From: Wolfgang Denk Date: Sat, 5 Nov 2011 05:13:14 +0000 (+0000) Subject: board/sacsng/sacsng.c: CodingStyle cleanup X-Git-Tag: v2011.12-rc1~236 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=e615de0ab36be3aecdf36ccf10d8ec40c6b477f7;p=u-boot board/sacsng/sacsng.c: CodingStyle cleanup Make (mostly) checkpatch clean. Signed-off-by: Wolfgang Denk Cc: Jerry Van Baren --- diff --git a/board/sacsng/sacsng.c b/board/sacsng/sacsng.c index 61cab87035..09f59a0f0d 100644 --- a/board/sacsng/sacsng.c +++ b/board/sacsng/sacsng.c @@ -39,7 +39,7 @@ extern void eth_loopback_test(void); #endif /* CONFIG_ETHER_LOOPBACK_TEST */ #include "clkinit.h" -#include "ioconfig.h" /* I/O configuration table */ +#include "ioconfig.h" /* I/O configuration table */ /* * PBI Page Based Interleaving @@ -61,88 +61,86 @@ extern void eth_loopback_test(void); /* * ADC/DAC Defines: */ -#define INITIAL_SAMPLE_RATE 10016 /* Initial Daq sample rate */ -#define INITIAL_RIGHT_JUST 0 /* Initial DAC right justification */ -#define INITIAL_MCLK_DIVIDE 0 /* Initial MCLK Divide */ -#define INITIAL_SAMPLE_64X 1 /* Initial 64x clocking mode */ -#define INITIAL_SAMPLE_128X 0 /* Initial 128x clocking mode */ +#define INITIAL_SAMPLE_RATE 10016 /* Initial Daq sample rate */ +#define INITIAL_RIGHT_JUST 0 /* Initial DAC right justification */ +#define INITIAL_MCLK_DIVIDE 0 /* Initial MCLK Divide */ +#define INITIAL_SAMPLE_64X 1 /* Initial 64x clocking mode */ +#define INITIAL_SAMPLE_128X 0 /* Initial 128x clocking mode */ /* * ADC Defines: */ -#define I2C_ADC_1_ADDR 0x0E /* I2C Address of the ADC #1 */ -#define I2C_ADC_2_ADDR 0x0F /* I2C Address of the ADC #2 */ +#define I2C_ADC_1_ADDR 0x0E /* I2C Address of the ADC #1 */ +#define I2C_ADC_2_ADDR 0x0F /* I2C Address of the ADC #2 */ -#define ADC_SDATA1_MASK 0x00020000 /* PA14 - CH12SDATA_PU */ -#define ADC_SDATA2_MASK 0x00010000 /* PA15 - CH34SDATA_PU */ +#define ADC_SDATA1_MASK 0x00020000 /* PA14 - CH12SDATA_PU */ +#define ADC_SDATA2_MASK 0x00010000 /* PA15 - CH34SDATA_PU */ -#define ADC_VREF_CAP 100 /* VREF capacitor in uF */ -#define ADC_INITIAL_DELAY (10 * ADC_VREF_CAP) /* 10 usec per uF, in usec */ -#define ADC_SDATA_DELAY 100 /* ADC SDATA release delay in usec */ +#define ADC_VREF_CAP 100 /* VREF capacitor in uF */ +#define ADC_INITIAL_DELAY (10 * ADC_VREF_CAP) /* 10 usec per uF, in usec */ +#define ADC_SDATA_DELAY 100 /* ADC SDATA release delay in usec */ #define ADC_CAL_DELAY (1000000 / INITIAL_SAMPLE_RATE * 4500) - /* Wait at least 4100 LRCLK's */ - -#define ADC_REG1_FRAME_START 0x80 /* Frame start */ -#define ADC_REG1_GROUND_CAL 0x40 /* Ground calibration enable */ -#define ADC_REG1_ANA_MOD_PDOWN 0x20 /* Analog modulator section in power down */ -#define ADC_REG1_DIG_MOD_PDOWN 0x10 /* Digital modulator section in power down */ - -#define ADC_REG2_128x 0x80 /* Oversample at 128x */ -#define ADC_REG2_CAL 0x40 /* System calibration enable */ -#define ADC_REG2_CHANGE_SIGN 0x20 /* Change sign enable */ -#define ADC_REG2_LR_DISABLE 0x10 /* Left/Right output disable */ -#define ADC_REG2_HIGH_PASS_DIS 0x08 /* High pass filter disable */ -#define ADC_REG2_SLAVE_MODE 0x04 /* Slave mode */ -#define ADC_REG2_DFS 0x02 /* Digital format select */ -#define ADC_REG2_MUTE 0x01 /* Mute */ - -#define ADC_REG7_ADDR_ENABLE 0x80 /* Address enable */ -#define ADC_REG7_PEAK_ENABLE 0x40 /* Peak enable */ -#define ADC_REG7_PEAK_UPDATE 0x20 /* Peak update */ -#define ADC_REG7_PEAK_FORMAT 0x10 /* Peak display format */ -#define ADC_REG7_DIG_FILT_PDOWN 0x04 /* Digital filter power down enable */ -#define ADC_REG7_FIR2_IN_EN 0x02 /* External FIR2 input enable */ -#define ADC_REG7_PSYCHO_EN 0x01 /* External pyscho filter input enable */ + /* Wait at least 4100 LRCLK's */ + +#define ADC_REG1_FRAME_START 0x80 /* Frame start */ +#define ADC_REG1_GROUND_CAL 0x40 /* Ground calibration enable */ +#define ADC_REG1_ANA_MOD_PDOWN 0x20 /* Analog modulator section in power down */ +#define ADC_REG1_DIG_MOD_PDOWN 0x10 /* Digital modulator section in power down */ + +#define ADC_REG2_128x 0x80 /* Oversample at 128x */ +#define ADC_REG2_CAL 0x40 /* System calibration enable */ +#define ADC_REG2_CHANGE_SIGN 0x20 /* Change sign enable */ +#define ADC_REG2_LR_DISABLE 0x10 /* Left/Right output disable */ +#define ADC_REG2_HIGH_PASS_DIS 0x08 /* High pass filter disable */ +#define ADC_REG2_SLAVE_MODE 0x04 /* Slave mode */ +#define ADC_REG2_DFS 0x02 /* Digital format select */ +#define ADC_REG2_MUTE 0x01 /* Mute */ + +#define ADC_REG7_ADDR_ENABLE 0x80 /* Address enable */ +#define ADC_REG7_PEAK_ENABLE 0x40 /* Peak enable */ +#define ADC_REG7_PEAK_UPDATE 0x20 /* Peak update */ +#define ADC_REG7_PEAK_FORMAT 0x10 /* Peak display format */ +#define ADC_REG7_DIG_FILT_PDOWN 0x04 /* Digital filter power down enable */ +#define ADC_REG7_FIR2_IN_EN 0x02 /* External FIR2 input enable */ +#define ADC_REG7_PSYCHO_EN 0x01 /* External pyscho filter input enable */ /* * DAC Defines: */ -#define I2C_DAC_ADDR 0x11 /* I2C Address of the DAC */ +#define I2C_DAC_ADDR 0x11 /* I2C Address of the DAC */ -#define DAC_RST_MASK 0x00008000 /* PA16 - DAC_RST* */ -#define DAC_RESET_DELAY 100 /* DAC reset delay in usec */ -#define DAC_INITIAL_DELAY 5000 /* DAC initialization delay in usec */ +#define DAC_RST_MASK 0x00008000 /* PA16 - DAC_RST* */ +#define DAC_RESET_DELAY 100 /* DAC reset delay in usec */ +#define DAC_INITIAL_DELAY 5000 /* DAC initialization delay in usec */ -#define DAC_REG1_AMUTE 0x80 /* Auto-mute */ +#define DAC_REG1_AMUTE 0x80 /* Auto-mute */ -#define DAC_REG1_LEFT_JUST_24_BIT (0 << 4) /* Fmt 0: Left justified 24 bit */ -#define DAC_REG1_I2S_24_BIT (1 << 4) /* Fmt 1: I2S up to 24 bit */ -#define DAC_REG1_RIGHT_JUST_16BIT (2 << 4) /* Fmt 2: Right justified 16 bit */ -#define DAC_REG1_RIGHT_JUST_24BIT (3 << 4) /* Fmt 3: Right justified 24 bit */ -#define DAC_REG1_RIGHT_JUST_20BIT (4 << 4) /* Fmt 4: Right justified 20 bit */ -#define DAC_REG1_RIGHT_JUST_18BIT (5 << 4) /* Fmt 5: Right justified 18 bit */ +#define DAC_REG1_LEFT_JUST_24_BIT (0 << 4) /* Fmt 0: Left justified 24 bit */ +#define DAC_REG1_I2S_24_BIT (1 << 4) /* Fmt 1: I2S up to 24 bit */ +#define DAC_REG1_RIGHT_JUST_16BIT (2 << 4) /* Fmt 2: Right justified 16 bit */ +#define DAC_REG1_RIGHT_JUST_24BIT (3 << 4) /* Fmt 3: Right justified 24 bit */ +#define DAC_REG1_RIGHT_JUST_20BIT (4 << 4) /* Fmt 4: Right justified 20 bit */ +#define DAC_REG1_RIGHT_JUST_18BIT (5 << 4) /* Fmt 5: Right justified 18 bit */ -#define DAC_REG1_DEM_NO (0 << 2) /* No De-emphasis */ -#define DAC_REG1_DEM_44KHZ (1 << 2) /* 44.1KHz De-emphasis */ -#define DAC_REG1_DEM_48KHZ (2 << 2) /* 48KHz De-emphasis */ -#define DAC_REG1_DEM_32KHZ (3 << 2) /* 32KHz De-emphasis */ +#define DAC_REG1_DEM_NO (0 << 2) /* No De-emphasis */ +#define DAC_REG1_DEM_44KHZ (1 << 2) /* 44.1KHz De-emphasis */ +#define DAC_REG1_DEM_48KHZ (2 << 2) /* 48KHz De-emphasis */ +#define DAC_REG1_DEM_32KHZ (3 << 2) /* 32KHz De-emphasis */ -#define DAC_REG1_SINGLE 0 /* 4- 50KHz sample rate */ -#define DAC_REG1_DOUBLE 1 /* 50-100KHz sample rate */ -#define DAC_REG1_QUAD 2 /* 100-200KHz sample rate */ -#define DAC_REG1_DSD 3 /* Direct Stream Data, DSD */ +#define DAC_REG1_SINGLE 0 /* 4- 50KHz sample rate */ +#define DAC_REG1_DOUBLE 1 /* 50-100KHz sample rate */ +#define DAC_REG1_QUAD 2 /* 100-200KHz sample rate */ +#define DAC_REG1_DSD 3 /* Direct Stream Data, DSD */ -#define DAC_REG5_INVERT_A 0x80 /* Invert channel A */ -#define DAC_REG5_INVERT_B 0x40 /* Invert channel B */ -#define DAC_REG5_I2C_MODE 0x20 /* Control port (I2C) mode */ -#define DAC_REG5_POWER_DOWN 0x10 /* Power down mode */ -#define DAC_REG5_MUTEC_A_B 0x08 /* Mutec A=B */ -#define DAC_REG5_FREEZE 0x04 /* Freeze */ -#define DAC_REG5_MCLK_DIV 0x02 /* MCLK divide by 2 */ -#define DAC_REG5_RESERVED 0x01 /* Reserved */ - -/* ------------------------------------------------------------------------- */ +#define DAC_REG5_INVERT_A 0x80 /* Invert channel A */ +#define DAC_REG5_INVERT_B 0x40 /* Invert channel B */ +#define DAC_REG5_I2C_MODE 0x20 /* Control port (I2C) mode */ +#define DAC_REG5_POWER_DOWN 0x10 /* Power down mode */ +#define DAC_REG5_MUTEC_A_B 0x08 /* Mutec A=B */ +#define DAC_REG5_FREEZE 0x04 /* Freeze */ +#define DAC_REG5_MCLK_DIV 0x02 /* MCLK divide by 2 */ +#define DAC_REG5_RESERVED 0x01 /* Reserved */ /* * Check Board Identity: @@ -150,290 +148,299 @@ extern void eth_loopback_test(void); int checkboard(void) { - printf ("SACSng\n"); + printf("SACSng\n"); - return 0; + return 0; } -/* ------------------------------------------------------------------------- */ - phys_size_t initdram(int board_type) { - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile memctl8260_t *memctl = &immap->im_memctl; - volatile uchar c = 0; - volatile uchar *ramaddr = (uchar *)(CONFIG_SYS_SDRAM_BASE + 0x8); - uint psdmr = CONFIG_SYS_PSDMR; - int i; - uint psrt = 14; /* for no SPD */ - uint chipselects = 1; /* for no SPD */ - uint sdram_size = CONFIG_SYS_SDRAM0_SIZE * 1024 * 1024; /* for no SPD */ - uint or = CONFIG_SYS_OR2_PRELIM; /* for no SPD */ + volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; + volatile memctl8260_t *memctl = &immap->im_memctl; + volatile uchar c = 0; + volatile uchar *ramaddr = (uchar *)(CONFIG_SYS_SDRAM_BASE + 0x8); + uint psdmr = CONFIG_SYS_PSDMR; + int i; + uint psrt = 14; /* for no SPD */ + uint chipselects = 1; /* for no SPD */ + uint sdram_size = CONFIG_SYS_SDRAM0_SIZE * 1024 * 1024; /* for no SPD */ + uint or = CONFIG_SYS_OR2_PRELIM; /* for no SPD */ + #ifdef SDRAM_SPD_ADDR - uint data_width; - uint rows; - uint banks; - uint cols; - uint caslatency; - uint width; - uint rowst; - uint sdam; - uint bsma; - uint sda10; - u_char spd_size; - u_char data; - u_char cksum; - int j; + uint data_width; + uint rows; + uint banks; + uint cols; + uint caslatency; + uint width; + uint rowst; + uint sdam; + uint bsma; + uint sda10; + u_char spd_size; + u_char data; + u_char cksum; + int j; #endif #ifdef SDRAM_SPD_ADDR - /* Keep the compiler from complaining about potentially uninitialized vars */ - data_width = chipselects = rows = banks = cols = caslatency = psrt = 0; - - /* - * Read the SDRAM SPD EEPROM via I2C. - */ - i2c_read(SDRAM_SPD_ADDR, 0, 1, &data, 1); - spd_size = data; - cksum = data; - for(j = 1; j < 64; j++) { /* read only the checksummed bytes */ - /* note: the I2C address autoincrements when alen == 0 */ - i2c_read(SDRAM_SPD_ADDR, 0, 0, &data, 1); - if(j == 5) chipselects = data & 0x0F; - else if(j == 6) data_width = data; - else if(j == 7) data_width |= data << 8; - else if(j == 3) rows = data & 0x0F; - else if(j == 4) cols = data & 0x0F; - else if(j == 12) { - /* - * Refresh rate: this assumes the prescaler is set to - * approximately 1uSec per tick. - */ - switch(data & 0x7F) { - default: - case 0: psrt = 14 ; /* 15.625uS */ break; - case 1: psrt = 2; /* 3.9uS */ break; - case 2: psrt = 6; /* 7.8uS */ break; - case 3: psrt = 29; /* 31.3uS */ break; - case 4: psrt = 60; /* 62.5uS */ break; - case 5: psrt = 120; /* 125uS */ break; - } - } - else if(j == 17) banks = data; - else if(j == 18) { - caslatency = 3; /* default CL */ + /* Keep the compiler from complaining about potentially uninitialized vars */ + data_width = chipselects = rows = banks = cols = caslatency = psrt = + 0; + + /* + * Read the SDRAM SPD EEPROM via I2C. + */ + i2c_read(SDRAM_SPD_ADDR, 0, 1, &data, 1); + spd_size = data; + cksum = data; + for (j = 1; j < 64; j++) { /* read only the checksummed bytes */ + /* note: the I2C address autoincrements when alen == 0 */ + i2c_read(SDRAM_SPD_ADDR, 0, 0, &data, 1); + if (j == 5) + chipselects = data & 0x0F; + else if (j == 6) + data_width = data; + else if (j == 7) + data_width |= data << 8; + else if (j == 3) + rows = data & 0x0F; + else if (j == 4) + cols = data & 0x0F; + else if (j == 12) { + /* + * Refresh rate: this assumes the prescaler is set to + * approximately 1uSec per tick. + */ + switch (data & 0x7F) { + default: + case 0: + psrt = 14; /* 15.625uS */ + break; + case 1: + psrt = 2; /* 3.9uS */ + break; + case 2: + psrt = 6; /* 7.8uS */ + break; + case 3: + psrt = 29; /* 31.3uS */ + break; + case 4: + psrt = 60; /* 62.5uS */ + break; + case 5: + psrt = 120; /* 125uS */ + break; + } + } else if (j == 17) + banks = data; + else if (j == 18) { + caslatency = 3; /* default CL */ #if(PESSIMISTIC_SDRAM) - if((data & 0x04) != 0) caslatency = 3; - else if((data & 0x02) != 0) caslatency = 2; - else if((data & 0x01) != 0) caslatency = 1; + if ((data & 0x04) != 0) + caslatency = 3; + else if ((data & 0x02) != 0) + caslatency = 2; + else if ((data & 0x01) != 0) + caslatency = 1; #else - if((data & 0x01) != 0) caslatency = 1; - else if((data & 0x02) != 0) caslatency = 2; - else if((data & 0x04) != 0) caslatency = 3; + if ((data & 0x01) != 0) + caslatency = 1; + else if ((data & 0x02) != 0) + caslatency = 2; + else if ((data & 0x04) != 0) + caslatency = 3; #endif - else { - printf ("WARNING: Unknown CAS latency 0x%02X, using 3\n", - data); - } + else { + printf("WARNING: Unknown CAS latency 0x%02X, using 3\n", data); + } + } else if (j == 63) { + if (data != cksum) { + printf("WARNING: Configuration data checksum failure:" " is 0x%02x, calculated 0x%02x\n", data, cksum); + } + } + cksum += data; } - else if(j == 63) { - if(data != cksum) { - printf ("WARNING: Configuration data checksum failure:" - " is 0x%02x, calculated 0x%02x\n", - data, cksum); - } + + /* We don't trust CL less than 2 (only saw it on an old 16MByte DIMM) */ + if (caslatency < 2) { + printf("WARNING: CL was %d, forcing to 2\n", caslatency); + caslatency = 2; + } + if (rows > 14) { + printf("WARNING: This doesn't look good, rows = %d, should be <= 14\n", + rows); + rows = 14; + } + if (cols > 11) { + printf("WARNING: This doesn't look good, columns = %d, should be <= 11\n", + cols); + cols = 11; + } + + if ((data_width != 64) && (data_width != 72)) { + printf("WARNING: SDRAM width unsupported, is %d, expected 64 or 72.\n", + data_width); } - cksum += data; - } - - /* We don't trust CL less than 2 (only saw it on an old 16MByte DIMM) */ - if(caslatency < 2) { - printf("WARNING: CL was %d, forcing to 2\n", caslatency); - caslatency = 2; - } - if(rows > 14) { - printf("WARNING: This doesn't look good, rows = %d, should be <= 14\n", rows); - rows = 14; - } - if(cols > 11) { - printf("WARNING: This doesn't look good, columns = %d, should be <= 11\n", cols); - cols = 11; - } - - if((data_width != 64) && (data_width != 72)) - { - printf("WARNING: SDRAM width unsupported, is %d, expected 64 or 72.\n", - data_width); - } - width = 3; /* 2^3 = 8 bytes = 64 bits wide */ - /* - * Convert banks into log2(banks) - */ - if (banks == 2) banks = 1; - else if(banks == 4) banks = 2; - else if(banks == 8) banks = 3; - - sdram_size = 1 << (rows + cols + banks + width); - -#if(CONFIG_PBI == 0) /* bank-based interleaving */ - rowst = ((32 - 6) - (rows + cols + width)) * 2; + width = 3; /* 2^3 = 8 bytes = 64 bits wide */ + /* + * Convert banks into log2(banks) + */ + if (banks == 2) + banks = 1; + else if (banks == 4) + banks = 2; + else if (banks == 8) + banks = 3; + + sdram_size = 1 << (rows + cols + banks + width); + +#if(CONFIG_PBI == 0) /* bank-based interleaving */ + rowst = ((32 - 6) - (rows + cols + width)) * 2; #else - rowst = 32 - (rows + banks + cols + width); + rowst = 32 - (rows + banks + cols + width); #endif - or = ~(sdram_size - 1) | /* SDAM address mask */ - ((banks-1) << 13) | /* banks per device */ - (rowst << 9) | /* rowst */ - ((rows - 9) << 6); /* numr */ - - memctl->memc_or2 = or; - - /* - * SDAM specifies the number of columns that are multiplexed - * (reference AN2165/D), defined to be (columns - 6) for page - * interleave, (columns - 8) for bank interleave. - * - * BSMA is 14 - max(rows, cols). The bank select lines come - * into play above the highest "address" line going into the - * the SDRAM. - */ -#if(CONFIG_PBI == 0) /* bank-based interleaving */ - sdam = cols - 8; - bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols); - sda10 = sdam + 2; + or = ~(sdram_size - 1) | /* SDAM address mask */ + ((banks - 1) << 13) | /* banks per device */ + (rowst << 9) | /* rowst */ + ((rows - 9) << 6); /* numr */ + + memctl->memc_or2 = or; + + /* + * SDAM specifies the number of columns that are multiplexed + * (reference AN2165/D), defined to be (columns - 6) for page + * interleave, (columns - 8) for bank interleave. + * + * BSMA is 14 - max(rows, cols). The bank select lines come + * into play above the highest "address" line going into the + * the SDRAM. + */ +#if(CONFIG_PBI == 0) /* bank-based interleaving */ + sdam = cols - 8; + bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols); + sda10 = sdam + 2; #else - sdam = cols - 6; - bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols); - sda10 = sdam; + sdam = cols - 6; + bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols); + sda10 = sdam; #endif #if(PESSIMISTIC_SDRAM) - psdmr = (CONFIG_PBI |\ - PSDMR_RFEN |\ - PSDMR_RFRC_16_CLK |\ - PSDMR_PRETOACT_8W |\ - PSDMR_ACTTORW_8W |\ - PSDMR_WRC_4C |\ - PSDMR_EAMUX |\ - PSDMR_BUFCMD) |\ - caslatency |\ - ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */ \ - (sdam << 24) |\ - (bsma << 21) |\ - (sda10 << 18); + psdmr = (CONFIG_PBI | PSDMR_RFEN | PSDMR_RFRC_16_CLK | + PSDMR_PRETOACT_8W | PSDMR_ACTTORW_8W | PSDMR_WRC_4C | + PSDMR_EAMUX | PSDMR_BUFCMD) | caslatency | + ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */ + (sdam << 24) | (bsma << 21) | (sda10 << 18); #else - psdmr = (CONFIG_PBI |\ - PSDMR_RFEN |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_3W | /* 1 for 7E parts (fast PC-133) */ \ - PSDMR_ACTTORW_2W | /* 1 for 7E parts (fast PC-133) */ \ - PSDMR_WRC_1C | /* 1 clock + 7nSec */ - EAMUX |\ - BUFCMD) |\ - caslatency |\ - ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */ \ - (sdam << 24) |\ - (bsma << 21) |\ - (sda10 << 18); + psdmr = (CONFIG_PBI | PSDMR_RFEN | PSDMR_RFRC_7_CLK | + PSDMR_PRETOACT_3W | /* 1 for 7E parts (fast PC-133) */ + PSDMR_ACTTORW_2W | /* 1 for 7E parts (fast PC-133) */ + PSDMR_WRC_1C | /* 1 clock + 7nSec */ + EAMUX | BUFCMD) | + caslatency | ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */ + (sdam << 24) | (bsma << 21) | (sda10 << 18); #endif #endif - /* - * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35): - * - * "At system reset, initialization software must set up the - * programmable parameters in the memory controller banks registers - * (ORx, BRx, P/LSDMR). After all memory parameters are configured, - * system software should execute the following initialization sequence - * for each SDRAM device. - * - * 1. Issue a PRECHARGE-ALL-BANKS command - * 2. Issue eight CBR REFRESH commands - * 3. Issue a MODE-SET command to initialize the mode register - * - * Quote from Micron MT48LC8M16A2 data sheet: - * - * "...the SDRAM requires a 100uS delay prior to issuing any - * command other than a COMMAND INHIBIT or NOP. Starting at some - * point during this 100uS period and continuing at least through - * the end of this period, COMMAND INHIBIT or NOP commands should - * be applied." - * - * "Once the 100uS delay has been satisfied with at least one COMMAND - * INHIBIT or NOP command having been applied, a /PRECHARGE command/ - * should be applied. All banks must then be precharged, thereby - * placing the device in the all banks idle state." - * - * "Once in the idle state, /two/ AUTO REFRESH cycles must be - * performed. After the AUTO REFRESH cycles are complete, the - * SDRAM is ready for mode register programming." - * - * (/emphasis/ mine, gvb) - * - * The way I interpret this, Micron start up sequence is: - * 1. Issue a PRECHARGE-BANK command (initial precharge) - * 2. Issue a PRECHARGE-ALL-BANKS command ("all banks ... precharged") - * 3. Issue two (presumably, doing eight is OK) CBR REFRESH commands - * 4. Issue a MODE-SET command to initialize the mode register - * - * -------- - * - * The initial commands are executed by setting P/LSDMR[OP] and - * accessing the SDRAM with a single-byte transaction." - * - * The appropriate BRx/ORx registers have already been set when we - * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE. - */ - - memctl->memc_mptpr = CONFIG_SYS_MPTPR; - memctl->memc_psrt = psrt; - - memctl->memc_psdmr = psdmr | PSDMR_OP_PREA; - *ramaddr = c; - - memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR; - for (i = 0; i < 8; i++) - *ramaddr = c; - - memctl->memc_psdmr = psdmr | PSDMR_OP_MRW; - *ramaddr = c; - - memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN; - *ramaddr = c; - - /* - * Do it a second time for the second set of chips if the DIMM has - * two chip selects (double sided). - */ - if(chipselects > 1) { - ramaddr += sdram_size; + /* + * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35): + * + * "At system reset, initialization software must set up the + * programmable parameters in the memory controller banks registers + * (ORx, BRx, P/LSDMR). After all memory parameters are configured, + * system software should execute the following initialization sequence + * for each SDRAM device. + * + * 1. Issue a PRECHARGE-ALL-BANKS command + * 2. Issue eight CBR REFRESH commands + * 3. Issue a MODE-SET command to initialize the mode register + * + * Quote from Micron MT48LC8M16A2 data sheet: + * + * "...the SDRAM requires a 100uS delay prior to issuing any + * command other than a COMMAND INHIBIT or NOP. Starting at some + * point during this 100uS period and continuing at least through + * the end of this period, COMMAND INHIBIT or NOP commands should + * be applied." + * + * "Once the 100uS delay has been satisfied with at least one COMMAND + * INHIBIT or NOP command having been applied, a /PRECHARGE command/ + * should be applied. All banks must then be precharged, thereby + * placing the device in the all banks idle state." + * + * "Once in the idle state, /two/ AUTO REFRESH cycles must be + * performed. After the AUTO REFRESH cycles are complete, the + * SDRAM is ready for mode register programming." + * + * (/emphasis/ mine, gvb) + * + * The way I interpret this, Micron start up sequence is: + * 1. Issue a PRECHARGE-BANK command (initial precharge) + * 2. Issue a PRECHARGE-ALL-BANKS command ("all banks ... precharged") + * 3. Issue two (presumably, doing eight is OK) CBR REFRESH commands + * 4. Issue a MODE-SET command to initialize the mode register + * + * -------- + * + * The initial commands are executed by setting P/LSDMR[OP] and + * accessing the SDRAM with a single-byte transaction." + * + * The appropriate BRx/ORx registers have already been set when we + * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE. + */ - memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM + sdram_size; - memctl->memc_or3 = or; + memctl->memc_mptpr = CONFIG_SYS_MPTPR; + memctl->memc_psrt = psrt; memctl->memc_psdmr = psdmr | PSDMR_OP_PREA; *ramaddr = c; memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR; for (i = 0; i < 8; i++) - *ramaddr = c; + *ramaddr = c; memctl->memc_psdmr = psdmr | PSDMR_OP_MRW; *ramaddr = c; memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN; *ramaddr = c; - } - /* return total ram size */ - return (sdram_size * chipselects); + /* + * Do it a second time for the second set of chips if the DIMM has + * two chip selects (double sided). + */ + if (chipselects > 1) { + ramaddr += sdram_size; + + memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM + sdram_size; + memctl->memc_or3 = or; + + memctl->memc_psdmr = psdmr | PSDMR_OP_PREA; + *ramaddr = c; + + memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR; + for (i = 0; i < 8; i++) + *ramaddr = c; + + memctl->memc_psdmr = psdmr | PSDMR_OP_MRW; + *ramaddr = c; + + memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN; + *ramaddr = c; + } + + /* return total ram size */ + return (sdram_size * chipselects); } /*----------------------------------------------------------------------- * Board Control Functions */ -void board_poweroff (void) +void board_poweroff(void) { - while (1); /* hang forever */ + while (1); /* hang forever */ } @@ -441,301 +448,288 @@ void board_poweroff (void) /* ------------------------------------------------------------------------- */ int misc_init_r(void) { - /* - * Note: iop is used by the I2C macros, and iopa by the ADC/DAC initialization. - */ - volatile ioport_t *iopa = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 0 /* port A */); - volatile ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT); - - int reg; /* I2C register value */ - char *ep; /* Environment pointer */ - char str_buf[12] ; /* sprintf output buffer */ - int sample_rate; /* ADC/DAC sample rate */ - int sample_64x; /* Use 64/4 clocking for the ADC/DAC */ - int sample_128x; /* Use 128/4 clocking for the ADC/DAC */ - int right_just; /* Is the data to the DAC right justified? */ - int mclk_divide; /* MCLK Divide */ - int quiet; /* Quiet or minimal output mode */ - - quiet = 0; - if ((ep = getenv("quiet")) != NULL) { - quiet = simple_strtol(ep, NULL, 10); - } - else { - setenv("quiet", "0"); - } - - /* - * SACSng custom initialization: - * Start the ADC and DAC clocks, since the Crystal parts do not - * work on the I2C bus until the clocks are running. - */ - - sample_rate = INITIAL_SAMPLE_RATE; - if ((ep = getenv("DaqSampleRate")) != NULL) { - sample_rate = simple_strtol(ep, NULL, 10); - } - - sample_64x = INITIAL_SAMPLE_64X; - sample_128x = INITIAL_SAMPLE_128X; - if ((ep = getenv("Daq64xSampling")) != NULL) { - sample_64x = simple_strtol(ep, NULL, 10); + /* + * Note: iop is used by the I2C macros, and iopa by the ADC/DAC initialization. + */ + volatile ioport_t *iopa = + ioport_addr((immap_t *)CONFIG_SYS_IMMR, 0 /* port A */ ); + volatile ioport_t *iop = + ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT); + + int reg; /* I2C register value */ + char *ep; /* Environment pointer */ + char str_buf[12]; /* sprintf output buffer */ + int sample_rate; /* ADC/DAC sample rate */ + int sample_64x; /* Use 64/4 clocking for the ADC/DAC */ + int sample_128x; /* Use 128/4 clocking for the ADC/DAC */ + int right_just; /* Is the data to the DAC right justified? */ + int mclk_divide; /* MCLK Divide */ + int quiet; /* Quiet or minimal output mode */ + + quiet = 0; + + if ((ep = getenv("quiet")) != NULL) + quiet = simple_strtol(ep, NULL, 10); + else + setenv("quiet", "0"); + + /* + * SACSng custom initialization: + * Start the ADC and DAC clocks, since the Crystal parts do not + * work on the I2C bus until the clocks are running. + */ + + sample_rate = INITIAL_SAMPLE_RATE; + if ((ep = getenv("DaqSampleRate")) != NULL) + sample_rate = simple_strtol(ep, NULL, 10); + + sample_64x = INITIAL_SAMPLE_64X; + sample_128x = INITIAL_SAMPLE_128X; + if ((ep = getenv("Daq64xSampling")) != NULL) { + sample_64x = simple_strtol(ep, NULL, 10); + if (sample_64x) + sample_128x = 0; + else + sample_128x = 1; + } else { + if ((ep = getenv("Daq128xSampling")) != NULL) { + sample_128x = simple_strtol(ep, NULL, 10); + if (sample_128x) + sample_64x = 0; + else + sample_64x = 1; + } + } + + /* + * Stop the clocks and wait for at least 1 LRCLK period + * to make sure the clocking has really stopped. + */ + Daq_Stop_Clocks(); + udelay((1000000 / sample_rate) * NUM_LRCLKS_TO_STABILIZE); + + /* + * Initialize the clocks with the new rates + */ + Daq_Init_Clocks(sample_rate, sample_64x); + sample_rate = Daq_Get_SampleRate(); + + /* + * Start the clocks and wait for at least 1 LRCLK period + * to make sure the clocking has become stable. + */ + Daq_Start_Clocks(sample_rate); + udelay((1000000 / sample_rate) * NUM_LRCLKS_TO_STABILIZE); + + sprintf(str_buf, "%d", sample_rate); + setenv("DaqSampleRate", str_buf); + if (sample_64x) { - sample_128x = 0; + setenv("Daq64xSampling", "1"); + setenv("Daq128xSampling", NULL); + } else { + setenv("Daq64xSampling", NULL); + setenv("Daq128xSampling", "1"); } - else { - sample_128x = 1; + + /* + * Display the ADC/DAC clocking information + */ + if (!quiet) + Daq_Display_Clocks(); + + /* + * Determine the DAC data justification + */ + + right_just = INITIAL_RIGHT_JUST; + if ((ep = getenv("DaqDACRightJustified")) != NULL) + right_just = simple_strtol(ep, NULL, 10); + + sprintf(str_buf, "%d", right_just); + setenv("DaqDACRightJustified", str_buf); + + /* + * Determine the DAC MCLK Divide + */ + + mclk_divide = INITIAL_MCLK_DIVIDE; + if ((ep = getenv("DaqDACMClockDivide")) != NULL) + mclk_divide = simple_strtol(ep, NULL, 10); + + sprintf(str_buf, "%d", mclk_divide); + setenv("DaqDACMClockDivide", str_buf); + + /* + * Initializing the I2C address in the Crystal A/Ds: + * + * 1) Wait for VREF cap to settle (10uSec per uF) + * 2) Release pullup on SDATA + * 3) Write the I2C address to register 6 + * 4) Enable address matching by setting the MSB in register 7 + */ + + if (!quiet) + printf("Initializing the ADC...\n"); + + udelay(ADC_INITIAL_DELAY); /* 10uSec per uF of VREF cap */ + + iopa->pdat &= ~ADC_SDATA1_MASK; /* release SDATA1 */ + udelay(ADC_SDATA_DELAY); /* arbitrary settling time */ + + i2c_reg_write(0x00, 0x06, I2C_ADC_1_ADDR); /* set address */ + i2c_reg_write(I2C_ADC_1_ADDR, 0x07, /* turn on ADDREN */ + ADC_REG7_ADDR_ENABLE); + + i2c_reg_write(I2C_ADC_1_ADDR, 0x02, /* 128x, slave mode, !HPEN */ + (sample_64x ? 0 : ADC_REG2_128x) | + ADC_REG2_HIGH_PASS_DIS | ADC_REG2_SLAVE_MODE); + + reg = i2c_reg_read(I2C_ADC_1_ADDR, 0x06) & 0x7F; + if (reg != I2C_ADC_1_ADDR) { + printf("Init of ADC U10 failed: address is 0x%02X should be 0x%02X\n", + reg, I2C_ADC_1_ADDR); } - } - else { - if ((ep = getenv("Daq128xSampling")) != NULL) { - sample_128x = simple_strtol(ep, NULL, 10); - if (sample_128x) { - sample_64x = 0; - } - else { - sample_64x = 1; - } + + iopa->pdat &= ~ADC_SDATA2_MASK; /* release SDATA2 */ + udelay(ADC_SDATA_DELAY); /* arbitrary settling time */ + + /* set address (do not set ADDREN yet) */ + i2c_reg_write(0x00, 0x06, I2C_ADC_2_ADDR); + + i2c_reg_write(I2C_ADC_2_ADDR, 0x02, /* 64x, slave mode, !HPEN */ + (sample_64x ? 0 : ADC_REG2_128x) | + ADC_REG2_HIGH_PASS_DIS | ADC_REG2_SLAVE_MODE); + + reg = i2c_reg_read(I2C_ADC_2_ADDR, 0x06) & 0x7F; + if (reg != I2C_ADC_2_ADDR) { + printf("Init of ADC U15 failed: address is 0x%02X should be 0x%02X\n", + reg, I2C_ADC_2_ADDR); } - } - - /* - * Stop the clocks and wait for at least 1 LRCLK period - * to make sure the clocking has really stopped. - */ - Daq_Stop_Clocks(); - udelay((1000000 / sample_rate) * NUM_LRCLKS_TO_STABILIZE); - - /* - * Initialize the clocks with the new rates - */ - Daq_Init_Clocks(sample_rate, sample_64x); - sample_rate = Daq_Get_SampleRate(); - - /* - * Start the clocks and wait for at least 1 LRCLK period - * to make sure the clocking has become stable. - */ - Daq_Start_Clocks(sample_rate); - udelay((1000000 / sample_rate) * NUM_LRCLKS_TO_STABILIZE); - - sprintf(str_buf, "%d", sample_rate); - setenv("DaqSampleRate", str_buf); - - if (sample_64x) { - setenv("Daq64xSampling", "1"); - setenv("Daq128xSampling", NULL); - } - else { - setenv("Daq64xSampling", NULL); - setenv("Daq128xSampling", "1"); - } - - /* - * Display the ADC/DAC clocking information - */ - if (!quiet) { - Daq_Display_Clocks(); - } - - /* - * Determine the DAC data justification - */ - - right_just = INITIAL_RIGHT_JUST; - if ((ep = getenv("DaqDACRightJustified")) != NULL) { - right_just = simple_strtol(ep, NULL, 10); - } - - sprintf(str_buf, "%d", right_just); - setenv("DaqDACRightJustified", str_buf); - - /* - * Determine the DAC MCLK Divide - */ - - mclk_divide = INITIAL_MCLK_DIVIDE; - if ((ep = getenv("DaqDACMClockDivide")) != NULL) { - mclk_divide = simple_strtol(ep, NULL, 10); - } - - sprintf(str_buf, "%d", mclk_divide); - setenv("DaqDACMClockDivide", str_buf); - - /* - * Initializing the I2C address in the Crystal A/Ds: - * - * 1) Wait for VREF cap to settle (10uSec per uF) - * 2) Release pullup on SDATA - * 3) Write the I2C address to register 6 - * 4) Enable address matching by setting the MSB in register 7 - */ - - if (!quiet) { - printf("Initializing the ADC...\n"); - } - udelay(ADC_INITIAL_DELAY); /* 10uSec per uF of VREF cap */ - - iopa->pdat &= ~ADC_SDATA1_MASK; /* release SDATA1 */ - udelay(ADC_SDATA_DELAY); /* arbitrary settling time */ - - i2c_reg_write(0x00, 0x06, I2C_ADC_1_ADDR); /* set address */ - i2c_reg_write(I2C_ADC_1_ADDR, 0x07, /* turn on ADDREN */ - ADC_REG7_ADDR_ENABLE); - - i2c_reg_write(I2C_ADC_1_ADDR, 0x02, /* 128x, slave mode, !HPEN */ - (sample_64x ? 0 : ADC_REG2_128x) | - ADC_REG2_HIGH_PASS_DIS | - ADC_REG2_SLAVE_MODE); - - reg = i2c_reg_read(I2C_ADC_1_ADDR, 0x06) & 0x7F; - if(reg != I2C_ADC_1_ADDR) - printf("Init of ADC U10 failed: address is 0x%02X should be 0x%02X\n", - reg, I2C_ADC_1_ADDR); - - iopa->pdat &= ~ADC_SDATA2_MASK; /* release SDATA2 */ - udelay(ADC_SDATA_DELAY); /* arbitrary settling time */ - - i2c_reg_write(0x00, 0x06, I2C_ADC_2_ADDR); /* set address (do not set ADDREN yet) */ - - i2c_reg_write(I2C_ADC_2_ADDR, 0x02, /* 64x, slave mode, !HPEN */ - (sample_64x ? 0 : ADC_REG2_128x) | - ADC_REG2_HIGH_PASS_DIS | - ADC_REG2_SLAVE_MODE); - - reg = i2c_reg_read(I2C_ADC_2_ADDR, 0x06) & 0x7F; - if(reg != I2C_ADC_2_ADDR) - printf("Init of ADC U15 failed: address is 0x%02X should be 0x%02X\n", - reg, I2C_ADC_2_ADDR); - - i2c_reg_write(I2C_ADC_1_ADDR, 0x01, /* set FSTART and GNDCAL */ - ADC_REG1_FRAME_START | - ADC_REG1_GROUND_CAL); - - i2c_reg_write(I2C_ADC_1_ADDR, 0x02, /* Start calibration */ - (sample_64x ? 0 : ADC_REG2_128x) | - ADC_REG2_CAL | - ADC_REG2_HIGH_PASS_DIS | - ADC_REG2_SLAVE_MODE); - - udelay(ADC_CAL_DELAY); /* a minimum of 4100 LRCLKs */ - i2c_reg_write(I2C_ADC_1_ADDR, 0x01, 0x00); /* remove GNDCAL */ - - /* - * Now that we have synchronized the ADC's, enable address - * selection on the second ADC as well as the first. - */ - i2c_reg_write(I2C_ADC_2_ADDR, 0x07, ADC_REG7_ADDR_ENABLE); - - /* - * Initialize the Crystal DAC - * - * Two of the config lines are used for I2C so we have to set them - * to the proper initialization state without inadvertantly - * sending an I2C "start" sequence. When we bring the I2C back to - * the normal state, we send an I2C "stop" sequence. - */ - if (!quiet) { - printf("Initializing the DAC...\n"); - } - - /* - * Bring the I2C clock and data lines low for initialization - */ - I2C_SCL(0); - I2C_DELAY; - I2C_SDA(0); - I2C_ACTIVE; - I2C_DELAY; - - /* Reset the DAC */ - iopa->pdat &= ~DAC_RST_MASK; - udelay(DAC_RESET_DELAY); - - /* Release the DAC reset */ - iopa->pdat |= DAC_RST_MASK; - udelay(DAC_INITIAL_DELAY); - - /* - * Cause the DAC to: - * Enable control port (I2C mode) - * Going into power down - */ - i2c_reg_write(I2C_DAC_ADDR, 0x05, - DAC_REG5_I2C_MODE | - DAC_REG5_POWER_DOWN); - - /* - * Cause the DAC to: - * Enable control port (I2C mode) - * Going into power down - * . MCLK divide by 1 - * . MCLK divide by 2 - */ - i2c_reg_write(I2C_DAC_ADDR, 0x05, - DAC_REG5_I2C_MODE | - DAC_REG5_POWER_DOWN | - (mclk_divide ? DAC_REG5_MCLK_DIV : 0)); - - /* - * Cause the DAC to: - * Auto-mute disabled - * . Format 0, left justified 24 bits - * . Format 3, right justified 24 bits - * No de-emphasis - * . Single speed mode - * . Double speed mode - */ - i2c_reg_write(I2C_DAC_ADDR, 0x01, - (right_just ? DAC_REG1_RIGHT_JUST_24BIT : - DAC_REG1_LEFT_JUST_24_BIT) | - DAC_REG1_DEM_NO | - (sample_rate >= 50000 ? DAC_REG1_DOUBLE : DAC_REG1_SINGLE)); - - sprintf(str_buf, "%d", - sample_rate >= 50000 ? DAC_REG1_DOUBLE : DAC_REG1_SINGLE); - setenv("DaqDACFunctionalMode", str_buf); - - /* - * Cause the DAC to: - * Enable control port (I2C mode) - * Remove power down - * . MCLK divide by 1 - * . MCLK divide by 2 - */ - i2c_reg_write(I2C_DAC_ADDR, 0x05, - DAC_REG5_I2C_MODE | - (mclk_divide ? DAC_REG5_MCLK_DIV : 0)); - - /* - * Create a I2C stop condition: - * low->high on data while clock is high. - */ - I2C_SCL(1); - I2C_DELAY; - I2C_SDA(1); - I2C_DELAY; - I2C_TRISTATE; - - if (!quiet) { - printf("\n"); - } + i2c_reg_write(I2C_ADC_1_ADDR, 0x01, /* set FSTART and GNDCAL */ + ADC_REG1_FRAME_START | ADC_REG1_GROUND_CAL); + + i2c_reg_write(I2C_ADC_1_ADDR, 0x02, /* Start calibration */ + (sample_64x ? 0 : ADC_REG2_128x) | + ADC_REG2_CAL | + ADC_REG2_HIGH_PASS_DIS | ADC_REG2_SLAVE_MODE); + + udelay(ADC_CAL_DELAY); /* a minimum of 4100 LRCLKs */ + i2c_reg_write(I2C_ADC_1_ADDR, 0x01, 0x00); /* remove GNDCAL */ + + /* + * Now that we have synchronized the ADC's, enable address + * selection on the second ADC as well as the first. + */ + i2c_reg_write(I2C_ADC_2_ADDR, 0x07, ADC_REG7_ADDR_ENABLE); + + /* + * Initialize the Crystal DAC + * + * Two of the config lines are used for I2C so we have to set them + * to the proper initialization state without inadvertantly + * sending an I2C "start" sequence. When we bring the I2C back to + * the normal state, we send an I2C "stop" sequence. + */ + if (!quiet) + printf("Initializing the DAC...\n"); + + /* + * Bring the I2C clock and data lines low for initialization + */ + I2C_SCL(0); + I2C_DELAY; + I2C_SDA(0); + I2C_ACTIVE; + I2C_DELAY; + + /* Reset the DAC */ + iopa->pdat &= ~DAC_RST_MASK; + udelay(DAC_RESET_DELAY); + + /* Release the DAC reset */ + iopa->pdat |= DAC_RST_MASK; + udelay(DAC_INITIAL_DELAY); + + /* + * Cause the DAC to: + * Enable control port (I2C mode) + * Going into power down + */ + i2c_reg_write(I2C_DAC_ADDR, 0x05, + DAC_REG5_I2C_MODE | DAC_REG5_POWER_DOWN); + + /* + * Cause the DAC to: + * Enable control port (I2C mode) + * Going into power down + * . MCLK divide by 1 + * . MCLK divide by 2 + */ + i2c_reg_write(I2C_DAC_ADDR, 0x05, + DAC_REG5_I2C_MODE | + DAC_REG5_POWER_DOWN | + (mclk_divide ? DAC_REG5_MCLK_DIV : 0)); + + /* + * Cause the DAC to: + * Auto-mute disabled + * . Format 0, left justified 24 bits + * . Format 3, right justified 24 bits + * No de-emphasis + * . Single speed mode + * . Double speed mode + */ + i2c_reg_write(I2C_DAC_ADDR, 0x01, + (right_just ? DAC_REG1_RIGHT_JUST_24BIT : + DAC_REG1_LEFT_JUST_24_BIT) | + DAC_REG1_DEM_NO | + (sample_rate >= + 50000 ? DAC_REG1_DOUBLE : DAC_REG1_SINGLE)); + + sprintf(str_buf, "%d", + sample_rate >= 50000 ? DAC_REG1_DOUBLE : DAC_REG1_SINGLE); + setenv("DaqDACFunctionalMode", str_buf); + + /* + * Cause the DAC to: + * Enable control port (I2C mode) + * Remove power down + * . MCLK divide by 1 + * . MCLK divide by 2 + */ + i2c_reg_write(I2C_DAC_ADDR, 0x05, + DAC_REG5_I2C_MODE | + (mclk_divide ? DAC_REG5_MCLK_DIV : 0)); + + /* + * Create a I2C stop condition: + * low->high on data while clock is high. + */ + I2C_SCL(1); + I2C_DELAY; + I2C_SDA(1); + I2C_DELAY; + I2C_TRISTATE; + + if (!quiet) + printf("\n"); #ifdef CONFIG_ETHER_LOOPBACK_TEST - /* - * Run the Ethernet loopback test - */ - eth_loopback_test (); + /* + * Run the Ethernet loopback test + */ + eth_loopback_test(); #endif /* CONFIG_ETHER_LOOPBACK_TEST */ #ifdef CONFIG_SHOW_BOOT_PROGRESS - /* - * Turn off the RED fail LED now that we are up and running. - */ - status_led_set(STATUS_LED_RED, STATUS_LED_OFF); + /* + * Turn off the RED fail LED now that we are up and running. + */ + status_led_set(STATUS_LED_RED, STATUS_LED_OFF); #endif - return 0; + return 0; } #ifdef CONFIG_SHOW_BOOT_PROGRESS @@ -749,85 +743,86 @@ int misc_init_r(void) */ static void flash_code(uchar number, uchar modulo, uchar digits) { - int j; - - /* - * Recursively do upper digits. - */ - if(digits > 1) { - flash_code(number / modulo, modulo, digits - 1); - } - - number = number % modulo; - - /* - * Zero is indicated by one long flash (dash). - */ - if(number == 0) { - status_led_set(STATUS_LED_BOOT, STATUS_LED_ON); - udelay(1000000); - status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF); - udelay(200000); - } else { - /* - * Non-zero is indicated by short flashes, one per count. - */ - for(j = 0; j < number; j++) { - status_led_set(STATUS_LED_BOOT, STATUS_LED_ON); - udelay(100000); - status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF); - udelay(200000); - } - } - /* - * Inter-digit pause: we've already waited 200 mSec, wait 1 sec total - */ - udelay(700000); -} - -static int last_boot_progress; + int j; -void show_boot_progress (int status) -{ - int i,j; - if(status > 0) { - last_boot_progress = status; - } else { /* - * If a specific failure code is given, flash this code - * else just use the last success code we've seen + * Recursively do upper digits. */ - if(status < -1) - last_boot_progress = -status; + if (digits > 1) + flash_code(number / modulo, modulo, digits - 1); + + number = number % modulo; /* - * Flash this code 5 times + * Zero is indicated by one long flash (dash). */ - for(j=0; j<5; j++) { - /* - * Houston, we have a problem. - * Blink the last OK status which indicates where things failed. - */ - status_led_set(STATUS_LED_RED, STATUS_LED_ON); - flash_code(last_boot_progress, 5, 3); - - /* - * Delay 5 seconds between repetitions, - * with the fault LED blinking - */ - for(i=0; i<5; i++) { - status_led_set(STATUS_LED_RED, STATUS_LED_OFF); - udelay(500000); - status_led_set(STATUS_LED_RED, STATUS_LED_ON); - udelay(500000); - } + if (number == 0) { + status_led_set(STATUS_LED_BOOT, STATUS_LED_ON); + udelay(1000000); + status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF); + udelay(200000); + } else { + /* + * Non-zero is indicated by short flashes, one per count. + */ + for (j = 0; j < number; j++) { + status_led_set(STATUS_LED_BOOT, STATUS_LED_ON); + udelay(100000); + status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF); + udelay(200000); + } } - /* - * Reset the board to retry initialization. + * Inter-digit pause: we've already waited 200 mSec, wait 1 sec total */ - do_reset (NULL, 0, 0, NULL); - } + udelay(700000); +} + +static int last_boot_progress; + +void show_boot_progress(int status) +{ + int i, j; + + if (status > 0) { + last_boot_progress = status; + } else { + /* + * If a specific failure code is given, flash this code + * else just use the last success code we've seen + */ + if (status < -1) + last_boot_progress = -status; + + /* + * Flash this code 5 times + */ + for (j = 0; j < 5; j++) { + /* + * Houston, we have a problem. + * Blink the last OK status which indicates where things failed. + */ + status_led_set(STATUS_LED_RED, STATUS_LED_ON); + flash_code(last_boot_progress, 5, 3); + + /* + * Delay 5 seconds between repetitions, + * with the fault LED blinking + */ + for (i = 0; i < 5; i++) { + status_led_set(STATUS_LED_RED, + STATUS_LED_OFF); + udelay(500000); + status_led_set(STATUS_LED_RED, STATUS_LED_ON); + udelay(500000); + } + } + + /* + * Reset the board to retry initialization. + */ + do_reset(NULL, 0, 0, NULL); + } } #endif /* CONFIG_SHOW_BOOT_PROGRESS */ @@ -841,27 +836,29 @@ void show_boot_progress (int status) #define SPI_DAC_CS_MASK 0x00001000 static const u32 cs_mask[] = { - SPI_ADC_CS_MASK, - SPI_DAC_CS_MASK, + SPI_ADC_CS_MASK, + SPI_DAC_CS_MASK, }; int spi_cs_is_valid(unsigned int bus, unsigned int cs) { - return bus == 0 && cs < sizeof(cs_mask) / sizeof(cs_mask[0]); + return bus == 0 && cs < sizeof(cs_mask) / sizeof(cs_mask[0]); } void spi_cs_activate(struct spi_slave *slave) { - volatile ioport_t *iopd = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3 /* port D */); + volatile ioport_t *iopd = + ioport_addr((immap_t *) CONFIG_SYS_IMMR, 3 /* port D */ ); - iopd->pdat &= ~cs_mask[slave->cs]; + iopd->pdat &= ~cs_mask[slave->cs]; } void spi_cs_deactivate(struct spi_slave *slave) { - volatile ioport_t *iopd = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3 /* port D */); + volatile ioport_t *iopd = + ioport_addr((immap_t *) CONFIG_SYS_IMMR, 3 /* port D */ ); - iopd->pdat |= cs_mask[slave->cs]; + iopd->pdat |= cs_mask[slave->cs]; } #endif