From: Enric Balletbò i Serra Date: Fri, 6 Dec 2013 20:30:24 +0000 (+0100) Subject: OMAP3: igep00x0: Convert to ti_omap3_common.h. X-Git-Tag: v2014.04-rc1~77^2~40^2~5 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=e37e954eba3edb5015a0a02880d57517f57425d8;p=u-boot OMAP3: igep00x0: Convert to ti_omap3_common.h. To reduce code duplication update omap3_igep00x0.h to use ti_omap3_common.h. Signed-off-by: Enric Balletbo i Serra --- diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h index 71062a601f..20fbbecdfb 100644 --- a/include/configs/omap3_igep00x0.h +++ b/include/configs/omap3_igep00x0.h @@ -10,20 +10,13 @@ #ifndef __IGEP00X0_H #define __IGEP00X0_H -#include - -/* - * High Level Configuration Options - */ -#define CONFIG_OMAP 1 /* in a TI OMAP core */ -#define CONFIG_OMAP34XX 1 /* which is a 34XX */ -#define CONFIG_OMAP_GPIO -#define CONFIG_OMAP_COMMON +#ifdef CONFIG_BOOT_NAND +#define CONFIG_NAND +#endif -#define CONFIG_SDRC /* The chip has SDRC controller */ +#define CONFIG_NR_DRAM_BANKS 2 -#include -#include +#include #include /* @@ -32,47 +25,12 @@ #define CONFIG_DISPLAY_CPUINFO 1 #define CONFIG_DISPLAY_BOARDINFO 1 -/* Clock Defines */ -#define V_OSCK 26000000 /* Clock output from T2 */ -#define V_SCLK (V_OSCK >> 1) - #define CONFIG_MISC_INIT_R -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 #define CONFIG_REVISION_TAG 1 -#define CONFIG_OF_LIBFDT -#define CONFIG_CMD_BOOTZ #define CONFIG_SUPPORT_RAW_INITRD -/* - * NS16550 Configuration - */ - -#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ - -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK - -/* select serial console configuration */ -#define CONFIG_CONS_INDEX 3 -#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 -#define CONFIG_SERIAL3 3 - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, \ - 115200} -#define CONFIG_GENERIC_MMC 1 -#define CONFIG_MMC 1 -#define CONFIG_OMAP_HSMMC 1 -#define CONFIG_DOS_PARTITION 1 - /* define to enable boot progress via leds */ #if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020) || \ (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0030) @@ -95,21 +53,10 @@ #define CONFIG_USBD_MANUFACTURER "Texas Instruments" #define CONFIG_USBD_PRODUCT_NAME "IGEP" -/* commands to include */ -#include - #define CONFIG_CMD_CACHE -#define CONFIG_CMD_EXT4 -#define CONFIG_CMD_FAT /* FAT support */ -#define CONFIG_CMD_FS_GENERIC -#define CONFIG_CMD_I2C /* I2C serial bus support */ -#define CONFIG_CMD_MMC /* MMC support */ #ifdef CONFIG_BOOT_ONENAND #define CONFIG_CMD_ONENAND /* ONENAND support */ #endif -#ifdef CONFIG_BOOT_NAND -#define CONFIG_CMD_NAND -#endif #if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020) || \ (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0032) #define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ @@ -117,24 +64,8 @@ #define CONFIG_CMD_DHCP #define CONFIG_CMD_PING #define CONFIG_CMD_NFS /* NFS support */ -#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ -#define CONFIG_MTD_DEVICE - -#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ -#undef CONFIG_CMD_IMLS /* List all found images */ -#define CONFIG_SYS_NO_FLASH -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_OMAP34XX -#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 -#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 - -/* - * TWL4030 - */ -#define CONFIG_TWL4030_POWER 1 - -#define CONFIG_BOOTDELAY 3 +/*#undef CONFIG_ENV_IS_NOWHERE*/ #define CONFIG_EXTRA_ENV_SETTINGS \ "usbtty=cdc_acm\0" \ @@ -205,48 +136,6 @@ "fi;" \ "run nandboot;" \ -#define CONFIG_AUTO_COMPLETE 1 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ -#define CONFIG_SYS_PROMPT "U-Boot # " -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) - -#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */ - /* works on */ -#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ - 0x01F00000) /* 31MB */ - -#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */ - /* load address */ - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) - -/* - * OMAP3 has 12 GP timers, they can be driven by the system clock - * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). - * This rate is divided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ - -/* - * Physical Memory Map - * - */ -#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ -#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 -#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 - /* * FLASH and environment organization */ @@ -263,23 +152,15 @@ #define CONFIG_ENV_ADDR ONENAND_ENV_OFFSET #endif -#ifdef CONFIG_BOOT_NAND +#ifdef CONFIG_NAND #define PISMO1_NAND_SIZE GPMC_SIZE_128M /* Configure the PISMO */ -#define CONFIG_NAND_OMAP_GPMC -#define CONFIG_SYS_NAND_BASE NAND_BASE #define GPMC_NAND_ECC_LP_x16_LAYOUT 1 #define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */ #define CONFIG_ENV_IS_IN_NAND 1 #define CONFIG_ENV_SIZE (512 << 10) /* Total Size Environment */ #define CONFIG_ENV_ADDR NAND_ENV_OFFSET -#define CONFIG_SYS_MAX_NAND_DEVICE 1 #endif -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) - /* * SMSC911x Ethernet */ @@ -289,54 +170,9 @@ #define CONFIG_SMC911X_BASE 0x2C000000 #endif /* (CONFIG_CMD_NET) */ -/* - * Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader - * and older u-boot.bin with the new U-Boot SPL. - */ -#define CONFIG_SYS_TEXT_BASE 0x80008000 -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 -#define CONFIG_SYS_INIT_RAM_SIZE 0x800 -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* SPL */ -#define CONFIG_SPL -#define CONFIG_SPL_FRAMEWORK -#define CONFIG_SPL_NAND_SIMPLE -#define CONFIG_SPL_TEXT_BASE 0x40200800 -#define CONFIG_SPL_MAX_SIZE (54 * 1024) -#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK - -/* move malloc and bss high to prevent clashing with the main image */ -#define CONFIG_SYS_SPL_MALLOC_START 0x87000000 -#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 -#define CONFIG_SPL_BSS_START_ADDR 0x87080000 /* end of minimum RAM */ -#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ - -/* MMC boot config */ -#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ -#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ -#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 -#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" - -#define CONFIG_SPL_BOARD_INIT -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBDISK_SUPPORT -#define CONFIG_SPL_I2C_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_MMC_SUPPORT -#define CONFIG_SPL_FAT_SUPPORT -#define CONFIG_SPL_SERIAL_SUPPORT - -#define CONFIG_SPL_POWER_SUPPORT -#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" - +/* OneNAND boot config */ #ifdef CONFIG_BOOT_ONENAND #define CONFIG_SPL_ONENAND_SUPPORT - -/* OneNAND boot config */ #define CONFIG_SYS_ONENAND_U_BOOT_OFFS 0x80000 #define CONFIG_SYS_ONENAND_PAGE_SIZE 2048 #define CONFIG_SPL_ONENAND_LOAD_ADDR 0x80000 @@ -345,13 +181,8 @@ #endif -#ifdef CONFIG_BOOT_NAND -#define CONFIG_SPL_NAND_SUPPORT -#define CONFIG_SPL_NAND_BASE -#define CONFIG_SPL_NAND_DRIVERS -#define CONFIG_SPL_NAND_ECC - /* NAND boot config */ +#ifdef CONFIG_NAND #define CONFIG_SYS_NAND_5_ADDR_CYCLE #define CONFIG_SYS_NAND_PAGE_COUNT 64 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 @@ -363,8 +194,6 @@ #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 3 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 #endif #endif /* __IGEP00X0_H */