From: Masahiro Yamada Date: Mon, 15 Dec 2014 14:26:07 +0000 (+0900) Subject: powerpc: manroland: remove uc100, uc101, mucmc52, hmi1001 support X-Git-Tag: v2015.01~84 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=ceaf499b5050c439448d85473ec1f87a033f6248;p=u-boot powerpc: manroland: remove uc100, uc101, mucmc52, hmi1001 support These boards are still non-generic boards. Signed-off-by: Masahiro Yamada Cc: Heiko Schocher Cc: Stefan Roese --- diff --git a/arch/powerpc/cpu/mpc5xxx/Kconfig b/arch/powerpc/cpu/mpc5xxx/Kconfig index bd64ea694f..e2e9cb77b0 100644 --- a/arch/powerpc/cpu/mpc5xxx/Kconfig +++ b/arch/powerpc/cpu/mpc5xxx/Kconfig @@ -83,15 +83,6 @@ config TARGET_O3DNT config TARGET_DIGSY_MTC bool "Support digsy_mtc" -config TARGET_HMI1001 - bool "Support hmi1001" - -config TARGET_MUCMC52 - bool "Support mucmc52" - -config TARGET_UC101 - bool "Support uc101" - config TARGET_PCM030 bool "Support pcm030" @@ -124,9 +115,6 @@ source "board/inka4x0/Kconfig" source "board/intercontrol/digsy_mtc/Kconfig" source "board/ipek01/Kconfig" source "board/jupiter/Kconfig" -source "board/manroland/hmi1001/Kconfig" -source "board/manroland/mucmc52/Kconfig" -source "board/manroland/uc101/Kconfig" source "board/motionpro/Kconfig" source "board/munices/Kconfig" source "board/phytec/pcm030/Kconfig" diff --git a/arch/powerpc/cpu/mpc5xxx/ide.c b/arch/powerpc/cpu/mpc5xxx/ide.c index 03cd7fd4e0..9003b774ff 100644 --- a/arch/powerpc/cpu/mpc5xxx/ide.c +++ b/arch/powerpc/cpu/mpc5xxx/ide.c @@ -41,19 +41,11 @@ int ide_preinit (void) /* All sample codes do that... */ *(vu_long *) MPC5XXX_ATA_SHARE_COUNT = 0; -#if defined(CONFIG_UC101) - /* Configure and reset host */ - *(vu_long *) MPC5XXX_ATA_HOST_CONFIG = - MPC5xxx_ATA_HOSTCONF_SMR | MPC5xxx_ATA_HOSTCONF_FR; - udelay (10); - *(vu_long *) MPC5XXX_ATA_HOST_CONFIG = 0; -#else /* Configure and reset host */ *(vu_long *) MPC5XXX_ATA_HOST_CONFIG = MPC5xxx_ATA_HOSTCONF_IORDY | MPC5xxx_ATA_HOSTCONF_SMR | MPC5xxx_ATA_HOSTCONF_FR; udelay (10); *(vu_long *) MPC5XXX_ATA_HOST_CONFIG = MPC5xxx_ATA_HOSTCONF_IORDY; -#endif /* Disable prefetch on Commbus */ psdma->PtdCntrl |= 1; diff --git a/arch/powerpc/cpu/mpc8xx/Kconfig b/arch/powerpc/cpu/mpc8xx/Kconfig index 33fff0c78b..9eb7e17313 100644 --- a/arch/powerpc/cpu/mpc8xx/Kconfig +++ b/arch/powerpc/cpu/mpc8xx/Kconfig @@ -46,9 +46,6 @@ config TARGET_KUP4X config TARGET_ELPT860 bool "Support ELPT860" -config TARGET_UC100 - bool "Support uc100" - config TARGET_TQM823L bool "Support TQM823L" @@ -96,7 +93,6 @@ source "board/ivm/Kconfig" source "board/kup/kup4k/Kconfig" source "board/kup/kup4x/Kconfig" source "board/lwmon/Kconfig" -source "board/manroland/uc100/Kconfig" source "board/netvia/Kconfig" source "board/r360mpi/Kconfig" source "board/spd8xx/Kconfig" diff --git a/board/manroland/hmi1001/Kconfig b/board/manroland/hmi1001/Kconfig deleted file mode 100644 index 996a87f101..0000000000 --- a/board/manroland/hmi1001/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_HMI1001 - -config SYS_BOARD - default "hmi1001" - -config SYS_VENDOR - default "manroland" - -config SYS_CONFIG_NAME - default "hmi1001" - -endif diff --git a/board/manroland/hmi1001/MAINTAINERS b/board/manroland/hmi1001/MAINTAINERS deleted file mode 100644 index a66a98178c..0000000000 --- a/board/manroland/hmi1001/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -HMI1001 BOARD -#M: - -S: Maintained -F: board/manroland/hmi1001/ -F: include/configs/hmi1001.h -F: configs/hmi1001_defconfig diff --git a/board/manroland/hmi1001/Makefile b/board/manroland/hmi1001/Makefile deleted file mode 100644 index c29a665cc3..0000000000 --- a/board/manroland/hmi1001/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2003-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := hmi1001.o diff --git a/board/manroland/hmi1001/hmi1001.c b/board/manroland/hmi1001/hmi1001.c deleted file mode 100644 index 64bdd8f58f..0000000000 --- a/board/manroland/hmi1001/hmi1001.c +++ /dev/null @@ -1,301 +0,0 @@ -/* - * (C) Copyright 2003-2008 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004 - * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com. - * - * (C) Copyright 2004 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include - -#ifndef CONFIG_SYS_RAMBOOT -static void sdram_start (int hi_addr) -{ - long hi_addr_bit = hi_addr ? 0x01000000 : 0; - - /* unlock mode register */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit; - __asm__ volatile ("sync"); - - /* precharge all banks */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit; - __asm__ volatile ("sync"); - -#if SDRAM_DDR - /* set mode register: extended mode */ - *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE; - __asm__ volatile ("sync"); - - /* set mode register: reset DLL */ - *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000; - __asm__ volatile ("sync"); -#endif - - /* precharge all banks */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit; - __asm__ volatile ("sync"); - - /* auto refresh */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit; - __asm__ volatile ("sync"); - - /* set mode register */ - *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE; - __asm__ volatile ("sync"); - - /* normal operation */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit; - __asm__ volatile ("sync"); -} -#endif - -/* - * ATTENTION: Although partially referenced initdram does NOT make real use - * use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE - * is something else than 0x00000000. - */ - -phys_size_t initdram (int board_type) -{ - ulong dramsize = 0; -#ifndef CONFIG_SYS_RAMBOOT - ulong test1, test2; - uint svr, pvr; - - /* setup SDRAM chip selects */ - *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001c; /* 512MB at 0x0 */ - *(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x40000000; /* disabled */ - __asm__ volatile ("sync"); - - /* setup config registers */ - *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1; - *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2; - __asm__ volatile ("sync"); - -#if SDRAM_DDR - /* set tap delay */ - *(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY; - __asm__ volatile ("sync"); -#endif - - /* find RAM size using SDRAM CS0 only */ - sdram_start(0); - test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000); - sdram_start(1); - test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000); - if (test1 > test2) { - sdram_start(0); - dramsize = test1; - } else { - dramsize = test2; - } - - /* memory smaller than 1MB is impossible */ - if (dramsize < (1 << 20)) { - dramsize = 0; - } - - /* set SDRAM CS0 size according to the amount of RAM found */ - if (dramsize > 0) { - *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 + - __builtin_ffs(dramsize >> 20) - 1; - } else { - *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */ - } - - *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */ -#else /* CONFIG_SYS_RAMBOOT */ - - /* retrieve size of memory connected to SDRAM CS0 */ - dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF; - if (dramsize >= 0x13) { - dramsize = (1 << (dramsize - 0x13)) << 20; - } else { - dramsize = 0; - } - - /* retrieve size of memory connected to SDRAM CS1 */ - dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF; - if (dramsize2 >= 0x13) { - dramsize2 = (1 << (dramsize2 - 0x13)) << 20; - } else { - dramsize2 = 0; - } - -#endif /* CONFIG_SYS_RAMBOOT */ - - /* - * On MPC5200B we need to set the special configuration delay in the - * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM - * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190: - * - * "The SDelay should be written to a value of 0x00000004. It is - * required to account for changes caused by normal wafer processing - * parameters." - */ - svr = get_svr(); - pvr = get_pvr(); - if ((SVR_MJREV(svr) >= 2) && - (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) { - - *(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04; - __asm__ volatile ("sync"); - } - -/* return dramsize + dramsize2; */ - return dramsize; -} - -int checkboard (void) -{ - puts ("Board: HMI1001\n"); - return 0; -} - -#ifdef CONFIG_PREBOOT - -static uchar kbd_magic_prefix[] = "key_magic"; -static uchar kbd_command_prefix[] = "key_cmd"; - -#define S1_ROT 0xf0 -#define S2_Q 0x40 -#define S2_M 0x20 - -struct kbd_data_t { - char s1; - char s2; -}; - -struct kbd_data_t* get_keys (struct kbd_data_t *kbd_data) -{ - kbd_data->s1 = *((volatile uchar*)(CONFIG_SYS_STATUS1_BASE)); - kbd_data->s2 = *((volatile uchar*)(CONFIG_SYS_STATUS2_BASE)); - - return kbd_data; -} - -static int compare_magic (const struct kbd_data_t *kbd_data, char *str) -{ - char s1 = str[0]; - char s2; - - if (s1 >= '0' && s1 <= '9') - s1 -= '0'; - else if (s1 >= 'a' && s1 <= 'f') - s1 = s1 - 'a' + 10; - else if (s1 >= 'A' && s1 <= 'F') - s1 = s1 - 'A' + 10; - else - return -1; - - if (((S1_ROT & kbd_data->s1) >> 4) != s1) - return -1; - - s2 = (S2_Q | S2_M) & kbd_data->s2; - - switch (str[1]) { - case 'q': - case 'Q': - if (s2 == S2_Q) - return -1; - break; - case 'm': - case 'M': - if (s2 == S2_M) - return -1; - break; - case '\0': - if (s2 == (S2_Q | S2_M)) - return 0; - default: - return -1; - } - - if (str[2]) - return -1; - - return 0; -} - -static char *key_match (const struct kbd_data_t *kbd_data) -{ - char magic[sizeof (kbd_magic_prefix) + 1]; - char *suffix; - char *kbd_magic_keys; - - /* - * The following string defines the characters that can be appended - * to "key_magic" to form the names of environment variables that - * hold "magic" key codes, i. e. such key codes that can cause - * pre-boot actions. If the string is empty (""), then only - * "key_magic" is checked (old behaviour); the string "125" causes - * checks for "key_magic1", "key_magic2" and "key_magic5", etc. - */ - if ((kbd_magic_keys = getenv ("magic_keys")) == NULL) - kbd_magic_keys = ""; - - /* loop over all magic keys; - * use '\0' suffix in case of empty string - */ - for (suffix = kbd_magic_keys; *suffix || - suffix == kbd_magic_keys; ++suffix) { - sprintf (magic, "%s%c", kbd_magic_prefix, *suffix); - - if (compare_magic(kbd_data, getenv(magic)) == 0) { - char cmd_name[sizeof (kbd_command_prefix) + 1]; - char *cmd; - - sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix); - cmd = getenv (cmd_name); - - return (cmd); - } - } - - return (NULL); -} - -#endif /* CONFIG_PREBOOT */ - -int misc_init_r (void) -{ -#ifdef CONFIG_PREBOOT - struct kbd_data_t kbd_data; - /* Decode keys */ - char *str = strdup (key_match (get_keys (&kbd_data))); - /* Set or delete definition */ - setenv ("preboot", str); - free (str); -#endif /* CONFIG_PREBOOT */ - - return 0; -} - -int board_early_init_r (void) -{ - *(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */ - *(vu_long *)MPC5XXX_BOOTCS_START = - *(vu_long *)MPC5XXX_CS0_START = START_REG(CONFIG_SYS_FLASH_BASE); - *(vu_long *)MPC5XXX_BOOTCS_STOP = - *(vu_long *)MPC5XXX_CS0_STOP = STOP_REG(CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_SIZE); - return 0; -} -#ifdef CONFIG_PCI -static struct pci_controller hose; - -extern void pci_mpc5xxx_init(struct pci_controller *); - -void pci_init_board(void) -{ - pci_mpc5xxx_init(&hose); -} -#endif diff --git a/board/manroland/mucmc52/Kconfig b/board/manroland/mucmc52/Kconfig deleted file mode 100644 index a033610cbf..0000000000 --- a/board/manroland/mucmc52/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_MUCMC52 - -config SYS_BOARD - default "mucmc52" - -config SYS_VENDOR - default "manroland" - -config SYS_CONFIG_NAME - default "mucmc52" - -endif diff --git a/board/manroland/mucmc52/MAINTAINERS b/board/manroland/mucmc52/MAINTAINERS deleted file mode 100644 index 45a276408b..0000000000 --- a/board/manroland/mucmc52/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -MUCMC52 BOARD -M: Heiko Schocher -S: Maintained -F: board/manroland/mucmc52/ -F: include/configs/mucmc52.h -F: configs/mucmc52_defconfig diff --git a/board/manroland/mucmc52/Makefile b/board/manroland/mucmc52/Makefile deleted file mode 100644 index 927fc3250a..0000000000 --- a/board/manroland/mucmc52/Makefile +++ /dev/null @@ -1,11 +0,0 @@ -# -# (C) Copyright 2008 -# Heiko Schocher, DENX Software Engineering, hs@denx.de. -# -# (C) Copyright 2003-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := mucmc52.o diff --git a/board/manroland/mucmc52/mucmc52.c b/board/manroland/mucmc52/mucmc52.c deleted file mode 100644 index c8ed5b73f4..0000000000 --- a/board/manroland/mucmc52/mucmc52.c +++ /dev/null @@ -1,394 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004 - * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com. - * - * (C) Copyright 2004 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * (C) Copyright 2008 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#include - -#ifndef CONFIG_SYS_RAMBOOT -static void sdram_start (int hi_addr) -{ - long hi_addr_bit = hi_addr ? 0x01000000 : 0; - - /* unlock mode register */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CTRL, - (SDRAM_CONTROL | 0x80000000 | hi_addr_bit)); - __asm__ volatile ("sync"); - - /* precharge all banks */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CTRL, - (SDRAM_CONTROL | 0x80000002 | hi_addr_bit)); - __asm__ volatile ("sync"); - -#if SDRAM_DDR - /* set mode register: extended mode */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_MODE, (SDRAM_EMODE)); - __asm__ volatile ("sync"); - - /* set mode register: reset DLL */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_MODE, - (SDRAM_MODE | 0x04000000)); - __asm__ volatile ("sync"); -#endif - - /* precharge all banks */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CTRL, - (SDRAM_CONTROL | 0x80000002 | hi_addr_bit)); - __asm__ volatile ("sync"); - - /* auto refresh */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CTRL, - (SDRAM_CONTROL | 0x80000004 | hi_addr_bit)); - __asm__ volatile ("sync"); - - /* set mode register */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_MODE, (SDRAM_MODE)); - __asm__ volatile ("sync"); - - /* normal operation */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CTRL, - (SDRAM_CONTROL | hi_addr_bit)); - __asm__ volatile ("sync"); -} -#endif - -/* - * ATTENTION: Although partially referenced initdram does NOT make real use - * use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE - * is something else than 0x00000000. - */ - -phys_size_t initdram (int board_type) -{ - ulong dramsize = 0; - ulong dramsize2 = 0; - uint svr, pvr; - -#ifndef CONFIG_SYS_RAMBOOT - ulong test1, test2; - - /* setup SDRAM chip selects */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS0CFG, 0x0000001c); /* 512MB at 0x0 */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS1CFG, 0x80000000);/* disabled */ - __asm__ volatile ("sync"); - - /* setup config registers */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CONFIG1, SDRAM_CONFIG1); - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CONFIG2, SDRAM_CONFIG2); - __asm__ volatile ("sync"); - -#if SDRAM_DDR - /* set tap delay */ - out_be32 ((unsigned __iomem *)MPC5XXX_CDM_PORCFG, SDRAM_TAPDELAY); - __asm__ volatile ("sync"); -#endif - - /* find RAM size using SDRAM CS0 only */ - sdram_start (0); - test1 = get_ram_size ((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000); - sdram_start(1); - test2 = get_ram_size ((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000); - if (test1 > test2) { - sdram_start (0); - dramsize = test1; - } else { - dramsize = test2; - } - - /* memory smaller than 1MB is impossible */ - if (dramsize < (1 << 20)) { - dramsize = 0; - } - - /* set SDRAM CS0 size according to the amount of RAM found */ - if (dramsize > 0) { - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS0CFG, - (0x13 + __builtin_ffs(dramsize >> 20) - 1)); - } else { - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS0CFG, 0); /* disabled */ - } - - /* let SDRAM CS1 start right after CS0 */ - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS1CFG, (dramsize + 0x0000001c));/*512MB*/ - - /* find RAM size using SDRAM CS1 only */ - if (!dramsize) - sdram_start (0); - test2 = test1 = get_ram_size ((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x20000000); - if (!dramsize) { - sdram_start (1); - test2 = get_ram_size ((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x20000000); - } - if (test1 > test2) { - sdram_start (0); - dramsize2 = test1; - } else { - dramsize2 = test2; - } - - /* memory smaller than 1MB is impossible */ - if (dramsize2 < (1 << 20)) { - dramsize2 = 0; - } - - /* set SDRAM CS1 size according to the amount of RAM found */ - if (dramsize2 > 0) { - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS1CFG, - (dramsize | (0x13 + __builtin_ffs(dramsize2 >> 20) - 1))); - } else { - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS1CFG, dramsize); /* disabled */ - } - -#else /* CONFIG_SYS_RAMBOOT */ - - /* retrieve size of memory connected to SDRAM CS0 */ - dramsize = in_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS0CFG) & 0xFF; - if (dramsize >= 0x13) { - dramsize = (1 << (dramsize - 0x13)) << 20; - } else { - dramsize = 0; - } - - /* retrieve size of memory connected to SDRAM CS1 */ - dramsize2 = in_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS1CFG) & 0xFF; - if (dramsize2 >= 0x13) { - dramsize2 = (1 << (dramsize2 - 0x13)) << 20; - } else { - dramsize2 = 0; - } - -#endif /* CONFIG_SYS_RAMBOOT */ - - /* - * On MPC5200B we need to set the special configuration delay in the - * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM - * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190: - * - * "The SDelay should be written to a value of 0x00000004. It is - * required to account for changes caused by normal wafer processing - * parameters." - */ - svr = get_svr(); - pvr = get_pvr(); - if ((SVR_MJREV(svr) >= 2) && - (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) { - - out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_SDELAY, 0x04); - __asm__ volatile ("sync"); - } - - return dramsize + dramsize2; -} - -int checkboard (void) -{ - puts ("Board: MUC.MC-52 HW WDT "); -#if defined(CONFIG_HW_WATCHDOG) - puts ("enabled\n"); -#else - puts ("disabled\n"); -#endif - return 0; -} - -#ifdef CONFIG_PREBOOT - -static uchar kbd_magic_prefix[] = "key_magic"; -static uchar kbd_command_prefix[] = "key_cmd"; - -#define S1_ROT 0xf0 -#define S2_Q 0x40 -#define S2_M 0x20 - -struct kbd_data_t { - char s1; - char s2; -}; - -struct kbd_data_t* get_keys (struct kbd_data_t *kbd_data) -{ - kbd_data->s1 = in_8 ((volatile uchar*)CONFIG_SYS_STATUS1_BASE); - kbd_data->s2 = in_8 ((volatile uchar*)CONFIG_SYS_STATUS2_BASE); - - return kbd_data; -} - -static int compare_magic (const struct kbd_data_t *kbd_data, char *str) -{ - char s1 = str[0]; - char s2; - - if (s1 >= '0' && s1 <= '9') - s1 -= '0'; - else if (s1 >= 'a' && s1 <= 'f') - s1 = s1 - 'a' + 10; - else if (s1 >= 'A' && s1 <= 'F') - s1 = s1 - 'A' + 10; - else - return -1; - - if (((S1_ROT & kbd_data->s1) >> 4) != s1) - return -1; - - s2 = (S2_Q | S2_M) & kbd_data->s2; - - switch (str[1]) { - case 'q': - case 'Q': - if (s2 == S2_Q) - return -1; - break; - case 'm': - case 'M': - if (s2 == S2_M) - return -1; - break; - case '\0': - if (s2 == (S2_Q | S2_M)) - return 0; - default: - return -1; - } - - if (str[2]) - return -1; - - return 0; -} - -static char *key_match (const struct kbd_data_t *kbd_data) -{ - char magic[sizeof (kbd_magic_prefix) + 1]; - char *suffix; - char *kbd_magic_keys; - - /* - * The following string defines the characters that can be appended - * to "key_magic" to form the names of environment variables that - * hold "magic" key codes, i. e. such key codes that can cause - * pre-boot actions. If the string is empty (""), then only - * "key_magic" is checked (old behaviour); the string "125" causes - * checks for "key_magic1", "key_magic2" and "key_magic5", etc. - */ - if ((kbd_magic_keys = getenv ("magic_keys")) == NULL) - kbd_magic_keys = ""; - - /* loop over all magic keys; - * use '\0' suffix in case of empty string - */ - for (suffix = kbd_magic_keys; *suffix || - suffix == kbd_magic_keys; ++suffix) { - sprintf (magic, "%s%c", kbd_magic_prefix, *suffix); - - if (compare_magic(kbd_data, getenv(magic)) == 0) { - char cmd_name[sizeof (kbd_command_prefix) + 1]; - char *cmd; - - sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix); - cmd = getenv (cmd_name); - - return (cmd); - } - } - - return (NULL); -} - -#endif /* CONFIG_PREBOOT */ - -int misc_init_r (void) -{ -#ifdef CONFIG_PREBOOT - struct kbd_data_t kbd_data; - /* Decode keys */ - char *str = strdup (key_match (get_keys (&kbd_data))); - /* Set or delete definition */ - setenv ("preboot", str); - free (str); -#endif /* CONFIG_PREBOOT */ - - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x38), ' '); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x39), ' '); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3A), ' '); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3B), ' '); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3C), ' '); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3D), ' '); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3E), ' '); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3F), ' '); - - return 0; -} - -int board_early_init_r (void) -{ - out_be32 ((unsigned __iomem *)MPC5XXX_BOOTCS_CFG, in_be32 ((unsigned __iomem *)MPC5XXX_BOOTCS_CFG) & ~0x1); - out_be32 ((unsigned __iomem *)MPC5XXX_BOOTCS_START, START_REG(CONFIG_SYS_FLASH_BASE)); - out_be32 ((unsigned __iomem *)MPC5XXX_CS0_START, START_REG(CONFIG_SYS_FLASH_BASE)); - out_be32 ((unsigned __iomem *)MPC5XXX_BOOTCS_STOP, - STOP_REG(CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_SIZE)); - out_be32 ((unsigned __iomem *)MPC5XXX_CS0_STOP, - STOP_REG(CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_SIZE)); - return 0; -} - -int last_stage_init (void) -{ - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x38), 'M'); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x39), 'U'); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3A), 'C'); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3B), '.'); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3C), 'M'); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3D), 'C'); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3E), '5'); - out_8 ((volatile uchar *)(CONFIG_SYS_DISPLAY_BASE + 0x3F), '2'); - - return 0; -} - -#if defined(CONFIG_HW_WATCHDOG) -#define GPT_OUT_0 0x00000027 -#define GPT_OUT_1 0x00000037 -void hw_watchdog_reset (void) -{ - /* Trigger HW Watchdog with TIMER_0 */ - out_be32 ((unsigned __iomem *)MPC5XXX_GPT0_ENABLE, GPT_OUT_1); - out_be32 ((unsigned __iomem *)MPC5XXX_GPT0_ENABLE, GPT_OUT_0); -} -#endif - -#ifdef CONFIG_PCI -static struct pci_controller hose; - -extern void pci_mpc5xxx_init (struct pci_controller *); - -void pci_init_board (void) -{ - pci_mpc5xxx_init (&hose); -} -#endif - -#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) -int ft_board_setup(void *blob, bd_t *bd) -{ - ft_cpu_setup(blob, bd); - - return 0; -} -#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/board/manroland/uc100/Kconfig b/board/manroland/uc100/Kconfig deleted file mode 100644 index 08f681b0a9..0000000000 --- a/board/manroland/uc100/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_UC100 - -config SYS_BOARD - default "uc100" - -config SYS_VENDOR - default "manroland" - -config SYS_CONFIG_NAME - default "uc100" - -endif diff --git a/board/manroland/uc100/MAINTAINERS b/board/manroland/uc100/MAINTAINERS deleted file mode 100644 index 260471ce92..0000000000 --- a/board/manroland/uc100/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -UC100 BOARD -M: Stefan Roese -S: Maintained -F: board/manroland/uc100/ -F: include/configs/uc100.h -F: configs/uc100_defconfig diff --git a/board/manroland/uc100/Makefile b/board/manroland/uc100/Makefile deleted file mode 100644 index 8e69c52de1..0000000000 --- a/board/manroland/uc100/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = uc100.o pcmcia.o diff --git a/board/manroland/uc100/pcmcia.c b/board/manroland/uc100/pcmcia.c deleted file mode 100644 index db3821a5e4..0000000000 --- a/board/manroland/uc100/pcmcia.c +++ /dev/null @@ -1,192 +0,0 @@ -#include -#include -#include - -#undef CONFIG_PCMCIA - -#if defined(CONFIG_CMD_PCMCIA) -#define CONFIG_PCMCIA -#endif - -#if (defined(CONFIG_CMD_IDE)) && defined(CONFIG_IDE_8xx_PCCARD) -#define CONFIG_PCMCIA -#endif - -#ifdef CONFIG_PCMCIA - -#define PCMCIA_BOARD_MSG "UC100" - -/* - * Remark: don't turn off OE "__MY_PCMCIA_GCRX_CXOE" on UC100 board. - * This leads to board-hangup! (sr, 8 Dez. 2004) - */ -static void cfg_ports (void) -{ - volatile immap_t *immap; - - immap = (immap_t *)CONFIG_SYS_IMMR; - - /* - * Configure Port A for MAX1602 PC-Card Power-Interface Switch - */ - immap->im_ioport.iop_padat &= ~0x8000; /* set port x output to low */ - immap->im_ioport.iop_padir |= 0x8000; /* enable port x as output */ - - debug ("Set Port A: PAR: %08x DIR: %08x DAT: %08x\n", - immap->im_ioport.iop_papar, immap->im_ioport.iop_padir, - immap->im_ioport.iop_padat); -} - -int pcmcia_hardware_enable(int slot) -{ - volatile immap_t *immap; - volatile pcmconf8xx_t *pcmp; - volatile sysconf8xx_t *sysp; - uint reg, mask; - - debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot); - - udelay(10000); - - immap = (immap_t *)CONFIG_SYS_IMMR; - sysp = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf)); - pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia)); - - /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */ - cfg_ports (); - - /* - * Configure SIUMCR to enable PCMCIA port B - * (VFLS[0:1] are not used for debugging, we connect FRZ# instead) - */ - sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */ - - /* clear interrupt state, and disable interrupts */ - pcmp->pcmc_pscr = PCMCIA_MASK(_slot_); - pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_); - - /* - * Disable interrupts, DMA, and PCMCIA buffers - * (isolate the interface) and assert RESET signal - */ - debug ("Disable PCMCIA buffers and assert RESET\n"); - reg = 0; - reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ - PCMCIA_PGCRX(_slot_) = reg; - udelay(500); - - /* - * Make sure there is a card in the slot, then configure the interface. - */ - udelay(10000); - debug ("[%d] %s: PIPR(%p)=0x%x\n", - __LINE__,__FUNCTION__, - &(pcmp->pcmc_pipr),pcmp->pcmc_pipr); - if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) { - printf (" No Card found\n"); - return (1); - } - - /* - * Power On. - */ - mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot); - reg = pcmp->pcmc_pipr; - debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", - reg, - (reg&PCMCIA_VS1(slot))?"n":"ff", - (reg&PCMCIA_VS2(slot))?"n":"ff"); - - if ((reg & mask) == mask) - puts (" 5.0V card found: "); - else - puts (" 3.3V card found: "); - - /* switch VCC on */ - immap->im_ioport.iop_padat |= 0x8000; /* power enable 3.3V */ - - udelay(10000); - - debug ("Enable PCMCIA buffers and stop RESET\n"); - reg = PCMCIA_PGCRX(_slot_); - reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ - reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */ - PCMCIA_PGCRX(_slot_) = reg; - - udelay(250000); /* some cards need >150 ms to come up :-( */ - - debug ("# hardware_enable done\n"); - - return (0); -} - - -#if defined(CONFIG_CMD_PCMCIA) -int pcmcia_hardware_disable(int slot) -{ - volatile immap_t *immap; - volatile cpm8xx_t *cp; - volatile pcmconf8xx_t *pcmp; - u_long reg; - - debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot); - - immap = (immap_t *)CONFIG_SYS_IMMR; - pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia)); - - /* switch VCC off */ - immap->im_ioport.iop_padat &= ~0x8000; /* power disable 3.3V */ - - /* Configure PCMCIA General Control Register */ - debug ("Disable PCMCIA buffers and assert RESET\n"); - reg = 0; - reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ - PCMCIA_PGCRX(_slot_) = reg; - - udelay(10000); - - return (0); -} -#endif - - -int pcmcia_voltage_set(int slot, int vcc, int vpp) -{ - u_long reg; - - debug ("voltage_set: " - PCMCIA_BOARD_MSG - " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n", - 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10); - - /* - * Disable PCMCIA buffers (isolate the interface) - * and assert RESET signal - */ - debug ("Disable PCMCIA buffers and assert RESET\n"); - reg = PCMCIA_PGCRX(_slot_); - reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ - PCMCIA_PGCRX(_slot_) = reg; - udelay(500); - - /* - * Configure Port C pins for - * 5 Volts Enable and 3 Volts enable, - * Turn all power pins to Hi-Z - */ - debug ("PCMCIA power OFF\n"); - cfg_ports (); /* Enables switch, but all in Hi-Z */ - - debug ("Enable PCMCIA buffers and stop RESET\n"); - reg = PCMCIA_PGCRX(_slot_); - reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ - reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */ - PCMCIA_PGCRX(_slot_) = reg; - udelay(500); - - debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", - slot+'A'); - return (0); -} - -#endif /* CONFIG_PCMCIA */ diff --git a/board/manroland/uc100/uc100.c b/board/manroland/uc100/uc100.c deleted file mode 100644 index 31f08dda7b..0000000000 --- a/board/manroland/uc100/uc100.c +++ /dev/null @@ -1,254 +0,0 @@ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#if 0 -#define DEBUG -#endif - -#include -#include -#include -#include - -int fec8xx_miiphy_write(char *devname, unsigned char addr, - unsigned char reg, unsigned short value); - -/*********************************************************************/ -/* UPMA Pre Initilization Table by WV (Miron MT48LC16M16A2-7E B) */ -/*********************************************************************/ -const uint sdram_init_upm_table[] = { - /* SDRAM Initialisation Sequence (offset 0 in UPMA RAM) WV */ - /* NOP - Precharge - AutoRefr - NOP - NOP */ - /* NOP - AutoRefr - NOP */ - /* NOP - NOP - LoadModeR - NOP - Active */ - /* Position of Single Read */ - 0x0ffffc04, 0x0ff77c04, 0x0ff5fc04, 0x0ffffc04, 0x0ffffc04, - 0x0ffffc04, 0x0ff5fc04, 0x0ffffc04, - - /* Burst Read. (offset 8 in UPMA RAM) */ - /* Cycle lent for Initialisation WV */ - 0x0ffffc04, 0x0ffffc34, 0x0f057c34, 0x0ffffc30, 0x1ff7fc05, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - - /* Single Write. (offset 18 in UPMA RAM) */ - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - - /* Burst Write. (offset 20 in UPMA RAM) */ - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - - /* Refresh (offset 30 in UPMA RAM) */ - 0x0FF77C04, 0x0FFFFC04, 0x0FF5FC84, 0x0FFFFC04, 0x0FFFFC04, - 0x0FFFFC84, 0x1FFFFC05, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, - - /* Exception. (offset 3c in UPMA RAM) */ - 0x7FFFFC05, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, -}; - -/*********************************************************************/ -/* UPMA initilization table. */ -/*********************************************************************/ -const uint sdram_upm_table[] = { - /* single read. (offset 0 in UPMA RAM) */ - 0x0F07FC04, 0x0FFFFC04, 0x00BDFC04, 0x0FF77C00, 0x1FFFFC05, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, /* 0x05-0x07 new WV */ - - /* Burst Read. (offset 8 in UPMA RAM) */ - 0x0F07FC04, 0x0FFFFC04, 0x00BDFC04, 0x00FFFC00, 0x00FFFC00, - 0x00FFFC00, 0x0FF77C00, 0x1FFFFC05, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - - /* Single Write. (offset 18 in UPMA RAM) */ - 0x0F07FC04, 0x0FFFFC00, 0x00BD7C04, 0x0FFFFC04, 0x0FF77C04, - 0x1FFFFC05, 0xFFFFFFFF, 0xFFFFFFFF, - - /* Burst Write. (offset 20 in UPMA RAM) */ - 0x0F07FC04, 0x0FFFFC00, 0x00BD7C00, 0x00FFFC00, 0x00FFFC00, - 0x00FFFC04, 0x0FFFFC04, 0x0FF77C04, 0x1FFFFC05, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - - /* Refresh (offset 30 in UPMA RAM) */ - 0x0FF77C04, 0x0FFFFC04, 0x0FF5FC84, 0x0FFFFC04, 0x0FFFFC04, - 0x0FFFFC84, 0x1FFFFC05, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, - - /* Exception. (offset 3c in UPMA RAM) */ - 0x7FFFFC05, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, /* 0x3C new WV */ -}; - -/*********************************************************************/ -/* UPMB initilization table. */ -/*********************************************************************/ -const uint mpm_upm_table[] = { - /* single read. (offset 0 in upm RAM) */ - 0x8FF00004, 0x0FF00004, 0x0FF81004, 0x1FF00001, - 0x1FF00001, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - - /* burst read. (Offset 8 in upm RAM) */ - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - - /* single write. (Offset 0x18 in upm RAM) */ - 0x8FF00004, 0x0FF00004, 0x0FF81004, 0x0FF00004, - 0x0FF00004, 0x1FF00001, 0xFFFFFFFF, 0xFFFFFFFF, - - /* burst write. (Offset 0x20 in upm RAM) */ - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - - /* Refresh cycle, offset 0x30 */ - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - - /* Exception, 0ffset 0x3C */ - 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, -}; - - -int board_switch(void) -{ - volatile pcmconf8xx_t *pcmp; - - pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia)); - - return ((pcmp->pcmc_pipr >> 24) & 0xf); -} - - -/* - * Check Board Identity: - */ -int checkboard (void) -{ - char str[64]; - int i = getenv_f("serial#", str, sizeof(str)); - - puts ("Board: "); - - if (i == -1) { - puts ("### No HW ID - assuming UC100"); - } else { - puts(str); - } - - printf (" (SWITCH=%1X)\n", board_switch()); - - return 0; -} - - -/* - * Initialize SDRAM - */ -phys_size_t initdram (int board_type) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8xx_t *memctl = &immap->im_memctl; - - /*---------------------------------------------------------------------*/ - /* Initialize the UPMA/UPMB registers with the appropriate table. */ - /*---------------------------------------------------------------------*/ - upmconfig (UPMA, (uint *) sdram_init_upm_table, - sizeof (sdram_init_upm_table) / sizeof (uint)); - upmconfig (UPMB, (uint *) mpm_upm_table, - sizeof (mpm_upm_table) / sizeof (uint)); - - /*---------------------------------------------------------------------*/ - /* Memory Periodic Timer Prescaler: divide by 16 */ - /*---------------------------------------------------------------------*/ - memctl->memc_mptpr = 0x0200; /* Divide by 32 WV */ - - memctl->memc_mamr = CONFIG_SYS_MAMR_VAL & 0xFF7FFFFF; /* Bit 8 := "0" Kein Refresh WV */ - memctl->memc_mbmr = CONFIG_SYS_MBMR_VAL; - - /*---------------------------------------------------------------------*/ - /* Initialize the Memory Controller registers, MPTPR, Chip Select 1 */ - /* for SDRAM */ - /* */ - /* NOTE: The refresh rate in MAMR reg is set according to the lowest */ - /* clock rate (16.67MHz) to allow proper operation for all ADS */ - /* clock frequencies. */ - /*---------------------------------------------------------------------*/ - memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM; - memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM; - - /*-------------------------------------------------------------------*/ - /* Wait at least 200 usec for DRAM to stabilize, this magic number */ - /* obtained from the init code. */ - /*-------------------------------------------------------------------*/ - udelay(200); - - memctl->memc_mamr = (memctl->memc_mamr | 0x04) & ~0x08; - - memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM; - memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM; - - /*---------------------------------------------------------------------*/ - /* run MRS command in location 5-8 of UPMB. */ - /*---------------------------------------------------------------------*/ - memctl->memc_mar = 0x88; - /* RUN UPMA on CS1 1-time from UPMA addr 0x05 */ - - memctl->memc_mcr = 0x80002100; - /* RUN UPMA on CS1 1-time from UPMA addr 0x00 WV */ - - udelay(200); - - /*---------------------------------------------------------------------*/ - /* Initialisation for normal access WV */ - /*---------------------------------------------------------------------*/ - - /*---------------------------------------------------------------------*/ - /* Initialize the UPMA register with the appropriate table. */ - /*---------------------------------------------------------------------*/ - upmconfig (UPMA, (uint *) sdram_upm_table, - sizeof (sdram_upm_table) / sizeof (uint)); - - /*---------------------------------------------------------------------*/ - /* rerstore MBMR value (4-beat refresh burst.) */ - /*---------------------------------------------------------------------*/ - memctl->memc_mamr = CONFIG_SYS_MAMR_VAL | 0x00800000; /* Bit 8 := "1" Refresh Enable WV */ - - udelay(200); - - return (64 * 1024 * 1024); /* fixed setup for 64MBytes! */ -} - - -int misc_init_r (void) -{ - uchar val; - - /* - * Make sure that RTC has clock output enabled (triggers watchdog!) - */ - val = i2c_reg_read (CONFIG_SYS_I2C_RTC_ADDR, 0x0D); - val |= 0x80; - i2c_reg_write (CONFIG_SYS_I2C_RTC_ADDR, 0x0D, val); - - /* - * Configure PHY to setup LED's correctly and use 100MBit, FD - */ - mii_init(); - - /* disable auto-negotiation, 100mbit, full-duplex */ - fec8xx_miiphy_write(NULL, 0, MII_BMCR, 0x2100); - - /* set LED's to Link, Transmit, Receive */ - fec8xx_miiphy_write(NULL, 0, MII_NWAYTEST, 0x4122); - - return 0; -} diff --git a/board/manroland/uc101/Kconfig b/board/manroland/uc101/Kconfig deleted file mode 100644 index c285b22f1b..0000000000 --- a/board/manroland/uc101/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_UC101 - -config SYS_BOARD - default "uc101" - -config SYS_VENDOR - default "manroland" - -config SYS_CONFIG_NAME - default "uc101" - -endif diff --git a/board/manroland/uc101/MAINTAINERS b/board/manroland/uc101/MAINTAINERS deleted file mode 100644 index 0fc7b85838..0000000000 --- a/board/manroland/uc101/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -UC101 BOARD -M: Heiko Schocher -S: Maintained -F: board/manroland/uc101/ -F: include/configs/uc101.h -F: configs/uc101_defconfig diff --git a/board/manroland/uc101/Makefile b/board/manroland/uc101/Makefile deleted file mode 100644 index 9289d915d9..0000000000 --- a/board/manroland/uc101/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2003-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := uc101.o diff --git a/board/manroland/uc101/uc101.c b/board/manroland/uc101/uc101.c deleted file mode 100644 index e794c4645e..0000000000 --- a/board/manroland/uc101/uc101.c +++ /dev/null @@ -1,367 +0,0 @@ -/* - * (C) Copyright 2006 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004 - * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com. - * - * (C) Copyright 2004 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include - -/* some SIMPLE GPIO Pins */ -#define GPIO_USB_8 (31-12) -#define GPIO_USB_7 (31-13) -#define GPIO_USB_6 (31-14) -#define GPIO_USB_0 (31-15) -#define GPIO_PSC3_7 (31-18) -#define GPIO_PSC3_6 (31-19) -#define GPIO_PSC3_1 (31-22) -#define GPIO_PSC3_0 (31-23) - -/* some simple Interrupt GPIO Pins */ -#define GPIO_PSC3_8 2 -#define GPIO_USB1_9 3 - -#define GPT_OUT_0 0x00000027 -#define GPT_OUT_1 0x00000037 -#define GPT_DISABLE 0x00000000 /* GPT pin disabled */ - -#define GP_SIMP_ENABLE_O(n, v) {pgpio->simple_dvo |= (v << n); \ - pgpio->simple_ddr |= (1 << n); \ - pgpio->simple_gpioe |= (1 << n); \ - } - -#define GP_SIMP_ENABLE_I(n) { pgpio->simple_ddr |= ~(1 << n); \ - pgpio->simple_gpioe |= (1 << n); \ - } - -#define GP_SIMP_SET_O(n, v) (pgpio->simple_dvo = v ? \ - (pgpio->simple_dvo | (1 << n)) : \ - (pgpio->simple_dvo & ~(1 << n)) ) - -#define GP_SIMP_GET_O(n) ((pgpio->simple_dvo >> n) & 1) -#define GP_SIMP_GET_I(n) ((pgpio->simple_ival >> n) & 1) - -#define GP_SINT_SET_O(n, v) (pgpio->sint_dvo = v ? \ - (pgpio->sint_dvo | (1 << n)) : \ - (pgpio->sint_dvo & ~(1 << n)) ) - -#define GP_SINT_ENABLE_O(n, v) {pgpio->sint_ode &= ~(1 << n); \ - pgpio->sint_ddr |= (1 << n); \ - GP_SINT_SET_O(n, v); \ - pgpio->sint_gpioe |= (1 << n); \ - } - -#define GP_SINT_ENABLE_I(n) { pgpio->sint_ddr |= ~(1 << n); \ - pgpio->sint_gpioe |= (1 << n); \ - } - -#define GP_SINT_GET_O(n) ((pgpio->sint_ival >> n) & 1) -#define GP_SINT_GET_I(n) ((pgpio-ntt_ival >> n) & 1) - -#define GP_TIMER_ENABLE_O(n, v) ( \ - ((volatile struct mpc5xxx_gpt *)(MPC5XXX_GPT + n))->emsr = v ? \ - GPT_OUT_1 : \ - GPT_OUT_0 ) - -#define GP_TIMER_SET_O(n, v) GP_TIMER_ENABLE_O(n, v) - -#define GP_TIMER_GET_O(n, v) ( \ - (((volatile struct mpc5xxx_gpt *)(MPC5XXX_GPT + n))->emsr & 0x10) >> 4) - -#define GP_TIMER_GET_I(n, v) ( \ - (((volatile struct mpc5xxx_gpt *)(MPC5XXX_GPT + n))->sr & 0x100) >> 8) - -#ifndef CONFIG_SYS_RAMBOOT -static void sdram_start (int hi_addr) -{ - long hi_addr_bit = hi_addr ? 0x01000000 : 0; - - /* unlock mode register */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit; - __asm__ volatile ("sync"); - - /* precharge all banks */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit; - __asm__ volatile ("sync"); - -#if SDRAM_DDR - /* set mode register: extended mode */ - *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE; - __asm__ volatile ("sync"); - - /* set mode register: reset DLL */ - *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000; - __asm__ volatile ("sync"); -#endif - - /* precharge all banks */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit; - __asm__ volatile ("sync"); - - /* auto refresh */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit; - __asm__ volatile ("sync"); - - /* set mode register */ - *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE; - __asm__ volatile ("sync"); - - /* normal operation */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit; - __asm__ volatile ("sync"); -} -#endif - -/* - * ATTENTION: Although partially referenced initdram does NOT make real use - * use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE - * is something else than 0x00000000. - */ - -phys_size_t initdram (int board_type) -{ - ulong dramsize = 0; -#ifndef CONFIG_SYS_RAMBOOT - ulong test1, test2; - - /* setup SDRAM chip selects */ - *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001c; /* 512MB at 0x0 */ - *(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x40000000; /* disabled */ - __asm__ volatile ("sync"); - - /* setup config registers */ - *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1; - *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2; - __asm__ volatile ("sync"); - -#if SDRAM_DDR - /* set tap delay */ - *(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY; - __asm__ volatile ("sync"); -#endif - - /* find RAM size using SDRAM CS0 only */ - sdram_start(0); - test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000); - sdram_start(1); - test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000); - if (test1 > test2) { - sdram_start(0); - dramsize = test1; - } else { - dramsize = test2; - } - - /* memory smaller than 1MB is impossible */ - if (dramsize < (1 << 20)) { - dramsize = 0; - } - - /* set SDRAM CS0 size according to the amount of RAM found */ - if (dramsize > 0) { - *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 + - __builtin_ffs(dramsize >> 20) - 1; - } else { - *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */ - } - - *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */ -#else /* CONFIG_SYS_RAMBOOT */ - - /* retrieve size of memory connected to SDRAM CS0 */ - dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF; - if (dramsize >= 0x13) { - dramsize = (1 << (dramsize - 0x13)) << 20; - } else { - dramsize = 0; - } - - /* retrieve size of memory connected to SDRAM CS1 */ - dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF; - if (dramsize2 >= 0x13) { - dramsize2 = (1 << (dramsize2 - 0x13)) << 20; - } else { - dramsize2 = 0; - } - -#endif /* CONFIG_SYS_RAMBOOT */ - -/* return dramsize + dramsize2; */ - return dramsize; -} - -int checkboard (void) -{ - puts ("Board: MAN UC101\n"); - /* clear the Display */ - *(char *)(CONFIG_SYS_DISP_CWORD) = 0x80; - return 0; -} - -static void init_ports (void) -{ - volatile struct mpc5xxx_gpio *pgpio = - (struct mpc5xxx_gpio *)MPC5XXX_GPIO; - - GP_SIMP_ENABLE_I(GPIO_USB_8); /* HEX Bit 3 */ - GP_SIMP_ENABLE_I(GPIO_USB_7); /* HEX Bit 2 */ - GP_SIMP_ENABLE_I(GPIO_USB_6); /* HEX Bit 1 */ - GP_SIMP_ENABLE_I(GPIO_USB_0); /* HEX Bit 0 */ - GP_SIMP_ENABLE_I(GPIO_PSC3_0); /* Switch Menue A */ - GP_SIMP_ENABLE_I(GPIO_PSC3_1); /* Switch Menue B */ - GP_SIMP_ENABLE_I(GPIO_PSC3_6); /* Switch Cold_Warm */ - GP_SIMP_ENABLE_I(GPIO_PSC3_7); /* Switch Restart */ - GP_SINT_ENABLE_O(GPIO_PSC3_8, 0); /* LED H2 */ - GP_SINT_ENABLE_O(GPIO_USB1_9, 0); /* LED H3 */ - GP_TIMER_ENABLE_O(4, 0); /* LED H4 */ - GP_TIMER_ENABLE_O(5, 0); /* LED H5 */ - GP_TIMER_ENABLE_O(3, 0); /* LED HB */ - GP_TIMER_ENABLE_O(1, 0); /* RES_COLDSTART */ -} - -#ifdef CONFIG_PREBOOT - -static uchar kbd_magic_prefix[] = "key_magic"; -static uchar kbd_command_prefix[] = "key_cmd"; - -struct kbd_data_t { - char s1; -}; - -struct kbd_data_t* get_keys (struct kbd_data_t *kbd_data) -{ - volatile struct mpc5xxx_gpio *pgpio = - (struct mpc5xxx_gpio *)MPC5XXX_GPIO; - - kbd_data->s1 = GP_SIMP_GET_I(GPIO_USB_8) << 3 | \ - GP_SIMP_GET_I(GPIO_USB_7) << 2 | \ - GP_SIMP_GET_I(GPIO_USB_6) << 1 | \ - GP_SIMP_GET_I(GPIO_USB_0) << 0; - return kbd_data; -} - -static int compare_magic (const struct kbd_data_t *kbd_data, char *str) -{ - char s1 = str[0]; - - if (s1 >= '0' && s1 <= '9') - s1 -= '0'; - else if (s1 >= 'a' && s1 <= 'f') - s1 = s1 - 'a' + 10; - else if (s1 >= 'A' && s1 <= 'F') - s1 = s1 - 'A' + 10; - else - return -1; - - if (s1 != kbd_data->s1) return -1; - return 0; -} - -static char *key_match (const struct kbd_data_t *kbd_data) -{ - char magic[sizeof (kbd_magic_prefix) + 1]; - char *suffix; - char *kbd_magic_keys; - - /* - * The following string defines the characters that can be appended - * to "key_magic" to form the names of environment variables that - * hold "magic" key codes, i. e. such key codes that can cause - * pre-boot actions. If the string is empty (""), then only - * "key_magic" is checked (old behaviour); the string "125" causes - * checks for "key_magic1", "key_magic2" and "key_magic5", etc. - */ - if ((kbd_magic_keys = getenv ("magic_keys")) == NULL) - kbd_magic_keys = ""; - - /* loop over all magic keys; - * use '\0' suffix in case of empty string - */ - for (suffix = kbd_magic_keys; *suffix || - suffix == kbd_magic_keys; ++suffix) { - sprintf (magic, "%s%c", kbd_magic_prefix, *suffix); - - if (compare_magic(kbd_data, getenv(magic)) == 0) { - char cmd_name[sizeof (kbd_command_prefix) + 1]; - char *cmd; - - sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix); - cmd = getenv (cmd_name); - - return (cmd); - } - } - - return (NULL); -} - -#endif /* CONFIG_PREBOOT */ - -int misc_init_r (void) -{ - /* Init the I/O ports */ - init_ports (); - -#ifdef CONFIG_PREBOOT - struct kbd_data_t kbd_data; - /* Decode keys */ - char *str = strdup (key_match (get_keys (&kbd_data))); - /* Set or delete definition */ - setenv ("preboot", str); - free (str); -#endif /* CONFIG_PREBOOT */ - return 0; -} - -int board_early_init_r (void) -{ - *(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */ - *(vu_long *)MPC5XXX_BOOTCS_START = - *(vu_long *)MPC5XXX_CS0_START = START_REG(CONFIG_SYS_FLASH_BASE); - *(vu_long *)MPC5XXX_BOOTCS_STOP = - *(vu_long *)MPC5XXX_CS0_STOP = STOP_REG(CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_SIZE); - /* Interbus enable it here ?? */ - *(vu_long *)MPC5XXX_GPT6_ENABLE = GPT_OUT_1; - return 0; -} -#ifdef CONFIG_PCI -static struct pci_controller hose; - -extern void pci_mpc5xxx_init(struct pci_controller *); - -void pci_init_board(void) -{ - pci_mpc5xxx_init(&hose); -} -#endif - -#if defined(CONFIG_HW_WATCHDOG) -void hw_watchdog_reset(void) -{ - /* Trigger HW Watchdog with TIMER_0 */ - *(vu_long *)MPC5XXX_GPT0_ENABLE = GPT_OUT_1; - *(vu_long *)MPC5XXX_GPT0_ENABLE = GPT_OUT_0; -} -#endif - -#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) -int ft_board_setup(void *blob, bd_t *bd) -{ - ft_cpu_setup(blob, bd); - - return 0; -} -#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/configs/hmi1001_defconfig b/configs/hmi1001_defconfig deleted file mode 100644 index a351dbe65f..0000000000 --- a/configs/hmi1001_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_HMI1001=y diff --git a/configs/mucmc52_defconfig b/configs/mucmc52_defconfig deleted file mode 100644 index 1e4969516d..0000000000 --- a/configs/mucmc52_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MUCMC52=y diff --git a/configs/uc100_defconfig b/configs/uc100_defconfig deleted file mode 100644 index 76eeb11b8a..0000000000 --- a/configs/uc100_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_PPC=y -CONFIG_8xx=y -CONFIG_TARGET_UC100=y diff --git a/configs/uc101_defconfig b/configs/uc101_defconfig deleted file mode 100644 index b365bff2f0..0000000000 --- a/configs/uc101_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_UC101=y diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 3cf32e7ed2..8bd7056d13 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,6 +12,10 @@ The list should be sorted in reverse chronological order. Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +hmi1001 powerpc mpc5xxx - - +mucmc52 powerpc mpc5xxx - - Heiko Schocher +uc101 powerpc mpc5xxx - - Heiko Schocher +uc100 powerpc mpc8xx - - Stefan Roese FPS850L powerpc mpc8xx - - Wolfgang Denk FPS860L powerpc mpc8xx - - Wolfgang Denk NSCU powerpc mpc8xx - - diff --git a/drivers/net/mpc5xxx_fec.c b/drivers/net/mpc5xxx_fec.c index 1093ba59da..d9d6f4f28b 100644 --- a/drivers/net/mpc5xxx_fec.c +++ b/drivers/net/mpc5xxx_fec.c @@ -476,11 +476,6 @@ static int mpc5xxx_fec_init_phy(struct eth_device *dev, bd_t * bis) miiphy_write(dev->name, phyAddr, 0x0, 0x8000); udelay(1000); -#if defined(CONFIG_UC101) || defined(CONFIG_MUCMC52) - /* Set the LED configuration Register for the UC101 - and MUCMC52 Board */ - miiphy_write(dev->name, phyAddr, 0x14, 0x4122); -#endif if (fec->xcv_type == MII10) { /* * Force 10Base-T, FDX operation diff --git a/drivers/video/smiLynxEM.c b/drivers/video/smiLynxEM.c index 614bcb3c92..1880cccac2 100644 --- a/drivers/video/smiLynxEM.c +++ b/drivers/video/smiLynxEM.c @@ -131,9 +131,6 @@ static char SMI_PCR [] = { }; static char SMI_MCR[] = { 0x60, 0x01, 0x61, 0x00, -#ifdef CONFIG_HMI1001 - 0x62, 0x74, /* Memory type is not configured by pins on HMI1001 */ -#endif }; static char SMI_HCR[] = { diff --git a/include/configs/hmi1001.h b/include/configs/hmi1001.h deleted file mode 100644 index a1a88b5e33..0000000000 --- a/include/configs/hmi1001.h +++ /dev/null @@ -1,339 +0,0 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_HMI1001 1 /* HMI1001 board */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_BOARD_EARLY_INIT_R - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* Partitions */ -#define CONFIG_DOS_PARTITION - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DISPLAY -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_SNTP - - -#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ - -#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run net_nfs" - -#define CONFIG_MISC_INIT_R 1 - -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -/* - * RTC configuration - */ -#define CONFIG_RTC_PCF8563 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE 0xFF800000 - -#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ -#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max num of sects on one chip */ - -#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_CFI_AMD_RESET - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x4000 -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 -#define CONFIG_SYS_DISPLAY_BASE 0x80600000 -#define CONFIG_SYS_STATUS1_BASE 0x80600200 -#define CONFIG_SYS_STATUS2_BASE 0x80600300 - -/* Settings for XLB = 132 MHz */ -#define SDRAM_DDR 1 -#define SDRAM_MODE 0x018D0000 -#define SDRAM_EMODE 0x40090000 -#define SDRAM_CONTROL 0x714f0f00 -#define SDRAM_CONFIG1 0x73722930 -#define SDRAM_CONFIG2 0x47770000 -#define SDRAM_TAPDELAY 0x10000000 - -/* Use ON-Chip SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM - -/* preserve space for the post_word at end of on-chip SRAM */ -#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4) - -#ifdef CONFIG_POST -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE -#else -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE -#endif - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -#define CONFIG_PHY_ADDR 0x00 -#define CONFIG_MII 1 /* MII PHY management */ - -/* - * GPIO configuration - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x01051004 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* Enable an alternate, more extensive memory test */ -#define CONFIG_SYS_ALT_MEMTEST - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Enable loopw command. - */ -#define CONFIG_LOOPW - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x0004FB00 -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -/* 8Mbit SRAM @0x80100000 */ -#define CONFIG_SYS_CS1_START 0x80100000 -#define CONFIG_SYS_CS1_SIZE 0x00100000 -#define CONFIG_SYS_CS1_CFG 0x19B00 - -/* FRAM 32Kbyte @0x80700000 */ -#define CONFIG_SYS_CS2_START 0x80700000 -#define CONFIG_SYS_CS2_SIZE 0x00008000 -#define CONFIG_SYS_CS2_CFG 0x19800 - -/* Display H1, Status Inputs, EPLD @0x80600000 */ -#define CONFIG_SYS_CS3_START 0x80600000 -#define CONFIG_SYS_CS3_SIZE 0x00100000 -#define CONFIG_SYS_CS3_CFG 0x00019800 - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ - -#define CONFIG_IDE_PREINIT 1 - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#define CONFIG_ATAPI 1 - -#define CONFIG_VIDEO_SMI_LYNXEM -#define CONFIG_CFB_CONSOLE -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_VIDEO_LOGO - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_SYS_ISA_IO CONFIG_PCI_IO_BUS - -/*---------------------------------------------------------------------*/ -/* Display addresses */ -/*---------------------------------------------------------------------*/ - -#define CONFIG_PDSP188x -#define CONFIG_SYS_DISP_CHR_RAM (CONFIG_SYS_DISPLAY_BASE + 0x38) -#define CONFIG_SYS_DISP_CWORD (CONFIG_SYS_DISPLAY_BASE + 0x30) - -#endif /* __CONFIG_H */ diff --git a/include/configs/mucmc52.h b/include/configs/mucmc52.h deleted file mode 100644 index ff75ead295..0000000000 --- a/include/configs/mucmc52.h +++ /dev/null @@ -1,126 +0,0 @@ -/* - * (C) Copyright 2008-2009 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MUCMC52 1 /* MUCMC52 board */ -#define CONFIG_HOSTNAME mucmc52 - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#endif - -#include "manroland/common.h" -#include "manroland/mpc5200-common.h" - -#define CONFIG_LAST_STAGE_INIT -/* - * Serial console configuration - */ -#define CONFIG_BAUDRATE 38400 /* ... at 38400 bps */ - -#define CONFIG_CMD_PCI - -/* - * Flash configuration - */ -#define CONFIG_SYS_MAX_FLASH_SECT 67 - -/* - * Environment settings - */ -#define CONFIG_ENV_SECT_SIZE 0x20000 - -/* - * Memory map - */ -#define CONFIG_SYS_STATUS1_BASE 0x80600200 -#define CONFIG_SYS_STATUS2_BASE 0x80600300 -#define CONFIG_SYS_PMI_UNI_BASE 0x80800000 -#define CONFIG_SYS_PMI_BROAD_BASE 0x80810000 - -/* - * GPIO configuration - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x8D550644 - -#define CONFIG_SYS_MEMTEST_START 0x00100000 -#define CONFIG_SYS_MEMTEST_END 0x00f00000 - -#define CONFIG_SYS_LOAD_ADDR 0x100000 - -#define CONFIG_SYS_BOOTCS_CFG 0x0004FB00 - -/* 8Mbit SRAM @0x80100000 */ -#define CONFIG_SYS_CS1_SIZE 0x00100000 -#define CONFIG_SYS_CS1_CFG 0x00019B00 - -#define CONFIG_SYS_SRAM_SIZE CONFIG_SYS_CS1_SIZE - -/* FRAM 32Kbyte @0x80700000 */ -#define CONFIG_SYS_CS2_START 0x80700000 -#define CONFIG_SYS_CS2_SIZE 0x00008000 -#define CONFIG_SYS_CS2_CFG 0x00019800 - -/* Display H1, Status Inputs, EPLD @0x80600000 */ -#define CONFIG_SYS_CS3_START 0x80600000 -#define CONFIG_SYS_CS3_SIZE 0x00100000 -#define CONFIG_SYS_CS3_CFG 0x00019800 - -/* PMI Unicast 32Kbyte @0x80800000 */ -#define CONFIG_SYS_CS6_START CONFIG_SYS_PMI_UNI_BASE -#define CONFIG_SYS_CS6_SIZE 0x00008000 -#define CONFIG_SYS_CS6_CFG 0xFFFFF930 - -/* PMI Broadcast 32Kbyte @0x80810000 */ -#define CONFIG_SYS_CS7_START CONFIG_SYS_PMI_BROAD_BASE -#define CONFIG_SYS_CS7_SIZE 0x00008000 -#define CONFIG_SYS_CS7_CFG 0xFF00F930 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus */ - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_SYS_ISA_IO CONFIG_PCI_IO_BUS - -/*---------------------------------------------------------------------*/ -/* Display addresses */ -/*---------------------------------------------------------------------*/ - -#define CONFIG_SYS_DISP_CHR_RAM (CONFIG_SYS_DISPLAY_BASE + 0x38) -#define CONFIG_SYS_DISP_CWORD (CONFIG_SYS_DISPLAY_BASE + 0x30) - -#endif /* __CONFIG_H */ diff --git a/include/configs/uc100.h b/include/configs/uc100.h deleted file mode 100644 index cad897f70b..0000000000 --- a/include/configs/uc100.h +++ /dev/null @@ -1,482 +0,0 @@ -/* - * (C) Copyright 2000-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC860 1 -#define CONFIG_MPC860T 1 -#define CONFIG_MPC862 1 /* enable 862 since the */ -#define CONFIG_MPC857 1 /* 857 is a variant of the 862 */ - -#define CONFIG_UC100 1 /* ...on a UC100 module */ - -#define CONFIG_SYS_TEXT_BASE 0x40700000 - -#define MPC8XX_FACT 4 /* Multiply by 4 */ -#define MPC8XX_XIN 25000000 /* 25.0 MHz in */ -#define CONFIG_8xx_GCLK_FREQ (MPC8XX_FACT * MPC8XX_XIN) - /* define if cant' use get_gclk_freq */ - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE - -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ - -#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ - -#define CONFIG_BOOTCOUNT_LIMIT - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_BOARD_TYPES 1 /* support board types */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_8xx\0" \ - "bootfile=/tftpboot/uc100/uImage\0" \ - "kernel_addr=40000000\0" \ - "ramdisk_addr=40100000\0" \ - "load=tftp 100000 /tftpboot/uc100/u-boot.bin\0" \ - "update=protect off 40700000 4073ffff;era 40700000 4073ffff;" \ - "cp.b 100000 40700000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#undef CONFIG_STATUS_LED /* no status-led */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -#undef CONFIG_RTC_MPC8xx -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* PCF8563 RTC */ -#define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */ - -/* - * Power On Self Test support - */ -#define CONFIG_POST ( CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_SPR ) -#undef CONFIG_POST - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_MII -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PING -#define CONFIG_CMD_SNTP - -#ifdef CONFIG_POST -#define CONFIG_CMD_DIAG -#endif - - -#define CONFIG_NETCONSOLE - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#if 0 -#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xF0000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x40000000 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE+0x00700000) /* resetvec fff00100*/ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/*----------------------------------------------------------------------- - * Address accessed to reset the board - must not be mapped/assigned - */ -#define CONFIG_SYS_RESET_ADDRESS 0x90000000 - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE+CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR+CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_FRC | SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit - */ -#define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ - PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK 0x00000000 -#define CONFIG_SYS_SCCR (SCCR_EBDF11) - -/*----------------------------------------------------------------------- - * PCMCIA stuff - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) -#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) -#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) -#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) -#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) - -/*----------------------------------------------------------------------- - * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) - *----------------------------------------------------------------------- - */ - -#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ -#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ -#undef CONFIG_IDE_RESET /* reset for ide not supported */ - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 - -/*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */ - -/* used to re-map FLASH both when starting from SRAM or FLASH: - * restrict access enough to keep SRAM working (if any) - * but not too much to meddle with FLASH accesses - */ -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ - -/* - * FLASH timing: - */ -#define CONFIG_SYS_OR_TIMING_FLASH (0x00000d24) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) - -#define CONFIG_SYS_BR1_PRELIM 0x00000081 /* Chip select for SDRAM (32 Bit, UPMA) */ -#define CONFIG_SYS_OR1_PRELIM 0xfc000a00 -#define CONFIG_SYS_BR2_PRELIM 0x80000001 /* Chip select for SRAM (32 Bit, GPCM) */ -#define CONFIG_SYS_OR2_PRELIM 0xfff00d24 -#define CONFIG_SYS_BR3_PRELIM 0x80600401 /* Chip select for Display (8 Bit, GPCM) */ -#define CONFIG_SYS_OR3_PRELIM 0xffff8f44 -#define CONFIG_SYS_BR4_PRELIM 0xc05108c1 /* Chip select for Interbus MPM (16 Bit, UPMB) */ -#define CONFIG_SYS_OR4_PRELIM 0xffff0300 -#define CONFIG_SYS_BR5_PRELIM 0xc0500401 /* Chip select for Interbus Status (8 Bit, GPCM) */ -#define CONFIG_SYS_OR5_PRELIM 0xffff8db0 - -/* - * Memory Periodic Timer Prescaler - * - * The Divider for PTA (refresh timer) configuration is based on an - * example SDRAM configuration (64 MBit, one bank). The adjustment to - * the number of chip selects (NCS) and the actually needed refresh - * rate is done by setting MPTPR. - * - * PTA is calculated from - * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS) - * - * gclk CPU clock (not bus clock!) - * Trefresh Refresh cycle * 4 (four word bursts used) - * - * 4096 Rows from SDRAM example configuration - * 1000 factor s -> ms - * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration - * 4 Number of refresh cycles per period - * 64 Refresh cycle in ms per number of rows - * -------------------------------------------- - * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 - * - * 50 MHz => 50.000.000 / Divider = 98 - * 66 Mhz => 66.000.000 / Divider = 129 - * 80 Mhz => 80.000.000 / Divider = 156 - * 100 Mhz => 100.000.000 / Divider = 195 - */ - -#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64)) -#define CONFIG_SYS_MAMR_PTA 98 - -/* - * For 16 MBit, refresh rates could be 31.3 us - * (= 64 ms / 2K = 125 / quad bursts). - * For a simpler initialization, 15.6 us is used instead. - * - * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks - * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank - */ -#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ - -/* - * MAMR settings for SDRAM - */ - -/* 8 column SDRAM */ -#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - -#define CONFIG_SYS_MAMR_VAL 0x30904114 /* for SDRAM */ -#define CONFIG_SYS_MBMR_VAL 0xff001111 /* for Interbus-MPM */ - -/*----------------------------------------------------------------------- - * I2C stuff - */ - -/* enable I2C and select the hardware/software driver */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -/* - * Software (bit-bang) I2C driver configuration - */ -#define PB_SCL 0x00000020 /* PB 26 */ -#define PB_SDA 0x00000010 /* PB 27 */ - -#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) -#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) -#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) -#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) -#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ - else immr->im_cpm.cp_pbdat &= ~PB_SDA -#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ - else immr->im_cpm.cp_pbdat &= ~PB_SCL -#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ - -/*----------------------------------------------------------------------- - * I2C EEPROM (24C164) - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 /* EEPROM AT24C164 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 - -#define CONFIG_FEC_ENET 1 /* use FEC ethernet */ -#define FEC_ENET -#define CONFIG_MII -#define CONFIG_MII_INIT 1 -#define CONFIG_SYS_DISCOVER_PHY 1 - -#endif /* __CONFIG_H */ diff --git a/include/configs/uc101.h b/include/configs/uc101.h deleted file mode 100644 index f93dea7b37..0000000000 --- a/include/configs/uc101.h +++ /dev/null @@ -1,103 +0,0 @@ -/* - * (C) Copyright 2003-2009 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_UC101 1 /* UC101 board */ -#define CONFIG_HOSTNAME uc101 - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#endif -#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc5xxx/u-boot-customlayout.lds" - -#include "manroland/common.h" -#include "manroland/mpc5200-common.h" - -/* - * Serial console configuration - */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Flash configuration - */ -#define CONFIG_SYS_MAX_FLASH_SECT 140 - -/* - * Environment settings - */ -#define CONFIG_ENV_SECT_SIZE 0x10000 - -/* - * Memory map - */ -#define CONFIG_SYS_IB_MASTER 0xc0510000 /* CS 6 */ -#define CONFIG_SYS_IB_EPLD 0xc0500000 /* CS 7 */ - -/* SRAM */ -#define CONFIG_SYS_SRAM_SIZE 0x200000 - -/* - * GPIO configuration - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x4d558044 - -#define CONFIG_SYS_MEMTEST_START 0x00300000 -#define CONFIG_SYS_MEMTEST_END 0x00f00000 - -#define CONFIG_SYS_LOAD_ADDR 0x300000 - -#define CONFIG_SYS_BOOTCS_CFG 0x00045D00 - -/* 8Mbit SRAM @0x80100000 */ -#define CONFIG_SYS_CS1_SIZE 0x00200000 -#define CONFIG_SYS_CS1_CFG 0x21D00 - -/* Display H1, Status Inputs, EPLD @0x80600000 8 Bit */ -#define CONFIG_SYS_CS3_START CONFIG_SYS_DISPLAY_BASE -#define CONFIG_SYS_CS3_SIZE 0x00000100 -#define CONFIG_SYS_CS3_CFG 0x00081802 - -/* Interbus Master 16 Bit */ -#define CONFIG_SYS_CS6_START CONFIG_SYS_IB_MASTER -#define CONFIG_SYS_CS6_SIZE 0x00010000 -#define CONFIG_SYS_CS6_CFG 0x00FF3500 - -/* Interbus EPLD 8 Bit */ -#define CONFIG_SYS_CS7_START CONFIG_SYS_IB_EPLD -#define CONFIG_SYS_CS7_SIZE 0x00010000 -#define CONFIG_SYS_CS7_CFG 0x00081800 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus*/ - -/*---------------------------------------------------------------------*/ -/* Display addresses */ -/*---------------------------------------------------------------------*/ -#define CONFIG_SYS_DISP_CHR_RAM (CONFIG_SYS_DISPLAY_BASE + 0x38) -#define CONFIG_SYS_DISP_CWORD (CONFIG_SYS_DISPLAY_BASE + 0x30) - -#endif /* __CONFIG_H */ diff --git a/include/pcmcia.h b/include/pcmcia.h index 00065b2fdd..2ff399b81d 100644 --- a/include/pcmcia.h +++ b/include/pcmcia.h @@ -33,8 +33,6 @@ # define CONFIG_PCMCIA_SLOT_B #elif defined(CONFIG_ATC) /* The ATC use SLOT_A */ # define CONFIG_PCMCIA_SLOT_A -#elif defined(CONFIG_UC100) /* The UC100 use SLOT_B */ -# define CONFIG_PCMCIA_SLOT_B #else # error "PCMCIA Slot not configured" #endif