From: goda.yusuke Date: Wed, 5 Mar 2008 08:08:20 +0000 (+0900) Subject: net: Divided code of NE2000 ethernet driver X-Git-Tag: v1.3.3-rc1~182 X-Git-Url: https://git.sur5r.net/?a=commitdiff_plain;h=e710185aae90c64d39c2d453e40e58ceefe4f250;p=u-boot net: Divided code of NE2000 ethernet driver There are more devices of the NE2000 base. A present code is difficult for us to support more devices. To support more NE2000 clone devices, separated the function. Signed-off-by: Yusuke Goda Acked-by: Nobuhiro Iwamatsu --- diff --git a/drivers/net/ne2000.c b/drivers/net/ne2000.c index b100657539..49280148d2 100644 --- a/drivers/net/ne2000.c +++ b/drivers/net/ne2000.c @@ -82,25 +82,11 @@ Add SNMP #ifdef CONFIG_DRIVER_NE2000 -/* wor around udelay resetting OCR */ -static void my_udelay(long us) { - long tmo; - - tmo = get_timer (0) + us * CFG_HZ / 1000000; /* will this be much greater than 0 ? */ - while (get_timer (0) < tmo); -} - -#define mdelay(n) my_udelay((n)*1000) - +#define mdelay(n) udelay((n)*1000) /* forward definition of function used for the uboot interface */ void uboot_push_packet_len(int len); void uboot_push_tx_done(int key, int val); -/* timeout for tx/rx in s */ -#define TOUT 5 - -#define ETHER_ADDR_LEN 6 - /* ------------------------------------------------------------------------ Debugging details @@ -118,18 +104,18 @@ void uboot_push_tx_done(int key, int val); #if DEBUG & 1 #define DEBUG_FUNCTION() do { printf("%s\n", __FUNCTION__); } while (0) #define DEBUG_LINE() do { printf("%d\n", __LINE__); } while (0) +#define PRINTK(args...) printf(args) #else #define DEBUG_FUNCTION() do {} while(0) #define DEBUG_LINE() do {} while(0) +#define PRINTK(args...) #endif -#include "ne2000.h" +/* NE2000 base header file */ +#include "ne2000_base.h" -#if DEBUG & 1 -#define PRINTK(args...) printf(args) -#else -#define PRINTK(args...) -#endif +/* Basic NE2000 chip support */ +#include "ne2000.h" static dp83902a_priv_data_t nic; /* just one instance of the card supported */ @@ -137,8 +123,7 @@ static bool dp83902a_init(void) { dp83902a_priv_data_t *dp = &nic; - cyg_uint8* base; - int i; + u8* base; DEBUG_FUNCTION(); @@ -147,6 +132,7 @@ dp83902a_init(void) DEBUG_LINE(); +#if defined(NE2000_BASIC_INIT) /* Prepare ESA */ DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1); /* Select page 1 */ /* Use the address from the serial EEPROM */ @@ -163,6 +149,7 @@ dp83902a_init(void) dp->esa[4], dp->esa[5] ); +#endif /* NE2000_BASIC_INIT */ return true; } @@ -170,7 +157,7 @@ static void dp83902a_stop(void) { dp83902a_priv_data_t *dp = &nic; - cyg_uint8 *base = dp->base; + u8 *base = dp->base; DEBUG_FUNCTION(); @@ -188,10 +175,10 @@ dp83902a_stop(void) the hardware ready to send/receive packets. */ static void -dp83902a_start(unsigned char * enaddr) +dp83902a_start(u8 * enaddr) { dp83902a_priv_data_t *dp = &nic; - cyg_uint8 *base = dp->base; + u8 *base = dp->base; int i; DEBUG_FUNCTION(); @@ -206,15 +193,20 @@ dp83902a_start(unsigned char * enaddr) dp->tx1 = dp->tx2 = 0; dp->tx_next = dp->tx_buf1; dp->tx_started = false; + dp->running = true; DP_OUT(base, DP_PSTART, dp->rx_buf_start); /* Receive ring start page */ DP_OUT(base, DP_BNDRY, dp->rx_buf_end-1); /* Receive ring boundary */ DP_OUT(base, DP_PSTOP, dp->rx_buf_end); /* Receive ring end page */ dp->rx_next = dp->rx_buf_start-1; + dp->running = true; DP_OUT(base, DP_ISR, 0xFF); /* Clear any pending interrupts */ DP_OUT(base, DP_IMR, DP_IMR_All); /* Enable all interrupts */ DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1 | DP_CR_STOP); /* Select page 1 */ DP_OUT(base, DP_P1_CURP, dp->rx_buf_start); /* Current page - next free page for Rx */ + dp->running = true; for (i = 0; i < ETHER_ADDR_LEN; i++) { + /* FIXME */ + //*((vu_short*)( base + ((DP_P1_PAR0 + i) * 2) + 0x1400)) = enaddr[i]; DP_OUT(base, DP_P1_PAR0+i, enaddr[i]); } /* Enable and start device */ @@ -222,6 +214,7 @@ dp83902a_start(unsigned char * enaddr) DP_OUT(base, DP_TCR, DP_TCR_NORMAL); /* Normal transmit operations */ DP_OUT(base, DP_RCR, DP_RCR_AB); /* Accept broadcast, no errors, no multicast */ dp->running = true; + } /* @@ -234,7 +227,7 @@ static void dp83902a_start_xmit(int start_page, int len) { dp83902a_priv_data_t *dp = (dp83902a_priv_data_t *) &nic; - cyg_uint8 *base = dp->base; + u8 *base = dp->base; DEBUG_FUNCTION(); @@ -259,10 +252,10 @@ dp83902a_start_xmit(int start_page, int len) that there is free buffer space (dp->tx_next). */ static void -dp83902a_send(unsigned char *data, int total_len, unsigned long key) +dp83902a_send(u8 *data, int total_len, u32 key) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; + u8 *base = dp->base; int len, start_page, pkt_len, i, isr; #if DEBUG & 4 int dx; @@ -296,7 +289,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key) /* but the code is extended a bit to do what Hitachi's monitor */ /* does (i.e., also read data). */ - cyg_uint16 tmp; + u16 tmp; int len = 1; DP_OUT(base, DP_RSAL, 0x100-len); @@ -322,7 +315,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key) /* Put data into buffer */ #if DEBUG & 4 - printf(" sg buf %08lx len %08x\n ", (unsigned long) data, len); + printf(" sg buf %08lx len %08x\n ", (u32)data, len); dx = 0; #endif while (len > 0) { @@ -330,6 +323,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key) printf(" %02x", *data); if (0 == (++dx % 16)) printf("\n "); #endif + DP_OUT_DATA(dp->data, *data++); len--; } @@ -358,6 +352,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key) do { DP_IN(base, DP_ISR, isr); } while ((isr & DP_ISR_RDC) == 0); + /* Then disable DMA */ DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); @@ -383,9 +378,9 @@ static void dp83902a_RxEvent(void) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; - unsigned char rsr; - unsigned char rcv_hdr[4]; + u8 *base = dp->base; + u8 rsr; + u8 rcv_hdr[4]; int i, len, pkt, cur; DEBUG_FUNCTION(); @@ -423,6 +418,7 @@ dp83902a_RxEvent(void) CYGACC_CALL_IF_DELAY_US(10); #endif + /* read header (get data size)*/ for (i = 0; i < sizeof(rcv_hdr);) { DP_IN_DATA(dp->data, rcv_hdr[i++]); } @@ -432,7 +428,10 @@ dp83902a_RxEvent(void) rcv_hdr[0], rcv_hdr[1], rcv_hdr[2], rcv_hdr[3]); #endif len = ((rcv_hdr[3] << 8) | rcv_hdr[2]) - sizeof(rcv_hdr); + + /* data read */ uboot_push_packet_len(len); + if (rcv_hdr[1] == dp->rx_buf_start) DP_OUT(base, DP_BNDRY, dp->rx_buf_end-1); else @@ -448,12 +447,12 @@ dp83902a_RxEvent(void) efficient processing in the upper layers of the stack. */ static void -dp83902a_recv(unsigned char *data, int len) +dp83902a_recv(u8 *data, int len) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; + u8 *base = dp->base; int i, mlen; - cyg_uint8 saved_char = 0; + u8 saved_char = 0; bool saved; #if DEBUG & 4 int dx; @@ -482,7 +481,7 @@ dp83902a_recv(unsigned char *data, int len) if (data) { mlen = len; #if DEBUG & 4 - printf(" sg buf %08lx len %08x \n", (unsigned long) data, mlen); + printf(" sg buf %08lx len %08x \n", (u32) data, mlen); dx = 0; #endif while (0 < mlen) { @@ -495,7 +494,7 @@ dp83902a_recv(unsigned char *data, int len) } { - cyg_uint8 tmp; + u8 tmp; DP_IN_DATA(dp->data, tmp); #if DEBUG & 4 printf(" %02x", tmp); @@ -516,9 +515,9 @@ static void dp83902a_TxEvent(void) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; - unsigned char tsr; - unsigned long key; + u8 *base = dp->base; + u8 tsr; + u32 key; DEBUG_FUNCTION(); @@ -551,8 +550,8 @@ static void dp83902a_ClearCounters(void) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; - cyg_uint8 cnt1, cnt2, cnt3; + u8 *base = dp->base; + u8 cnt1, cnt2, cnt3; DP_IN(base, DP_FER, cnt1); DP_IN(base, DP_CER, cnt2); @@ -566,8 +565,8 @@ static void dp83902a_Overflow(void) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *)&nic; - cyg_uint8 *base = dp->base; - cyg_uint8 isr; + u8 *base = dp->base; + u8 isr; /* Issue a stop command and wait 1.6ms for it to complete. */ DP_OUT(base, DP_CR, DP_CR_STOP | DP_CR_NODMA); @@ -603,8 +602,8 @@ static void dp83902a_poll(void) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; - unsigned char isr; + u8 *base = dp->base; + u8 isr; DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE0 | DP_CR_START); DP_IN(base, DP_ISR, isr); @@ -642,13 +641,13 @@ dp83902a_poll(void) /* find prom (taken from pc_net_cs.c from Linux) */ #include "8390.h" - +/* typedef struct hw_info_t { u_int offset; u_char a0, a1, a2; u_int flags; } hw_info_t; - +*/ #define DELAY_OUTPUT 0x01 #define HAS_MISC_REG 0x02 #define USE_BIG_BUF 0x04 @@ -731,102 +730,17 @@ static hw_info_t hw_info[] = { static hw_info_t default_info = { 0, 0, 0, 0, 0 }; -unsigned char dev_addr[6]; +u8 dev_addr[6]; #define PCNET_CMD 0x00 #define PCNET_DATAPORT 0x10 /* NatSemi-defined port window offset. */ #define PCNET_RESET 0x1f /* Issue a read to reset, a write to clear. */ #define PCNET_MISC 0x18 /* For IBM CCAE and Socket EA cards */ -unsigned long nic_base; - -static void pcnet_reset_8390(void) -{ - int i, r; - - PRINTK("nic base is %lx\n", nic_base); - - n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); - PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); - n2k_outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, E8390_CMD); - PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); - n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); - PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); - n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); - - n2k_outb(n2k_inb(PCNET_RESET), PCNET_RESET); - - for (i = 0; i < 100; i++) { - if ((r = (n2k_inb(EN0_ISR) & ENISR_RESET)) != 0) - break; - PRINTK("got %x in reset\n", r); - my_udelay(100); - } - n2k_outb(ENISR_RESET, EN0_ISR); /* Ack intr. */ - - if (i == 100) - printf("pcnet_reset_8390() did not complete.\n"); -} /* pcnet_reset_8390 */ - -static hw_info_t * get_prom(void ) { - unsigned char prom[32]; - int i, j; - struct { - u_char value, offset; - } program_seq[] = { - {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/ - {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */ - {0x00, EN0_RCNTLO}, /* Clear the count regs. */ - {0x00, EN0_RCNTHI}, - {0x00, EN0_IMR}, /* Mask completion irq. */ - {0xFF, EN0_ISR}, - {E8390_RXOFF, EN0_RXCR}, /* 0x20 Set to monitor */ - {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */ - {32, EN0_RCNTLO}, - {0x00, EN0_RCNTHI}, - {0x00, EN0_RSARLO}, /* DMA starting at 0x0000. */ - {0x00, EN0_RSARHI}, - {E8390_RREAD+E8390_START, E8390_CMD}, - }; - - PRINTK("trying to get MAC via prom reading\n"); - - pcnet_reset_8390(); - - mdelay(10); - - for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++) - n2k_outb(program_seq[i].value, program_seq[i].offset); - - PRINTK("PROM:"); - for (i = 0; i < 32; i++) { - prom[i] = n2k_inb(PCNET_DATAPORT); - PRINTK(" %02x", prom[i]); - } - PRINTK("\n"); - for (i = 0; i < NR_INFO; i++) { - if ((prom[0] == hw_info[i].a0) && - (prom[2] == hw_info[i].a1) && - (prom[4] == hw_info[i].a2)) { - PRINTK("matched board %d\n", i); - break; - } - } - if ((i < NR_INFO) || ((prom[28] == 0x57) && (prom[30] == 0x57))) { - for (j = 0; j < 6; j++) - dev_addr[j] = prom[j<<1]; - PRINTK("on exit i is %d/%ld\n", i, NR_INFO); - PRINTK("MAC address is %02x:%02x:%02x:%02x:%02x:%02x\n", - dev_addr[0],dev_addr[1],dev_addr[2],dev_addr[3],dev_addr[4],dev_addr[5]); - return (i < NR_INFO) ? hw_info+i : &default_info; - } - return NULL; -} +u32 nic_base; /* U-boot specific routines */ - - -static unsigned char *pbuf = NULL; +static u8 *pbuf = NULL; static int pkey = -1; static int initialized=0; @@ -839,7 +753,7 @@ void uboot_push_packet_len(int len) { } dp83902a_recv(&pbuf[0], len); - /* Just pass it to the upper layer */ + /*Just pass it to the upper layer*/ NetReceive(&pbuf[0], len); } @@ -864,7 +778,7 @@ int eth_init(bd_t *bd) { #ifdef CONFIG_DRIVER_NE2000_CCR { - volatile unsigned char *p = (volatile unsigned char *) CONFIG_DRIVER_NE2000_CCR; + vu_char *p = (vu_char *) CONFIG_DRIVER_NE2000_CCR; PRINTK("CCR before is %x\n", *p); *p = CONFIG_DRIVER_NE2000_VAL; @@ -873,9 +787,9 @@ int eth_init(bd_t *bd) { #endif nic_base = CONFIG_DRIVER_NE2000_BASE; - nic.base = (cyg_uint8 *) CONFIG_DRIVER_NE2000_BASE; + nic.base = (u8 *) CONFIG_DRIVER_NE2000_BASE; - r = get_prom(); + r = get_prom(dev_addr); if (!r) return -1; @@ -886,22 +800,23 @@ int eth_init(bd_t *bd) { PRINTK("Set environment from HW MAC addr = \"%s\"\n", ethaddr); setenv ("ethaddr", ethaddr); - -#define DP_DATA 0x10 nic.data = nic.base + DP_DATA; - nic.tx_buf1 = 0x40; - nic.tx_buf2 = 0x48; - nic.rx_buf_start = 0x50; - nic.rx_buf_end = 0x80; + nic.tx_buf1 = START_PG; + nic.tx_buf2 = START_PG2; + nic.rx_buf_start = RX_START; + nic.rx_buf_end = RX_END; if (dp83902a_init() == false) return -1; + dp83902a_start(dev_addr); initialized=1; + return 0; } void eth_halt() { + PRINTK("### eth_halt\n"); if(initialized) dp83902a_stop(); @@ -920,7 +835,7 @@ int eth_send(volatile void *packet, int length) { pkey = -1; - dp83902a_send((unsigned char *) packet, length, 666); + dp83902a_send((u8 *) packet, length, 666); tmo = get_timer (0) + TOUT * CFG_HZ; while(1) { dp83902a_poll(); diff --git a/drivers/net/ne2000.h b/drivers/net/ne2000.h index c13d9f0bbb..06e9a2844e 100644 --- a/drivers/net/ne2000.h +++ b/drivers/net/ne2000.h @@ -71,209 +71,113 @@ are GPL, so this is, of course, GPL. */ /* - ------------------------------------------------------------------------ - Macros for accessing DP registers - These can be overridden by the platform header -*/ - -#define DP_IN(_b_, _o_, _d_) (_d_) = *( (volatile unsigned char *) ((_b_)+(_o_))) -#define DP_OUT(_b_, _o_, _d_) *( (volatile unsigned char *) ((_b_)+(_o_))) = (_d_) - -#define DP_IN_DATA(_b_, _d_) (_d_) = *( (volatile unsigned char *) ((_b_))) -#define DP_OUT_DATA(_b_, _d_) *( (volatile unsigned char *) ((_b_))) = (_d_) - - -/* here is all the data */ - -#define cyg_uint8 unsigned char -#define cyg_uint16 unsigned short -#define bool int - -#define false 0 -#define true 1 - -#define CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA 1 -#define CYGACC_CALL_IF_DELAY_US(X) my_udelay(X) - -typedef struct dp83902a_priv_data { - cyg_uint8* base; - cyg_uint8* data; - cyg_uint8* reset; - int tx_next; /* First free Tx page */ - int tx_int; /* Expecting interrupt from this buffer */ - int rx_next; /* First free Rx page */ - int tx1, tx2; /* Page numbers for Tx buffers */ - unsigned long tx1_key, tx2_key; /* Used to ack when packet sent */ - int tx1_len, tx2_len; - bool tx_started, running, hardwired_esa; - cyg_uint8 esa[6]; - void* plf_priv; - - /* Buffer allocation */ - int tx_buf1, tx_buf2; - int rx_buf_start, rx_buf_end; -} dp83902a_priv_data_t; - -/* - ------------------------------------------------------------------------ - Some forward declarations -*/ -static void dp83902a_poll(void); - -/* ------------------------------------------------------------------------ */ -/* Register offsets */ - -#define DP_CR 0x00 -#define DP_CLDA0 0x01 -#define DP_PSTART 0x01 /* write */ -#define DP_CLDA1 0x02 -#define DP_PSTOP 0x02 /* write */ -#define DP_BNDRY 0x03 -#define DP_TSR 0x04 -#define DP_TPSR 0x04 /* write */ -#define DP_NCR 0x05 -#define DP_TBCL 0x05 /* write */ -#define DP_FIFO 0x06 -#define DP_TBCH 0x06 /* write */ -#define DP_ISR 0x07 -#define DP_CRDA0 0x08 -#define DP_RSAL 0x08 /* write */ -#define DP_CRDA1 0x09 -#define DP_RSAH 0x09 /* write */ -#define DP_RBCL 0x0a /* write */ -#define DP_RBCH 0x0b /* write */ -#define DP_RSR 0x0c -#define DP_RCR 0x0c /* write */ -#define DP_FER 0x0d -#define DP_TCR 0x0d /* write */ -#define DP_CER 0x0e -#define DP_DCR 0x0e /* write */ -#define DP_MISSED 0x0f -#define DP_IMR 0x0f /* write */ -#define DP_DATAPORT 0x10 /* "eprom" data port */ - -#define DP_P1_CR 0x00 -#define DP_P1_PAR0 0x01 -#define DP_P1_PAR1 0x02 -#define DP_P1_PAR2 0x03 -#define DP_P1_PAR3 0x04 -#define DP_P1_PAR4 0x05 -#define DP_P1_PAR5 0x06 -#define DP_P1_CURP 0x07 -#define DP_P1_MAR0 0x08 -#define DP_P1_MAR1 0x09 -#define DP_P1_MAR2 0x0a -#define DP_P1_MAR3 0x0b -#define DP_P1_MAR4 0x0c -#define DP_P1_MAR5 0x0d -#define DP_P1_MAR6 0x0e -#define DP_P1_MAR7 0x0f - -#define DP_P2_CR 0x00 -#define DP_P2_PSTART 0x01 -#define DP_P2_CLDA0 0x01 /* write */ -#define DP_P2_PSTOP 0x02 -#define DP_P2_CLDA1 0x02 /* write */ -#define DP_P2_RNPP 0x03 -#define DP_P2_TPSR 0x04 -#define DP_P2_LNPP 0x05 -#define DP_P2_ACH 0x06 -#define DP_P2_ACL 0x07 -#define DP_P2_RCR 0x0c -#define DP_P2_TCR 0x0d -#define DP_P2_DCR 0x0e -#define DP_P2_IMR 0x0f - -/* Command register - common to all pages */ - -#define DP_CR_STOP 0x01 /* Stop: software reset */ -#define DP_CR_START 0x02 /* Start: initialize device */ -#define DP_CR_TXPKT 0x04 /* Transmit packet */ -#define DP_CR_RDMA 0x08 /* Read DMA (recv data from device) */ -#define DP_CR_WDMA 0x10 /* Write DMA (send data to device) */ -#define DP_CR_SEND 0x18 /* Send packet */ -#define DP_CR_NODMA 0x20 /* Remote (or no) DMA */ -#define DP_CR_PAGE0 0x00 /* Page select */ -#define DP_CR_PAGE1 0x40 -#define DP_CR_PAGE2 0x80 -#define DP_CR_PAGEMSK 0x3F /* Used to mask out page bits */ - -/* Data configuration register */ - -#define DP_DCR_WTS 0x01 /* 1=16 bit word transfers */ -#define DP_DCR_BOS 0x02 /* 1=Little Endian */ -#define DP_DCR_LAS 0x04 /* 1=Single 32 bit DMA mode */ -#define DP_DCR_LS 0x08 /* 1=normal mode, 0=loopback */ -#define DP_DCR_ARM 0x10 /* 0=no send command (program I/O) */ -#define DP_DCR_FIFO_1 0x00 /* FIFO threshold */ -#define DP_DCR_FIFO_2 0x20 -#define DP_DCR_FIFO_4 0x40 -#define DP_DCR_FIFO_6 0x60 - -#define DP_DCR_INIT (DP_DCR_LS|DP_DCR_FIFO_4) - -/* Interrupt status register */ - -#define DP_ISR_RxP 0x01 /* Packet received */ -#define DP_ISR_TxP 0x02 /* Packet transmitted */ -#define DP_ISR_RxE 0x04 /* Receive error */ -#define DP_ISR_TxE 0x08 /* Transmit error */ -#define DP_ISR_OFLW 0x10 /* Receive overflow */ -#define DP_ISR_CNT 0x20 /* Tally counters need emptying */ -#define DP_ISR_RDC 0x40 /* Remote DMA complete */ -#define DP_ISR_RESET 0x80 /* Device has reset (shutdown, error) */ - -/* Interrupt mask register */ - -#define DP_IMR_RxP 0x01 /* Packet received */ -#define DP_IMR_TxP 0x02 /* Packet transmitted */ -#define DP_IMR_RxE 0x04 /* Receive error */ -#define DP_IMR_TxE 0x08 /* Transmit error */ -#define DP_IMR_OFLW 0x10 /* Receive overflow */ -#define DP_IMR_CNT 0x20 /* Tall counters need emptying */ -#define DP_IMR_RDC 0x40 /* Remote DMA complete */ - -#define DP_IMR_All 0x3F /* Everything but remote DMA */ - -/* Receiver control register */ - -#define DP_RCR_SEP 0x01 /* Save bad(error) packets */ -#define DP_RCR_AR 0x02 /* Accept runt packets */ -#define DP_RCR_AB 0x04 /* Accept broadcast packets */ -#define DP_RCR_AM 0x08 /* Accept multicast packets */ -#define DP_RCR_PROM 0x10 /* Promiscuous mode */ -#define DP_RCR_MON 0x20 /* Monitor mode - 1=accept no packets */ - -/* Receiver status register */ - -#define DP_RSR_RxP 0x01 /* Packet received */ -#define DP_RSR_CRC 0x02 /* CRC error */ -#define DP_RSR_FRAME 0x04 /* Framing error */ -#define DP_RSR_FO 0x08 /* FIFO overrun */ -#define DP_RSR_MISS 0x10 /* Missed packet */ -#define DP_RSR_PHY 0x20 /* 0=pad match, 1=mad match */ -#define DP_RSR_DIS 0x40 /* Receiver disabled */ -#define DP_RSR_DFR 0x80 /* Receiver processing deferred */ - -/* Transmitter control register */ - -#define DP_TCR_NOCRC 0x01 /* 1=inhibit CRC */ -#define DP_TCR_NORMAL 0x00 /* Normal transmitter operation */ -#define DP_TCR_LOCAL 0x02 /* Internal NIC loopback */ -#define DP_TCR_INLOOP 0x04 /* Full internal loopback */ -#define DP_TCR_OUTLOOP 0x08 /* External loopback */ -#define DP_TCR_ATD 0x10 /* Auto transmit disable */ -#define DP_TCR_OFFSET 0x20 /* Collision offset adjust */ - -/* Transmit status register */ - -#define DP_TSR_TxP 0x01 /* Packet transmitted */ -#define DP_TSR_COL 0x04 /* Collision (at least one) */ -#define DP_TSR_ABT 0x08 /* Aborted because of too many collisions */ -#define DP_TSR_CRS 0x10 /* Lost carrier */ -#define DP_TSR_FU 0x20 /* FIFO underrun */ -#define DP_TSR_CDH 0x40 /* Collision Detect Heartbeat */ -#define DP_TSR_OWC 0x80 /* Collision outside normal window */ - -#define IEEE_8023_MAX_FRAME 1518 /* Largest possible ethernet frame */ -#define IEEE_8023_MIN_FRAME 64 /* Smallest possible ethernet frame */ + * NE2000 support header file. + * Created by Nobuhiro Iwamatsu + */ + +#ifndef __DRIVERS_NE2000_H__ +#define __DRIVERS_NE2000_H__ + +/* Enable NE2000 basic init function */ +#define NE2000_BASIC_INIT + +#define DP_DATA 0x10 +#define START_PG 0x50 /* First page of TX buffer */ +#define STOP_PG 0x80 /* Last page +1 of RX ring */ + +#define RX_START 0x50 +#define RX_END 0x80 + +#define DP_IN(_b_, _o_, _d_) (_d_) = *( (vu_char *) ((_b_)+(_o_))) +#define DP_OUT(_b_, _o_, _d_) *( (vu_char *) ((_b_)+(_o_))) = (_d_) +#define DP_IN_DATA(_b_, _d_) (_d_) = *( (vu_char *) ((_b_))) +#define DP_OUT_DATA(_b_, _d_) *( (vu_char *) ((_b_))) = (_d_) + +static void pcnet_reset_8390(void) +{ + int i, r; + + PRINTK("nic base is %lx\n", nic_base); + + n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); + PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); + n2k_outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, E8390_CMD); + PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); + n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); + PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); + n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); + + n2k_outb(n2k_inb(PCNET_RESET), PCNET_RESET); + + for (i = 0; i < 100; i++) { + if ((r = (n2k_inb(EN0_ISR) & ENISR_RESET)) != 0) + break; + PRINTK("got %x in reset\n", r); + udelay(100); + } + n2k_outb(ENISR_RESET, EN0_ISR); /* Ack intr. */ + + if (i == 100) + printf("pcnet_reset_8390() did not complete.\n"); +} /* pcnet_reset_8390 */ + +int get_prom(u8* mac_addr) +{ + u8 prom[32]; + int i, j; + struct { + u_char value, offset; + } program_seq[] = { + {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/ + {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */ + {0x00, EN0_RCNTLO}, /* Clear the count regs. */ + {0x00, EN0_RCNTHI}, + {0x00, EN0_IMR}, /* Mask completion irq. */ + {0xFF, EN0_ISR}, + {E8390_RXOFF, EN0_RXCR}, /* 0x20 Set to monitor */ + {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */ + {32, EN0_RCNTLO}, + {0x00, EN0_RCNTHI}, + {0x00, EN0_RSARLO}, /* DMA starting at 0x0000. */ + {0x00, EN0_RSARHI}, + {E8390_RREAD+E8390_START, E8390_CMD}, + }; + + PRINTK("trying to get MAC via prom reading\n"); + + pcnet_reset_8390(); + + mdelay(10); + + for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++) + n2k_outb(program_seq[i].value, program_seq[i].offset); + + PRINTK("PROM:"); + for (i = 0; i < 32; i++) { + prom[i] = n2k_inb(PCNET_DATAPORT); + PRINTK(" %02x", prom[i]); + } + PRINTK("\n"); + for (i = 0; i < NR_INFO; i++) { + if ((prom[0] == hw_info[i].a0) && + (prom[2] == hw_info[i].a1) && + (prom[4] == hw_info[i].a2)) { + PRINTK("matched board %d\n", i); + break; + } + } + if ((i < NR_INFO) || ((prom[28] == 0x57) && (prom[30] == 0x57))) { + PRINTK("on exit i is %d/%ld\n", i, NR_INFO); + PRINTK("MAC address is "); + for (j = 0; j < 6; j++){ + mac_addr[j] = prom[j<<1]; + PRINTK("%02x:",mac_addr[i]); + } + PRINTK("\n"); + return (i < NR_INFO) ? i : 0; + } + return NULL; +} + + +#endif /* __DRIVERS_NE2000_H__ */ diff --git a/drivers/net/ne2000_base.h b/drivers/net/ne2000_base.h new file mode 100644 index 0000000000..1badf62bf2 --- /dev/null +++ b/drivers/net/ne2000_base.h @@ -0,0 +1,282 @@ +/* +Ported to U-Boot by Christian Pellegrin + +Based on sources from the Linux kernel (pcnet_cs.c, 8390.h) and +eCOS(if_dp83902a.c, if_dp83902a.h). Both of these 2 wonderful world +are GPL, so this is, of course, GPL. + + +========================================================================== + + dev/dp83902a.h + + National Semiconductor DP83902a ethernet chip + +========================================================================== +####ECOSGPLCOPYRIGHTBEGIN#### + ------------------------------------------- + This file is part of eCos, the Embedded Configurable Operating System. + Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc. + + eCos is free software; you can redistribute it and/or modify it under + the terms of the GNU General Public License as published by the Free + Software Foundation; either version 2 or (at your option) any later version. + + eCos is distributed in the hope that it will be useful, but WITHOUT ANY + WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + for more details. + + You should have received a copy of the GNU General Public License along + with eCos; if not, write to the Free Software Foundation, Inc., + 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA. + + As a special exception, if other files instantiate templates or use macros + or inline functions from this file, or you compile this file and link it + with other works to produce a work based on this file, this file does not + by itself cause the resulting work to be covered by the GNU General Public + License. However the source code for this file must still be made available + in accordance with section (3) of the GNU General Public License. + + This exception does not invalidate any other reasons why a work based on + this file might be covered by the GNU General Public License. + + Alternative licenses for eCos may be arranged by contacting Red Hat, Inc. + at http://sources.redhat.com/ecos/ecos-license/ + ------------------------------------------- +####ECOSGPLCOPYRIGHTEND#### +####BSDCOPYRIGHTBEGIN#### + + ------------------------------------------- + + Portions of this software may have been derived from OpenBSD or other sources, + and are covered by the appropriate copyright disclaimers included herein. + + ------------------------------------------- + +####BSDCOPYRIGHTEND#### +========================================================================== +#####DESCRIPTIONBEGIN#### + + Author(s): gthomas + Contributors: gthomas, jskov + Date: 2001-06-13 + Purpose: + Description: + +####DESCRIPTIONEND#### + +========================================================================== + +*/ + +/* + ------------------------------------------------------------------------ + Macros for accessing DP registers + These can be overridden by the platform header +*/ + +#define bool int + +#define false 0 +#define true 1 + +/* timeout for tx/rx in s */ +#define TOUT 5 +/* Ether MAC address size */ +#define ETHER_ADDR_LEN 6 + + +#define CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA 1 +#define CYGACC_CALL_IF_DELAY_US(X) udelay(X) + +/* H/W infomation struct */ +typedef struct hw_info_t { + u32 offset; + u8 a0, a1, a2; + u32 flags; +} hw_info_t; + +typedef struct dp83902a_priv_data { + u8* base; + u8* data; + u8* reset; + int tx_next; /* First free Tx page */ + int tx_int; /* Expecting interrupt from this buffer */ + int rx_next; /* First free Rx page */ + int tx1, tx2; /* Page numbers for Tx buffers */ + u32 tx1_key, tx2_key; /* Used to ack when packet sent */ + int tx1_len, tx2_len; + bool tx_started, running, hardwired_esa; + u8 esa[6]; + void* plf_priv; + + /* Buffer allocation */ + int tx_buf1, tx_buf2; + int rx_buf_start, rx_buf_end; +} dp83902a_priv_data_t; + +/* + ------------------------------------------------------------------------ + Some forward declarations +*/ +int get_prom( u8* mac_addr); +static void dp83902a_poll(void); + +/* ------------------------------------------------------------------------ */ +/* Register offsets */ + +#define DP_CR 0x00 +#define DP_CLDA0 0x01 +#define DP_PSTART 0x01 /* write */ +#define DP_CLDA1 0x02 +#define DP_PSTOP 0x02 /* write */ +#define DP_BNDRY 0x03 +#define DP_TSR 0x04 +#define DP_TPSR 0x04 /* write */ +#define DP_NCR 0x05 +#define DP_TBCL 0x05 /* write */ +#define DP_FIFO 0x06 +#define DP_TBCH 0x06 /* write */ +#define DP_ISR 0x07 +#define DP_CRDA0 0x08 +#define DP_RSAL 0x08 /* write */ +#define DP_CRDA1 0x09 +#define DP_RSAH 0x09 /* write */ +#define DP_RBCL 0x0a /* write */ +#define DP_RBCH 0x0b /* write */ +#define DP_RSR 0x0c +#define DP_RCR 0x0c /* write */ +#define DP_FER 0x0d +#define DP_TCR 0x0d /* write */ +#define DP_CER 0x0e +#define DP_DCR 0x0e /* write */ +#define DP_MISSED 0x0f +#define DP_IMR 0x0f /* write */ +#define DP_DATAPORT 0x10 /* "eprom" data port */ + +#define DP_P1_CR 0x00 +#define DP_P1_PAR0 0x01 +#define DP_P1_PAR1 0x02 +#define DP_P1_PAR2 0x03 +#define DP_P1_PAR3 0x04 +#define DP_P1_PAR4 0x05 +#define DP_P1_PAR5 0x06 +#define DP_P1_CURP 0x07 +#define DP_P1_MAR0 0x08 +#define DP_P1_MAR1 0x09 +#define DP_P1_MAR2 0x0a +#define DP_P1_MAR3 0x0b +#define DP_P1_MAR4 0x0c +#define DP_P1_MAR5 0x0d +#define DP_P1_MAR6 0x0e +#define DP_P1_MAR7 0x0f + +#define DP_P2_CR 0x00 +#define DP_P2_PSTART 0x01 +#define DP_P2_CLDA0 0x01 /* write */ +#define DP_P2_PSTOP 0x02 +#define DP_P2_CLDA1 0x02 /* write */ +#define DP_P2_RNPP 0x03 +#define DP_P2_TPSR 0x04 +#define DP_P2_LNPP 0x05 +#define DP_P2_ACH 0x06 +#define DP_P2_ACL 0x07 +#define DP_P2_RCR 0x0c +#define DP_P2_TCR 0x0d +#define DP_P2_DCR 0x0e +#define DP_P2_IMR 0x0f + +/* Command register - common to all pages */ + +#define DP_CR_STOP 0x01 /* Stop: software reset */ +#define DP_CR_START 0x02 /* Start: initialize device */ +#define DP_CR_TXPKT 0x04 /* Transmit packet */ +#define DP_CR_RDMA 0x08 /* Read DMA (recv data from device) */ +#define DP_CR_WDMA 0x10 /* Write DMA (send data to device) */ +#define DP_CR_SEND 0x18 /* Send packet */ +#define DP_CR_NODMA 0x20 /* Remote (or no) DMA */ +#define DP_CR_PAGE0 0x00 /* Page select */ +#define DP_CR_PAGE1 0x40 +#define DP_CR_PAGE2 0x80 +#define DP_CR_PAGEMSK 0x3F /* Used to mask out page bits */ + +/* Data configuration register */ + +#define DP_DCR_WTS 0x01 /* 1=16 bit word transfers */ +#define DP_DCR_BOS 0x02 /* 1=Little Endian */ +#define DP_DCR_LAS 0x04 /* 1=Single 32 bit DMA mode */ +#define DP_DCR_LS 0x08 /* 1=normal mode, 0=loopback */ +#define DP_DCR_ARM 0x10 /* 0=no send command (program I/O) */ +#define DP_DCR_FIFO_1 0x00 /* FIFO threshold */ +#define DP_DCR_FIFO_2 0x20 +#define DP_DCR_FIFO_4 0x40 +#define DP_DCR_FIFO_6 0x60 + +#define DP_DCR_INIT (DP_DCR_LS|DP_DCR_FIFO_4) + +/* Interrupt status register */ + +#define DP_ISR_RxP 0x01 /* Packet received */ +#define DP_ISR_TxP 0x02 /* Packet transmitted */ +#define DP_ISR_RxE 0x04 /* Receive error */ +#define DP_ISR_TxE 0x08 /* Transmit error */ +#define DP_ISR_OFLW 0x10 /* Receive overflow */ +#define DP_ISR_CNT 0x20 /* Tally counters need emptying */ +#define DP_ISR_RDC 0x40 /* Remote DMA complete */ +#define DP_ISR_RESET 0x80 /* Device has reset (shutdown, error) */ + +/* Interrupt mask register */ + +#define DP_IMR_RxP 0x01 /* Packet received */ +#define DP_IMR_TxP 0x02 /* Packet transmitted */ +#define DP_IMR_RxE 0x04 /* Receive error */ +#define DP_IMR_TxE 0x08 /* Transmit error */ +#define DP_IMR_OFLW 0x10 /* Receive overflow */ +#define DP_IMR_CNT 0x20 /* Tall counters need emptying */ +#define DP_IMR_RDC 0x40 /* Remote DMA complete */ + +#define DP_IMR_All 0x3F /* Everything but remote DMA */ + +/* Receiver control register */ + +#define DP_RCR_SEP 0x01 /* Save bad(error) packets */ +#define DP_RCR_AR 0x02 /* Accept runt packets */ +#define DP_RCR_AB 0x04 /* Accept broadcast packets */ +#define DP_RCR_AM 0x08 /* Accept multicast packets */ +#define DP_RCR_PROM 0x10 /* Promiscuous mode */ +#define DP_RCR_MON 0x20 /* Monitor mode - 1=accept no packets */ + +/* Receiver status register */ + +#define DP_RSR_RxP 0x01 /* Packet received */ +#define DP_RSR_CRC 0x02 /* CRC error */ +#define DP_RSR_FRAME 0x04 /* Framing error */ +#define DP_RSR_FO 0x08 /* FIFO overrun */ +#define DP_RSR_MISS 0x10 /* Missed packet */ +#define DP_RSR_PHY 0x20 /* 0=pad match, 1=mad match */ +#define DP_RSR_DIS 0x40 /* Receiver disabled */ +#define DP_RSR_DFR 0x80 /* Receiver processing deferred */ + +/* Transmitter control register */ + +#define DP_TCR_NOCRC 0x01 /* 1=inhibit CRC */ +#define DP_TCR_NORMAL 0x00 /* Normal transmitter operation */ +#define DP_TCR_LOCAL 0x02 /* Internal NIC loopback */ +#define DP_TCR_INLOOP 0x04 /* Full internal loopback */ +#define DP_TCR_OUTLOOP 0x08 /* External loopback */ +#define DP_TCR_ATD 0x10 /* Auto transmit disable */ +#define DP_TCR_OFFSET 0x20 /* Collision offset adjust */ + +/* Transmit status register */ + +#define DP_TSR_TxP 0x01 /* Packet transmitted */ +#define DP_TSR_COL 0x04 /* Collision (at least one) */ +#define DP_TSR_ABT 0x08 /* Aborted because of too many collisions */ +#define DP_TSR_CRS 0x10 /* Lost carrier */ +#define DP_TSR_FU 0x20 /* FIFO underrun */ +#define DP_TSR_CDH 0x40 /* Collision Detect Heartbeat */ +#define DP_TSR_OWC 0x80 /* Collision outside normal window */ + +#define IEEE_8023_MAX_FRAME 1518 /* Largest possible ethernet frame */ +#define IEEE_8023_MIN_FRAME 64 /* Smallest possible ethernet frame */