_BASE);
-	if (rc1 > 0)
-		rc++;
-
-	return rc;
-}
-#endif
-
-void __weak get_board_serial(struct tag_serialnr *serialnr)
-{
-	/*
-	 * This corresponds to what happens when we can communicate with the
-	 * eeprom but don't get a valid board serial value.
-	 */
-	serialnr->low = 0;
-	serialnr->high = 0;
-};
-
-#ifdef CONFIG_USB_EHCI_OMAP
-struct omap_usbhs_board_data usbhs_bdata = {
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-};
-
-#define SB_T35_USB_HUB_RESET_GPIO	167
-int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
-{
-	u8 val;
-	int offset;
-
-	if (gpio_request(SB_T35_USB_HUB_RESET_GPIO, "SB-T35 usb hub reset")) {
-		printf("Error: can't obtain GPIO %d for SB-T35 usb hub reset",
-				SB_T35_USB_HUB_RESET_GPIO);
-		return -1;
-	}
-
-	gpio_direction_output(SB_T35_USB_HUB_RESET_GPIO, 0);
-	udelay(10);
-	gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
-	udelay(1000);
-
-	offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_GPIODATADIR1;
-	twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, &val, offset);
-	/* Set GPIO6 and GPIO7 of TPS65930 as output */
-	val |= 0xC0;
-	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, val, offset);
-	offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_SETGPIODATAOUT1;
-	/* Take both PHYs out of reset */
-	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0xC0, offset);
-	udelay(1);
-
-	return omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor);
-}
-
-int ehci_hcd_stop(void)
-{
-	return omap_ehci_hcd_stop();
-}
-
-#endif /* CONFIG_USB_EHCI_OMAP */
diff --git a/board/cm_t35/display.c b/board/cm_t35/display.c
deleted file mode 100644
index a004ea1d80..0000000000
--- a/board/cm_t35/display.c
+++ /dev/null
@@ -1,420 +0,0 @@
-/*
- * (C) Copyright 2012 CompuLab, Ltd. <www.compulab.co.il>
- *
- * Authors: Nikita Kiryanov <nikita@compulab.co.il>
- *
- * Parsing code based on linux/drivers/video/pxafb.c
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc.
- */
-#include <common.h>
-#include <asm/gpio.h>
-#include <asm/io.h>
-#include <stdio_dev.h>
-#include <asm/arch/dss.h>
-#include <lcd.h>
-#include <asm/arch-omap3/dss.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-enum display_type {
-	NONE,
-	DVI,
-	DVI_CUSTOM,
-};
-
-#define CMAP_ADDR	0x80100000
-
-/*
- * The frame buffer is allocated before we have the chance to parse user input.
- * To make sure enough memory is allocated for all resolutions, we define
- * vl_{col | row} to the maximal resolution supported by OMAP3.
- */
-vidinfo_t panel_info = {
-	.vl_col  = 1400,
-	.vl_row  = 1050,
-	.vl_bpix = LCD_BPP,
-	.cmap = (ushort *)CMAP_ADDR,
-};
-
-static struct panel_config panel_cfg;
-static enum display_type lcd_def;
-
-/*
- * A note on DVI presets;
- * U-Boot can convert 8 bit BMP data to 16 bit BMP data, and OMAP DSS can
- * convert 16 bit data into 24 bit data. Thus, GFXFORMAT_RGB16 allows us to
- * support two BMP types with one setting.
- */
-static const struct panel_config preset_dvi_640X480 = {
-	.lcd_size	= PANEL_LCD_SIZE(640, 480),
-	.timing_h	= DSS_HBP(48) | DSS_HFP(16) | DSS_HSW(96),
-	.timing_v	= DSS_VBP(33) | DSS_VFP(10) | DSS_VSW(2),
-	.divisor	= 12 | (1 << 16),
-	.data_lines	= LCD_INTERFACE_24_BIT,
-	.panel_type	= ACTIVE_DISPLAY,
-	.load_mode	= 2,
-	.gfx_format	= GFXFORMAT_RGB16,
-};
-
-static const struct panel_config preset_dvi_800X600 = {
-	.lcd_size	= PANEL_LCD_SIZE(800, 600),
-	.timing_h	= DSS_HBP(88) | DSS_HFP(40) | DSS_HSW(128),
-	.timing_v	= DSS_VBP(23) | DSS_VFP(1) | DSS_VSW(4),
-	.divisor	= 8 | (1 << 16),
-	.data_lines	= LCD_INTERFACE_24_BIT,
-	.panel_type	= ACTIVE_DISPLAY,
-	.load_mode	= 2,
-	.gfx_format	= GFXFORMAT_RGB16,
-};
-
-static const struct panel_config preset_dvi_1024X768 = {
-	.lcd_size	= PANEL_LCD_SIZE(1024, 768),
-	.timing_h	= DSS_HBP(160) | DSS_HFP(24) | DSS_HSW(136),
-	.timing_v	= DSS_VBP(29) | DSS_VFP(3) | DSS_VSW(6),
-	.divisor	= 5 | (1 << 16),
-	.data_lines	= LCD_INTERFACE_24_BIT,
-	.panel_type	= ACTIVE_DISPLAY,
-	.load_mode	= 2,
-	.gfx_format	= GFXFORMAT_RGB16,
-};
-
-static const struct panel_config preset_dvi_1152X864 = {
-	.lcd_size	= PANEL_LCD_SIZE(1152, 864),
-	.timing_h	= DSS_HBP(256) | DSS_HFP(64) | DSS_HSW(128),
-	.timing_v	= DSS_VBP(32) | DSS_VFP(1) | DSS_VSW(3),
-	.divisor	= 3 | (1 << 16),
-	.data_lines	= LCD_INTERFACE_24_BIT,
-	.panel_type	= ACTIVE_DISPLAY,
-	.load_mode	= 2,
-	.gfx_format	= GFXFORMAT_RGB16,
-};
-
-static const struct panel_config preset_dvi_1280X960 = {
-	.lcd_size	= PANEL_LCD_SIZE(1280, 960),
-	.timing_h	= DSS_HBP(312) | DSS_HFP(96) | DSS_HSW(112),
-	.timing_v	= DSS_VBP(36) | DSS_VFP(1) | DSS_VSW(3),
-	.divisor	= 3 | (1 << 16),
-	.data_lines	= LCD_INTERFACE_24_BIT,
-	.panel_type	= ACTIVE_DISPLAY,
-	.load_mode	= 2,
-	.gfx_format	= GFXFORMAT_RGB16,
-};
-
-static const struct panel_config preset_dvi_1280X1024 = {
-	.lcd_size	= PANEL_LCD_SIZE(1280, 1024),
-	.timing_h	= DSS_HBP(248) | DSS_HFP(48) | DSS_HSW(112),
-	.timing_v	= DSS_VBP(38) | DSS_VFP(1) | DSS_VSW(3),
-	.divisor	= 3 | (1 << 16),
-	.data_lines	= LCD_INTERFACE_24_BIT,
-	.panel_type	= ACTIVE_DISPLAY,
-	.load_mode	= 2,
-	.gfx_format	= GFXFORMAT_RGB16,
-};
-
-/*
- * set_resolution_params()
- *
- * Due to usage of multiple display related APIs resolution data is located in
- * more than one place. This function updates them all.
- */
-static void set_resolution_params(int x, int y)
-{
-	panel_cfg.lcd_size = PANEL_LCD_SIZE(x, y);
-	panel_info.vl_col = x;
-	panel_info.vl_row = y;
-	lcd_line_length = (panel_info.vl_col * NBITS(panel_info.vl_bpix)) / 8;
-}
-
-static void set_preset(const struct panel_config preset, int x_res, int y_res)
-{
-	panel_cfg = preset;
-	set_resolution_params(x_res, y_res);
-}
-
-static enum display_type set_dvi_preset(const struct panel_config preset,
-					int x_res, int y_res)
-{
-	set_preset(preset, x_res, y_res);
-	return DVI;
-}
-
-/*
- * parse_mode() - parse the mode parameter of custom lcd settings
- *
- * @mode:	<res_x>x<res_y>
- *
- * Returns -1 on error, 0 on success.
- */
-static int parse_mode(const char *mode)
-{
-	unsigned int modelen = strlen(mode);
-	int res_specified = 0;
-	unsigned int xres = 0, yres = 0;
-	int yres_specified = 0;
-	int i;
-
-	for (i = modelen - 1; i >= 0; i--) {
-		switch (mode[i]) {
-		case 'x':
-			if (!yres_specified) {
-				yres = simple_strtoul(&mode[i + 1], NULL, 0);
-				yres_specified = 1;
-			} else {
-				goto done_parsing;
-			}
-
-			break;
-		case '0' ... '9':
-			break;
-		default:
-			goto done_parsing;
-		}
-	}
-
-	if (i < 0 && yres_specified) {
-		xres = simple_strtoul(mode, NULL, 0);
-		res_specified = 1;
-	}
-
-done_parsing:
-	if (res_specified) {
-		set_resolution_params(xres, yres);
-	} else {
-		printf("LCD: invalid mode: %s\n", mode);
-		return -1;
-	}
-
-	return 0;
-}
-
-#define PIXEL_CLK_NUMERATOR (26 * 432 / 39)
-/*
- * parse_pixclock() - Parse the pixclock parameter of custom lcd settings
- *
- * @pixclock:	the desired pixel clock
- *
- * Returns -1 on error, 0 on success.
- *
- * Handling the pixel_clock:
- *
- * Pixel clock is defined in the OMAP35x TRM as follows:
- * pixel_clock =
- * (SYS_CLK * 2 * PRCM.CM_CLKSEL2_PLL[18:8]) /
- * (DSS.DISPC_DIVISOR[23:16] * DSS.DISPC_DIVISOR[6:0] *
- * PRCM.CM_CLKSEL_DSS[4:0] * (PRCM.CM_CLKSEL2_PLL[6:0] + 1))
- *
- * In practice, this means that in order to set the
- * divisor for the desired pixel clock one needs to
- * solve the following equation:
- *
- * 26 * 432 / (39 * <pixel_clock>) = DSS.DISPC_DIVISOR[6:0]
- *
- * NOTE: the explicit equation above is reduced. Do not
- * try to infer anything from these numbers.
- */
-static int parse_pixclock(char *pixclock)
-{
-	int divisor, pixclock_val;
-	char *pixclk_start = pixclock;
-
-	pixclock_val = simple_strtoul(pixclock, &pixclock, 10);
-	divisor = DIV_ROUND_UP(PIXEL_CLK_NUMERATOR, pixclock_val);
-	/* 0 and 1 are illegal values for PCD */
-	if (divisor <= 1)
-		divisor = 2;
-
-	panel_cfg.divisor = divisor | (1 << 16);
-	if (pixclock[0] != '\0') {
-		printf("LCD: invalid value for pixclock:%s\n", pixclk_start);
-		return -1;
-	}
-
-	return 0;
-}
-
-/*
- * parse_setting() - parse a single setting of custom lcd parameters
- *
- * @setting:	The custom lcd setting <name>:<value>
- *
- * Returns -1 on failure, 0 on success.
- */
-static int parse_setting(char *setting)
-{
-	int num_val;
-	char *setting_start = setting;
-
-	if (!strncmp(setting, "mode:", 5)) {
-		return parse_mode(setting + 5);
-	} else if (!strncmp(setting, "pixclock:", 9)) {
-		return parse_pixclock(setting + 9);
-	} else if (!strncmp(setting, "left:", 5)) {
-		num_val = simple_strtoul(setting + 5, &setting, 0);
-		panel_cfg.timing_h |= DSS_HBP(num_val);
-	} else if (!strncmp(setting, "right:", 6)) {
-		num_val = simple_strtoul(setting + 6, &setting, 0);
-		panel_cfg.timing_h |= DSS_HFP(num_val);
-	} else if (!strncmp(setting, "upper:", 6)) {
-		num_val = simple_strtoul(setting + 6, &setting, 0);
-		panel_cfg.timing_v |= DSS_VBP(num_val);
-	} else if (!strncmp(setting, "lower:", 6)) {
-		num_val = simple_strtoul(setting + 6, &setting, 0);
-		panel_cfg.timing_v |= DSS_VFP(num_val);
-	} else if (!strncmp(setting, "hsynclen:", 9)) {
-		num_val = simple_strtoul(setting + 9, &setting, 0);
-		panel_cfg.timing_h |= DSS_HSW(num_val);
-	} else if (!strncmp(setting, "vsynclen:", 9)) {
-		num_val = simple_strtoul(setting + 9, &setting, 0);
-		panel_cfg.timing_v |= DSS_VSW(num_val);
-	} else if (!strncmp(setting, "hsync:", 6)) {
-		if (simple_strtoul(setting + 6, &setting, 0) == 0)
-			panel_cfg.pol_freq |= DSS_IHS;
-		else
-			panel_cfg.pol_freq &= ~DSS_IHS;
-	} else if (!strncmp(setting, "vsync:", 6)) {
-		if (simple_strtoul(setting + 6, &setting, 0) == 0)
-			panel_cfg.pol_freq |= DSS_IVS;
-		else
-			panel_cfg.pol_freq &= ~DSS_IVS;
-	} else if (!strncmp(setting, "outputen:", 9)) {
-		if (simple_strtoul(setting + 9, &setting, 0) == 0)
-			panel_cfg.pol_freq |= DSS_IEO;
-		else
-			panel_cfg.pol_freq &= ~DSS_IEO;
-	} else if (!strncmp(setting, "pixclockpol:", 12)) {
-		if (simple_strtoul(setting + 12, &setting, 0) == 0)
-			panel_cfg.pol_freq |= DSS_IPC;
-		else
-			panel_cfg.pol_freq &= ~DSS_IPC;
-	} else if (!strncmp(setting, "active", 6)) {
-		panel_cfg.panel_type = ACTIVE_DISPLAY;
-		return 0; /* Avoid sanity check below */
-	} else if (!strncmp(setting, "passive", 7)) {
-		panel_cfg.panel_type = PASSIVE_DISPLAY;
-		return 0; /* Avoid sanity check below */
-	} else if (!strncmp(setting, "display:", 8)) {
-		if (!strncmp(setting + 8, "dvi", 3)) {
-			lcd_def = DVI_CUSTOM;
-			return 0; /* Avoid sanity check below */
-		}
-	} else {
-		printf("LCD: unknown option %s\n", setting_start);
-		return -1;
-	}
-
-	if (setting[0] != '\0') {
-		printf("LCD: invalid value for %s\n", setting_start);
-		return -1;
-	}
-
-	return 0;
-}
-
-/*
- * env_parse_customlcd() - parse custom lcd params from an environment variable.
- *
- * @custom_lcd_params:	The environment variable containing the lcd params.
- *
- * Returns -1 on failure, 0 on success.
- */
-static int parse_customlcd(char *custom_lcd_params)
-{
-	char params_cpy[160];
-	char *setting;
-
-	strncpy(params_cpy, custom_lcd_params, 160);
-	setting = strtok(params_cpy, ",");
-	while (setting) {
-		if (parse_setting(setting) < 0)
-			return -1;
-
-		setting = strtok(NULL, ",");
-	}
-
-	/* Currently we don't support changing this via custom lcd params */
-	panel_cfg.data_lines = LCD_INTERFACE_24_BIT;
-	panel_cfg.gfx_format = GFXFORMAT_RGB16; /* See dvi predefines note */
-
-	return 0;
-}
-
-/*
- * env_parse_displaytype() - parse display type.
- *
- * Parses the environment variable "displaytype", which contains the
- * name of the display type or preset, in which case it applies its
- * configurations.
- *
- * Returns the type of display that was specified.
- */
-static enum display_type env_parse_displaytype(char *displaytype)
-{
-	if (!strncmp(displaytype, "dvi640x480", 10))
-		return set_dvi_preset(preset_dvi_640X480, 640, 480);
-	else if (!strncmp(displaytype, "dvi800x600", 10))
-		return set_dvi_preset(preset_dvi_800X600, 800, 600);
-	else if (!strncmp(displaytype, "dvi1024x768", 11))
-		return set_dvi_preset(preset_dvi_1024X768, 1024, 768);
-	else if (!strncmp(displaytype, "dvi1152x864", 11))
-		return set_dvi_preset(preset_dvi_1152X864, 1152, 864);
-	else if (!strncmp(displaytype, "dvi1280x960", 11))
-		return set_dvi_preset(preset_dvi_1280X960, 1280, 960);
-	else if (!strncmp(displaytype, "dvi1280x1024", 12))
-		return set_dvi_preset(preset_dvi_1280X1024, 1280, 1024);
-
-	return NONE;
-}
-
-void lcd_ctrl_init(void *lcdbase)
-{
-	struct prcm *prcm = (struct prcm *)PRCM_BASE;
-	char *custom_lcd;
-	char *displaytype = getenv("displaytype");
-
-	if (displaytype == NULL)
-		return;
-
-	lcd_def = env_parse_displaytype(displaytype);
-	/* If we did not recognize the preset, check if it's an env variable */
-	if (lcd_def == NONE) {
-		custom_lcd = getenv(displaytype);
-		if (custom_lcd == NULL || parse_customlcd(custom_lcd) < 0)
-			return;
-	}
-
-	panel_cfg.frame_buffer = lcdbase;
-	omap3_dss_panel_config(&panel_cfg);
-	/*
-	 * Pixel clock is defined with many divisions and only few
-	 * multiplications of the system clock. Since DSS FCLK divisor is set
-	 * to 16 by default, we need to set it to a smaller value, like 3
-	 * (chosen via trial and error).
-	 */
-	clrsetbits_le32(&prcm->clksel_dss, 0xF, 3);
-}
-
-void lcd_enable(void)
-{
-	if (lcd_def == DVI || lcd_def == DVI_CUSTOM) {
-		gpio_direction_output(54, 0); /* Turn on DVI */
-		omap3_dss_enable();
-	}
-}
-
-void lcd_setcolreg(ushort regno, ushort red, ushort green, ushort blue) {}
diff --git a/board/cm_t35/eeprom.c b/board/cm_t35/eeprom.c
deleted file mode 100644
index b0af103cdd..0000000000
--- a/board/cm_t35/eeprom.c
+++ /dev/null
@@ -1,130 +0,0 @@
-/*
- * (C) Copyright 2011 CompuLab, Ltd. <www.compulab.co.il>
- *
- * Authors: Nikita Kiryanov <nikita@compulab.co.il>
- *	    Igor Grinberg <grinberg@compulab.co.il>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc.
- */
-
-#include <common.h>
-#include <i2c.h>
-
-#define EEPROM_LAYOUT_VER_OFFSET	44
-#define BOARD_SERIAL_OFFSET		20
-#define BOARD_SERIAL_OFFSET_LEGACY	8
-#define BOARD_REV_OFFSET		0
-#define BOARD_REV_OFFSET_LEGACY		6
-#define BOARD_REV_SIZE			2
-#define MAC_ADDR_OFFSET			4
-#define MAC_ADDR_OFFSET_LEGACY		0
-
-#define LAYOUT_INVALID	0
-#define LAYOUT_LEGACY	0xff
-
-static int eeprom_layout; /* Implicitly LAYOUT_INVALID */
-
-static int cm_t3x_eeprom_read(uint offset, uchar *buf, int len)
-{
-	return i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, offset,
-			CONFIG_SYS_I2C_EEPROM_ADDR_LEN, buf, len);
-}
-
-static int eeprom_setup_layout(void)
-{
-	int res;
-
-	if (eeprom_layout != LAYOUT_INVALID)
-		return 0;
-
-	res = cm_t3x_eeprom_read(EEPROM_LAYOUT_VER_OFFSET,
-						(uchar *)&eeprom_layout, 1);
-	if (res) {
-		eeprom_layout = LAYOUT_INVALID;
-		return res;
-	}
-
-	if (eeprom_layout == 0 || eeprom_layout >= 0x20)
-		eeprom_layout = LAYOUT_LEGACY;
-
-	return 0;
-}
-
-void get_board_serial(struct tag_serialnr *serialnr)
-{
-	u32 serial[2];
-	uint offset;
-
-	memset(serialnr, 0, sizeof(*serialnr));
-	if (eeprom_setup_layout())
-		return;
-
-	offset = (eeprom_layout != LAYOUT_LEGACY) ?
-			BOARD_SERIAL_OFFSET : BOARD_SERIAL_OFFSET_LEGACY;
-	if (cm_t3x_eeprom_read(offset, (uchar *)serial, 8))
-		return;
-
-	if (serial[0] != 0xffffffff && serial[1] != 0xffffffff) {
-		serialnr->low = serial[0];
-		serialnr->high = serial[1];
-	}
-}
-
-/*
- * Routine: cm_t3x_eeprom_read_mac_addr
- * Description: read mac address and store it in buf.
- */
-int cm_t3x_eeprom_read_mac_addr(uchar *buf)
-{
-	uint offset;
-
-	if (eeprom_setup_layout())
-		return 0;
-
-	offset = (eeprom_layout != LAYOUT_LEGACY) ?
-			MAC_ADDR_OFFSET : MAC_ADDR_OFFSET_LEGACY;
-	return cm_t3x_eeprom_read(offset, buf, 6);
-}
-
-/*
- * Routine: cm_t3x_eeprom_get_board_rev
- * Description: read system revision from eeprom
- */
-u32 cm_t3x_eeprom_get_board_rev(void)
-{
-	u32 rev = 0;
-	char str[5]; /* Legacy representation can contain at most 4 digits */
-	uint offset = BOARD_REV_OFFSET_LEGACY;
-
-	if (eeprom_setup_layout())
-		return 0;
-
-	if (eeprom_layout != LAYOUT_LEGACY)
-		offset = BOARD_REV_OFFSET;
-
-	if (cm_t3x_eeprom_read(offset, (uchar *)&rev, BOARD_REV_SIZE))
-		return 0;
-
-	/*
-	 * Convert legacy syntactic representation to semantic
-	 * representation. i.e. for rev 1.00: 0x100 --> 0x64
-	 */
-	if (eeprom_layout == LAYOUT_LEGACY) {
-		sprintf(str, "%x", rev);
-		rev = simple_strtoul(str, NULL, 10);
-	}
-
-	return rev;
-};
diff --git a/board/cm_t35/eeprom.h b/board/cm_t35/eeprom.h
deleted file mode 100644
index 38824d162b..0000000000
--- a/board/cm_t35/eeprom.h
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
- * (C) Copyright 2011 CompuLab, Ltd. <www.compulab.co.il>
- *
- * Authors: Nikita Kiryanov <nikita@compulab.co.il>
- *	    Igor Grinberg <grinberg@compulab.co.il>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc.
- */
-#ifndef _EEPROM_
-#define _EEPROM_
-
-#ifdef CONFIG_DRIVER_OMAP34XX_I2C
-int cm_t3x_eeprom_read_mac_addr(uchar *buf);
-u32 cm_t3x_eeprom_get_board_rev(void);
-#else
-static inline int cm_t3x_eeprom_read_mac_addr(uchar *buf)
-{
-	return 1;
-}
-static inline u32 cm_t3x_eeprom_get_board_rev(void)
-{
-	return 0;
-}
-#endif
-
-#endif
diff --git a/board/cm_t35/leds.c b/board/cm_t35/leds.c
deleted file mode 100644
index 48ad598d90..0000000000
--- a/board/cm_t35/leds.c
+++ /dev/null
@@ -1,45 +0,0 @@
-/*
- * (C) Copyright 2011
- * CompuLab, Ltd. <www.compulab.co.il>
- *
- * Author: Igor Grinberg <grinberg@compulab.co.il>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc.
- */
-#include <common.h>
-#include <status_led.h>
-#include <asm/gpio.h>
-
-static unsigned int leds[] = { GREEN_LED_GPIO };
-
-void __led_init(led_id_t mask, int state)
-{
-	if (gpio_request(leds[mask], "") != 0) {
-		printf("%s: failed requesting GPIO%u\n", __func__, leds[mask]);
-		return;
-	}
-
-	gpio_direction_output(leds[mask], 0);
-}
-
-void __led_set(led_id_t mask, int state)
-{
-	gpio_set_value(leds[mask], state == STATUS_LED_ON);
-}
-
-void __led_toggle(led_id_t mask)
-{
-	gpio_set_value(leds[mask], !gpio_get_value(leds[mask]));
-}
diff --git a/board/compulab/cm_t35/Makefile b/board/compulab/cm_t35/Makefile
new file mode 100644
index 0000000000..31d9bbbfe3
--- /dev/null
+++ b/board/compulab/cm_t35/Makefile
@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2011 - 2013 CompuLab, Ltd. <www.compulab.co.il>
+#
+# Authors: Nikita Kiryanov <nikita@compulab.co.il>
+#	   Igor Grinberg <grinberg@compulab.co.il>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc.
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-$(CONFIG_DRIVER_OMAP34XX_I2C) += eeprom.o
+COBJS-$(CONFIG_LCD) += display.o
+
+COBJS	:= cm_t35.o leds.o $(COBJS-y)
+
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/compulab/cm_t35/cm_t35.c b/board/compulab/cm_t35/cm_t35.c
new file mode 100644
index 0000000000..b0b80e5bc9
--- /dev/null
+++ b/board/compulab/cm_t35/cm_t35.c
@@ -0,0 +1,617 @@
+/*
+ * (C) Copyright 2011 - 2013 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Authors: Mike Rapoport <mike@compulab.co.il>
+ *	    Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * Derived from omap3evm and Beagle Board by
+ *	Manikandan Pillai <mani.pillai@ti.com>
+ *	Richard Woodruff <r-woodruff2@ti.com>
+ *	Syed Mohammed Khasim <x0khasim@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#include <common.h>
+#include <status_led.h>
+#include <netdev.h>
+#include <net.h>
+#include <i2c.h>
+#include <usb.h>
+#include <mmc.h>
+#include <nand.h>
+#include <twl4030.h>
+#include <bmp_layout.h>
+#include <linux/compiler.h>
+
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-types.h>
+#include <asm/ehci-omap.h>
+#include <asm/gpio.h>
+
+#include "eeprom.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+const omap3_sysinfo sysinfo = {
+	DDR_DISCRETE,
+	"CM-T3x board",
+	"NAND",
+};
+
+static u32 gpmc_net_config[GPMC_MAX_REG] = {
+	NET_GPMC_CONFIG1,
+	NET_GPMC_CONFIG2,
+	NET_GPMC_CONFIG3,
+	NET_GPMC_CONFIG4,
+	NET_GPMC_CONFIG5,
+	NET_GPMC_CONFIG6,
+	0
+};
+
+static u32 gpmc_nand_config[GPMC_MAX_REG] = {
+	SMNAND_GPMC_CONFIG1,
+	SMNAND_GPMC_CONFIG2,
+	SMNAND_GPMC_CONFIG3,
+	SMNAND_GPMC_CONFIG4,
+	SMNAND_GPMC_CONFIG5,
+	SMNAND_GPMC_CONFIG6,
+	0,
+};
+
+#ifdef CONFIG_LCD
+#ifdef CONFIG_CMD_NAND
+static int splash_load_from_nand(u32 bmp_load_addr)
+{
+	struct bmp_header *bmp_hdr;
+	int res, splash_screen_nand_offset = 0x100000;
+	size_t bmp_size, bmp_header_size = sizeof(struct bmp_header);
+
+	if (bmp_load_addr + bmp_header_size >= gd->start_addr_sp)
+		goto splash_address_too_high;
+
+	res = nand_read_skip_bad(&nand_info[nand_curr_device],
+			splash_screen_nand_offset, &bmp_header_size,
+			NULL, nand_info[nand_curr_device].size,
+			(u_char *)bmp_load_addr);
+	if (res < 0)
+		return res;
+
+	bmp_hdr = (struct bmp_header *)bmp_load_addr;
+	bmp_size = le32_to_cpu(bmp_hdr->file_size);
+
+	if (bmp_load_addr + bmp_size >= gd->start_addr_sp)
+		goto splash_address_too_high;
+
+	return nand_read_skip_bad(&nand_info[nand_curr_device],
+			splash_screen_nand_offset, &bmp_size,
+			NULL, nand_info[nand_curr_device].size,
+			(u_char *)bmp_load_addr);
+
+splash_address_too_high:
+	printf("Error: splashimage address too high. Data overwrites U-Boot "
+		"and/or placed beyond DRAM boundaries.\n");
+
+	return -1;
+}
+#else
+static inline int splash_load_from_nand(void)
+{
+	return -1;
+}
+#endif /* CONFIG_CMD_NAND */
+
+int board_splash_screen_prepare(void)
+{
+	char *env_splashimage_value;
+	u32 bmp_load_addr;
+
+	env_splashimage_value = getenv("splashimage");
+	if (env_splashimage_value == NULL)
+		return -1;
+
+	bmp_load_addr = simple_strtoul(env_splashimage_value, 0, 16);
+	if (bmp_load_addr == 0) {
+		printf("Error: bad splashimage address specified\n");
+		return -1;
+	}
+
+	return splash_load_from_nand(bmp_load_addr);
+}
+#endif /* CONFIG_LCD */
+
+/*
+ * Routine: board_init
+ * Description: hardware init.
+ */
+int board_init(void)
+{
+	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+
+	enable_gpmc_cs_config(gpmc_nand_config, &gpmc_cfg->cs[0],
+			      CONFIG_SYS_NAND_BASE, GPMC_SIZE_16M);
+
+	/* board id for Linux */
+	if (get_cpu_family() == CPU_OMAP34XX)
+		gd->bd->bi_arch_number = MACH_TYPE_CM_T35;
+	else
+		gd->bd->bi_arch_number = MACH_TYPE_CM_T3730;
+
+	/* boot param addr */
+	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
+	status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
+#endif
+
+	return 0;
+}
+
+static u32 cm_t3x_rev;
+
+/*
+ * Routine: get_board_rev
+ * Description: read system revision
+ */
+u32 get_board_rev(void)
+{
+	if (!cm_t3x_rev)
+		cm_t3x_rev = cm_t3x_eeprom_get_board_rev();
+
+	return cm_t3x_rev;
+};
+
+/*
+ * Routine: misc_init_r
+ * Description: display die ID
+ */
+int misc_init_r(void)
+{
+	u32 board_rev = get_board_rev();
+	u32 rev_major = board_rev / 100;
+	u32 rev_minor = board_rev - (rev_major * 100);
+
+	if ((rev_minor / 10) * 10 == rev_minor)
+		rev_minor = rev_minor / 10;
+
+	printf("PCB:   %u.%u\n", rev_major, rev_minor);
+	dieid_num_r();
+
+	return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ *		hardware. Many pins need to be moved from protect to primary
+ *		mode.
+ */
+static void cm_t3x_set_common_muxconf(void)
+{
+	/* SDRC */
+	MUX_VAL(CP(SDRC_D0),		(IEN  | PTD | DIS | M0)); /*SDRC_D0*/
+	MUX_VAL(CP(SDRC_D1),		(IEN  | PTD | DIS | M0)); /*SDRC_D1*/
+	MUX_VAL(CP(SDRC_D2),		(IEN  | PTD | DIS | M0)); /*SDRC_D2*/
+	MUX_VAL(CP(SDRC_D3),		(IEN  | PTD | DIS | M0)); /*SDRC_D3*/
+	MUX_VAL(CP(SDRC_D4),		(IEN  | PTD | DIS | M0)); /*SDRC_D4*/
+	MUX_VAL(CP(SDRC_D5),		(IEN  | PTD | DIS | M0)); /*SDRC_D5*/
+	MUX_VAL(CP(SDRC_D6),		(IEN  | PTD | DIS | M0)); /*SDRC_D6*/
+	MUX_VAL(CP(SDRC_D7),		(IEN  | PTD | DIS | M0)); /*SDRC_D7*/
+	MUX_VAL(CP(SDRC_D8),		(IEN  | PTD | DIS | M0)); /*SDRC_D8*/
+	MUX_VAL(CP(SDRC_D9),		(IEN  | PTD | DIS | M0)); /*SDRC_D9*/
+	MUX_VAL(CP(SDRC_D10),		(IEN  | PTD | DIS | M0)); /*SDRC_D10*/
+	MUX_VAL(CP(SDRC_D11),		(IEN  | PTD | DIS | M0)); /*SDRC_D11*/
+	MUX_VAL(CP(SDRC_D12),		(IEN  | PTD | DIS | M0)); /*SDRC_D12*/
+	MUX_VAL(CP(SDRC_D13),		(IEN  | PTD | DIS | M0)); /*SDRC_D13*/
+	MUX_VAL(CP(SDRC_D14),		(IEN  | PTD | DIS | M0)); /*SDRC_D14*/
+	MUX_VAL(CP(SDRC_D15),		(IEN  | PTD | DIS | M0)); /*SDRC_D15*/
+	MUX_VAL(CP(SDRC_D16),		(IEN  | PTD | DIS | M0)); /*SDRC_D16*/
+	MUX_VAL(CP(SDRC_D17),		(IEN  | PTD | DIS | M0)); /*SDRC_D17*/
+	MUX_VAL(CP(SDRC_D18),		(IEN  | PTD | DIS | M0)); /*SDRC_D18*/
+	MUX_VAL(CP(SDRC_D19),		(IEN  | PTD | DIS | M0)); /*SDRC_D19*/
+	MUX_VAL(CP(SDRC_D20),		(IEN  | PTD | DIS | M0)); /*SDRC_D20*/
+	MUX_VAL(CP(SDRC_D21),		(IEN  | PTD | DIS | M0)); /*SDRC_D21*/
+	MUX_VAL(CP(SDRC_D22),		(IEN  | PTD | DIS | M0)); /*SDRC_D22*/
+	MUX_VAL(CP(SDRC_D23),		(IEN  | PTD | DIS | M0)); /*SDRC_D23*/
+	MUX_VAL(CP(SDRC_D24),		(IEN  | PTD | DIS | M0)); /*SDRC_D24*/
+	MUX_VAL(CP(SDRC_D25),		(IEN  | PTD | DIS | M0)); /*SDRC_D25*/
+	MUX_VAL(CP(SDRC_D26),		(IEN  | PTD | DIS | M0)); /*SDRC_D26*/
+	MUX_VAL(CP(SDRC_D27),		(IEN  | PTD | DIS | M0)); /*SDRC_D27*/
+	MUX_VAL(CP(SDRC_D28),		(IEN  | PTD | DIS | M0)); /*SDRC_D28*/
+	MUX_VAL(CP(SDRC_D29),		(IEN  | PTD | DIS | M0)); /*SDRC_D29*/
+	MUX_VAL(CP(SDRC_D30),		(IEN  | PTD | DIS | M0)); /*SDRC_D30*/
+	MUX_VAL(CP(SDRC_D31),		(IEN  | PTD | DIS | M0)); /*SDRC_D31*/
+	MUX_VAL(CP(SDRC_CLK),		(IEN  | PTD | DIS | M0)); /*SDRC_CLK*/
+	MUX_VAL(CP(SDRC_DQS0),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS0*/
+	MUX_VAL(CP(SDRC_DQS1),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS1*/
+	MUX_VAL(CP(SDRC_DQS2),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS2*/
+	MUX_VAL(CP(SDRC_DQS3),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS3*/
+	MUX_VAL(CP(SDRC_CKE0),		(IDIS | PTU | EN  | M0)); /*SDRC_CKE0*/
+	MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTD | DIS | M7)); /*SDRC_CKE1*/
+
+	/* GPMC */
+	MUX_VAL(CP(GPMC_A1),		(IDIS | PTU | EN  | M0)); /*GPMC_A1*/
+	MUX_VAL(CP(GPMC_A2),		(IDIS | PTU | EN  | M0)); /*GPMC_A2*/
+	MUX_VAL(CP(GPMC_A3),		(IDIS | PTU | EN  | M0)); /*GPMC_A3*/
+	MUX_VAL(CP(GPMC_A4),		(IDIS | PTU | EN  | M0)); /*GPMC_A4*/
+	MUX_VAL(CP(GPMC_A5),		(IDIS | PTU | EN  | M0)); /*GPMC_A5*/
+	MUX_VAL(CP(GPMC_A6),		(IDIS | PTU | EN  | M0)); /*GPMC_A6*/
+	MUX_VAL(CP(GPMC_A7),		(IDIS | PTU | EN  | M0)); /*GPMC_A7*/
+	MUX_VAL(CP(GPMC_A8),		(IDIS | PTU | EN  | M0)); /*GPMC_A8*/
+	MUX_VAL(CP(GPMC_A9),		(IDIS | PTU | EN  | M0)); /*GPMC_A9*/
+	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | EN  | M0)); /*GPMC_A10*/
+	MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0)); /*GPMC_D0*/
+	MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0)); /*GPMC_D1*/
+	MUX_VAL(CP(GPMC_D2),		(IEN  | PTU | EN  | M0)); /*GPMC_D2*/
+	MUX_VAL(CP(GPMC_D3),		(IEN  | PTU | EN  | M0)); /*GPMC_D3*/
+	MUX_VAL(CP(GPMC_D4),		(IEN  | PTU | EN  | M0)); /*GPMC_D4*/
+	MUX_VAL(CP(GPMC_D5),		(IEN  | PTU | EN  | M0)); /*GPMC_D5*/
+	MUX_VAL(CP(GPMC_D6),		(IEN  | PTU | EN  | M0)); /*GPMC_D6*/
+	MUX_VAL(CP(GPMC_D7),		(IEN  | PTU | EN  | M0)); /*GPMC_D7*/
+	MUX_VAL(CP(GPMC_D8),		(IEN  | PTU | EN  | M0)); /*GPMC_D8*/
+	MUX_VAL(CP(GPMC_D9),		(IEN  | PTU | EN  | M0)); /*GPMC_D9*/
+	MUX_VAL(CP(GPMC_D10),		(IEN  | PTU | EN  | M0)); /*GPMC_D10*/
+	MUX_VAL(CP(GPMC_D11),		(IEN  | PTU | EN  | M0)); /*GPMC_D11*/
+	MUX_VAL(CP(GPMC_D12),		(IEN  | PTU | EN  | M0)); /*GPMC_D12*/
+	MUX_VAL(CP(GPMC_D13),		(IEN  | PTU | EN  | M0)); /*GPMC_D13*/
+	MUX_VAL(CP(GPMC_D14),		(IEN  | PTU | EN  | M0)); /*GPMC_D14*/
+	MUX_VAL(CP(GPMC_D15),		(IEN  | PTU | EN  | M0)); /*GPMC_D15*/
+	MUX_VAL(CP(GPMC_NCS0),		(IDIS | PTU | EN  | M0)); /*GPMC_nCS0*/
+
+	/* SB-T35 Ethernet */
+	MUX_VAL(CP(GPMC_NCS4),		(IEN  | PTU | EN  | M0)); /*GPMC_nCS4*/
+
+	/* DVI enable */
+	MUX_VAL(CP(GPMC_NCS3),		(IDIS  | PTU | DIS  | M4));/*GPMC_nCS3*/
+
+	/* CM-T3x Ethernet */
+	MUX_VAL(CP(GPMC_NCS5),		(IDIS | PTU | DIS | M0)); /*GPMC_nCS5*/
+	MUX_VAL(CP(GPMC_CLK),		(IEN  | PTD | DIS | M4)); /*GPIO_59*/
+	MUX_VAL(CP(GPMC_NADV_ALE),	(IDIS | PTD | DIS | M0)); /*nADV_ALE*/
+	MUX_VAL(CP(GPMC_NOE),		(IDIS | PTD | DIS | M0)); /*nOE*/
+	MUX_VAL(CP(GPMC_NWE),		(IDIS | PTD | DIS | M0)); /*nWE*/
+	MUX_VAL(CP(GPMC_NBE0_CLE),	(IDIS | PTU | EN  | M0)); /*nBE0_CLE*/
+	MUX_VAL(CP(GPMC_NBE1),		(IDIS | PTD | DIS | M4)); /*GPIO_61*/
+	MUX_VAL(CP(GPMC_NWP),		(IEN  | PTD | DIS | M0)); /*nWP*/
+	MUX_VAL(CP(GPMC_WAIT0),		(IEN  | PTU | EN  | M0)); /*WAIT0*/
+
+	/* DSS */
+	MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0)); /*DSS_PCLK*/
+	MUX_VAL(CP(DSS_HSYNC),		(IDIS | PTD | DIS | M0)); /*DSS_HSYNC*/
+	MUX_VAL(CP(DSS_VSYNC),		(IDIS | PTD | DIS | M0)); /*DSS_VSYNC*/
+	MUX_VAL(CP(DSS_ACBIAS),		(IDIS | PTD | DIS | M0)); /*DSS_ACBIAS*/
+	MUX_VAL(CP(DSS_DATA6),		(IDIS | PTD | DIS | M0)); /*DSS_DATA6*/
+	MUX_VAL(CP(DSS_DATA7),		(IDIS | PTD | DIS | M0)); /*DSS_DATA7*/
+	MUX_VAL(CP(DSS_DATA8),		(IDIS | PTD | DIS | M0)); /*DSS_DATA8*/
+	MUX_VAL(CP(DSS_DATA9),		(IDIS | PTD | DIS | M0)); /*DSS_DATA9*/
+	MUX_VAL(CP(DSS_DATA10),		(IDIS | PTD | DIS | M0)); /*DSS_DATA10*/
+	MUX_VAL(CP(DSS_DATA11),		(IDIS | PTD | DIS | M0)); /*DSS_DATA11*/
+	MUX_VAL(CP(DSS_DATA12),		(IDIS | PTD | DIS | M0)); /*DSS_DATA12*/
+	MUX_VAL(CP(DSS_DATA13),		(IDIS | PTD | DIS | M0)); /*DSS_DATA13*/
+	MUX_VAL(CP(DSS_DATA14),		(IDIS | PTD | DIS | M0)); /*DSS_DATA14*/
+	MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0)); /*DSS_DATA15*/
+	MUX_VAL(CP(DSS_DATA16),		(IDIS | PTD | DIS | M0)); /*DSS_DATA16*/
+	MUX_VAL(CP(DSS_DATA17),		(IDIS | PTD | DIS | M0)); /*DSS_DATA17*/
+
+	/* serial interface */
+	MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0)); /*UART3_RX*/
+	MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0)); /*UART3_TX*/
+
+	/* mUSB */
+	MUX_VAL(CP(HSUSB0_CLK),		(IEN  | PTD | DIS | M0)); /*HSUSB0_CLK*/
+	MUX_VAL(CP(HSUSB0_STP),		(IDIS | PTU | EN  | M0)); /*HSUSB0_STP*/
+	MUX_VAL(CP(HSUSB0_DIR),		(IEN  | PTD | DIS | M0)); /*HSUSB0_DIR*/
+	MUX_VAL(CP(HSUSB0_NXT),		(IEN  | PTD | DIS | M0)); /*HSUSB0_NXT*/
+	MUX_VAL(CP(HSUSB0_DATA0),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA0*/
+	MUX_VAL(CP(HSUSB0_DATA1),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA1*/
+	MUX_VAL(CP(HSUSB0_DATA2),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA2*/
+	MUX_VAL(CP(HSUSB0_DATA3),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA3*/
+	MUX_VAL(CP(HSUSB0_DATA4),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA4*/
+	MUX_VAL(CP(HSUSB0_DATA5),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA5*/
+	MUX_VAL(CP(HSUSB0_DATA6),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA6*/
+	MUX_VAL(CP(HSUSB0_DATA7),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA7*/
+
+	/* USB EHCI */
+	MUX_VAL(CP(ETK_D0_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT0*/
+	MUX_VAL(CP(ETK_D1_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT1*/
+	MUX_VAL(CP(ETK_D2_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT2*/
+	MUX_VAL(CP(ETK_D7_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT3*/
+	MUX_VAL(CP(ETK_D4_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT4*/
+	MUX_VAL(CP(ETK_D5_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT5*/
+	MUX_VAL(CP(ETK_D6_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT6*/
+	MUX_VAL(CP(ETK_D3_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT7*/
+	MUX_VAL(CP(ETK_D8_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DIR*/
+	MUX_VAL(CP(ETK_D9_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_NXT*/
+	MUX_VAL(CP(ETK_CTL_ES2),	(IDIS | PTD | DIS | M3)); /*HSUSB1_CLK*/
+	MUX_VAL(CP(ETK_CLK_ES2),	(IDIS | PTU | DIS | M3)); /*HSUSB1_STP*/
+
+	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT0*/
+	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT1*/
+	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT2*/
+	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT3*/
+	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT4*/
+	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT5*/
+	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT6*/
+	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT7*/
+	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DIR*/
+	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_NXT*/
+	MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)); /*HSUSB2_CLK*/
+	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | DIS | M3)); /*HSUSB2_STP*/
+
+	/* SB_T35_USB_HUB_RESET_GPIO */
+	MUX_VAL(CP(CAM_WEN),		(IDIS | PTD | DIS | M4)); /*GPIO_167*/
+
+	/* I2C1 */
+	MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0)); /*I2C1_SCL*/
+	MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0)); /*I2C1_SDA*/
+	/* I2C2 */
+	MUX_VAL(CP(I2C2_SCL),		(IEN  | PTU | EN  | M0)); /*I2C2_SCL*/
+	MUX_VAL(CP(I2C2_SDA),		(IEN  | PTU | EN  | M0)); /*I2C2_SDA*/
+	/* I2C3 */
+	MUX_VAL(CP(I2C3_SCL),		(IEN  | PTU | EN  | M0)); /*I2C3_SCL*/
+	MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0)); /*I2C3_SDA*/
+
+	/* control and debug */
+	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | DIS | M0)); /*SYS_32K*/
+	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)); /*SYS_CLKREQ*/
+	MUX_VAL(CP(SYS_NIRQ),		(IEN  | PTU | EN  | M0)); /*SYS_nIRQ*/
+	MUX_VAL(CP(SYS_OFF_MODE),	(IEN  | PTD | DIS | M0)); /*OFF_MODE*/
+	MUX_VAL(CP(SYS_CLKOUT1),	(IEN  | PTD | DIS | M0)); /*CLKOUT1*/
+	MUX_VAL(CP(SYS_CLKOUT2),	(IDIS | PTU | DIS | M4)); /*green LED*/
+	MUX_VAL(CP(JTAG_nTRST),		(IEN  | PTD | DIS | M0)); /*JTAG_nTRST*/
+	MUX_VAL(CP(JTAG_TCK),		(IEN  | PTD | DIS | M0)); /*JTAG_TCK*/
+	MUX_VAL(CP(JTAG_TMS),		(IEN  | PTD | DIS | M0)); /*JTAG_TMS*/
+	MUX_VAL(CP(JTAG_TDI),		(IEN  | PTD | DIS | M0)); /*JTAG_TDI*/
+
+	/* MMC1 */
+	MUX_VAL(CP(MMC1_CLK),		(IDIS | PTU | EN  | M0)); /*MMC1_CLK*/
+	MUX_VAL(CP(MMC1_CMD),		(IEN  | PTU | EN  | M0)); /*MMC1_CMD*/
+	MUX_VAL(CP(MMC1_DAT0),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT0*/
+	MUX_VAL(CP(MMC1_DAT1),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT1*/
+	MUX_VAL(CP(MMC1_DAT2),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT2*/
+	MUX_VAL(CP(MMC1_DAT3),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT3*/
+}
+
+static void cm_t35_set_muxconf(void)
+{
+	/* DSS */
+	MUX_VAL(CP(DSS_DATA0),		(IDIS | PTD | DIS | M0)); /*DSS_DATA0*/
+	MUX_VAL(CP(DSS_DATA1),		(IDIS | PTD | DIS | M0)); /*DSS_DATA1*/
+	MUX_VAL(CP(DSS_DATA2),		(IDIS | PTD | DIS | M0)); /*DSS_DATA2*/
+	MUX_VAL(CP(DSS_DATA3),		(IDIS | PTD | DIS | M0)); /*DSS_DATA3*/
+	MUX_VAL(CP(DSS_DATA4),		(IDIS | PTD | DIS | M0)); /*DSS_DATA4*/
+	MUX_VAL(CP(DSS_DATA5),		(IDIS | PTD | DIS | M0)); /*DSS_DATA5*/
+
+	MUX_VAL(CP(DSS_DATA18),         (IDIS | PTD | DIS | M0)); /*DSS_DATA18*/
+	MUX_VAL(CP(DSS_DATA19),         (IDIS | PTD | DIS | M0)); /*DSS_DATA19*/
+	MUX_VAL(CP(DSS_DATA20),         (IDIS | PTD | DIS | M0)); /*DSS_DATA20*/
+	MUX_VAL(CP(DSS_DATA21),         (IDIS | PTD | DIS | M0)); /*DSS_DATA21*/
+	MUX_VAL(CP(DSS_DATA22),         (IDIS | PTD | DIS | M0)); /*DSS_DATA22*/
+	MUX_VAL(CP(DSS_DATA23),         (IDIS | PTD | DIS | M0)); /*DSS_DATA23*/
+
+	/* MMC1 */
+	MUX_VAL(CP(MMC1_DAT4),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT4*/
+	MUX_VAL(CP(MMC1_DAT5),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT5*/
+	MUX_VAL(CP(MMC1_DAT6),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT6*/
+	MUX_VAL(CP(MMC1_DAT7),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT7*/
+}
+
+static void cm_t3730_set_muxconf(void)
+{
+	/* DSS */
+	MUX_VAL(CP(DSS_DATA18),		(IDIS | PTD | DIS | M3)); /*DSS_DATA0*/
+	MUX_VAL(CP(DSS_DATA19),		(IDIS | PTD | DIS | M3)); /*DSS_DATA1*/
+	MUX_VAL(CP(DSS_DATA20),		(IDIS | PTD | DIS | M3)); /*DSS_DATA2*/
+	MUX_VAL(CP(DSS_DATA21),		(IDIS | PTD | DIS | M3)); /*DSS_DATA3*/
+	MUX_VAL(CP(DSS_DATA22),		(IDIS | PTD | DIS | M3)); /*DSS_DATA4*/
+	MUX_VAL(CP(DSS_DATA23),		(IDIS | PTD | DIS | M3)); /*DSS_DATA5*/
+
+	MUX_VAL(CP(SYS_BOOT0),		(IDIS | PTD | DIS | M3)); /*DSS_DATA18*/
+	MUX_VAL(CP(SYS_BOOT1),		(IDIS | PTD | DIS | M3)); /*DSS_DATA19*/
+	MUX_VAL(CP(SYS_BOOT3),		(IDIS | PTD | DIS | M3)); /*DSS_DATA20*/
+	MUX_VAL(CP(SYS_BOOT4),		(IDIS | PTD | DIS | M3)); /*DSS_DATA21*/
+	MUX_VAL(CP(SYS_BOOT5),		(IDIS | PTD | DIS | M3)); /*DSS_DATA22*/
+	MUX_VAL(CP(SYS_BOOT6),		(IDIS | PTD | DIS | M3)); /*DSS_DATA23*/
+}
+
+void set_muxconf_regs(void)
+{
+	cm_t3x_set_common_muxconf();
+
+	if (get_cpu_family() == CPU_OMAP34XX)
+		cm_t35_set_muxconf();
+	else
+		cm_t3730_set_muxconf();
+}
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_getcd(struct mmc *mmc)
+{
+	u8 val;
+
+	if (twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO, &val))
+		return -1;
+
+	return !(val & 1);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	return omap_mmc_init(0, 0, 0, -1, 59);
+}
+#endif
+
+/*
+ * Routine: setup_net_chip_gmpc
+ * Description: Setting up the configuration GPMC registers specific to the
+ *		Ethernet hardware.
+ */
+static void setup_net_chip_gmpc(void)
+{
+	struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
+
+	enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[5],
+			      CM_T3X_SMC911X_BASE, GPMC_SIZE_16M);
+	enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[4],
+			      SB_T35_SMC911X_BASE, GPMC_SIZE_16M);
+
+	/* Enable off mode for NWE in PADCONF_GPMC_NWE register */
+	writew(readw(&ctrl_base->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
+
+	/* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
+	writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
+
+	/* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
+	writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
+		&ctrl_base->gpmc_nadv_ale);
+}
+
+#ifdef CONFIG_DRIVER_OMAP34XX_I2C
+/*
+ * Routine: reset_net_chip
+ * Description: reset the Ethernet controller via TPS65930 GPIO
+ */
+static void reset_net_chip(void)
+{
+	/* Set GPIO1 of TPS65930 as output */
+	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x03,
+			     0x02);
+	/* Send a pulse on the GPIO pin */
+	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x0C,
+			     0x02);
+	udelay(1);
+	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x09,
+			     0x02);
+	mdelay(40);
+	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x0C,
+			     0x02);
+	mdelay(1);
+}
+#else
+static inline void reset_net_chip(void) {}
+#endif
+
+#ifdef CONFIG_SMC911X
+/*
+ * Routine: handle_mac_address
+ * Description: prepare MAC address for on-board Ethernet.
+ */
+static int handle_mac_address(void)
+{
+	unsigned char enetaddr[6];
+	int rc;
+
+	rc = eth_getenv_enetaddr("ethaddr", enetaddr);
+	if (rc)
+		return 0;
+
+	rc = cm_t3x_eeprom_read_mac_addr(enetaddr);
+	if (rc)
+		return rc;
+
+	if (!is_valid_ether_addr(enetaddr))
+		return -1;
+
+	return eth_setenv_enetaddr("ethaddr", enetaddr);
+}
+
+
+/*
+ * Routine: board_eth_init
+ * Description: initialize module and base-board Ethernet chips
+ */
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0, rc1 = 0;
+
+	setup_net_chip_gmpc();
+	reset_net_chip();
+
+	rc1 = handle_mac_address();
+	if (rc1)
+		printf("No MAC address found! ");
+
+	rc1 = smc911x_initialize(0, CM_T3X_SMC911X_BASE);
+	if (rc1 > 0)
+		rc++;
+
+	rc1 = smc911x_initialize(1, SB_T35_SMC911X_BASE);
+	if (rc1 > 0)
+		rc++;
+
+	return rc;
+}
+#endif
+
+void __weak get_board_serial(struct tag_serialnr *serialnr)
+{
+	/*
+	 * This corresponds to what happens when we can communicate with the
+	 * eeprom but don't get a valid board serial value.
+	 */
+	serialnr->low = 0;
+	serialnr->high = 0;
+};
+
+#ifdef CONFIG_USB_EHCI_OMAP
+struct omap_usbhs_board_data usbhs_bdata = {
+	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
+
+#define SB_T35_USB_HUB_RESET_GPIO	167
+int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+	u8 val;
+	int offset;
+
+	if (gpio_request(SB_T35_USB_HUB_RESET_GPIO, "SB-T35 usb hub reset")) {
+		printf("Error: can't obtain GPIO %d for SB-T35 usb hub reset",
+				SB_T35_USB_HUB_RESET_GPIO);
+		return -1;
+	}
+
+	gpio_direction_output(SB_T35_USB_HUB_RESET_GPIO, 0);
+	udelay(10);
+	gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
+	udelay(1000);
+
+	offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_GPIODATADIR1;
+	twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, offset, &val);
+	/* Set GPIO6 and GPIO7 of TPS65930 as output */
+	val |= 0xC0;
+	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, offset, val);
+	offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_SETGPIODATAOUT1;
+	/* Take both PHYs out of reset */
+	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, offset, 0xC0);
+	udelay(1);
+
+	return omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor);
+}
+
+int ehci_hcd_stop(void)
+{
+	return omap_ehci_hcd_stop();
+}
+
+#endif /* CONFIG_USB_EHCI_OMAP */
diff --git a/board/compulab/cm_t35/display.c b/board/compulab/cm_t35/display.c
new file mode 100644
index 0000000000..adc485365c
--- /dev/null
+++ b/board/compulab/cm_t35/display.c
@@ -0,0 +1,420 @@
+/*
+ * (C) Copyright 2012 - 2013 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Authors: Nikita Kiryanov <nikita@compulab.co.il>
+ *
+ * Parsing code based on linux/drivers/video/pxafb.c
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <stdio_dev.h>
+#include <asm/arch/dss.h>
+#include <lcd.h>
+#include <asm/arch-omap3/dss.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+enum display_type {
+	NONE,
+	DVI,
+	DVI_CUSTOM,
+};
+
+#define CMAP_ADDR	0x80100000
+
+/*
+ * The frame buffer is allocated before we have the chance to parse user input.
+ * To make sure enough memory is allocated for all resolutions, we define
+ * vl_{col | row} to the maximal resolution supported by OMAP3.
+ */
+vidinfo_t panel_info = {
+	.vl_col  = 1400,
+	.vl_row  = 1050,
+	.vl_bpix = LCD_BPP,
+	.cmap = (ushort *)CMAP_ADDR,
+};
+
+static struct panel_config panel_cfg;
+static enum display_type lcd_def;
+
+/*
+ * A note on DVI presets;
+ * U-Boot can convert 8 bit BMP data to 16 bit BMP data, and OMAP DSS can
+ * convert 16 bit data into 24 bit data. Thus, GFXFORMAT_RGB16 allows us to
+ * support two BMP types with one setting.
+ */
+static const struct panel_config preset_dvi_640X480 = {
+	.lcd_size	= PANEL_LCD_SIZE(640, 480),
+	.timing_h	= DSS_HBP(48) | DSS_HFP(16) | DSS_HSW(96),
+	.timing_v	= DSS_VBP(33) | DSS_VFP(10) | DSS_VSW(2),
+	.divisor	= 12 | (1 << 16),
+	.data_lines	= LCD_INTERFACE_24_BIT,
+	.panel_type	= ACTIVE_DISPLAY,
+	.load_mode	= 2,
+	.gfx_format	= GFXFORMAT_RGB16,
+};
+
+static const struct panel_config preset_dvi_800X600 = {
+	.lcd_size	= PANEL_LCD_SIZE(800, 600),
+	.timing_h	= DSS_HBP(88) | DSS_HFP(40) | DSS_HSW(128),
+	.timing_v	= DSS_VBP(23) | DSS_VFP(1) | DSS_VSW(4),
+	.divisor	= 8 | (1 << 16),
+	.data_lines	= LCD_INTERFACE_24_BIT,
+	.panel_type	= ACTIVE_DISPLAY,
+	.load_mode	= 2,
+	.gfx_format	= GFXFORMAT_RGB16,
+};
+
+static const struct panel_config preset_dvi_1024X768 = {
+	.lcd_size	= PANEL_LCD_SIZE(1024, 768),
+	.timing_h	= DSS_HBP(160) | DSS_HFP(24) | DSS_HSW(136),
+	.timing_v	= DSS_VBP(29) | DSS_VFP(3) | DSS_VSW(6),
+	.divisor	= 5 | (1 << 16),
+	.data_lines	= LCD_INTERFACE_24_BIT,
+	.panel_type	= ACTIVE_DISPLAY,
+	.load_mode	= 2,
+	.gfx_format	= GFXFORMAT_RGB16,
+};
+
+static const struct panel_config preset_dvi_1152X864 = {
+	.lcd_size	= PANEL_LCD_SIZE(1152, 864),
+	.timing_h	= DSS_HBP(256) | DSS_HFP(64) | DSS_HSW(128),
+	.timing_v	= DSS_VBP(32) | DSS_VFP(1) | DSS_VSW(3),
+	.divisor	= 3 | (1 << 16),
+	.data_lines	= LCD_INTERFACE_24_BIT,
+	.panel_type	= ACTIVE_DISPLAY,
+	.load_mode	= 2,
+	.gfx_format	= GFXFORMAT_RGB16,
+};
+
+static const struct panel_config preset_dvi_1280X960 = {
+	.lcd_size	= PANEL_LCD_SIZE(1280, 960),
+	.timing_h	= DSS_HBP(312) | DSS_HFP(96) | DSS_HSW(112),
+	.timing_v	= DSS_VBP(36) | DSS_VFP(1) | DSS_VSW(3),
+	.divisor	= 3 | (1 << 16),
+	.data_lines	= LCD_INTERFACE_24_BIT,
+	.panel_type	= ACTIVE_DISPLAY,
+	.load_mode	= 2,
+	.gfx_format	= GFXFORMAT_RGB16,
+};
+
+static const struct panel_config preset_dvi_1280X1024 = {
+	.lcd_size	= PANEL_LCD_SIZE(1280, 1024),
+	.timing_h	= DSS_HBP(248) | DSS_HFP(48) | DSS_HSW(112),
+	.timing_v	= DSS_VBP(38) | DSS_VFP(1) | DSS_VSW(3),
+	.divisor	= 3 | (1 << 16),
+	.data_lines	= LCD_INTERFACE_24_BIT,
+	.panel_type	= ACTIVE_DISPLAY,
+	.load_mode	= 2,
+	.gfx_format	= GFXFORMAT_RGB16,
+};
+
+/*
+ * set_resolution_params()
+ *
+ * Due to usage of multiple display related APIs resolution data is located in
+ * more than one place. This function updates them all.
+ */
+static void set_resolution_params(int x, int y)
+{
+	panel_cfg.lcd_size = PANEL_LCD_SIZE(x, y);
+	panel_info.vl_col = x;
+	panel_info.vl_row = y;
+	lcd_line_length = (panel_info.vl_col * NBITS(panel_info.vl_bpix)) / 8;
+}
+
+static void set_preset(const struct panel_config preset, int x_res, int y_res)
+{
+	panel_cfg = preset;
+	set_resolution_params(x_res, y_res);
+}
+
+static enum display_type set_dvi_preset(const struct panel_config preset,
+					int x_res, int y_res)
+{
+	set_preset(preset, x_res, y_res);
+	return DVI;
+}
+
+/*
+ * parse_mode() - parse the mode parameter of custom lcd settings
+ *
+ * @mode:	<res_x>x<res_y>
+ *
+ * Returns -1 on error, 0 on success.
+ */
+static int parse_mode(const char *mode)
+{
+	unsigned int modelen = strlen(mode);
+	int res_specified = 0;
+	unsigned int xres = 0, yres = 0;
+	int yres_specified = 0;
+	int i;
+
+	for (i = modelen - 1; i >= 0; i--) {
+		switch (mode[i]) {
+		case 'x':
+			if (!yres_specified) {
+				yres = simple_strtoul(&mode[i + 1], NULL, 0);
+				yres_specified = 1;
+			} else {
+				goto done_parsing;
+			}
+
+			break;
+		case '0' ... '9':
+			break;
+		default:
+			goto done_parsing;
+		}
+	}
+
+	if (i < 0 && yres_specified) {
+		xres = simple_strtoul(mode, NULL, 0);
+		res_specified = 1;
+	}
+
+done_parsing:
+	if (res_specified) {
+		set_resolution_params(xres, yres);
+	} else {
+		printf("LCD: invalid mode: %s\n", mode);
+		return -1;
+	}
+
+	return 0;
+}
+
+#define PIXEL_CLK_NUMERATOR (26 * 432 / 39)
+/*
+ * parse_pixclock() - Parse the pixclock parameter of custom lcd settings
+ *
+ * @pixclock:	the desired pixel clock
+ *
+ * Returns -1 on error, 0 on success.
+ *
+ * Handling the pixel_clock:
+ *
+ * Pixel clock is defined in the OMAP35x TRM as follows:
+ * pixel_clock =
+ * (SYS_CLK * 2 * PRCM.CM_CLKSEL2_PLL[18:8]) /
+ * (DSS.DISPC_DIVISOR[23:16] * DSS.DISPC_DIVISOR[6:0] *
+ * PRCM.CM_CLKSEL_DSS[4:0] * (PRCM.CM_CLKSEL2_PLL[6:0] + 1))
+ *
+ * In practice, this means that in order to set the
+ * divisor for the desired pixel clock one needs to
+ * solve the following equation:
+ *
+ * 26 * 432 / (39 * <pixel_clock>) = DSS.DISPC_DIVISOR[6:0]
+ *
+ * NOTE: the explicit equation above is reduced. Do not
+ * try to infer anything from these numbers.
+ */
+static int parse_pixclock(char *pixclock)
+{
+	int divisor, pixclock_val;
+	char *pixclk_start = pixclock;
+
+	pixclock_val = simple_strtoul(pixclock, &pixclock, 10);
+	divisor = DIV_ROUND_UP(PIXEL_CLK_NUMERATOR, pixclock_val);
+	/* 0 and 1 are illegal values for PCD */
+	if (divisor <= 1)
+		divisor = 2;
+
+	panel_cfg.divisor = divisor | (1 << 16);
+	if (pixclock[0] != '\0') {
+		printf("LCD: invalid value for pixclock:%s\n", pixclk_start);
+		return -1;
+	}
+
+	return 0;
+}
+
+/*
+ * parse_setting() - parse a single setting of custom lcd parameters
+ *
+ * @setting:	The custom lcd setting <name>:<value>
+ *
+ * Returns -1 on failure, 0 on success.
+ */
+static int parse_setting(char *setting)
+{
+	int num_val;
+	char *setting_start = setting;
+
+	if (!strncmp(setting, "mode:", 5)) {
+		return parse_mode(setting + 5);
+	} else if (!strncmp(setting, "pixclock:", 9)) {
+		return parse_pixclock(setting + 9);
+	} else if (!strncmp(setting, "left:", 5)) {
+		num_val = simple_strtoul(setting + 5, &setting, 0);
+		panel_cfg.timing_h |= DSS_HBP(num_val);
+	} else if (!strncmp(setting, "right:", 6)) {
+		num_val = simple_strtoul(setting + 6, &setting, 0);
+		panel_cfg.timing_h |= DSS_HFP(num_val);
+	} else if (!strncmp(setting, "upper:", 6)) {
+		num_val = simple_strtoul(setting + 6, &setting, 0);
+		panel_cfg.timing_v |= DSS_VBP(num_val);
+	} else if (!strncmp(setting, "lower:", 6)) {
+		num_val = simple_strtoul(setting + 6, &setting, 0);
+		panel_cfg.timing_v |= DSS_VFP(num_val);
+	} else if (!strncmp(setting, "hsynclen:", 9)) {
+		num_val = simple_strtoul(setting + 9, &setting, 0);
+		panel_cfg.timing_h |= DSS_HSW(num_val);
+	} else if (!strncmp(setting, "vsynclen:", 9)) {
+		num_val = simple_strtoul(setting + 9, &setting, 0);
+		panel_cfg.timing_v |= DSS_VSW(num_val);
+	} else if (!strncmp(setting, "hsync:", 6)) {
+		if (simple_strtoul(setting + 6, &setting, 0) == 0)
+			panel_cfg.pol_freq |= DSS_IHS;
+		else
+			panel_cfg.pol_freq &= ~DSS_IHS;
+	} else if (!strncmp(setting, "vsync:", 6)) {
+		if (simple_strtoul(setting + 6, &setting, 0) == 0)
+			panel_cfg.pol_freq |= DSS_IVS;
+		else
+			panel_cfg.pol_freq &= ~DSS_IVS;
+	} else if (!strncmp(setting, "outputen:", 9)) {
+		if (simple_strtoul(setting + 9, &setting, 0) == 0)
+			panel_cfg.pol_freq |= DSS_IEO;
+		else
+			panel_cfg.pol_freq &= ~DSS_IEO;
+	} else if (!strncmp(setting, "pixclockpol:", 12)) {
+		if (simple_strtoul(setting + 12, &setting, 0) == 0)
+			panel_cfg.pol_freq |= DSS_IPC;
+		else
+			panel_cfg.pol_freq &= ~DSS_IPC;
+	} else if (!strncmp(setting, "active", 6)) {
+		panel_cfg.panel_type = ACTIVE_DISPLAY;
+		return 0; /* Avoid sanity check below */
+	} else if (!strncmp(setting, "passive", 7)) {
+		panel_cfg.panel_type = PASSIVE_DISPLAY;
+		return 0; /* Avoid sanity check below */
+	} else if (!strncmp(setting, "display:", 8)) {
+		if (!strncmp(setting + 8, "dvi", 3)) {
+			lcd_def = DVI_CUSTOM;
+			return 0; /* Avoid sanity check below */
+		}
+	} else {
+		printf("LCD: unknown option %s\n", setting_start);
+		return -1;
+	}
+
+	if (setting[0] != '\0') {
+		printf("LCD: invalid value for %s\n", setting_start);
+		return -1;
+	}
+
+	return 0;
+}
+
+/*
+ * env_parse_customlcd() - parse custom lcd params from an environment variable.
+ *
+ * @custom_lcd_params:	The environment variable containing the lcd params.
+ *
+ * Returns -1 on failure, 0 on success.
+ */
+static int parse_customlcd(char *custom_lcd_params)
+{
+	char params_cpy[160];
+	char *setting;
+
+	strncpy(params_cpy, custom_lcd_params, 160);
+	setting = strtok(params_cpy, ",");
+	while (setting) {
+		if (parse_setting(setting) < 0)
+			return -1;
+
+		setting = strtok(NULL, ",");
+	}
+
+	/* Currently we don't support changing this via custom lcd params */
+	panel_cfg.data_lines = LCD_INTERFACE_24_BIT;
+	panel_cfg.gfx_format = GFXFORMAT_RGB16; /* See dvi predefines note */
+
+	return 0;
+}
+
+/*
+ * env_parse_displaytype() - parse display type.
+ *
+ * Parses the environment variable "displaytype", which contains the
+ * name of the display type or preset, in which case it applies its
+ * configurations.
+ *
+ * Returns the type of display that was specified.
+ */
+static enum display_type env_parse_displaytype(char *displaytype)
+{
+	if (!strncmp(displaytype, "dvi640x480", 10))
+		return set_dvi_preset(preset_dvi_640X480, 640, 480);
+	else if (!strncmp(displaytype, "dvi800x600", 10))
+		return set_dvi_preset(preset_dvi_800X600, 800, 600);
+	else if (!strncmp(displaytype, "dvi1024x768", 11))
+		return set_dvi_preset(preset_dvi_1024X768, 1024, 768);
+	else if (!strncmp(displaytype, "dvi1152x864", 11))
+		return set_dvi_preset(preset_dvi_1152X864, 1152, 864);
+	else if (!strncmp(displaytype, "dvi1280x960", 11))
+		return set_dvi_preset(preset_dvi_1280X960, 1280, 960);
+	else if (!strncmp(displaytype, "dvi1280x1024", 12))
+		return set_dvi_preset(preset_dvi_1280X1024, 1280, 1024);
+
+	return NONE;
+}
+
+void lcd_ctrl_init(void *lcdbase)
+{
+	struct prcm *prcm = (struct prcm *)PRCM_BASE;
+	char *custom_lcd;
+	char *displaytype = getenv("displaytype");
+
+	if (displaytype == NULL)
+		return;
+
+	lcd_def = env_parse_displaytype(displaytype);
+	/* If we did not recognize the preset, check if it's an env variable */
+	if (lcd_def == NONE) {
+		custom_lcd = getenv(displaytype);
+		if (custom_lcd == NULL || parse_customlcd(custom_lcd) < 0)
+			return;
+	}
+
+	panel_cfg.frame_buffer = lcdbase;
+	omap3_dss_panel_config(&panel_cfg);
+	/*
+	 * Pixel clock is defined with many divisions and only few
+	 * multiplications of the system clock. Since DSS FCLK divisor is set
+	 * to 16 by default, we need to set it to a smaller value, like 3
+	 * (chosen via trial and error).
+	 */
+	clrsetbits_le32(&prcm->clksel_dss, 0xF, 3);
+}
+
+void lcd_enable(void)
+{
+	if (lcd_def == DVI || lcd_def == DVI_CUSTOM) {
+		gpio_direction_output(54, 0); /* Turn on DVI */
+		omap3_dss_enable();
+	}
+}
+
+void lcd_setcolreg(ushort regno, ushort red, ushort green, ushort blue) {}
diff --git a/board/compulab/cm_t35/eeprom.c b/board/compulab/cm_t35/eeprom.c
new file mode 100644
index 0000000000..b0af103cdd
--- /dev/null
+++ b/board/compulab/cm_t35/eeprom.c
@@ -0,0 +1,130 @@
+/*
+ * (C) Copyright 2011 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Authors: Nikita Kiryanov <nikita@compulab.co.il>
+ *	    Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#define EEPROM_LAYOUT_VER_OFFSET	44
+#define BOARD_SERIAL_OFFSET		20
+#define BOARD_SERIAL_OFFSET_LEGACY	8
+#define BOARD_REV_OFFSET		0
+#define BOARD_REV_OFFSET_LEGACY		6
+#define BOARD_REV_SIZE			2
+#define MAC_ADDR_OFFSET			4
+#define MAC_ADDR_OFFSET_LEGACY		0
+
+#define LAYOUT_INVALID	0
+#define LAYOUT_LEGACY	0xff
+
+static int eeprom_layout; /* Implicitly LAYOUT_INVALID */
+
+static int cm_t3x_eeprom_read(uint offset, uchar *buf, int len)
+{
+	return i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, offset,
+			CONFIG_SYS_I2C_EEPROM_ADDR_LEN, buf, len);
+}
+
+static int eeprom_setup_layout(void)
+{
+	int res;
+
+	if (eeprom_layout != LAYOUT_INVALID)
+		return 0;
+
+	res = cm_t3x_eeprom_read(EEPROM_LAYOUT_VER_OFFSET,
+						(uchar *)&eeprom_layout, 1);
+	if (res) {
+		eeprom_layout = LAYOUT_INVALID;
+		return res;
+	}
+
+	if (eeprom_layout == 0 || eeprom_layout >= 0x20)
+		eeprom_layout = LAYOUT_LEGACY;
+
+	return 0;
+}
+
+void get_board_serial(struct tag_serialnr *serialnr)
+{
+	u32 serial[2];
+	uint offset;
+
+	memset(serialnr, 0, sizeof(*serialnr));
+	if (eeprom_setup_layout())
+		return;
+
+	offset = (eeprom_layout != LAYOUT_LEGACY) ?
+			BOARD_SERIAL_OFFSET : BOARD_SERIAL_OFFSET_LEGACY;
+	if (cm_t3x_eeprom_read(offset, (uchar *)serial, 8))
+		return;
+
+	if (serial[0] != 0xffffffff && serial[1] != 0xffffffff) {
+		serialnr->low = serial[0];
+		serialnr->high = serial[1];
+	}
+}
+
+/*
+ * Routine: cm_t3x_eeprom_read_mac_addr
+ * Description: read mac address and store it in buf.
+ */
+int cm_t3x_eeprom_read_mac_addr(uchar *buf)
+{
+	uint offset;
+
+	if (eeprom_setup_layout())
+		return 0;
+
+	offset = (eeprom_layout != LAYOUT_LEGACY) ?
+			MAC_ADDR_OFFSET : MAC_ADDR_OFFSET_LEGACY;
+	return cm_t3x_eeprom_read(offset, buf, 6);
+}
+
+/*
+ * Routine: cm_t3x_eeprom_get_board_rev
+ * Description: read system revision from eeprom
+ */
+u32 cm_t3x_eeprom_get_board_rev(void)
+{
+	u32 rev = 0;
+	char str[5]; /* Legacy representation can contain at most 4 digits */
+	uint offset = BOARD_REV_OFFSET_LEGACY;
+
+	if (eeprom_setup_layout())
+		return 0;
+
+	if (eeprom_layout != LAYOUT_LEGACY)
+		offset = BOARD_REV_OFFSET;
+
+	if (cm_t3x_eeprom_read(offset, (uchar *)&rev, BOARD_REV_SIZE))
+		return 0;
+
+	/*
+	 * Convert legacy syntactic representation to semantic
+	 * representation. i.e. for rev 1.00: 0x100 --> 0x64
+	 */
+	if (eeprom_layout == LAYOUT_LEGACY) {
+		sprintf(str, "%x", rev);
+		rev = simple_strtoul(str, NULL, 10);
+	}
+
+	return rev;
+};
diff --git a/board/compulab/cm_t35/eeprom.h b/board/compulab/cm_t35/eeprom.h
new file mode 100644
index 0000000000..38824d162b
--- /dev/null
+++ b/board/compulab/cm_t35/eeprom.h
@@ -0,0 +1,38 @@
+/*
+ * (C) Copyright 2011 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Authors: Nikita Kiryanov <nikita@compulab.co.il>
+ *	    Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+#ifndef _EEPROM_
+#define _EEPROM_
+
+#ifdef CONFIG_DRIVER_OMAP34XX_I2C
+int cm_t3x_eeprom_read_mac_addr(uchar *buf);
+u32 cm_t3x_eeprom_get_board_rev(void);
+#else
+static inline int cm_t3x_eeprom_read_mac_addr(uchar *buf)
+{
+	return 1;
+}
+static inline u32 cm_t3x_eeprom_get_board_rev(void)
+{
+	return 0;
+}
+#endif
+
+#endif
diff --git a/board/compulab/cm_t35/leds.c b/board/compulab/cm_t35/leds.c
new file mode 100644
index 0000000000..dcae135c14
--- /dev/null
+++ b/board/compulab/cm_t35/leds.c
@@ -0,0 +1,44 @@
+/*
+ * (C) Copyright 2011 - 2013 CompuLab, Ltd. <www.compulab.co.il>
+ *
+ * Author: Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+#include <common.h>
+#include <status_led.h>
+#include <asm/gpio.h>
+
+static unsigned int leds[] = { GREEN_LED_GPIO };
+
+void __led_init(led_id_t mask, int state)
+{
+	if (gpio_request(leds[mask], "") != 0) {
+		printf("%s: failed requesting GPIO%u\n", __func__, leds[mask]);
+		return;
+	}
+
+	gpio_direction_output(leds[mask], 0);
+}
+
+void __led_set(led_id_t mask, int state)
+{
+	gpio_set_value(leds[mask], state == STATUS_LED_ON);
+}
+
+void __led_toggle(led_id_t mask)
+{
+	gpio_set_value(leds[mask], !gpio_get_value(leds[mask]));
+}
diff --git a/board/isee/igep0033/Makefile b/board/isee/igep0033/Makefile
new file mode 100644
index 0000000000..54a4b75252
--- /dev/null
+++ b/board/isee/igep0033/Makefile
@@ -0,0 +1,46 @@
+#
+# Makefile
+#
+# Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed "as is" WITHOUT ANY WARRANTY of any
+# kind, whether express or implied; without even the implied warranty
+# of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+ifdef CONFIG_SPL_BUILD
+COBJS	:= mux.o
+endif
+
+COBJS	+= board.o
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/isee/igep0033/board.c b/board/isee/igep0033/board.c
new file mode 100644
index 0000000000..d315516fea
--- /dev/null
+++ b/board/isee/igep0033/board.c
@@ -0,0 +1,232 @@
+/*
+ * Board functions for IGEP COM AQUILA/CYGNUS based boards
+ *
+ * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
+#ifdef CONFIG_SPL_BUILD
+static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
+#endif
+
+/* MII mode defines */
+#define RMII_MODE_ENABLE	0x4D
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+/* UART Defines */
+#ifdef CONFIG_SPL_BUILD
+#define UART_RESET		(0x1 << 1)
+#define UART_CLK_RUNNING_MASK	0x1
+#define UART_SMART_IDLE_EN	(0x1 << 0x3)
+
+static void rtc32k_enable(void)
+{
+	struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE;
+
+	/*
+	 * Unlock the RTC's registers.  For more details please see the
+	 * RTC_SS section of the TRM.  In order to unlock we need to
+	 * write these specific values (keys) in this order.
+	 */
+	writel(0x83e70b13, &rtc->kick0r);
+	writel(0x95a4f1e0, &rtc->kick1r);
+
+	/* Enable the RTC 32K OSC by setting bits 3 and 6. */
+	writel((1 << 3) | (1 << 6), &rtc->osc);
+}
+
+static const struct ddr_data ddr3_data = {
+	.datardsratio0 = K4B2G1646EBIH9_RD_DQS,
+	.datawdsratio0 = K4B2G1646EBIH9_WR_DQS,
+	.datafwsratio0 = K4B2G1646EBIH9_PHY_FIFO_WE,
+	.datawrsratio0 = K4B2G1646EBIH9_PHY_WR_DATA,
+	.datadldiff0 = PHY_DLL_LOCK_DIFF,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+	.cmd0csratio = K4B2G1646EBIH9_RATIO,
+	.cmd0dldiff = K4B2G1646EBIH9_DLL_LOCK_DIFF,
+	.cmd0iclkout = K4B2G1646EBIH9_INVERT_CLKOUT,
+
+	.cmd1csratio = K4B2G1646EBIH9_RATIO,
+	.cmd1dldiff = K4B2G1646EBIH9_DLL_LOCK_DIFF,
+	.cmd1iclkout = K4B2G1646EBIH9_INVERT_CLKOUT,
+
+	.cmd2csratio = K4B2G1646EBIH9_RATIO,
+	.cmd2dldiff = K4B2G1646EBIH9_DLL_LOCK_DIFF,
+	.cmd2iclkout = K4B2G1646EBIH9_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+	.sdram_config = K4B2G1646EBIH9_EMIF_SDCFG,
+	.ref_ctrl = K4B2G1646EBIH9_EMIF_SDREF,
+	.sdram_tim1 = K4B2G1646EBIH9_EMIF_TIM1,
+	.sdram_tim2 = K4B2G1646EBIH9_EMIF_TIM2,
+	.sdram_tim3 = K4B2G1646EBIH9_EMIF_TIM3,
+	.zq_config = K4B2G1646EBIH9_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = K4B2G1646EBIH9_EMIF_READ_LATENCY,
+};
+#endif
+
+/*
+ * Early system init of muxing and clocks.
+ */
+void s_init(void)
+{
+	/* WDT1 is already running when the bootloader gets control
+	 * Disable it to avoid "random" resets
+	 */
+	writel(0xAAAA, &wdtimer->wdtwspr);
+	while (readl(&wdtimer->wdtwwps) != 0x0)
+		;
+	writel(0x5555, &wdtimer->wdtwspr);
+	while (readl(&wdtimer->wdtwwps) != 0x0)
+		;
+
+#ifdef CONFIG_SPL_BUILD
+	/* Setup the PLLs and the clocks for the peripherals */
+	pll_init();
+
+	/* Enable RTC32K clock */
+	rtc32k_enable();
+
+	/* UART softreset */
+	u32 regval;
+
+	enable_uart0_pin_mux();
+
+	regval = readl(&uart_base->uartsyscfg);
+	regval |= UART_RESET;
+	writel(regval, &uart_base->uartsyscfg);
+	while ((readl(&uart_base->uartsyssts) &
+		UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK)
+		;
+
+	/* Disable smart idle */
+	regval = readl(&uart_base->uartsyscfg);
+	regval |= UART_SMART_IDLE_EN;
+	writel(regval, &uart_base->uartsyscfg);
+
+	gd = &gdata;
+
+	preloader_console_init();
+
+	/* Configure board pin mux */
+	enable_board_pin_mux();
+
+	config_ddr(303, K4B2G1646EBIH9_IOCTRL_VALUE, &ddr3_data,
+		   &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
+#endif
+}
+
+/*
+ * Basic board specific setup.  Pinmux has been handled already.
+ */
+int board_init(void)
+{
+	gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+
+	gpmc_init();
+
+	return 0;
+}
+
+#if defined(CONFIG_DRIVER_TI_CPSW)
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_id		= 0,
+		.phy_if		= PHY_INTERFACE_MODE_RMII,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+
+int board_eth_init(bd_t *bis)
+{
+	int rv, ret = 0;
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+		/* try reading mac address from efuse */
+		mac_lo = readl(&cdev->macid0l);
+		mac_hi = readl(&cdev->macid0h);
+		mac_addr[0] = mac_hi & 0xFF;
+		mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+		mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+		mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+		mac_addr[4] = mac_lo & 0xFF;
+		mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+	}
+
+	writel(RMII_MODE_ENABLE, &cdev->miisel);
+
+	rv = cpsw_register(&cpsw_data);
+	if (rv < 0)
+		printf("Error %d registering CPSW switch\n", rv);
+	else
+		ret += rv;
+
+	return ret;
+}
+#endif
+
diff --git a/board/isee/igep0033/board.h b/board/isee/igep0033/board.h
new file mode 100644
index 0000000000..37988e0fd3
--- /dev/null
+++ b/board/isee/igep0033/board.h
@@ -0,0 +1,27 @@
+/*
+ * IGEP COM AQUILA/CYGNUS boards information header
+ *
+ * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * We must be able to enable uart0, for initial output. We then have a
+ * main pinmux function that can be overridden to enable all other pinmux that
+ * is required on the board.
+ */
+void enable_uart0_pin_mux(void);
+void enable_board_pin_mux(void);
+#endif
diff --git a/board/isee/igep0033/mux.c b/board/isee/igep0033/mux.c
new file mode 100644
index 0000000000..16f4addf3d
--- /dev/null
+++ b/board/isee/igep0033/mux.c
@@ -0,0 +1,89 @@
+/*
+ * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include "board.h"
+
+static struct module_pin_mux uart0_pin_mux[] = {
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* UART0_RXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},		/* UART0_TXD */
+	{-1},
+};
+
+static struct module_pin_mux mmc0_pin_mux[] = {
+	{OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT3 */
+	{OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT2 */
+	{OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT1 */
+	{OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT0 */
+	{OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_CLK */
+	{OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_CMD */
+	{OFFSET(mcasp0_aclkx), (MODE(4) | RXACTIVE)},		/* MMC0_CD */
+	{-1},
+};
+
+static struct module_pin_mux nand_pin_mux[] = {
+	{OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD0 */
+	{OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD1 */
+	{OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD2 */
+	{OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD3 */
+	{OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD4 */
+	{OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD5 */
+	{OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD6 */
+	{OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD7 */
+	{OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+	{OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)},	/* NAND_WPN */
+	{OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)},		/* NAND_CS0 */
+	{OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)},	/* NAND_ADV_ALE */
+	{OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)},	/* NAND_OE */
+	{OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)},	/* NAND_WEN */
+	{OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)},	/* NAND_BE_CLE */
+	{-1},
+};
+
+static struct module_pin_mux rmii1_pin_mux[] = {
+	{OFFSET(mii1_txen), MODE(1)},			/* RMII1_TXEN */
+	{OFFSET(mii1_rxerr), MODE(1) | RXACTIVE},	/* RMII1_RXERR */
+	{OFFSET(mii1_crs), MODE(1) | RXACTIVE},		/* RMII1_CRS_DV */
+	{OFFSET(mii1_rxd0), MODE(1) | RXACTIVE},	/* RMII1_RXD0 */
+	{OFFSET(mii1_rxd1), MODE(1) | RXACTIVE},	/* RMII1_RXD1 */
+	{OFFSET(mii1_txd0), MODE(1)},			/* RMII1_TXD0 */
+	{OFFSET(mii1_txd1), MODE(1)},			/* RMII1_TXD1 */
+	{OFFSET(rmii1_refclk), MODE(0) | RXACTIVE},	/* RMII1_REF_CLK */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},	/* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+/*
+ * Do board-specific muxes.
+ */
+void enable_board_pin_mux(void)
+{
+	/* NAND Flash */
+	configure_module_pin_mux(nand_pin_mux);
+	/* SD Card */
+	configure_module_pin_mux(mmc0_pin_mux);
+	/* Ethernet pinmux. */
+	configure_module_pin_mux(rmii1_pin_mux);
+}
+
diff --git a/board/nokia/rx51/rx51.c b/board/nokia/rx51/rx51.c
index 48eb65f896..42bf8b669d 100644
--- a/board/nokia/rx51/rx51.c
+++ b/board/nokia/rx51/rx51.c
@@ -332,10 +332,10 @@ void *video_hw_init(void)
 static void twl4030_regulator_set_mode(u8 id, u8 mode)
 {
 	u16 msg = MSG_SINGULAR(DEV_GRP_P1, id, mode);
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, msg >> 8,
-			TWL4030_PM_MASTER_PB_WORD_MSB);
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, msg & 0xff,
-			TWL4030_PM_MASTER_PB_WORD_LSB);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+			     TWL4030_PM_MASTER_PB_WORD_MSB, msg >> 8);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+			     TWL4030_PM_MASTER_PB_WORD_LSB, msg & 0xff);
 }
 
 static void omap3_emu_romcode_call(u32 service_id, u32 *parameters)
@@ -406,12 +406,12 @@ int misc_init_r(void)
 				TWL4030_PM_RECEIVER_DEV_GRP_P1);
 
 	/* store I2C access state */
-	twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER, &state,
-			TWL4030_PM_MASTER_PB_CFG);
+	twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG,
+			    &state);
 
 	/* enable I2C access to powerbus (needed for twl4030 regulator) */
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x02,
-			TWL4030_PM_MASTER_PB_CFG);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG,
+			     0x02);
 
 	/* set VAUX3, VSIM and VMMC1 state to active - enable eMMC memory */
 	twl4030_regulator_set_mode(RES_VAUX3, RES_STATE_ACTIVE);
@@ -419,8 +419,8 @@ int misc_init_r(void)
 	twl4030_regulator_set_mode(RES_VMMC1, RES_STATE_ACTIVE);
 
 	/* restore I2C access state */
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, state,
-			TWL4030_PM_MASTER_PB_CFG);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG,
+			     state);
 
 	/* set env variable attkernaddr for relocated kernel */
 	sprintf(buf, "%#x", KERNEL_ADDRESS);
@@ -475,14 +475,14 @@ void hw_watchdog_reset(void)
 		return;
 
 	/* read actual watchdog timeout */
-	twl4030_i2c_read_u8(TWL4030_CHIP_PM_RECEIVER, &timeout,
-			TWL4030_PM_RECEIVER_WATCHDOG_CFG);
+	twl4030_i2c_read_u8(TWL4030_CHIP_PM_RECEIVER,
+			    TWL4030_PM_RECEIVER_WATCHDOG_CFG, &timeout);
 
 	/* timeout 0 means watchdog is disabled */
 	/* reset watchdog timeout to 31s (maximum) */
 	if (timeout != 0)
-		twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 31,
-				TWL4030_PM_RECEIVER_WATCHDOG_CFG);
+		twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+				     TWL4030_PM_RECEIVER_WATCHDOG_CFG, 31);
 
 	/* store last watchdog reset time */
 	twl_wd_time = get_timer(0);
@@ -531,8 +531,8 @@ int rx51_kp_init(void)
 {
 	int ret = 0;
 	u8 ctrl;
-	ret = twl4030_i2c_read_u8(TWL4030_CHIP_KEYPAD, &ctrl,
-		TWL4030_KEYPAD_KEYP_CTRL_REG);
+	ret = twl4030_i2c_read_u8(TWL4030_CHIP_KEYPAD,
+				  TWL4030_KEYPAD_KEYP_CTRL_REG, &ctrl);
 
 	if (ret)
 		return ret;
@@ -541,18 +541,18 @@ int rx51_kp_init(void)
 	ctrl |= TWL4030_KEYPAD_CTRL_KBD_ON;
 	ctrl |= TWL4030_KEYPAD_CTRL_SOFT_NRST;
 	ctrl |= TWL4030_KEYPAD_CTRL_SOFTMODEN;
-	ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, ctrl,
-				TWL4030_KEYPAD_KEYP_CTRL_REG);
+	ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD,
+				    TWL4030_KEYPAD_KEYP_CTRL_REG, ctrl);
 	/* enable key event status */
-	ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0xfe,
-				TWL4030_KEYPAD_KEYP_IMR1);
+	ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD,
+				    TWL4030_KEYPAD_KEYP_IMR1, 0xfe);
 	/* enable interrupt generation on rising and falling */
 	/* this is a workaround for qemu twl4030 emulation */
-	ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0x57,
-				TWL4030_KEYPAD_KEYP_EDR);
+	ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD,
+				    TWL4030_KEYPAD_KEYP_EDR, 0x57);
 	/* enable ISR clear on read */
-	ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0x05,
-				TWL4030_KEYPAD_KEYP_SIH_CTRL);
+	ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD,
+				    TWL4030_KEYPAD_KEYP_SIH_CTRL, 0x05);
 	return 0;
 }
 
@@ -615,8 +615,8 @@ int rx51_kp_tstc(void)
 	for (i = 0; i < 2; i++) {
 
 		/* check interrupt register for events */
-		twl4030_i2c_read_u8(TWL4030_CHIP_KEYPAD, &intr,
-				TWL4030_KEYPAD_KEYP_ISR1+(2*i));
+		twl4030_i2c_read_u8(TWL4030_CHIP_KEYPAD,
+				    TWL4030_KEYPAD_KEYP_ISR1 + (2 * i), &intr);
 
 		/* no event */
 		if (!(intr&1))
diff --git a/board/pandora/pandora.c b/board/pandora/pandora.c
index 9ff5dd7664..5f0c58d8d2 100644
--- a/board/pandora/pandora.c
+++ b/board/pandora/pandora.c
@@ -114,8 +114,9 @@ int misc_init_r(void)
 
 	/* Enable battery backup capacitor (3.2V, 0.5mA charge current) */
 	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+		TWL4030_PM_RECEIVER_BB_CFG,
 		TWL4030_BB_CFG_BBCHEN | TWL4030_BB_CFG_BBSEL_3200MV |
-		TWL4030_BB_CFG_BBISEL_500UA, TWL4030_PM_RECEIVER_BB_CFG);
+		TWL4030_BB_CFG_BBISEL_500UA);
 
 	dieid_num_r();
 
diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
index 3d9b6dd8fd..c686f40a93 100644
--- a/board/ti/beagle/beagle.c
+++ b/board/ti/beagle/beagle.c
@@ -108,13 +108,14 @@ int board_init(void)
 /*
  * Routine: get_board_revision
  * Description: Detect if we are running on a Beagle revision Ax/Bx,
- *		C1/2/3, C4 or xM. This can be done by reading
+ *		C1/2/3, C4, xM Ax/Bx or xM Cx. This can be done by reading
  *		the level of GPIO173, GPIO172 and GPIO171. This should
  *		result in
  *		GPIO173, GPIO172, GPIO171: 1 1 1 => Ax/Bx
  *		GPIO173, GPIO172, GPIO171: 1 1 0 => C1/2/3
  *		GPIO173, GPIO172, GPIO171: 1 0 1 => C4
- *		GPIO173, GPIO172, GPIO171: 0 0 0 => xM
+ *		GPIO173, GPIO172, GPIO171: 0 1 0 => xM Cx
+ *		GPIO173, GPIO172, GPIO171: 0 0 0 => xM Ax/Bx
  */
 static int get_board_revision(void)
 {
diff --git a/board/ti/dra7xx/evm.c b/board/ti/dra7xx/evm.c
index 7bbb5492fe..bf7e091966 100644
--- a/board/ti/dra7xx/evm.c
+++ b/board/ti/dra7xx/evm.c
@@ -27,7 +27,7 @@
  * MA 02111-1307 USA
  */
 #include <common.h>
-#include <twl6035.h>
+#include <palmas.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/arch/mmc_host_def.h>
 
diff --git a/board/ti/omap5_uevm/evm.c b/board/ti/omap5_uevm/evm.c
index 55337c09d5..46db1bfe66 100644
--- a/board/ti/omap5_uevm/evm.c
+++ b/board/ti/omap5_uevm/evm.c
@@ -23,7 +23,7 @@
  * MA 02111-1307 USA
  */
 #include <common.h>
-#include <twl6035.h>
+#include <palmas.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/arch/mmc_host_def.h>
 
@@ -63,8 +63,8 @@ int board_eth_init(bd_t *bis)
  */
 int misc_init_r(void)
 {
-#ifdef CONFIG_TWL6035_POWER
-	twl6035_init_settings();
+#ifdef CONFIG_PALMAS_POWER
+	palmas_init_settings();
 #endif
 	return 0;
 }
diff --git a/board/ti/panda/panda.c b/board/ti/panda/panda.c
index cab059863d..2bbe392d81 100644
--- a/board/ti/panda/panda.c
+++ b/board/ti/panda/panda.c
@@ -82,6 +82,12 @@ int misc_init_r(void)
 	if (omap_revision() == OMAP4430_ES1_0)
 		return 0;
 
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	if (omap_revision() >= OMAP4460_ES1_0 ||
+		omap_revision() <= OMAP4460_ES1_1)
+		setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es"));
+#endif
+
 	gpio_direction_input(PANDA_ULPI_PHY_TYPE_GPIO);
 	phy_type = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
 
diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c
index 446e36b844..7adb52405c 100644
--- a/board/ti/ti814x/evm.c
+++ b/board/ti/ti814x/evm.c
@@ -17,6 +17,7 @@
  */
 
 #include <common.h>
+#include <cpsw.h>
 #include <errno.h>
 #include <spl.h>
 #include <asm/arch/cpu.h>
@@ -39,6 +40,8 @@ static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
 static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
 #endif
 
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
 /* UART Defines */
 #ifdef CONFIG_SPL_BUILD
 #define UART_RESET		(0x1 << 1)
@@ -151,6 +154,9 @@ void s_init(void)
 	 */
 	wdt_disable();
 
+	/* Enable timer */
+	timer_init();
+
 	/* Setup the PLLs and the clocks for the peripherals */
 	pll_init();
 
@@ -163,6 +169,9 @@ void s_init(void)
 	/* Set MMC pins */
 	enable_mmc1_pin_mux();
 
+	/* Set Ethernet pins */
+	enable_enet_pin_mux();
+
 	/* Enable UART */
 	uart_enable();
 
@@ -196,3 +205,69 @@ int board_mmc_init(bd_t *bis)
 	return 0;
 }
 #endif
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x50,
+		.sliver_reg_ofs	= 0x700,
+		.phy_id		= 1,
+	},
+	{
+		.slave_reg_ofs	= 0x90,
+		.sliver_reg_ofs	= 0x740,
+		.phy_id		= 0,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x100,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0x600,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x28,
+	.hw_stats_reg_ofs	= 0x400,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_1,
+};
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+		printf("<ethaddr> not set. Reading from E-fuse\n");
+		/* try reading mac address from efuse */
+		mac_lo = readl(&cdev->macid0l);
+		mac_hi = readl(&cdev->macid0h);
+		mac_addr[0] = mac_hi & 0xFF;
+		mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+		mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+		mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+		mac_addr[4] = mac_lo & 0xFF;
+		mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+		else
+			printf("Unable to read MAC address. Set <ethaddr>\n");
+	}
+
+	return cpsw_register(&cpsw_data);
+}
diff --git a/board/ti/ti814x/evm.h b/board/ti/ti814x/evm.h
index 40f8710c89..6aebec62d4 100644
--- a/board/ti/ti814x/evm.h
+++ b/board/ti/ti814x/evm.h
@@ -3,5 +3,6 @@
 
 void enable_uart0_pin_mux(void);
 void enable_mmc1_pin_mux(void);
+void enable_enet_pin_mux(void);
 
 #endif /* _EVM_H */
diff --git a/board/ti/ti814x/mux.c b/board/ti/ti814x/mux.c
index 137acb4523..fd9f364511 100644
--- a/board/ti/ti814x/mux.c
+++ b/board/ti/ti814x/mux.c
@@ -40,6 +40,36 @@ static struct module_pin_mux mmc1_pin_mux[] = {
 	{-1},
 };
 
+static struct module_pin_mux enet_pin_mux[] = {
+	{OFFSET(pincntl232), MODE(0x01)},		/* EMAC_RMREFCLK */
+	{OFFSET(pincntl233), PULLUP_EN | MODE(0x01)},	/* MDCLK */
+	{OFFSET(pincntl234), PULLUP_EN | MODE(0x01)},	/* MDIO */
+	{OFFSET(pincntl235), MODE(0x01)},		/* EMAC[0]_MTCLK */
+	{OFFSET(pincntl236), MODE(0x01)},		/* EMAC[0]_MCOL */
+	{OFFSET(pincntl237), MODE(0x01)},		/* EMAC[0]_MCRS */
+	{OFFSET(pincntl238), MODE(0x01)},		/* EMAC[0]_MRXER */
+	{OFFSET(pincntl239), MODE(0x01)},		/* EMAC[0]_MRCLK */
+	{OFFSET(pincntl240), MODE(0x01)},		/* EMAC[0]_MRXD[0] */
+	{OFFSET(pincntl241), MODE(0x01)},		/* EMAC[0]_MRXD[1] */
+	{OFFSET(pincntl242), MODE(0x01)},		/* EMAC[0]_MRXD[2] */
+	{OFFSET(pincntl243), MODE(0x01)},		/* EMAC[0]_MRXD[3] */
+	{OFFSET(pincntl244), MODE(0x01)},		/* EMAC[0]_MRXD[4] */
+	{OFFSET(pincntl245), MODE(0x01)},		/* EMAC[0]_MRXD[5] */
+	{OFFSET(pincntl246), MODE(0x01)},		/* EMAC[0]_MRXD[6] */
+	{OFFSET(pincntl247), MODE(0x01)},		/* EMAC[0]_MRXD[7] */
+	{OFFSET(pincntl248), MODE(0x01)},		/* EMAC[0]_MRXDV */
+	{OFFSET(pincntl249), MODE(0x01)},		/* EMAC[0]_GMTCLK */
+	{OFFSET(pincntl250), MODE(0x01)},		/* EMAC[0]_MTXD[0] */
+	{OFFSET(pincntl251), MODE(0x01)},		/* EMAC[0]_MTXD[1] */
+	{OFFSET(pincntl252), MODE(0x01)},		/* EMAC[0]_MTXD[2] */
+	{OFFSET(pincntl253), MODE(0x01)},		/* EMAC[0]_MTXD[3] */
+	{OFFSET(pincntl254), MODE(0x01)},		/* EMAC[0]_MTXD[4] */
+	{OFFSET(pincntl255), MODE(0x01)},		/* EMAC[0]_MTXD[5] */
+	{OFFSET(pincntl256), MODE(0x01)},		/* EMAC[0]_MTXD[6] */
+	{OFFSET(pincntl257), MODE(0x01)},		/* EMAC[0]_MTXD[7] */
+	{OFFSET(pincntl258), MODE(0x01)},		/* EMAC[0]_MTXEN */
+};
+
 void enable_uart0_pin_mux(void)
 {
 	configure_module_pin_mux(uart0_pin_mux);
@@ -49,3 +79,8 @@ void enable_mmc1_pin_mux(void)
 {
 	configure_module_pin_mux(mmc1_pin_mux);
 }
+
+void enable_enet_pin_mux(void)
+{
+	configure_module_pin_mux(enet_pin_mux);
+}
diff --git a/boards.cfg b/boards.cfg
index 0e082a072c..2f39f26833 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -271,15 +271,16 @@ nitrogen6s                   arm         armv7       nitrogen6x          boundar
 nitrogen6s1g                 arm         armv7       nitrogen6x          boundary       mx6		nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s1g.cfg,MX6S,DDR_MB=1024
 wandboard_dl		     arm	 armv7	     wandboard		 -		mx6 wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DDR_MB=1024
 wandboard_solo		     arm	 armv7	     wandboard		 -		mx6 wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512
-cm_t35                       arm         armv7       cm_t35              -              omap3
 omap3_overo                  arm         armv7       overo               -              omap3
 omap3_pandora                arm         armv7       pandora             -              omap3
 dig297                       arm         armv7       dig297              comelit        omap3
+cm_t35                       arm         armv7       cm_t35              compulab       omap3
 igep0020                     arm         armv7       igep00x0            isee           omap3		igep00x0:MACH_TYPE=MACH_TYPE_IGEP0020,BOOT_ONENAND
 igep0020_nand                arm         armv7       igep00x0            isee           omap3		igep00x0:MACH_TYPE=MACH_TYPE_IGEP0020,BOOT_NAND
 igep0030                     arm         armv7       igep00x0            isee           omap3		igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_ONENAND
 igep0030_nand                arm         armv7       igep00x0            isee           omap3		igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_NAND
 igep0032                     arm         armv7       igep00x0            isee           omap3		igep00x0:MACH_TYPE=MACH_TYPE_IGEP0032,BOOT_ONENAND
+igep0033                     arm         armv7       igep0033            isee           am33xx
 am3517_evm                   arm         armv7       am3517evm           logicpd        omap3
 mt_ventoux                   arm         armv7       mt_ventoux          teejet         omap3
 omap3_zoom1                  arm         armv7       zoom1               logicpd        omap3
diff --git a/common/spl/spl.c b/common/spl/spl.c
index 7ce2d5f214..628c3990ff 100644
--- a/common/spl/spl.c
+++ b/common/spl/spl.c
@@ -118,17 +118,13 @@ void spl_parse_image_header(const struct image_header *header)
 
 __weak void __noreturn jump_to_image_no_args(struct spl_image_info *spl_image)
 {
-	typedef void __noreturn (*image_entry_noargs_t)(u32 *);
+	typedef void __noreturn (*image_entry_noargs_t)(void);
+
 	image_entry_noargs_t image_entry =
 			(image_entry_noargs_t) spl_image->entry_point;
 
 	debug("image entry point: 0x%X\n", spl_image->entry_point);
-	/* Pass the saved boot_params from rom code */
-#if defined(CONFIG_VIRTIO) || defined(CONFIG_ZEBU)
-	image_entry = (image_entry_noargs_t)0x80100000;
-#endif
-	u32 boot_params_ptr_addr = (u32)&boot_params_ptr;
-	image_entry((u32 *)boot_params_ptr_addr);
+	image_entry();
 }
 
 #ifdef CONFIG_SPL_RAM_DEVICE
diff --git a/doc/README.omap-reset-time b/doc/README.omap-reset-time
new file mode 100644
index 0000000000..0c974bacae
--- /dev/null
+++ b/doc/README.omap-reset-time
@@ -0,0 +1,20 @@
+README on how reset time on OMAPs should be calculated
+
+CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC:
+Most OMAPs' provide a way to specify the time for
+which the reset should be held low while the voltages
+and Oscillator outputs stabilize.
+
+This time is mostly board and PMIC dependent. Hence the
+boards are expected to specify a pre-computed time
+using the above option, (the details on how to compute
+the value are given below) without which a default time
+as specified by CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC
+is used.
+
+The value for CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC
+can be computed using a summation of the below 3 parameters
+-1- Time taken by the Osciallator to stop and restart
+-2- PMIC OTP time
+-3- Voltage ramp time, which can be derived using the
+PMIC slew rate and value of voltage ramp needed.
diff --git a/drivers/misc/twl4030_led.c b/drivers/misc/twl4030_led.c
index 33cea116d2..e150d8f037 100644
--- a/drivers/misc/twl4030_led.c
+++ b/drivers/misc/twl4030_led.c
@@ -42,7 +42,7 @@ void twl4030_led_init(unsigned char ledon_mask)
 	if (ledon_mask & TWL4030_LED_LEDEN_LEDBON)
 		ledon_mask |= TWL4030_LED_LEDEN_LEDBPWM;
 
-	twl4030_i2c_write_u8(TWL4030_CHIP_LED, ledon_mask,
-			     TWL4030_LED_LEDEN);
+	twl4030_i2c_write_u8(TWL4030_CHIP_LED, TWL4030_LED_LEDEN,
+			     ledon_mask);
 
 }
diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c
index 166744c320..afdfa886e8 100644
--- a/drivers/mmc/omap_hsmmc.c
+++ b/drivers/mmc/omap_hsmmc.c
@@ -29,7 +29,7 @@
 #include <i2c.h>
 #include <twl4030.h>
 #include <twl6030.h>
-#include <twl6035.h>
+#include <palmas.h>
 #include <asm/gpio.h>
 #include <asm/io.h>
 #include <asm/arch/mmc_host_def.h>
@@ -107,7 +107,7 @@ static void omap4_vmmc_pbias_config(struct mmc *mmc)
 }
 #endif
 
-#if defined(CONFIG_OMAP54XX) && defined(CONFIG_TWL6035_POWER)
+#if defined(CONFIG_OMAP54XX) && defined(CONFIG_PALMAS_POWER)
 static void omap5_pbias_config(struct mmc *mmc)
 {
 	u32 value = 0;
@@ -117,7 +117,7 @@ static void omap5_pbias_config(struct mmc *mmc)
 	value |= SDCARD_BIAS_HIZ_MODE;
 	writel(value, (*ctrl)->control_pbias);
 
-	twl6035_mmc1_poweron_ldo();
+	palmas_mmc1_poweron_ldo();
 
 	value = readl((*ctrl)->control_pbias);
 	value &= ~SDCARD_BIAS_HIZ_MODE;
@@ -178,7 +178,7 @@ unsigned char mmc_board_init(struct mmc *mmc)
 	if (mmc->block_dev.dev == 0)
 		omap4_vmmc_pbias_config(mmc);
 #endif
-#if defined(CONFIG_OMAP54XX) && defined(CONFIG_TWL6035_POWER)
+#if defined(CONFIG_OMAP54XX) && defined(CONFIG_PALMAS_POWER)
 	if (mmc->block_dev.dev == 0)
 		omap5_pbias_config(mmc);
 #endif
diff --git a/drivers/net/cpsw.c b/drivers/net/cpsw.c
index 7a36850198..379b679d2e 100644
--- a/drivers/net/cpsw.c
+++ b/drivers/net/cpsw.c
@@ -109,7 +109,13 @@ struct cpsw_slave_regs {
 	u32	flow_thresh;
 	u32	port_vlan;
 	u32	tx_pri_map;
+#ifdef CONFIG_AM33XX
 	u32	gap_thresh;
+#elif defined(CONFIG_TI814X)
+	u32	ts_ctl;
+	u32	ts_seq_ltype;
+	u32	ts_vlan;
+#endif
 	u32	sa_lo;
 	u32	sa_hi;
 };
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 5e90d7098d..af5f4b848c 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -34,6 +34,7 @@ COBJS-$(CONFIG_PHYLIB_10G) += generic_10g.o
 COBJS-$(CONFIG_PHY_ATHEROS) += atheros.o
 COBJS-$(CONFIG_PHY_BROADCOM) += broadcom.o
 COBJS-$(CONFIG_PHY_DAVICOM) += davicom.o
+COBJS-$(CONFIG_PHY_ET1011C) += et1011c.o
 COBJS-$(CONFIG_PHY_LXT) += lxt.o
 COBJS-$(CONFIG_PHY_MARVELL) += marvell.o
 COBJS-$(CONFIG_PHY_MICREL) += micrel.o
diff --git a/drivers/net/phy/et1011c.c b/drivers/net/phy/et1011c.c
new file mode 100644
index 0000000000..5e22399af1
--- /dev/null
+++ b/drivers/net/phy/et1011c.c
@@ -0,0 +1,110 @@
+/*
+ * ET1011C PHY driver
+ *
+ * Derived from Linux kernel driver by Chaithrika U S
+ * Copyright (C) 2013, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+#include <config.h>
+#include <phy.h>
+
+#define ET1011C_CONFIG_REG		(0x16)
+#define ET1011C_TX_FIFO_MASK		(0x3 << 12)
+#define ET1011C_TX_FIFO_DEPTH_8		(0x0 << 12)
+#define ET1011C_TX_FIFO_DEPTH_16	(0x1 << 12)
+#define ET1011C_INTERFACE_MASK		(0x7 << 0)
+#define ET1011C_GMII_INTERFACE		(0x2 << 0)
+#define ET1011C_SYS_CLK_EN		(0x1 << 4)
+#define ET1011C_TX_CLK_EN		(0x1 << 5)
+
+#define ET1011C_STATUS_REG		(0x1A)
+#define ET1011C_DUPLEX_STATUS		(0x1 << 7)
+#define ET1011C_SPEED_MASK		(0x3 << 8)
+#define ET1011C_SPEED_1000		(0x2 << 8)
+#define ET1011C_SPEED_100		(0x1 << 8)
+#define ET1011C_SPEED_10		(0x0 << 8)
+
+static int et1011c_config(struct phy_device *phydev)
+{
+	int ctl = 0;
+	ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+	if (ctl < 0)
+		return ctl;
+	ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 |
+		 BMCR_ANENABLE);
+	/* First clear the PHY */
+	phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, ctl | BMCR_RESET);
+
+	return genphy_config_aneg(phydev);
+}
+
+static int et1011c_parse_status(struct phy_device *phydev)
+{
+	int mii_reg;
+	int speed;
+
+	mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, ET1011C_STATUS_REG);
+
+	if (mii_reg & ET1011C_DUPLEX_STATUS)
+		phydev->duplex = DUPLEX_FULL;
+	else
+		phydev->duplex = DUPLEX_HALF;
+
+	speed = mii_reg & ET1011C_SPEED_MASK;
+	switch (speed) {
+	case ET1011C_SPEED_1000:
+		phydev->speed = SPEED_1000;
+		mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, ET1011C_CONFIG_REG);
+		mii_reg &= ~ET1011C_TX_FIFO_MASK;
+		phy_write(phydev, MDIO_DEVAD_NONE, ET1011C_CONFIG_REG,
+			  mii_reg |
+			  ET1011C_GMII_INTERFACE |
+			  ET1011C_SYS_CLK_EN |
+#ifdef CONFIG_PHY_ET1011C_TX_CLK_FIX
+			  ET1011C_TX_CLK_EN |
+#endif
+			  ET1011C_TX_FIFO_DEPTH_16);
+		break;
+	case ET1011C_SPEED_100:
+		phydev->speed = SPEED_100;
+		break;
+	case ET1011C_SPEED_10:
+		phydev->speed = SPEED_10;
+		break;
+	}
+
+	return 0;
+}
+
+static int et1011c_startup(struct phy_device *phydev)
+{
+	genphy_update_link(phydev);
+	et1011c_parse_status(phydev);
+	return 0;
+}
+
+static struct phy_driver et1011c_driver = {
+	.name		= "ET1011C",
+	.uid		= 0x0282f014,
+	.mask		= 0xfffffff0,
+	.features	= PHY_GBIT_FEATURES,
+	.config		= &et1011c_config,
+	.startup	= &et1011c_startup,
+};
+
+int phy_et1011c_init(void)
+{
+	phy_register(&et1011c_driver);
+
+	return 0;
+}
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index d0ed7666ed..f8c5481477 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -430,6 +430,9 @@ int phy_init(void)
 #ifdef CONFIG_PHY_DAVICOM
 	phy_davicom_init();
 #endif
+#ifdef CONFIG_PHY_ET1011C
+	phy_et1011c_init();
+#endif
 #ifdef CONFIG_PHY_LXT
 	phy_lxt_init();
 #endif
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index 1dac16a9f7..a9c42370f9 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -30,7 +30,7 @@ COBJS-$(CONFIG_FTPMU010_POWER)	+= ftpmu010.o
 COBJS-$(CONFIG_TPS6586X_POWER)	+= tps6586x.o
 COBJS-$(CONFIG_TWL4030_POWER)	+= twl4030.o
 COBJS-$(CONFIG_TWL6030_POWER)	+= twl6030.o
-COBJS-$(CONFIG_TWL6035_POWER)	+= twl6035.o
+COBJS-$(CONFIG_PALMAS_POWER)	+= palmas.o
 
 COBJS-$(CONFIG_POWER) += power_core.o
 COBJS-$(CONFIG_DIALOG_POWER) += power_dialog.o
diff --git a/drivers/power/palmas.c b/drivers/power/palmas.c
new file mode 100644
index 0000000000..09c832d8b6
--- /dev/null
+++ b/drivers/power/palmas.c
@@ -0,0 +1,52 @@
+/*
+ * (C) Copyright 2012-2013
+ * Texas Instruments, <www.ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <config.h>
+#include <palmas.h>
+
+void palmas_init_settings(void)
+{
+	return;
+}
+
+int palmas_mmc1_poweron_ldo(void)
+{
+	u8 val = 0;
+
+	/* set LDO9 TWL6035 to 3V */
+	val = 0x2b; /* (3 -.9)*28 +1 */
+
+	if (palmas_i2c_write_u8(0x48, LDO9_VOLTAGE, val)) {
+		printf("twl6035: could not set LDO9 voltage.\n");
+		return 1;
+	}
+
+	/* TURN ON LDO9 */
+	val = LDO_ON | LDO_MODE_SLEEP | LDO_MODE_ACTIVE;
+
+	if (palmas_i2c_write_u8(0x48, LDO9_CTRL, val)) {
+		printf("twl6035: could not turn on LDO9.\n");
+		return 1;
+	}
+
+	return 0;
+}
diff --git a/drivers/power/twl4030.c b/drivers/power/twl4030.c
index e7d5f132b2..6610f787d0 100644
--- a/drivers/power/twl4030.c
+++ b/drivers/power/twl4030.c
@@ -45,14 +45,14 @@
 void twl4030_power_reset_init(void)
 {
 	u8 val = 0;
-	if (twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER, &val,
-				TWL4030_PM_MASTER_P1_SW_EVENTS)) {
+	if (twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER,
+				TWL4030_PM_MASTER_P1_SW_EVENTS, &val)) {
 		printf("Error:TWL4030: failed to read the power register\n");
 		printf("Could not initialize hardware reset\n");
 	} else {
 		val |= TWL4030_PM_MASTER_SW_EVENTS_STOPON_PWRON;
-		if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, val,
-					 TWL4030_PM_MASTER_P1_SW_EVENTS)) {
+		if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+					 TWL4030_PM_MASTER_P1_SW_EVENTS, val)) {
 			printf("Error:TWL4030: failed to write the power register\n");
 			printf("Could not initialize hardware reset\n");
 		}
@@ -68,8 +68,8 @@ void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val,
 	int ret;
 
 	/* Select the Voltage */
-	ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, vsel_val,
-				vsel_reg);
+	ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, vsel_reg,
+				   vsel_val);
 	if (ret != 0) {
 		printf("Could not write vsel to reg %02x (%d)\n",
 			vsel_reg, ret);
@@ -77,8 +77,8 @@ void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val,
 	}
 
 	/* Select the Device Group (enable the supply if dev_grp_sel != 0) */
-	ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, dev_grp_sel,
-				dev_grp);
+	ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, dev_grp,
+				   dev_grp_sel);
 	if (ret != 0)
 		printf("Could not write grp_sel to reg %02x (%d)\n",
 			dev_grp, ret);
diff --git a/drivers/power/twl6030.c b/drivers/power/twl6030.c
index c5a0038cad..d421e6005b 100644
--- a/drivers/power/twl6030.c
+++ b/drivers/power/twl6030.c
@@ -25,30 +25,19 @@
 
 #include <twl6030.h>
 
-/* Functions to read and write from TWL6030 */
-static inline int twl6030_i2c_write_u8(u8 chip_no, u8 val, u8 reg)
-{
-	return i2c_write(chip_no, reg, 1, &val, 1);
-}
-
-static inline int twl6030_i2c_read_u8(u8 chip_no, u8 *val, u8 reg)
-{
-	return i2c_read(chip_no, reg, 1, val, 1);
-}
-
 static int twl6030_gpadc_read_channel(u8 channel_no)
 {
 	u8 lsb = 0;
 	u8 msb = 0;
 	int ret = 0;
 
-	ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, &lsb,
-				GPCH0_LSB + channel_no * 2);
+	ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC,
+				  GPCH0_LSB + channel_no * 2, &lsb);
 	if (ret)
 		return ret;
 
-	ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, &msb,
-				GPCH0_MSB + channel_no * 2);
+	ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC,
+				  GPCH0_MSB + channel_no * 2, &msb);
 	if (ret)
 		return ret;
 
@@ -60,7 +49,7 @@ static int twl6030_gpadc_sw2_trigger(void)
 	u8 val;
 	int ret = 0;
 
-	ret = twl6030_i2c_write_u8(TWL6030_CHIP_ADC, CTRL_P2_SP2, CTRL_P2);
+	ret = twl6030_i2c_write_u8(TWL6030_CHIP_ADC, CTRL_P2, CTRL_P2_SP2);
 	if (ret)
 		return ret;
 
@@ -68,7 +57,7 @@ static int twl6030_gpadc_sw2_trigger(void)
 	val =  CTRL_P2_BUSY;
 
 	while (!((val & CTRL_P2_EOCP2) && (!(val & CTRL_P2_BUSY)))) {
-		ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, &val, CTRL_P2);
+		ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, CTRL_P2, &val);
 		if (ret)
 			return ret;
 		udelay(1000);
@@ -79,29 +68,29 @@ static int twl6030_gpadc_sw2_trigger(void)
 
 void twl6030_stop_usb_charging(void)
 {
-	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, 0, CONTROLLER_CTRL1);
+	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CONTROLLER_CTRL1, 0);
 
 	return;
 }
 
 void twl6030_start_usb_charging(void)
 {
-	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CHARGERUSB_VICHRG_1500,
-							CHARGERUSB_VICHRG);
-	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CHARGERUSB_CIN_LIMIT_NONE,
-							CHARGERUSB_CINLIMIT);
-	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, MBAT_TEMP,
-							CONTROLLER_INT_MASK);
-	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, MASK_MCHARGERUSB_THMREG,
-							CHARGERUSB_INT_MASK);
-	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CHARGERUSB_VOREG_4P0,
-							CHARGERUSB_VOREG);
-	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CHARGERUSB_CTRL2_VITERM_400,
-							CHARGERUSB_CTRL2);
-	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, TERM, CHARGERUSB_CTRL1);
+	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+			     CHARGERUSB_VICHRG, CHARGERUSB_VICHRG_1500);
+	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+			     CHARGERUSB_CINLIMIT, CHARGERUSB_CIN_LIMIT_NONE);
+	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+			     CONTROLLER_INT_MASK, MBAT_TEMP);
+	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+			     CHARGERUSB_INT_MASK, MASK_MCHARGERUSB_THMREG);
+	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+			     CHARGERUSB_VOREG, CHARGERUSB_VOREG_4P0);
+	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+			     CHARGERUSB_CTRL2, CHARGERUSB_CTRL2_VITERM_400);
+	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CHARGERUSB_CTRL1, TERM);
 	/* Enable USB charging */
-	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CONTROLLER_CTRL1_EN_CHARGER,
-							CONTROLLER_CTRL1);
+	twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+			     CONTROLLER_CTRL1, CONTROLLER_CTRL1_EN_CHARGER);
 	return;
 }
 
@@ -111,8 +100,8 @@ int twl6030_get_battery_current(void)
 	u8 msb = 0;
 	u8 lsb = 0;
 
-	twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, &msb, FG_REG_11);
-	twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, &lsb, FG_REG_10);
+	twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, FG_REG_11, &msb);
+	twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, FG_REG_10, &lsb);
 	battery_current = ((msb << 8) | lsb);
 
 	/* convert 10 bit signed number to 16 bit signed number */
@@ -156,10 +145,10 @@ void twl6030_init_battery_charging(void)
 	int ret = 0;
 
 	/* Enable VBAT measurement */
-	twl6030_i2c_write_u8(TWL6030_CHIP_PM, VBAT_MEAS, MISC1);
+	twl6030_i2c_write_u8(TWL6030_CHIP_PM, MISC1, VBAT_MEAS);
 
 	/* Enable GPADC module */
-	ret = twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, FGS | GPADCS, TOGGLE1);
+	ret = twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, TOGGLE1, FGS | GPADCS);
 	if (ret) {
 		printf("Failed to enable GPADC\n");
 		return;
@@ -173,7 +162,7 @@ void twl6030_init_battery_charging(void)
 		printf("Main battery voltage too low!\n");
 
 	/* Check for the presence of USB charger */
-	twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, &stat1, CONTROLLER_STAT1);
+	twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, CONTROLLER_STAT1, &stat1);
 
 	/* check for battery presence indirectly via Fuel gauge */
 	if ((stat1 & VBUS_DET) && (battery_volt < 3300))
@@ -185,8 +174,8 @@ void twl6030_init_battery_charging(void)
 void twl6030_power_mmc_init()
 {
 	/* set voltage to 3.0 and turnon for APP */
-	twl6030_i2c_write_u8(TWL6030_CHIP_PM, 0x15, VMMC_CFG_VOLTATE);
-	twl6030_i2c_write_u8(TWL6030_CHIP_PM, 0x21, VMMC_CFG_STATE);
+	twl6030_i2c_write_u8(TWL6030_CHIP_PM, VMMC_CFG_VOLTATE, 0x15);
+	twl6030_i2c_write_u8(TWL6030_CHIP_PM, VMMC_CFG_STATE, 0x21);
 }
 
 void twl6030_usb_device_settings()
@@ -194,12 +183,12 @@ void twl6030_usb_device_settings()
 	u8 data = 0;
 
 	/* Select APP Group and set state to ON */
-	twl6030_i2c_write_u8(TWL6030_CHIP_PM, 0x21, VUSB_CFG_STATE);
+	twl6030_i2c_write_u8(TWL6030_CHIP_PM, VUSB_CFG_STATE, 0x21);
 
-	twl6030_i2c_read_u8(TWL6030_CHIP_PM, &data, MISC2);
+	twl6030_i2c_read_u8(TWL6030_CHIP_PM, MISC2, &data);
 	data |= 0x10;
 
 	/* Select the input supply for VBUS regulator */
-	twl6030_i2c_write_u8(TWL6030_CHIP_PM, data, MISC2);
+	twl6030_i2c_write_u8(TWL6030_CHIP_PM, MISC2, data);
 }
 #endif
diff --git a/drivers/power/twl6035.c b/drivers/power/twl6035.c
deleted file mode 100644
index d3de698cde..0000000000
--- a/drivers/power/twl6035.c
+++ /dev/null
@@ -1,74 +0,0 @@
-/*
- * (C) Copyright 2012
- * Texas Instruments, <www.ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <config.h>
-#include <twl6035.h>
-
-/* Functions to read and write from TWL6030 */
-int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg)
-{
-	return i2c_write(chip_no, reg, 1, &val, 1);
-}
-
-int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg)
-{
-	return i2c_read(chip_no, reg, 1, val, 1);
-}
-
-/* To align with i2c mw/mr address, reg, val command syntax */
-static inline int palmas_write_u8(u8 chip_no, u8 reg, u8 val)
-{
-	return i2c_write(chip_no, reg, 1, &val, 1);
-}
-
-static inline int palmas_read_u8(u8 chip_no, u8 reg, u8 *val)
-{
-	return i2c_read(chip_no, reg, 1, val, 1);
-}
-
-void twl6035_init_settings(void)
-{
-	return;
-}
-
-int twl6035_mmc1_poweron_ldo(void)
-{
-	u8 val = 0;
-
-	/* set LDO9 TWL6035 to 3V */
-	val = 0x2b; /* (3 -.9)*28 +1 */
-
-	if (palmas_write_u8(0x48, LDO9_VOLTAGE, val)) {
-		printf("twl6035: could not set LDO9 voltage.\n");
-		return 1;
-	}
-
-	/* TURN ON LDO9 */
-	val = LDO_ON | LDO_MODE_SLEEP | LDO_MODE_ACTIVE;
-
-	if (palmas_write_u8(0x48, LDO9_CTRL, val)) {
-		printf("twl6035: could not turn on LDO9.\n");
-		return 1;
-	}
-
-	return 0;
-}
diff --git a/drivers/usb/phy/twl4030.c b/drivers/usb/phy/twl4030.c
index 54d2e615c8..74f1dccbd4 100644
--- a/drivers/usb/phy/twl4030.c
+++ b/drivers/usb/phy/twl4030.c
@@ -54,7 +54,7 @@ static int twl4030_usb_write(u8 address, u8 data)
 {
 	int ret;
 
-	ret = twl4030_i2c_write_u8(TWL4030_CHIP_USB, data, address);
+	ret = twl4030_i2c_write_u8(TWL4030_CHIP_USB, address, data);
 	if (ret != 0)
 		printf("TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
 
@@ -66,7 +66,7 @@ static int twl4030_usb_read(u8 address)
 	u8 data;
 	int ret;
 
-	ret = twl4030_i2c_read_u8(TWL4030_CHIP_USB, &data, address);
+	ret = twl4030_i2c_read_u8(TWL4030_CHIP_USB, address, &data);
 	if (ret == 0)
 		ret = data;
 	else
@@ -78,40 +78,40 @@ static int twl4030_usb_read(u8 address)
 static void twl4030_usb_ldo_init(void)
 {
 	/* Enable writing to power configuration registers */
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0xC0,
-			     TWL4030_PM_MASTER_PROTECT_KEY);
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x0C,
-			     TWL4030_PM_MASTER_PROTECT_KEY);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+			     TWL4030_PM_MASTER_PROTECT_KEY, 0xC0);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+			     TWL4030_PM_MASTER_PROTECT_KEY, 0x0C);
 
 	/* put VUSB3V1 LDO in active state */
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00,
-			     TWL4030_PM_RECEIVER_VUSB_DEDICATED2);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+			     TWL4030_PM_RECEIVER_VUSB_DEDICATED2, 0x00);
 
 	/* input to VUSB3V1 LDO is from VBAT, not VBUS */
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x14,
-			     TWL4030_PM_RECEIVER_VUSB_DEDICATED1);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+			     TWL4030_PM_RECEIVER_VUSB_DEDICATED1, 0x14);
 
 	/* turn on 3.1V regulator */
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20,
-			     TWL4030_PM_RECEIVER_VUSB3V1_DEV_GRP);
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00,
-			     TWL4030_PM_RECEIVER_VUSB3V1_TYPE);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+			     TWL4030_PM_RECEIVER_VUSB3V1_DEV_GRP, 0x20);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+			     TWL4030_PM_RECEIVER_VUSB3V1_TYPE, 0x00);
 
 	/* turn on 1.5V regulator */
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20,
-			     TWL4030_PM_RECEIVER_VUSB1V5_DEV_GRP);
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00,
-			     TWL4030_PM_RECEIVER_VUSB1V5_TYPE);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+			     TWL4030_PM_RECEIVER_VUSB1V5_DEV_GRP, 0x20);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+			     TWL4030_PM_RECEIVER_VUSB1V5_TYPE, 0x00);
 
 	/* turn on 1.8V regulator */
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20,
-			     TWL4030_PM_RECEIVER_VUSB1V8_DEV_GRP);
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00,
-			     TWL4030_PM_RECEIVER_VUSB1V8_TYPE);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+			     TWL4030_PM_RECEIVER_VUSB1V8_DEV_GRP, 0x20);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+			     TWL4030_PM_RECEIVER_VUSB1V8_TYPE, 0x00);
 
 	/* disable access to power configuration registers */
-	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x00,
-			     TWL4030_PM_MASTER_PROTECT_KEY);
+	twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+			     TWL4030_PM_MASTER_PROTECT_KEY, 0x00);
 }
 
 static void twl4030_phy_power(void)
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index ef00306a55..f019134216 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -17,6 +17,7 @@
 #define __CONFIG_AM335X_EVM_H
 
 #define CONFIG_AM33XX
+#define CONFIG_OMAP
 
 #include <asm/arch/omap.h>
 
@@ -196,7 +197,6 @@
 					+ (8 * 1024 * 1024))
 
 #define CONFIG_SYS_LOAD_ADDR		0x81000000 /* Default load address */
-#define CONFIG_SYS_HZ			1000 /* 1ms clock */
 
 #define CONFIG_MMC
 #define CONFIG_GENERIC_MMC
@@ -260,12 +260,11 @@
  /* Platform/Board specific defs */
 #define CONFIG_SYS_TIMERBASE		0x48040000	/* Use Timer2 */
 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
-#define CONFIG_SYS_HZ			1000
+#define CONFIG_SYS_HZ			1000	/* 1ms clock */
 
 /* NS16550 Configuration */
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SERIAL_MULTI
 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
 #define CONFIG_SYS_NS16550_CLK		(48000000)
 #define CONFIG_SYS_NS16550_COM1		0x44e09000	/* Base EVM has UART0 */
@@ -295,6 +294,9 @@
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 110, 300, 600, 1200, 2400, \
 4800, 9600, 14400, 19200, 28800, 38400, 56000, 57600, 115200 }
 
+/* CPU */
+#define CONFIG_ARCH_CPU_INIT
+
 #define CONFIG_ENV_OVERWRITE		1
 #define CONFIG_SYS_CONSOLE_INFO_QUIET
 
@@ -360,11 +362,7 @@
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	14
 
-#define CONFIG_SYS_NAND_ECCSTEPS	4
-#define	CONFIG_SYS_NAND_ECCTOTAL	(CONFIG_SYS_NAND_ECCBYTES * \
-						CONFIG_SYS_NAND_ECCSTEPS)
-
-#define	CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
 
diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index 726714dd21..c6e357a8ce 100644
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -135,12 +135,12 @@
 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_EXT2		/* EXT2 Support			*/
 #define CONFIG_CMD_FAT		/* FAT support			*/
-#define CONFIG_CMD_JFFS2	/* JFFS2 Support		*/
 #define CONFIG_CMD_MTDPARTS	/* Enable MTD parts commands */
 #define CONFIG_MTD_DEVICE	/* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
 #define MTDIDS_DEFAULT		"nand0=nand"
 #define MTDPARTS_DEFAULT	"mtdparts=nand:512k(x-loader),"\
-				"1920k(u-boot),128k(u-boot-env),"\
+				"1920k(u-boot),256k(u-boot-env),"\
 				"4m(kernel),-(fs)"
 
 #define CONFIG_CMD_I2C		/* I2C serial bus support	*/
@@ -182,14 +182,6 @@
 
 #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of NAND */
 							/* devices */
-#define CONFIG_JFFS2_NAND
-/* nand device jffs2 lives on */
-#define CONFIG_JFFS2_DEV		"nand0"
-/* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_OFFSET	0x680000
-#define CONFIG_JFFS2_PART_SIZE		0xf980000	/* size of jffs2 */
-							/* partition */
-
 /* Environment information */
 #define CONFIG_BOOTDELAY		10
 #define CONFIG_ZERO_BOOTDELAY_CHECK
@@ -204,9 +196,9 @@
 	"defaultdisplay=dvi\0" \
 	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
-	"mmcrootfstype=ext3 rootwait\0" \
+	"mmcrootfstype=ext4 rootwait\0" \
 	"nandroot=/dev/mtdblock4 rw\0" \
-	"nandrootfstype=jffs2\0" \
+	"nandrootfstype=ubifs\0" \
 	"mmcargs=setenv bootargs console=${console} " \
 		"mpurate=${mpurate} " \
 		"vram=${vram} " \
@@ -232,7 +224,7 @@
 		"bootm ${loadaddr}\0" \
 	"nandboot=echo Booting from nand ...; " \
 		"run nandargs; " \
-		"nand read ${loadaddr} 280000 400000; " \
+		"nand read ${loadaddr} 2a0000 400000; " \
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
diff --git a/include/configs/da830evm.h b/include/configs/da830evm.h
index f7ac256a0f..198892ba57 100644
--- a/include/configs/da830evm.h
+++ b/include/configs/da830evm.h
@@ -109,8 +109,8 @@
 #define CONFIG_SYS_NAND_CS		3
 #define CONFIG_SYS_NAND_BASE		DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
 #define CONFIG_SYS_NAND_PAGE_2K
-#define CONFIG_SYS_CLE_MASK		0x10
-#define CONFIG_SYS_ALE_MASK		0x8
+#define CONFIG_SYS_NAND_MASK_CLE		0x10
+#define CONFIG_SYS_NAND_MASK_ALE		0x8
 #define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
 #endif
 
diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h
index 583568d309..c420967411 100644
--- a/include/configs/da850evm.h
+++ b/include/configs/da850evm.h
@@ -199,8 +199,8 @@
 #define	CONFIG_SYS_NAND_PAGE_2K
 #define CONFIG_SYS_NAND_CS		3
 #define CONFIG_SYS_NAND_BASE		DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
-#define CONFIG_SYS_CLE_MASK		0x10
-#define CONFIG_SYS_ALE_MASK		0x8
+#define CONFIG_SYS_NAND_MASK_CLE		0x10
+#define CONFIG_SYS_NAND_MASK_ALE		0x8
 #undef CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
diff --git a/include/configs/enbw_cmc.h b/include/configs/enbw_cmc.h
index 2d63b670cd..97bc9729a1 100644
--- a/include/configs/enbw_cmc.h
+++ b/include/configs/enbw_cmc.h
@@ -118,8 +118,8 @@
 #define CONFIG_SYS_NAND_PAGE_2K
 #define CONFIG_SYS_NAND_CS		3
 #define CONFIG_SYS_NAND_BASE		DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
-#define CONFIG_SYS_CLE_MASK		0x10
-#define CONFIG_SYS_ALE_MASK		0x8
+#define CONFIG_SYS_NAND_MASK_CLE		0x10
+#define CONFIG_SYS_NAND_MASK_ALE		0x8
 #undef CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
 
diff --git a/include/configs/igep0033.h b/include/configs/igep0033.h
new file mode 100644
index 0000000000..1912d7df37
--- /dev/null
+++ b/include/configs/igep0033.h
@@ -0,0 +1,288 @@
+/*
+ * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __CONFIG_IGEP0033_H
+#define __CONFIG_IGEP0033_H
+
+#define CONFIG_AM33XX
+#define CONFIG_OMAP
+
+#include <asm/arch/omap.h>
+
+/* Mach type */
+#define MACH_TYPE_IGEP0033		4521	/* Until the next sync */
+#define CONFIG_MACH_TYPE		MACH_TYPE_IGEP0033
+
+/* Clock defines */
+#define V_OSCK				24000000  /* Clock output from T2 */
+#define V_SCLK				(V_OSCK)
+
+/* DMA defines */
+#define CONFIG_DMA_COHERENT
+#define CONFIG_DMA_COHERENT_SIZE	(1 << 20)
+
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
+#define CONFIG_SYS_MALLOC_LEN		(1024 << 10)
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
+#define CONFIG_SYS_PROMPT		"U-Boot# "
+#define CONFIG_SYS_NO_FLASH
+
+/* Display cpuinfo */
+#define CONFIG_DISPLAY_CPUINFO
+
+/* Commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+
+/*
+ * Because the issues explained in doc/README.memory-test, the "mtest command
+ * is considered deprecated. It should not be enabled in most normal ports of
+ * U-Boot.
+ */
+#undef CONFIG_CMD_MEMTEST
+
+#define CONFIG_BOOTDELAY		1	/* negative for no autoboot */
+#define CONFIG_ENV_VARS_UBOOT_CONFIG
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"loadaddr=0x80200000\0" \
+	"rdaddr=0x81000000\0" \
+	"bootfile=/boot/uImage\0" \
+	"console=ttyO0,115200n8\0" \
+	"optargs=\0" \
+	"mmcdev=0\0" \
+	"mmcroot=/dev/mmcblk0p2 rw\0" \
+	"mmcrootfstype=ext4 rootwait\0" \
+	"ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=${rdaddr},64M\0" \
+	"ramrootfstype=ext2\0" \
+	"mmcargs=setenv bootargs console=${console} " \
+		"${optargs} " \
+		"root=${mmcroot} " \
+		"rootfstype=${mmcrootfstype}\0" \
+	"bootenv=uEnv.txt\0" \
+	"loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
+	"importbootenv=echo Importing environment from mmc ...; " \
+		"env import -t $loadaddr $filesize\0" \
+	"ramargs=setenv bootargs console=${console} " \
+		"${optargs} " \
+		"root=${ramroot} " \
+		"rootfstype=${ramrootfstype}\0" \
+	"loadramdisk=load mmc ${mmcdev} ${rdaddr} ramdisk.gz\0" \
+	"loaduimagefat=load mmc ${mmcdev} ${loadaddr} ${bootfile}\0" \
+	"loaduimage=load mmc ${mmcdev}:2 ${loadaddr} ${bootfile}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"bootm ${loadaddr}\0" \
+	"ramboot=echo Booting from ramdisk ...; " \
+		"run ramargs; " \
+		"bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+	"mmc dev ${mmcdev}; if mmc rescan; then " \
+		"echo SD/MMC found on device ${mmcdev};" \
+		"if run loadbootenv; then " \
+			"echo Loaded environment from ${bootenv};" \
+			"run importbootenv;" \
+		"fi;" \
+		"if test -n $uenvcmd; then " \
+			"echo Running uenvcmd ...;" \
+			"run uenvcmd;" \
+		"fi;" \
+		"if run loaduimage; then " \
+			"run mmcboot;" \
+		"fi;" \
+	"fi;" \
+
+/* Max number of command args */
+#define CONFIG_SYS_MAXARGS		16
+
+/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE		512
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
+					+ sizeof(CONFIG_SYS_PROMPT) + 16)
+
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_LOAD_ADDR		0x81000000 /* Default load address */
+#define CONFIG_SYS_HZ			1000 /* 1ms clock */
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1		/*  1 bank of DRAM */
+#define PHYS_DRAM_1			0x80000000	/* DRAM Bank #1 */
+#define CONFIG_MAX_RAM_BANK_SIZE	(1024 << 20)	/* 1GB */
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_DRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR         (NON_SECURE_SRAM_END - \
+						GENERATED_GBL_DATA_SIZE)
+/* Platform/Board specific defs */
+#define CONFIG_SYS_TIMERBASE		0x48040000	/* Use Timer2 */
+#define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ			1000
+
+/* NS16550 Configuration */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		(48000000)
+#define CONFIG_SYS_NS16550_COM1		0x44e09000	/* UART0 */
+
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+
+/* CPU */
+#define CONFIG_ARCH_CPU_INIT
+
+#define CONFIG_ENV_OVERWRITE		1
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+
+/* MMC support */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_DOS_PARTITION
+
+/* GPIO support */
+#define CONFIG_OMAP_GPIO
+
+/* Ethernet support */
+#define CONFIG_DRIVER_TI_CPSW
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_NET_RETRY_COUNT         10
+#define CONFIG_NET_MULTI
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR			0
+#define CONFIG_PHY_SMSC
+
+/* NAND support */
+#define CONFIG_NAND
+#define CONFIG_NAND_OMAP_GPMC
+#define GPMC_NAND_ECC_LP_x16_LAYOUT	1
+#define CONFIG_SYS_NAND_BASE		(0x08000000)	/* phys address CS0 */
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_ONFI_DETECTION	1
+#define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET		0x260000 /* environment starts here */
+
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+
+#define MTDIDS_DEFAULT			"nand0=nand"
+#define MTDPARTS_DEFAULT		"mtdparts=nand:512k(SPL),"\
+					"1m(U-Boot),128k(U-Boot Env),"\
+					"5m(Kernel),-(File System)"
+
+/* Unsupported features */
+#undef CONFIG_USE_IRQ
+
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE		0x402F0400
+#define CONFIG_SPL_MAX_SIZE		(101 * 1024)
+#define CONFIG_SPL_STACK		CONFIG_SYS_INIT_SP_ADDR
+
+#define CONFIG_SPL_BSS_START_ADDR	0x80000000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x80000		/* 512 KB */
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION	1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME	"u-boot.img"
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_YMODEM_SUPPORT
+#define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/am33xx/u-boot-spl.lds"
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_NAND_AM33XX_BCH
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT	(CONFIG_SYS_NAND_BLOCK_SIZE / \
+					 CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_PAGE_SIZE	2048
+#define CONFIG_SYS_NAND_OOBSIZE		64
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS		{ 2, 3, 4, 5, 6, 7, 8, 9, \
+					 10, 11, 12, 13, 14, 15, 16, 17, \
+					 18, 19, 20, 21, 22, 23, 24, 25, \
+					 26, 27, 28, 29, 30, 31, 32, 33, \
+					 34, 35, 36, 37, 38, 39, 40, 41, \
+					 42, 43, 44, 45, 46, 47, 48, 49, \
+					 50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE		512
+#define CONFIG_SYS_NAND_ECCBYTES	14
+
+#define CONFIG_SYS_NAND_ECCSTEPS	4
+#define	CONFIG_SYS_NAND_ECCTOTAL	(CONFIG_SYS_NAND_ECCBYTES * \
+						CONFIG_SYS_NAND_ECCSTEPS)
+
+#define	CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
+
+/*
+ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
+ * 64 bytes before this address should be set aside for u-boot.img's
+ * header. That is 0x800FFFC0--0x80100000 should not be used for any
+ * other needs.
+ */
+#define CONFIG_SYS_TEXT_BASE		0x80800000
+#define CONFIG_SYS_SPL_MALLOC_START	0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
+
+/*
+ * Since SPL did pll and ddr initialization for us,
+ * we don't need to do it twice.
+ */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#endif
+
+#endif	/* ! __CONFIG_IGEP0033_H */
diff --git a/include/configs/omap4_common.h b/include/configs/omap4_common.h
index 1fd3097d75..d6448b0529 100644
--- a/include/configs/omap4_common.h
+++ b/include/configs/omap4_common.h
@@ -87,6 +87,10 @@
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
 					115200}
+
+/* CPU */
+#define CONFIG_ARCH_CPU_INIT
+
 /* I2C  */
 #define CONFIG_HARD_I2C			1
 #define CONFIG_SYS_I2C_SPEED		100000
@@ -176,7 +180,9 @@
 		"if test $board_name = sdp4430; then " \
 			"setenv fdtfile omap4-sdp.dtb; fi; " \
 		"if test $board_name = panda; then " \
-			"setenv fdtfile omap4-panda-es.dtb; fi\0" \
+			"setenv fdtfile omap4-panda.dtb; fi;" \
+		"if test $board_name = panda-es; then " \
+			"setenv fdtfile omap4-panda-es.dtb; fi; \0" \
 	"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
 
 #define CONFIG_BOOTCOMMAND \
diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h
index eacb5f5c3b..abf586b872 100644
--- a/include/configs/omap4_panda.h
+++ b/include/configs/omap4_panda.h
@@ -66,4 +66,6 @@
 
 #define CONFIG_SYS_PROMPT		"Panda # "
 
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
 #endif /* __CONFIG_PANDA_H */
diff --git a/include/configs/omap5_common.h b/include/configs/omap5_common.h
index c21c387cba..deb5e9fd5e 100644
--- a/include/configs/omap5_common.h
+++ b/include/configs/omap5_common.h
@@ -86,6 +86,9 @@
 
 #define CONFIG_BAUDRATE			115200
 
+/* CPU */
+#define CONFIG_ARCH_CPU_INIT
+
 /* I2C  */
 #define CONFIG_HARD_I2C
 #define CONFIG_SYS_I2C_SPEED		100000
@@ -150,10 +153,12 @@
 	"usbtty=cdc_acm\0" \
 	"vram=16M\0" \
 	"partitions=" PARTS_DEFAULT "\0" \
+	"optargs=\0" \
 	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext4 rootwait\0" \
 	"mmcargs=setenv bootargs console=${console} " \
+		"${optargs} " \
 		"vram=${vram} " \
 		"root=${mmcroot} " \
 		"rootfstype=${mmcrootfstype}\0" \
diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h
index 550cabd77c..9e0339b31b 100644
--- a/include/configs/omap5_uevm.h
+++ b/include/configs/omap5_uevm.h
@@ -37,7 +37,7 @@
 
 /* TWL6035 */
 #ifndef CONFIG_SPL_BUILD
-#define CONFIG_TWL6035_POWER
+#define CONFIG_PALMAS_POWER
 #endif
 
 /* MMC ENV related defines */
@@ -56,4 +56,5 @@
 
 #define CONFIG_SYS_PROMPT		"OMAP5430 EVM # "
 
+#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC	16296
 #endif /* __CONFIG_OMAP5_EVM_H */
diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h
index d0ea74e0b4..478f805b7c 100644
--- a/include/configs/pcm051.h
+++ b/include/configs/pcm051.h
@@ -20,6 +20,7 @@
 #define __CONFIG_PCM051_H
 
 #define CONFIG_AM33XX
+#define CONFIG_OMAP
 
 #include <asm/arch/omap.h>
 
@@ -129,7 +130,6 @@
 					+ (8 * 1024 * 1024))
 
 #define CONFIG_SYS_LOAD_ADDR		0x80007fc0 /* Default load address */
-#define CONFIG_SYS_HZ			1000 /* 1ms clock */
 
 #define CONFIG_MMC
 #define CONFIG_GENERIC_MMC
@@ -158,13 +158,12 @@
  /* Platform/Board specific defs */
 #define CONFIG_SYS_TIMERBASE		0x48040000	/* Use Timer2 */
 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
-#define CONFIG_SYS_HZ			1000
+#define CONFIG_SYS_HZ			1000	/* 1ms clock */
 
 #define CONFIG_CONS_INDEX		1
 /* NS16550 Configuration */
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SERIAL_MULTI
 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
 #define CONFIG_SYS_NS16550_CLK		(48000000)
 #define CONFIG_SYS_NS16550_COM1		0x44e09000	/* Base EVM has UART0 */
@@ -194,6 +193,9 @@
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 110, 300, 600, 1200, 2400, \
 4800, 9600, 14400, 19200, 28800, 38400, 56000, 57600, 115200 }
 
+/* CPU */
+#define CONFIG_ARCH_CPU_INIT
+
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SYS_CONSOLE_INFO_QUIET
 
diff --git a/include/configs/ti814x_evm.h b/include/configs/ti814x_evm.h
index 16547e3314..eac5ad0243 100644
--- a/include/configs/ti814x_evm.h
+++ b/include/configs/ti814x_evm.h
@@ -19,6 +19,7 @@
 #define CONFIG_TI81XX
 #define CONFIG_TI814X
 #define CONFIG_SYS_NO_FLASH
+#define CONFIG_OMAP
 
 #include <asm/arch/omap.h>
 
@@ -162,6 +163,9 @@
 
 #define CONFIG_BAUDRATE			115200
 
+/* CPU */
+#define CONFIG_ARCH_CPU_INIT
+
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_CONS_INDEX		1
 #define CONFIG_SYS_CONSOLE_INFO_QUIET
@@ -218,4 +222,25 @@
 /* Unsupported features */
 #undef CONFIG_USE_IRQ
 
+/* Ethernet */
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
+#define CONFIG_DRIVER_TI_CPSW
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_NET_RETRY_COUNT         10
+#define CONFIG_NET_MULTI
+#define CONFIG_PHY_GIGE
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR			1
+#define CONFIG_PHY_ET1011C
+#define CONFIG_PHY_ET1011C_TX_CLK_FIX
+
 #endif	/* ! __CONFIG_TI814X_EVM_H */
diff --git a/include/configs/tnetv107x_evm.h b/include/configs/tnetv107x_evm.h
index d6371fce4d..cabc06e5ba 100644
--- a/include/configs/tnetv107x_evm.h
+++ b/include/configs/tnetv107x_evm.h
@@ -82,8 +82,8 @@
 #define CONFIG_SYS_NAND_CS		2
 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 #define CONFIG_SYS_NAND_BASE		TNETV107X_ASYNC_EMIF_DATA_CE0_BASE
-#define CONFIG_SYS_CLE_MASK		0x10
-#define CONFIG_SYS_ALE_MASK		0x8
+#define CONFIG_SYS_NAND_MASK_CLE		0x10
+#define CONFIG_SYS_NAND_MASK_ALE		0x8
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_MTD_PARTITIONS
 #define CONFIG_CMD_MTDPARTS
diff --git a/include/palmas.h b/include/palmas.h
new file mode 100644
index 0000000000..3b185896d6
--- /dev/null
+++ b/include/palmas.h
@@ -0,0 +1,58 @@
+/*
+ * (C) Copyright 2012-2013
+ * Texas Instruments, <www.ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef PALMAS_H
+#define PALMAS_H
+
+#include <common.h>
+#include <i2c.h>
+
+/* I2C chip addresses */
+#define PALMAS_CHIP_ADDR	0x48
+
+/* 0x1XY translates to page 1, register address 0xXY */
+#define LDO9_CTRL		0x60
+#define LDO9_VOLTAGE		0x61
+
+/* Bit field definitions for LDOx_CTRL */
+#define LDO_ON			(1 << 4)
+#define LDO_MODE_SLEEP		(1 << 2)
+#define LDO_MODE_ACTIVE		(1 << 0)
+
+/*
+ * Functions to read and write from TPS659038/TWL6035/TWL6037
+ * or other Palmas family of TI PMICs
+ */
+static inline int palmas_i2c_write_u8(u8 chip_no, u8 reg, u8 val)
+{
+	return i2c_write(chip_no, reg, 1, &val, 1);
+}
+
+static inline int palmas_i2c_read_u8(u8 chip_no, u8 reg, u8 *val)
+{
+	return i2c_read(chip_no, reg, 1, val, 1);
+}
+
+void palmas_init_settings(void);
+int palmas_mmc1_poweron_ldo(void);
+
+#endif /* PALMAS_H */
diff --git a/include/phy.h b/include/phy.h
index 58ca2730c8..7b4ce744e1 100644
--- a/include/phy.h
+++ b/include/phy.h
@@ -223,6 +223,7 @@ int gen10g_discover_mmds(struct phy_device *phydev);
 int phy_atheros_init(void);
 int phy_broadcom_init(void);
 int phy_davicom_init(void);
+int phy_et1011c_init(void);
 int phy_lxt_init(void);
 int phy_marvell_init(void);
 int phy_micrel_init(void);
diff --git a/include/spl.h b/include/spl.h
index b40be8039c..4bc1dd13bb 100644
--- a/include/spl.h
+++ b/include/spl.h
@@ -44,7 +44,6 @@ struct spl_image_info {
 #define SPL_COPY_PAYLOAD_ONLY	1
 
 extern struct spl_image_info spl_image;
-extern u32 *boot_params_ptr;
 
 /* SPL common functions */
 void preloader_console_init(void);
diff --git a/include/twl4030.h b/include/twl4030.h
index 5aa184183e..569ad2773f 100644
--- a/include/twl4030.h
+++ b/include/twl4030.h
@@ -638,12 +638,12 @@
  *   examples are TWL4030_PM_RECEIVER_VMMC1_DEV_GRP and
  *   TWL4030_LED_LEDEN.
  */
-static inline int twl4030_i2c_write_u8(u8 chip_no, u8 val, u8 reg)
+static inline int twl4030_i2c_write_u8(u8 chip_no, u8 reg, u8 val)
 {
 	return i2c_write(chip_no, reg, 1, &val, 1);
 }
 
-static inline int twl4030_i2c_read_u8(u8 chip_no, u8 *val, u8 reg)
+static inline int twl4030_i2c_read_u8(u8 chip_no, u8 reg, u8 *val)
 {
 	return i2c_read(chip_no, reg, 1, val, 1);
 }
diff --git a/include/twl6030.h b/include/twl6030.h
index a9fcadbfef..029b21f710 100644
--- a/include/twl6030.h
+++ b/include/twl6030.h
@@ -21,6 +21,9 @@
  * MA 02111-1307 USA
  */
 
+#ifndef TWL6030_H
+#define TWL6030_H
+
 #include <common.h>
 #include <i2c.h>
 
@@ -126,6 +129,17 @@
 #define GPCH0_LSB	0x57
 #define GPCH0_MSB	0x58
 
+/* Functions to read and write from TWL6030 */
+static inline int twl6030_i2c_write_u8(u8 chip_no, u8 reg, u8 val)
+{
+	return i2c_write(chip_no, reg, 1, &val, 1);
+}
+
+static inline int twl6030_i2c_read_u8(u8 chip_no, u8 reg, u8 *val)
+{
+	return i2c_read(chip_no, reg, 1, val, 1);
+}
+
 void twl6030_init_battery_charging(void);
 void twl6030_usb_device_settings(void);
 void twl6030_start_usb_charging(void);
@@ -133,3 +147,5 @@ void twl6030_stop_usb_charging(void);
 int twl6030_get_battery_voltage(void);
 int twl6030_get_battery_current(void);
 void twl6030_power_mmc_init(void);
+
+#endif /* TWL6030_H */
diff --git a/include/twl6035.h b/include/twl6035.h
deleted file mode 100644
index ce74348d44..0000000000
--- a/include/twl6035.h
+++ /dev/null
@@ -1,42 +0,0 @@
-/*
- * (C) Copyright 2012
- * Texas Instruments, <www.ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <i2c.h>
-
-/* I2C chip addresses */
-#define TWL6035_CHIP_ADDR	0x48
-
-/* 0x1XY translates to page 1, register address 0xXY */
-#define LDO9_CTRL		0x60
-#define LDO9_VOLTAGE		0x61
-
-/* Bit field definitions for LDOx_CTRL */
-#define LDO_ON			(1 << 4)
-#define LDO_MODE_SLEEP		(1 << 2)
-#define LDO_MODE_ACTIVE		(1 << 0)
-
-int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg);
-int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg);
-void twl6035_init_settings(void);
-int twl6035_mmc1_poweron_ldo(void);